Service Manual Ve d12

Download as pdf or txt
Download as pdf or txt
You are on page 1of 32

Service Manual

Trucks
Group 200-820
Specifications
VE D12

V776-200-820SM
Foreword
The descriptions and service procedures contained in this manual are based on de-
signs and methods studies carried out up to August 95.

The products are under continuous development. Vehicles and components produced
after the above date may therefore have different specifications and repair methods.
When this is believed to have a significant bearing on this manual, supplementary ser-
vice bulletins will be issued to cover the changes.

The new edition of this manual will update the changes.

In service procedures where the title incorporates an operation number, this is a refer-
ence to an S.R.T. (Standard Repair Time).

Service procedures which do not include an operation number in the title are for gen-
eral information and no reference is made to an S.R.T.

The following levels of observations, cautions and warnings are used in this Service
Documentation:

Note: Indicates a procedure, practice, or condition that must be followed in order to


have the vehicle or component function in the manner intended.

Caution: Indicates an unsafe practice where damage to the product could occur.

Warning: Indicates an unsafe practice where personal injury or severe damage to the
product could occur.

Danger: Indicates an unsafe practice where serious personal injury or death could oc-
cur.

Volvo Trucks North America, Inc.


Greensboro, NC USA

Order number: V776-200-820SM

© 95 Volvo Trucks North America, Inc., Greensboro, NC USA

All rights reserved. No part of this publication may be reproduced, stored in


retrieval system, or transmitted in any forms by any means, electronic, me-
chanical, photocopying, recording or otherwise, without the prior written
permission of Volvo Trucks North America, Inc..
Contents
Specifications ......................................................................................... 3
Engine .................................................................................................... 3
Lubrication and Oil System ................................................................. 17
Fuel System ......................................................................................... 19
Cooling System ................................................................................... 20
Wear Tolerances .................................................................................. 21
Tightening Torques .............................................................................. 23

1
2
Group 20 Specifications, VE D12 Specifications

Specifications
Engine

W2000698

Fig. 1: VE D12 Engine

1 Serial Number Location

Model Designations

VE D12–310
Max. Power .................... 232 kW (310 Hp) @ 1700 rpm
Max. Torque .... 1694 Nm (1254 lb-ft) @ 1100-1300 rpm

VE D12–335
Max. Power .................... 259 kW (335 Hp) @ 1700 rpm
Max. Torque .... 1762 Nm (1304 lb-ft) @ 1100-1300 rpm

VE D12–370
Max. Power .................... 276 kW (370 Hp) @ 1700 rpm
Max. Torque .... 1762 Nm (1304 lb-ft) @ 1100-1400 rpm

VE D12–415
Max. Power .................... 310 kW (415 Hp) @ 1700 rpm
Max. Torque .... 1850 Nm (1369 ft-lb) @ 1100-1500 rpm

3
Group 20 Specifications, VE D12 Specifications

Number of Cylinders .................................................... 6


Number of Valves ................................... 24 per Cylinder
Bore 131 mm ....................................................... (5.2 in)
Stroke 150 mm .................................................... (5.9 in)
Displacement ..................................... 12 Liters (740 in3)
Compression Ratio ............................................... 17.5:1
Firing Sequence ........................................... 1-5-3-6-2-4
Low Idle ...................................................... 500-650 rpm
High Idle ................................................. 2065 ± 20 rpm
Maximum Full Load Speed ............................. 1900 rpm
Weight, Engine With Flywheel, Flywheel Housing and
Starter Motor (Dry) ............................. 1060 kg (2332 lb)
Length ................................................... 1348 mm (53 in)
Width ................................................... 780 mm (30.7 in)
Height ................................................ 1138 mm (44.8 in)

W2000699

Fig. 2: Performance curves

Cylinder Head
Type ................................................................. 6 cylinder
Length ............................................ 1076 mm (42.36 in)
Width ............................................... 373 mm (14.68 in)
Height ................................................. 135 mm (5.31 in)

Cylinder Head Bolts

Number 38

Thread size M16

Length 200 mm (7.87 in)

4
Group 20 Specifications, VE D12 Specifications

Cylinder Block
Height above block face, crankshaft cen- 422 mm
ter (A) minimum (16.61 in)

Height, lower block face, crankshaft cen- 120 mm


ter (B) minimum (4.72 in)

T2006964

Fig. 3: Cylinder block

Cylinder Liner
Type Wet, replaceable

Sealing surface height 0.15–0.20 mm (0.0059–


above face 0.0078 in)

Number of O-rings, cylin- 4


der liner

5
Group 20 Specifications, VE D12 Specifications

Piston
Height above cylinder 0.15–0.65 mm (0.0059–
block face 0.0255 in)

Diameter, combustion 86 mm (3.38 in)


chamber

Depth, piston ball 19.7 mm (0.775 in)

Number of ring grooves 3

Front marking Arrow pointing forward

Piston Rings, Compression


Number 2

Piston ring clearance in groove:

Upper compression ring Keystone

Lower compression ring 0.070–0.102 mm


(0.0027–0.004 in)

Piston ring gap measured in ring opening:

Upper ring 0.40–0.65 mm (0.015–


0.0255 in)

Lower ring 0.8–1.0 mm (0.031–0.039


in)

Piston Rings, Oil Control Ring


Number 1

Width, including spring 4.88 mm (0.192 in)

Piston ring clearance in 0.050–0.082 mm


groove (0.0019–0.0032 in)

Piston ring gap measured 0.40–0.75 mm (0.0157–


in ring opening 0.0295 in)

6
Group 20 Specifications, VE D12 Specifications

Valves, VE D12
Valve disc diameter: Valve clearance, cold engine, setting value:

Intake 40 ± 0.1 mm (1.57 ± Intake 0.2 mm (0.0078 in)


0.0039 in)
Exhaust 0.5 mm (0.0196 in)
Exhaust 40 ± 0.1 mm (1.57 ±
0.0039 in) Exhaust, VEB 1.6 mm (0.0629 in)

Valve stem diameter: Valve clearance, cold engine, checking value:

Intake 7.964–7.975 mm Intake 0.15–0.25 mm (0.0059–


(0.3135–0.3140 in) 0.0098 in)

Exhaust 7.951–7.962 mm (0.313– Exhaust 0.45–0.55 mm (0.0177–


0.3135 in) 0.0216 in)

Valve seat angle: Exhaust, VEB 1.55–1.65 mm (0.061–


0.065 in)

Intake 29.5


Exhaust 44.5

Valve disc edge:

Intake 1.76 mm (0.069 in)


T2006963

Fig. 4: Valve angles


Exhaust 1.57 mm (0.061 in)

Seat angle in cylinder head:


Intake 30


Exhaust 45

7
Group 20 Specifications, VE D12 Specifications

Valve Seats Valve Seat Location


Outer diameter Standard (measurement A: Diameter standard (measurement C):

Intake 43.070–43.086 mm Intake 43.000–43.025 mm (1.693–1.694


(1.695–1.696 in) in)

Exhaust 43.070–43.086 mm Exhaust 43.000–43.025 mm (1.693–1.694


(1.695–1.696 in) in)

Oversize: Diameter oversize (measurement C):

Intake 43.270–43.286 mm Intake 43.200–43.225 mm (1.701–1.702


(1.703–1.704 in) in)

Exhaust 43.270–43.286 mm Exhaust 43.200–43.225 mm (1.701–1.702


(1.703–1.704 in) in)

Height (measurement B): Depth (measurement D):

Intake 8.5–8.7 mm (0.335–0.343 Intake 11.2 ± 0.1 mm (0.44 ± 0.004 in)


in)
Exhaust 11.2 ± 0.1 mm (0.44 ± 0.004 in)

Seat bottom radius (measurement R):

Intake, maximum 0.8 mm (0.03 in)

Exhaust, maxi- 0.8 mm (0.03 in)


T2006961
mum
Fig. 5: Valve seats

Measurement between valve disc and cylinder head


face:

Intake 0.9–1.4 mm (0.035–0.055 in)

Exhaust 1.2–1.7 mm (0.047–0.067 in)

T2006962

Fig. 6: Valve seat location

8
Group 20 Specifications, VE D12 Specifications

Valve Guides
Length:

Intake 83.2–83.5 mm (3.28–3.29 in)

Exhaust 83.2–83.5 mm (3.28–3.29 in)

Inner diameter:

Intake 8.000–8.015 mm (0.315–0.316 in)

Exhaust 8.000–8.015 mm (0.315–0.316 in)

Height above cylinder head spring face:

Intake 26.5 ± 0.35 mm (1.0 ± 0.01 in)

Exhaust 18.5 ± 0.35 mm (0.73 ± 0.01 in)

Clearance valve stem-guide:

Intake 0.025–0.051 mm (0.0009–0.003 in)

Exhaust 0.038–0.064 mm (0.001–0.003 in)

Rocker arms:

Bearing clear- 0.03–0.08 mm (0.001–0.003 in)


ance

9
Group 20 Specifications, VE D12 Specifications

Valve Springs, Exhaust


Outer valve spring:

Length, unloaded 72.4 mm (2.85 in)

With load of 600 Nm (135 55.9 mm (2.2 in)


ft-lb)

With load of 1076 Nm 42.8 mm (1.68 in)


(242 ft-lb)

Rigid length, maximum 41.2 mm (1.62 in)

Inner valve spring:

Length, unloaded 67.5 mm (2.65 in)

With load of 243 Nm (55 51.9 mm (2.04 in)


ft-lb)

With load of 447 Nm (100 38.8 mm (1.52 in)


ft-lb)

Rigid length, maximum 35.7 mm (1.40 in)

Valve Springs, Intake


Length, unloaded 72.4 mm (2.85 in)

With load of 600 Nm (135 55.9 mm (2.2 in)


lb-ft)

With load of 1076 Nm 42.8 mm (1.68 in)


(242 lb-ft)

Rigid length, maximum 41.2 mm (1.62 in)

10
Group 20 Specifications, VE D12 Specifications

Timing Gears
Ref. No. Description No. of Teeth

1 Crankshaft Drive Gear 36

2 Idler Gear 87

3 Water Pump Drive Gear 24

4 Air Compressor Drive Gear 27

5 Camshaft 72

6 Adjustable Idler Gear 58

7 Upper Idler Gear 60

8 Lower Idler Gear 58

9 Power Steering Pump Drive 22


Gear

10 Drive Gear Arrangement 26


(Accessory Drive Pulley
and Fuel Feed Pump)

11 Power Take-Off (PTO) Idler 87


Gear
T2006852

12 Power Take-Off (PTO) Drive 37 Fig. 7: Timing gear arrangement


Gear for Hydraulic Pump

13 Oil Pump Drive Gear 24

14 Oil Pump Idler Gear 57

Backlash 0.05–0.17 mm (0.0017–


0.0067 in)

Axle journal for intermedi- 99.989 ± 0.011 mm (3.9


ate gear, diameter ± 0.0004 in)

Bushing for intermediate 100.037 ± 0.011 mm


gear, diameter (3.94 ± 0.0004 in)

Radial clearance for inter- 0.026–0.070 mm (0.001–


mediate gear 0.003 in)

Axial clearance for inter- 0.05–0.15 mm (0.002–


mediate gear 0.006 in)

11
Group 20 Specifications, VE D12 Specifications

Camshaft
Drive Gear

Number of bearings 7

Diameter, bearing journals, minimum:

1st, and 2nd, 7th bearing 70–0.030 mm (2.8–0.001


pin in)

T2006872
Check of camshaft setting (cold engine and 0 valve Fig. 8: Camshaft and bearings
clearance):


1 With flywheel at 6 ATDC, the intake valve for no.
1 cylinder must have opened 1.6 mm (0.06 in).

2 During this check, the timing gears must be


turned clockwise (viewed from the front) to take
up any tolerances.

Valve lift, maximum:

Intake 13.1 mm (0.5 in)

Exhaust 13.1 mm (0.5 in)

Electronic unit injectors:

Maximum stroke 15 mm (0.6 in)

Camshaft Bearings
Diameter, camshaft bearing housing:

1st bearing 73.9 ± 0.013 mm (2.9 ±


0.0005 in)

2nd–7th bearings 73.9 ± 0.013 mm (2.9 ±


0.0005 in)

12
Group 20 Specifications, VE D12 Specifications

Crankshaft
Length 1202.8 mm (47.35 in)

Crankshaft axial clear- 0.07–0.31 mm (0.0027–


ance 0.012 in)

Main bearing, radial clear- 0.044–0.121 mm (0.001–


ance 0.0048 in)

T2006958

Fig. 9: Crankshaft and bearings

Main Bearing Journals


Diameter for machining, 107.978–108.000 mm Oversize:
standard (4.251–4.252 in)
0.2 mm (axial bearing 0.1) 46.575–46.625 mm
Undersize: (1.833–1.835 in)

0.25 mm 107.728–107.75 mm 0.4 mm (axial bearing 0.2) 46.375–46.425 mm


(4.241–4.242 in) (1.825–1.827 in)

0.50 mm 107.478–107.50 mm 0.6 mm (axial bearing 0.3) 46.375–46.425 mm


(4.231–4.232 in) (1.825–1.827 in)

0.75 mm 107.228–107.25 mm Fillet radius (B) 3.75–4.00 mm (0.147–


(4.221–4.222 in) 0.157 in)

1.00 mm 106.978–107.00 mm
(4.211–4.212 in)

1.25 mm 106.728–106.75 mm
(4.201–4.202 in)

Surface finish, main bear- Ra 0.25


ing pin

Surface finish, radius Ra 0.40

Width, axial bearing pin 46.975–47.025 mm


(A) standard (1.849–1.851 in)

13
Group 20 Specifications, VE D12 Specifications

Thrust Washers (Axial Bearing)


Width (B) standard 3.140–3.210 mm (0.123–
0.126 in)

Oversize:

0.1 mm (0.004 in) 3.240–3.310 mm (0.127–


0.130 in)

0.2 mm (0.008 in) 3.340–3.410 mm (0.131–


0.134 in)

0.3 mm (0.012 in) 3.440–3.510 mm (0.135–


0.138 in)

Main Bearings
Type Replaceable

Outer diameter (C) 113.065 mm (4.45 in)

Thickness (D) standard 2.483–2.498 mm (0.097–


0.098 in)

Oversize:

0.25 mm (0.01 in) 2.608–2.623 mm (0.102–


0.103 in)

0.50 mm (0.02 in) 2.733–2.748 mm (0.107–


0.108 in)

0.75 mm (0.03 in) 2.858–2.873 mm


(0.0112–0.0113 in)

1.00 mm (0.04 in) 2.983–2.998 mm


(0.1174–0.1180 in)

1.25 mm (0.05 in) 3.108–3.123 mm


(0.1223–0.1229 in)

14
Group 20 Specifications, VE D12 Specifications

Connecting Rods
Length, center (E) 260 ± 0.05 mm (10.2 ±
0.002 in)

Marking:

Connecting rod resp. cap 1 to 6

FRONT on rod turned Forward

Connecting rod bushing 55 + 0.028 + 0.022 mm


bore (G) (2.16 + 0.001 + 0.0008 in)

Axial clearance, connecting rod, crankshaft:

Maximum 35 mm (0.013 in)

T2007005
Minimum 0.15 mm (0.006 in)
Fig. 10: Connecting rod dimensions

Connecting rod bearing, radial clearance:

Maximum 0.102 mm (0.004 in)

Minimum 0.045 mm (0.001 in)

15
Group 20 Specifications, VE D12 Specifications

Connecting Rod Bearing Journals Connecting Rod Bearings

Diameter (;) for machin- 91.978–92.000 mm Outer diameter (B) 96.85 mm (3.81 in)
ing, standard (3.621–3.622 in)
Thickness (C) standard 2.385–2.395 mm
Undersize: (0.0938–0.0942 in)

0.25 mm (0.01 in) 91.728–91.750 mm Oversize:


(3.6113–3.6122 in)
0.25 mm (1.0 in) 2.510–2.520 mm
0.50 mm (0.02 in) 91.478–91.500 mm (0.0988–0.0992 in)
(3.601–3.602 in)
0.50 mm (0.02 in) 2.635–2.645 mm (0.103–
0.75 mm (0.03 in) 91.228–91.250 mm 0.104 in)
(3.591–3.592 in)
0.75 mm (0.03 in) 2.760–2.770 mm
1.00 mm (0.04 in) 90.978–91.000 mm (0.1086–0.1090 in)
(3.581–3.582 in)
1.00 mm (0.04 in) 2.885–2.895 mm
1.25 mm (0.05 in) 90.728–90.750 mm (0.1135–0.1139 in)
(3.571–3.572 in)
1.25 mm (0.05 in) 3.010–3.020 mm
Surface finish, connecting Ra 0.25 (0.1185–0.1188 in)
rod bearing pin
Diameter, bearing seat 96.835–96.850 mm
Surface finish, radius Ra 0.4 (D) (3.812–3.8129 in)

Width (A) axial bearing 56.9–57.0 mm (2.240–


pin 2.244 in)

Fillet radius (D) (5.25–5.5) 3.75–4.00 mm (0.1476–


0.1574 in)

Flywheel
Maximum allowable axial 0.20 mm (0.0079 in)
throw (manual transmis-
sion) measuring radius
150 mm (5.9 in)

Number of teeth on fly- 153


wheel

Flywheel Housing
Maximum allowable axial 0.20 mm (0.0079 in)
throw for contact surface
against bell housing

Maximum allowable radial 0.25 mm (0.0098 in)


throw for positioning
against bell housing

16
Group 20 Specifications, VE D12 Specifications

Lubrication and Oil System


Oil
Heavy duty engine oil to API-CD/CE or CF-4 specifi-
cations. For extended oil drain intervals, the oil must
also meet Volvo Drain Specifications (VDS).

Oil Pressure
Operating speed 300–550 kPa (44–80 psi)
Idle speed, minimum 150 kPa (22 psi)

Lube Oil Pump


Type Gear driven
Number of teeth:
Drive gear 24
Intermediate gear 57
Diameter:
Hub, intermediate gear 69.99 ± 0.0095 mm (2.76 ± 0.0003 in)
Bushing, intermediate gear 70.044 ± 0.019 mm (2.76 ± 0.0007 in)
Axial clearance:
Drive gear, pump 0.110 mm (0.0043 in)
Intermediate gear 0.100 mm (0.0039 in)
Backlash 0.05–0.17 mm (0.002–0.007 in)

Oil Filters
Number ........................ 3
Full-flow filter ............... 2
Bypass filter ................. 1

17
Group 20 Specifications, VE D12 Specifications

Oil Valves
1. Reduction valve
Marking Brown
2. Overflow valve, oil cooler
Marking Green
Thermostat valve, total
40.1 mm (1.6 in)
length
3. Overflow valve, oil filter
Free length 68.8 mm (2.7 in)
With load of 13–15 Nm
40.0 mm (1.6 in)
(1.3–1.5 lb-ft)

T2006673
4. Piston cooling valve Fig. 11: Lubricating system
Marking Orange

18
Group 20 Specifications, VE D12 Specifications

Fuel System

W2001055

Fig. 12: Fuel system

Fuel Pump
Fuel pressure 300–350 kPa (43.5–50
psi)

Electronic Unit Injectors


Pre-load setting 0.75 mm (0.0295 in)

T2006849

Fig. 13: Electronic unit injector

19
Group 20 Specifications, VE D12 Specifications

Cooling System
Type Pressurized

Pressure valve opens at 75 kPa (10.9 psi)

Coolant
Antifreeze with corrosion protection meeting or ex-
ceeding ASTM D 4985 standard as a minimum.

Color Blue-green

Coolant Filter
Number 1

Anti-corrosion Additive
CAUTION
Do not mix anti-corrosion additive with concentrated
coolant or any other type of anti-corrosion fluid. Doing
so may cause damage.

Water Pump
Type Gear-driven centrifugal
pump

Thermostat
Type Plunger

 
Opening temperature, 86 C (187 F)
standard

20
Group 20 Specifications, VE D12 Specifications

Wear Tolerances
Cylinder Head
Cylinder head should be replaced if the maximum de-
viation on the flat surface (bottom face) is 0.2 mm
(0.0079 in) or greater.

Cylinder Liner
Cylinder liners (pistons and piston rings) should be re-
placed with a wear of 0.45–0.50 mm (0.018–0.019 in)
or if oil consumption is abnormally high.

Crankshaft
Maximum allowable out- 0.08 mm (0.003 in)
of-round on main and
connecting rod bearing
journals

Maximum allowable taper 0.05 mm (0.002 in)


on main and connecting
rod bearing journals

Maximum axial clearance 0.40 mm (0.015 in)


on crankshaft

Maximum throw on cen- 0.15 mm (0.0059 in)


tral journalling

Connecting Rods
Straightness, maximum 0.06 mm (0.0024 in)
deviation on a measuring
length of 100 mm (3.9 in)

Warp, maximum deviation 0.15 mm (0.0059 in)


on a measuring length of
100 mm (3.9 in)

21
Group 20 Specifications, VE D12 Specifications

Valves
Valve stem, maximum al- 0.010 mm (0.00039 in)
lowable wear on diameter

Maximum allowable clearance between valve stem


and valve guide:

Intake 0.2 mm (0.008 in)

Exhaust 0.3 mm (0.012 in)

Valve disc edge should be minimum:

Intake 1.4 mm (0.06 in)

Exhaust 1.2 mm (0.05 in)

Valve seat may be ground down as long as the dis-


tance from valve disc (new valve) to cylinder head
face does not exceed:

Intake 1.5 mm (0.06 in)

Exhaust 1.8 mm (0.07 in)

If distance exceeds specification, replace the valve


seat.

Camshaft
Maximum allowable out- 0.01 mm (0.0004 in)
of-round (bearings)

Bearings, maximum al- 0.01 mm (0.0004 in)


lowable diametrical wear

Cam profiles, allowable wear:

Intake 0.2 mm (0.008 in)

Exhaust 0.2 mm (0.008 in)

Engine brake (VEB) 0.1 mm (0.004 in)

Unit injectors 0.1 mm (0.004 in)

22
Group 20 Specifications, VE D12 Specifications

Tightening Torques
Component Nm lb-ft

Main bearing 150 ± 20 111 ± 14


cap bolts Step 1

 
Main bearing Turn an additional 120 ± 5
cap bolts Step 2

Connecting rod 252 ± 12 186 ± 9


bearing cap
bolts

A/C compressor 48 ± 8 35 ± 6
bolts
24 ± 3
Fuel feed pump 33 ± 4
bolts M8
W2000700

48 ± 8
Fuel feed pump 35 ± 6
bolts M10

Starter mount- 85 ± 15 63 ± 11
ing bolts
35 ± 6
Power steering 48 ± 8
pump bolts

ECU mounting 33 ± 4 24 ± 3
bolts
24 ± 3
Timing gear 33 ± 4
plate bolts M8
35 ± 6
Timing gear 48 ± 8
cover bolts M10

Timing gear 85 ± 15 63 ± 11
cover bolts M12

Timing gear 140 ± 12 103 ± 10


cover bolts M14 W2000701

Fig. 14: Torque sequences for timing gears

23
Group 20 Specifications, VE D12 Specifications

Component Nm lb-ft
Oil pan bolts 24 ± 4 18 ± 3
Drain plug, oil pan 60 ± 15 44 ± 11
Oil pump bracket bolts 24 ± 4 18 ± 3

Note: First tighten the bolts marked X, then tighten the


remaining bolts.

T2006802

Fig. 15: Tightening sequence for oil pan bolts

lb- ft
Component Nm

Cylinder head 60 ± 10 44 ± 7
bolts, Step 1

 
Cylinder head Turn an additional 90 ± 5
bolts, Step 2

 
Cylinder head Turn an additional 90 ± 5
bolts, Step 3

T2007004

Fig. 16: Tightening sequence for cylinder head bolts


24
Group 20 Specifications, VE D12 Specifications

Nm
Component lb-ft

Flywheel hous- 140 ± 14 103 ± 10


ing bolts
63 ± 4
Flywheel bolts, 85 ± 5
Step 1

 
Flywheel bolts, Turn an additional 30 ± 3
Step 2

Retainer bolt, unit injector with new copper sleeve


T2006973

First tightening, 20 ± 5 15 ± 4 Fig. 17: Tightening sequence for flywheel bolts


Step 1

 
First tightening, Turn an additional 180 ± 5
Step 2

Note: Loosen the retainer bolt for the unit injector prior
to the second tightening

Second tighten- 20 ± 5 15 ± 4
ing, Step 1

 
Second tighten- Turn an additional 60 ± 5
ing, Step 2

Retainer bolt, unit injector with old copper washer


20 ± 5
Step 1 15 ± 4

 
Step 2 Turn an additional 60 ± 5

25
Group 20 Specifications, VE D12 Specifications

Component Nm lb-ft
30 ± 3
Valve cover nuts 22 ± 2

M14 engine 140 ± 25 103 ± 18


mounting bolt

T2007003

Fig. 18: Tightening sequence for valve cover bolts

26
Group 20 Specifications, VE D12 Specifications

Component Nm lb-ft

Exhaust mani- 48 ± 8 35 ± 6
fold bolts
24 ± 3
Intake manifold 33 ± 4
bolts
37 ± 4
Vibration 50 ± 5
damper bolts

Piston cooling 24 ± 4 18 ± 3
nozzle bolt

Cleaning plugs, 60 ± 10 44 ± 7
cylinder head
(M38 x 1.5)
35 ± 6
Valve cover stud 48 ± 8
(Loctite)

Oil cooler 27 ± 4 20 ± 3
mounting bolts
27 ± 4
Oil strainer 20 ± 3
mounting bolts
(in pump)

Valve adjust- 38 ± 4 28 ± 3
ment locknut

Nut, unit injector 1.4 1


electrical con-
nection

T2007002

Fig. 19: Tightening sequence for exhaust manifold bolts

27
Group 20 Specifications, VE D12 Specifications

When reinstalling a rocker arm shaft that has been loos-


ened or removed, torque only the bolts holding the shaft,
according to the diagram.

Note: Loosen the marked bolts in step 8 before pro-


ceeding to steps 9 and 10.

W2000693

Fig. 20: Torque values and procedure for camshaft hous-


ing bolts

28
29
Volvo Trucks North America, Inc.
P.O. Box 26115, Greensboro, NC 27402-6115
Volvo Trucks Canada, Ltd.
6490 Vipond Drive, Mississauga, Ontario L5T 1W8
http://www.volvotrucks.volvo.com

V776-200-820SM (2000) © Volvo Trucks North America, Inc., 95

You might also like