Scribd
Upload
251 views

24 Bit Aircraft ID Programming

This EASA Safety Information Bulletin notifies aircraft owners and operators about incorrect settings of ICAO 24-bit aircraft addresses in Mode S transponders. It reports that Eurocontrol's Mode-S Airborne Monitoring Project has identified a significant number of aircraft operating with incorrect addresses. Incorrect addresses can cause potentially hazardous situations, degrade air traffic control and ACAS collision avoidance systems. The SIB recommends that operators check their aircraft's address and rectify it if incorrect, and verify proper transponder operation every two years with ground testing. It provides guidance on conducting ground tests to check transponder function without disrupting air traffic control.

Uploaded by

Aidan Monaghan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
251 views

24 Bit Aircraft ID Programming

This EASA Safety Information Bulletin notifies aircraft owners and operators about incorrect settings of ICAO 24-bit aircraft addresses in Mode S transponders. It reports that Eurocontrol's Mode-S Airborne Monitoring Project has identified a significant number of aircraft operating with incorrect addresses. Incorrect addresses can cause potentially hazardous situations, degrade air traffic control and ACAS collision avoidance systems. The SIB recommends that operators check their aircraft's address and rectify it if incorrect, and verify proper transponder operation every two years with ground testing. It provides guidance on conducting ground tests to check transponder function without disrupting air traffic control.

Uploaded by

Aidan Monaghan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

EASA SIB No: 2011-14

EASA Safety Information Bulletin

SIB No.: 2011-14

Issued: 04 July 2011

Subject: Mode S Transponder – Incorrect Setting of ICAO 24-Bit


Aircraft Address

Ref. Publications: Annex 10 to the Convention on International Civil Aviation,


Aviation
Volume III – Communications Systems.
EASA SIB No: 2011-15 - Mode S Transponder: Ground Testing.

Applicability: All owners and operators of aircraft having SSR Mode S


transponders installed.
Mode S transponders are known to be installed on, but not
limited to, aircraft certificated under (FAR, JAR, CS) Part 22, 23,
25, 27, 29, 31HB, VLA or VLR.

Description: The Mode-S Airborne Monitoring Project (AMP), which is


coordinated by Eurocontrol, has identified a significant number
of aircraft operating within European airspace with incorrect
ICAO 24-bit aircraft addresses.
The provision of air traffic services (ATS) using SSR Mode S
relies wholly upon a unique ICAO 24-bit aircraft address for
selective interrogation of individual aircraft. The unique 24-bit
aircraft address is also an essential element of the airborne
collision and avoidance system, ACAS II.
At this time, the airworthiness concern described in this SIB is
not considered to be an unsafe condition that would warrant
Airworthiness Directive (AD) action under EC 1702/2003, Part
21A.3B.
Nevertheless, when two (or more) aircraft with the same
(duplicate) ICAO 24-bit aircraft address are operating within
range of a specific Mode S interrogator, then potentially
hazardous situations can arise:
 One (or more) of the aircraft involved may be assessed
by the Mode S interrogator to be a false or reflected
echo, and subsequently ignored. These aircraft will not
then be displayed to air traffic controllers.

This is information only. Recommendations are not mandatory.


EASA Form 117 Page 1/3
EASA SIB No: 2011-14

 In the case of aircraft whose flight paths cross, the


identification labels of those aircraft may inadvertently
‘swap’ (i.e. replace one another) on air traffic controllers
displays, thereby presenting controllers with incorrect
information and creating the possibility of
misidentification.
 The performance of ACAS II systems could be seriously
degraded or even disabled.
Any incorrect aircraft address is, potentially, a duplicate
address, because it has not been legitimately assigned to that
airframe. The potential for duplication rises dramatically in
cases of incorrect addresses where values such as all 0’s or all
1’s have been set.

Recommendations: If you become aware, or are notified, that your aircraft has an
incorrect ICAO 24-bit aircraft address, EASA recommends that
you take action to ensure that the address, as assigned to your
aircraft by the State of Registry or common mark registering
authority, is set correctly at the earliest opportunity.
In addition, confirmation that the assigned ICAO 24-bit aircraft
address is being transmitted should be obtained.
Aircraft operators/owners will be notified of an incorrect ICAO
24-bit aircraft address via their National Aviation Authority
(NAA), or Air Navigation Service Provider. To ensure that the
notifying authority can track the resolution of such issues, it is
highly recommended that operators/owners promptly advise the
notifying authority about any rectification action.
The ICAO 24-bit aircraft address is normally set in the Mode S
transponder, but it can be set in other items of interchangeable
airborne avionic equipment. In order to ensure that the
assigned ICAO 24-bit aircraft address is transmitted, EASA
recommends that the operation of installed Mode S transponder
systems is verified using appropriate ramp testing equipment at
intervals not exceeding 2 years, in accordance with in
accordance with appropriate maintenance manual procedures
and using calibrated ramp test equipment.
Guidance for the ground testing of transponders can be found in
Appendix 1 of this SIB.
Note 1: In case the ramp test equipment indicates an error with
the transmission of data, or indicates any other type of failure
(e.g. out of frequency, power etc), the problem should be
corrected prior to the next flight.
Note 2: Aircraft manufacturers may wish to apply to their NAA
for a ‘block’ of ICAO 24-bit aircraft addresses exclusively for use
during development and production acceptance flights.

Contacts: For further information contact the Safety Information Section,


Executive Directorate, EASA; E-mail: [email protected].

This is information only. Recommendations are not mandatory.


EASA Form 117 Page 2/3
EASA SIB No: 2011-14

Appendix 1 - Transponder Ground Testing Guidance

a. When not required, ensure all transponders are selected to ‘OFF’ or ‘Standby’.
b. Before starting any test, contact the local Air Traffic Control Unit and advise them of your
intention to conduct transponder testing. Advise the Air Traffic Unit of your start time and
test duration. Also inform them of the altitude(s) at which you will be testing, your
intended Aircraft Identification (Flight Id) and your intended Mode A code. See para c
and d. Note: Certain altitudes may not be possible due to over flying aircraft.
c. Set the Mode A code to 7776 (or other Mode A code agreed with Air Traffic Control
Unit). Note: The Mode A code 7776 is assigned as a test code by the ORCAM Users
Group, specifically for the testing of transponders.
d. Set the Aircraft Identification (Flight Id) with the first 8 characters of the company name.
This is the name of the company conducting the tests.
e. Set the on-the-ground status for all Mode S replies, except when an airborne reply is
required (e.g. for altitude testing).
f. Where possible, perform the testing inside a hanger to take advantage of any shielding
properties it may provide.
g. As a precaution, use antenna transmission covers whether or not testing is performed
inside or outside.
h. When testing the altitude (Mode C or S) parameter, radiate directly into the ramp test set
via the prescribed attenuator.
i. In between testing, i.e. to transition from one altitude to another, select the transponder
to ‘standby’ mode.
j. If testing transponder parameters other than ‘altitude’, set altitude to -1000 feet (minus
1000 feet), or over 60000 feet. This will minimise the possibility of ACAS warning to
airfield and overflying aircraft.
k. When testing is complete select the transponder(s) to ‘OFF’ or ‘Standby’.

This is information only. Recommendations are not mandatory.


EASA Form 117 Page 3/3

You might also like