Australian Standard: Particleboard Flooring Part 2: Installation

Download as pdf or txt
Download as pdf or txt
You are on page 1of 7

AS 1860.

2—2006
(Incorporating Amendment No. 1)
Reconfirmed 2016
AS 1860.2—2006

Australian Standard®
This is a free 6 page sample. Access the full version online.

Particleboard flooring

Part 2: Installation
This Australian Standard® was prepared by Committee TM-005, Reconstituted Timber Panel
Products. It was approved on behalf of the Council of Standards Australia on 19 May 2006.
This Standard was published on 26 June 2006.

The following are represented on Committee TM-005:

• Australian Building Codes Board


• Australian Wood Panels Association
• Ensis
• Forests NSW
• Furnishing Industry Association of Australia
• Furntech
• Master Builders Australia
• New Zealand Wood Panel Manufacturers Association

Additional Interests:
This is a free 6 page sample. Access the full version online.

• Dr Alan Halligan

This Standard was issued in draft form for comment as DR 02548.

Standards Australia wishes to acknowledge the participation of the expert individuals that
contributed to the development of this Standard through their representation on the
Committee and through the public comment period.

Keeping Standards up-to-date


Australian Standards® are living documents that reflect progress in science, technology and
systems. To maintain their currency, all Standards are periodically reviewed, and new editions
are published. Between editions, amendments may be issued.

Standards may also be withdrawn. It is important that readers assure themselves they are
using a current Standard, which should include any amendments that may have been
published since the Standard was published.

Detailed information about Australian Standards, drafts, amendments and new projects can
be found by visiting www.standards.org.au

Standards Australia welcomes suggestions for improvements, and encourages readers to


notify us immediately of any apparent inaccuracies or ambiguities. Contact us via email at
[email protected], or write to Standards Australia, GPO Box 476, Sydney, NSW 2001.
AS 1860.2—2006 (Reconfirmed) 2016-06-17

STANDARDS AUSTRALIA

RECONFIRMATION
OF
AS 1860.2—2006
Particleboard flooring
Part 2: Installation

RECONFIRMATION NOTICE

Technical Committee TM-011 has reviewed the content of this publication and in
accordance with Standards Australia procedures for reconfirmation, it has been
determined that the publication is still valid and does not require change.

Certain documents referenced in the publication may have been amended since the
This is a free 6 page sample. Access the full version online.

original date of publication. Users are advised to ensure that they are using the latest
versions of such documents as appropriate, unless advised otherwise in this
Reconfirmation Notice.

Approved for reconfirmation in accordance with Standards Australia procedures for


reconfirmation on 27 April 2016.

The following are represented on Technical Committee TM-011:


Australian Building Codes Board
Australian Forest Products Association
Australian Timber Importers Federation
Australian Wood Panels Association
Building Research Association of New Zealand
Engineered Wood Products Association of Australasia
Forest and Wood Products Australia
Furntech-AFRDI
Glued Laminated Timber Association of Australia
Master Builders Australia
Monash University
New Zealand Plywood Manufacturers Association
New Zealand Timber Industry Federation
Timber Design Society
Wood Processors & Manufacturers Association of New Zealand
This is a free 6 page sample. Access the full version online.

NOTES
AS 1860.2—2006
(Incorporating Amendment No. 1)

Australian Standard®
This is a free 6 page sample. Access the full version online.

Particleboard flooring

Part 2: Installation

Originated as AS 1860—1974.
Previous edition AS 1860—1991.
Fourth edition 1998.
Revised and redesignated as AS 1860.2—2006.
Reissued incorporating Amendment No. 1 (December 2010).

COPYRIGHT
© Standards Australia Limited
All rights are reserved. No part of this work may be reproduced or copied in any form or by
any means, electronic or mechanical, including photocopying, without the written
permission of the publisher, unless otherwise permitted under the Copyright Act 1968.
Published by SAI Global Limited under licence from Standards Australia Limited, GPO Box
476, Sydney, NSW 2001, Australia
ISBN 0 7337 7529 2
AS 1860.2—2006 2

PREFACE
This Standard was prepared by the Joint Standards Australia/ Standards New Zealand
Committee TM-005, Reconstituted Timber Panel Products, to supersede AS 1860—1998,
Installation of particleboard flooring. After consultation with stakeholders in both
countries, Standards Australia and Standards New Zealand decided to develop this Standard
as an Australian Standard rather than an Australian/New Zealand Standard.
This Standard incorporates Amendment No. 1 (December 2010). The changes required by
the Amendment are indicated in the text by a marginal bar and amendment number against
the clause, note, table, figure, or part thereof affected.
The objective of this Standard is to set out the minimum performance requirements for the
installation of particleboard flooring, which are acceptable to building authorities in
Australia.
The objective of this revision is to provide a series of Standard series that deals with
particleboard flooring, as follows:
AS/NZS 1860 Particleboard flooring
This is a free 6 page sample. Access the full version online.

AS/NZS 1860.1 Part 1: Specifications


AS 1860.2 Part 2: Installation (this Standard)
An informative Appendix D has been incorporated to provide guidelines for flooring
installation in wet areas.
During the course of preparation of this Standard, consideration was given to research and
testing information from resources in Australia, New Zealand and overseas.
This Standard will be referenced in the Building Code of Australia 2007, thereby
superseding the previous edition, AS 1860—1998, which will be withdrawn 12 months
from the date of publication of this edition.
The term ‘informative’ has been used in this Standard to define the application of the
appendix to which it applies. An ‘informative’ appendix is only for information and
guidance.
This is a free preview. Purchase the entire publication at the link below:

AS 1860.2-2006 (R2016) Particleboard flooring -


Installation
This is a free 6 page sample. Access the full version online.

Looking for additional Standards? Visit SAI Global Infostore


Subscribe to our Free Newsletters
Do you need to Manage Standards Collections Online?
Learn about LexConnect, All Jurisdictions, Standards referenced in Australian legislation
Do you want to know when a Standard has changed?
Create safe work processes for the workplace with our Safe Work Method Statements

Learn about other SAI Global Services:

LOGICOM Military Parts and Supplier Database


Metals Infobase Database of Metal Grades, Standards and Manufacturers
Materials Infobase Database of Materials, Standards and Suppliers
Database of European Law, CELEX and Court Decisions

Need to speak with a Customer Service Representative - Contact Us

You might also like