MACHINE SPECIFICATION

C10T.14
C10T.14
OIL COUNTRY LATHES
STANDART MACHINE SPECIFICATION UNIT C10T.14
CAPACITY Height of centers mm 510
Swing over bed mm 1020
Swing over cross slide mm 780
Swing in gap mm 1210
Width of bed mm 560
Distance between centers mm 1500; 2000; 3000; 4000; 5000; 6000
SPINDLE Spindle nose DIN 55027 No A2.20
Spindle bore mm 358
Spindle taper Metric 318
HEAD STOCK Number of spindle speeds 12
Spindle variable speed sub-ranges rpm 6,3 — 315
Main motor power kw 18,5
FEEDS Number of feeds 152
Longitudinal feed range mm/rev 0,039 — 15
Cross feed range mm/rev 0,02 — 7,5
THREADS Number of threads 64
Metric thread range mm 0,5 — 150
Inch thread range Tpi 60 — 1/5
Module thread range Module 0,125 — 37,5
DP thread range DP 240 — 4/5
CARRIAGE Cross slide travel mm 510
Top slide travel mm 280
TAIL STOCK Quill diameter mm 105
Quill taper Morse No.6
Quill travel mm 225
LATHE MACHINE OPTIONAL ACCESSORIES
N OPTIONAL SPECIFICATIONS CU325 C400TM CU400 CU500 CU400M CU500M CU580M C11MT CU500MT CU630
ACCESSORY CU325RD C400TMS CU400MRD CU500MRD CU580MRD C11MTS CU500MTRD CU630RD
1 3-JAW SELFCENTERING CHUCK Diameter (mm) 160 200 250 250 250 250 250 250 315 315
2 INDEPENDENT 4-JAW CHUCK Diameter (mm) 250 320 400 500 400 500 500 500 500 600
3 FACE PLATE Diameter (mm) 296 320 400 480 400 480 480 480 500 600
4 FOLLOWE REST Range (mm) 10-70 10-80 15-160 15-200 15-160 15-200 15-200 15-200 15-200 15-200
5 STEADY REST, SMALL SIZE Range (mm) 10-70 10-100 15-150 15-160 15-160 15-160 15-200 15-200 15-160 15-200
6 STEADY REST, BIG SIZE Range (mm) No No No 140-280 No 140-280 180-340 180-340 140-280 180-340

7 TAPER TURNING ATTACHM. +10O Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
8 ONE-POSITION LONG. STOP Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
9 THREAD DIAL Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
10 DRIVE PLATE FOR SPINDLE Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
NOSE DIN 55027
11 SET OF LATHE DOGS 20; 30; 40; 20; 50; 20;30;40; Full Full Full Full Full Full Full Full
50; 60; 80; 100 50;60
12 LIVE CENTER Morse M3 M4 M5 M5 M5 M5 M5 M5 M5 M5

13 DRILL CHUCK WITH ARBOR Drill diam. (mm) 13 20 20 20 20 20 20 20 20 20

N OPTIONAL SPECIFICATIONS C10T CU730 C10TM C10TH C10T.10 C10T.12 CU800 CU1000 CU1250 CU1410RD
ACCESSORY C10TS CU730RD C10TMS C10THS C10TS.10 C10TS.12 CU800RD CU1000RD CU1250RD
1 3-JAW SELFCENTERING CHUCK Diameter (mm) 315 315 400 400 500 500 500 500 500 630
2 INDEPENDENT 4-JAW CHUCK Diameter (mm) 600 600 760 760 580 630 Stan- 760 1000 1000 1250
Standard dard
3 FACE PLATE Diameter (mm) 600 600 760 760 x x 760 1000 1000 No
4 FOLLOWE REST Range (mm) 15-200 20-200 20-200 20-200 20-200 20-200 80-300 80-300 80-300 80-300
5 STEADY REST, SMALL SIZE Range (mm) 15-200 20-200 20-200 50-250 20-200 20-200 50-300 50-300 50-300 80-300
6 STEADY REST, BIG SIZE Range (mm) 180-430 180-430 180-430 220-450 180-430 180-430 270-520 270-520 270-520 270-520
200-520 420-620 480-720 480-720 470-720
700-950 700-1000
7 TAPER TURNING ATTACHM. +10O Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
Standard Standard
8 ONE-POSITION LONG. STOP Yes Yes Yes Yes Yes Yes No No No Yes
9 THREAD DIAL Yes Yes Yes Yes Yes Yes Yes Yes Yes No
Standard Standard
10 DRIVE PLATE FOR SPINDLE NOSE Yes Yes Yes Yes No No No No No No
DIN 55027
11 SET OF LATHE DOGS 20; 30; 40; Full Full Full Full No No No No No No
50; 60; 80; 100
12 LIVE CENTER Morse M5 M6 M6 M6 M6 M6 M6 M6 M6 MK 7

13 DRILL CHUCK WITH ARBOR Drill diam. (mm) 20 20 20 20 No No No No No No

Remarks : Yes = Available for this model; No = Not available for this model
Steady rest 720mm for lathe CU1000 - open type only
Steady rest 700-1000 for lathe CU1410RD - open type only