Question Paper Mos r15 Jntua
Question Paper Mos r15 Jntua
Question Paper Mos r15 Jntua
20 cm 25 cm
22 cm
OR
3 A steel tube of 30 mm external diameter and 20 mm internal diameter encloses a copper rod of
15 mm diameter to which it is rigidly joined at each end. If, at a temperature of 10 there is no
longitudinal stress, calculate the stresses in the rod and tube when the temperature is raised to
200 . Take E for steel and copper as 2.1 x 105 N/mm2 and 1 x 105 N/mm2 respectively. The value
of co-efficient of linear expansion for steel and copper is given as 11 x 10-6 per and 18 x 10-6 per
respectively.
UNIT - II
4 Draw the S.F. and B.M. diagrams of a simply supported beam of length 7 m carrying uniformly
distributed loads as shown in figure below.
10 kN/m 5 kN/m
C D
A B
3m 2m 2m
RA RB
OR
5 Draw the S.F. and B.M. diagrams for the overhanging beam carrying uniformly distributed load of 2
kN/m over the entire length and a point load of 2 kN as shown in figure. Locate the point of
contraflexure. 2 kN/m 2 kN
A
B C
4m 2m
RA RB
Contd. in page 2
Page 1 of 2
Code: 15A01308
R15
UNIT - III
6 A timber beam of rectangular section is to support a load of 20 kN uniformly distributed over a span
of 3.6 m when beam is simply supported. If the depth of section is to be twice the breadth, and the
stress in the timber is not to exceed 7 N/mm2, find the dimensions of the cross-section. How would
you modify the cross-section of the beam, if it carries a concentrated load of 20 kN placed at the
centre with the same ratio of breadth to depth.
OR
7 The shear force acting on a section of a beam is 50 kN. The section of the beam is of T-shaped of
dimensions 100 mm x 100 mm x 20 mm as shown in figure. The moment of inertia about the
horizontal neutral axis is 314.221 x 104 mm4. Calculate the shear stress at the neutral axis and at
the junction of the web and the flange.
Y
100 mm
20 mm 1
100 mm
80 mm
N A
2
20 mm
Y
UNIT - IV
8 Determine the diameter of a solid shaft which will transmit 300 kW at 250 r.p.m. The maximum
shear stress should not exceed 30 N/mm2 and twist should not be more than in a shaft length of
2 m. Take modulus of rigidity = 1 x 105 N/mm2.
OR
9 A beam of length 5 m and of uniform rectangular section is supported at its ends and carries
uniformly distributed load over the entire length. Calculate the depth of the section if the maximum
permissible bending stress is 8 N/mm2 and central deflection is not to exceed 10 mm. Take the
value of E = 1.2 x 104 N/mm2.
UNIT - V
10 A cylindrical vessel is 1.5 m diameter and 4 m long is closed at ends by rigid plates. It is subjected
to an internal pressure of 3 N/mm2. If the maximum principal stress is not to exceed 150 N/mm2,
find the thickness of the shell. Assume E = 2 x 105 N/mm2 and Poisson’s ratio = 0.25. Find the
changes in diameter, length and volume of the shell.
OR
11 A steel cylinder of 300 mm external diameter is to be shrunk to another steel cylinder of 150 mm
internal diameter. After shrinking the diameter at the junction is 250 mm and radial pressure at the
common junction is 28 N/mm2. Find the original difference in radii at the junction.
Take E = 2 x 105 N/mm2.
*****
Page 2 of 2