0% found this document useful (0 votes)
22 views25 pages

Disassembly Procedures: AG-AC90P/PX/PJ/AN/EJ/EN/MC

Download as pdf or txt
Download as pdf or txt
Download as pdf or txt
You are on page 1/ 25

DISASSEMBLY PROCEDURES

Model No. : AG-AC90P/PX/PJ/AN/EJ/EN/MC

CONTENTS
1. Disassembly Flowchart ............................................................................................................... DIS-1
2. Removal of LENS HOOD Unit..................................................................................................... DIS-2
3. Removal of LENS MASK and FRONT CASE Unit...................................................................... DIS-3
4. Removal of SIDE CASE L Unit.................................................................................................... DIS-4
5. Removal of GRIP Unit ................................................................................................................. DIS-5
6. Removal of REMOTE JACK Unit ................................................................................................ DIS-6
7. Removal of WIRED REMOTE P.C.B. ......................................................................................... DIS-6
8. Removal of MAIN P.C.B.............................................................................................................. DIS-7
9. Removal of REAR CASE Unit ..................................................................................................... DIS-8
10. Removal of BATTERY CATCHER P.C.B.................................................................................. DIS-9
11. Removal of SD HOLDER P.C.B................................................................................................ DIS-9
12. Removal of USB AV P.C.B. and HDMI FPC ............................................................................. DIS-10
13. Removal of MF RING Unit......................................................................................................... DIS-11
14. Removal of LENS RELAY P.C.B. ............................................................................................. DIS-12
15. Removal of FAN MOTOR.......................................................................................................... DIS-13
16. Removal of CAMERA LENS Unit.............................................................................................. DIS-14
17. Removal of HANDLE CASE L Unit ........................................................................................... DIS-15
18. Removal of SIDE CASE R Unit ................................................................................................. DIS-16
19. Removal of SIDE R OP P.C.B................................................................................................... DIS-17
20. Removal of EVF Unit................................................................................................................. DIS-18
21. Removal of HANDLE T Unit ...................................................................................................... DIS-19
22. Removal of MIC Unit ................................................................................................................. DIS-20
23. Removal of XLR P.C.B.............................................................................................................. DIS-20
24. Removal of LED P.C.B.............................................................................................................. DIS-21
25. Removal of HANDLE OP P.C.B. ............................................................................................... DIS-21
26. Removal of HANDLE B Unit...................................................................................................... DIS-22
27. Removal of LCD PANEL Unit.................................................................................................... DIS-23
1. Disassembly Flowchart

NOTE: Please put on your hand glove, when you operated disassemble and assemble.

21. HANDLE T Unit

23. XLR P.C.B.

22. MIC Unit

24. LED P.C.B.

2. LENS HOOD Unit 25. HANDLE OP P.C.B.

3. LENS MASK & FRONT CASE Unit

4. SIDE CASE L Unit 5. GRIP Unit

6. REMOTE JACK Unit 7. WIRED REMOTE P.C.B. 17. HANDLE CASE L Unit

8. MAIN P.C.B. 19. SIDE R OP P.C.B. 18. SIDE CASE R Unit

9. REAR CASE Unit 10. BATT CATCHER P.C.B.

11. SD HOLDER P.C.B.

20. EVF Unit

26. HANDLE B Unit

12. USB AV P.C.B. & HDMI FPC 27. LCD PANEL Unit

13. MF RING Unit

14. LENS RELAY P.C.B. 15. FAN MOTOR

16. CAMERA LENS Unit

DIS-1
2. Removal of LENS HOOD Unit

1. Unscrew a screw (A) as shown in figure 2-1 and remove the LENS HOOD Unit.

LENS HOOD Unit

SCREW (A)

Figure 2-1

DIS-2
3. Removal of LENS MASK and FRONT CASE Unit

1. Unscrew the 3 screws (A) as shown in figure 3-1 and remove the LENS MASK Unit.
2. Unscrew the 2 screws (B) as shown in figure 3-1.
3. Release the hook form the claw as shown in figure 3-1 and remove the FRONT CASE Unit.

SCREW (B)
SCREW (A)

CRAW

HOOK

SCREW (A) & (B)


FRONT CASE Unit

LENS MASK Unit

Figure 3-1

DIS-3
4. Removal of SIDE CASE L Unit

1. Unscrew the 7 screws (A), a screw (B) and a screw (C) as shown in figure 4-1.
2. Disconnect the connector (A) and (B) as shown in figure 4-1, and remove the SIDE CASE L Unit.

SCREW (B) SCREW (A)

CONNECTOR (A) CONNECTOR (B)


SCREW (A)

SCREW (C)

SIDE CASE L Unit

SCREW (C) SCREW (A) SCREW (B)

Figure 4-1

DIS-4
5. Removal of GRIP Unit

1. Remove the GRIP BELT as shown in figure 5-1.

1 Open GRIP BELT

Open

SIDE CASE L Unit

2 3

Figure 5-1

2. Unscrew the 9 screws (A) as shown in figure 5-1 and remove the GRIP Unit.
NOTE: Unhook the 2 places of the Locking Tab as shown in figure 5-1.

Locking Tab

GRIP Unit

SCREW (A)

Figure 5-1

DIS-5
6. Removal of REMOTE JACK Unit

1. Disconnect the connector (A) and (B) as shown in figure 6-1.


2. Unscrew the 2 screws (A) as shown in figure 6-1 and remove the REMOTE JACK Unit.

SCREW (A)

SCREW (A)
REMOTE JACK Unit

CONNECTOR (A)

CONNECTOR (B)

Figure 6-1

7. Removal of WIRED REMOTE P.C.B.

1. Unscrew the 2 screws (A) and Nut (A) as shown in figure 7-1, and remove the WIRED REMOTE P.C.B. from
the REMOTE JACK FRAME.

SCREW (A)

NUT (A)
SCREW (A)

WIRED REMOTE P.C.B.

REMOTE JACK FRAME

Figure 7-1

DIS-6
8. Removal of MAIN P.C.B.

1. Disconnect the connector (A), (B), (C), (D), (E), (F), (G), (H), (I), (J) and (K) as shown in figure 8-1.
2. Unscrew the 4 screws (A) as shown in figure 8-1.
3. Disconnect the connector (L), (M) and (N) as shown in figure 8-1, and remove the MAIN P.C.B..

CONNECTOR (C) CONNECTOR (D) CONNECTOR (E) CONNECTOR (F)

CONNECTOR (B)
CONNECTOR (G)

CONNECTOR (H)
CONNECTOR (A)

SCREW (A) CONNECTOR (I)

CONNECTOR (K) CONNECTOR (J)

CONNECTOR (N)
CONNECTOR (L)
CONNECTOR (M)

MAIN P.C.B.

Figure 8-1

DIS-7
9. Removal of REAR CASE Unit

1. Disconnect the flexible cable (A) as shown in figure 9-1.


NOTE: If the REAR CASE Unit is removed without disconnect the flexible cable (A), that may cause flexible cable
(A) to be damaged.
2. Unscrew the 7 screws (A) as shown in figure 9-1.
3. Unhook the Locking Tab as shown in figure 9-1, and remove the REAR CASE Unit.

SCREW (A) Flexible cable (A)


(It connected to connector on SD HOLDER P.C.B..)

SCREW (A)

Locking Tab

REAR CASE Unit

SCREW (A)

SCREW (A)

Figure 9-1

< Note for assemble and disassemble >


Be careful not to be damaged to the cable as shown in figure 9-2.

This portion

Figure 9-2

DIS-8
10. Removal of BATTERY CATCHER P.C.B.

1. Unhook the 2 places of Locking Tab as shown in figure 10-1, and remove the BATTERY CATCHER P.C.B..

BATTERY CATCHER P.C.B.

Locking Tab Locking Tab

Please insert the small screw driver at this portion and lift up
the BATTERY CATCHER P.C.B. for removing.

REAR CASE Unit

Figure 10-1

11. Removal of SD HOLDER P.C.B.

1. Unscrew the 2 screws (A) as shown in figure 11-1 and remove the SD HOLDER P.C.B..

SCREW (A)

SCREW (A)

SD HOLDER P.C.B.

REAR CASE Unit

Figure 11-1

DIS-9
12. Removal of USB AV P.C.B. and HDMI FPC

1. Unscrew a screw (A) as shown in figure 12-1 and remove the REAR JACK FRAME (with USB AV P.C.B. and
HDMI FPC).
2. Unscrew the 2 screws (B) as shown in figure 12-1 and remove the USB AV P.C.B. from the REAR JACK
FRAME.

SCREW (A) SCREW (B)

USB AV P.C.B.

SCREW (A)

SCREW (B)

Figure 12-1

3. Unscrew the 2 screws (C) as shown in figure 12-2 and remove the HDMI FPC from the REAR JACK FRAME.

SCREW (C) HDMI FPC

SCREW (C)

REAR JACK FRAME

Figure 12-2

DIS-10
13. Removal of MF RING Unit

1. Unscrew the 4 screws (A) as shown in figure 13-1 and remove the MF RING Unit (with CAMERA LENS Unit
etc.) from MAIN FRAME Unit.

SCREW (A)

SCREW (A)

MF RING Unit (with CAMERA LENS Unit etc.)

MAIN FRAME Unit

Figure 13-1

DIS-11
2. Unscrew the 4 screws (B) as shown in figure 13-2 and remove the MF RING Unit from CAMERA LENS Unit
(with FAN MOTOR etc.).

SCREW (B)

MF RING Unit

CAMERA LENS Unit (with FAN MOTOR etc.)

Figure 13-2

14. Removal of LENS RELAY P.C.B.

1. Disconnect the connector (A) as shown in figure 14-1


2. Unscrew the 2 screws (A) and remove the LENS RELAY P.C.B..

CONNECTOR (A)
SCREW (A)
LENS RELAY P.C.B.

SCREW (A)

Figure 14-1

DIS-12
15. Removal of FAN MOTOR

1. Unscrew the 2 screws (A) as shown in figure 15-1.


2. Unhook the 2 places of Locking Tab (A) and (B) as shown in figure 15-1 and remove the FAN COVER (with
FAN MOTOR and FAN DUMPER RUBBER).
NOTE: Unhook the Locking Tab (A) first.

Locking Tab (B)

SCREW (A)

Locking Tab (A)

Figure 15-1

3. Remove the FAN MOTOR from FAM DAMPER RUBBER and FAN COVER as shown in figure 15-2.

FAN COVER (with FAN MOTOR and FAN DUMPER RUBBER) FAM DAMPER RUBBER

FAM MOTOR

FAM COVER

Figure 15-2

DIS-13
16. Removal of CAMERA LENS Unit

1. Unscrew the 2 screws (A) and a screw (B) as shown in figure 16-1.
2. Remove the CAMERA LENS Unit (with LENS ANGLE Unit etc.) from LENS FRAME Unit as shown in figure
16-1.

SCREW (A)
SCREW (A)

CAMERA LENS Unit (with LENS ANGLE Unit etc.)

SCREW (B)

LENS FRAME Unit

Figure 16-1

3. Release the hole of LENS ANGLE Unit from 2 places of Tab of CAMERA LENS Unit (with MOS RELAY cable)
as shown in figure 16-2.
4. Remove the LENS ANGLE Unit from CAMERA LENS Unit (with MOS RELAY cable).

Hole LENS ANGLE Unit Tab CAMERA LENS Unit

MOS RELAY cable

Figure 16-2

DIS-14
17. Removal of HANDLE CASE L Unit

1. Unscrew the 2 screws (A), a screw (B) and a screw (C) as shown in figure 17-1.
2. Unhook the 2 places of the Locking Tab as shown in figure 17-1 and remove the HANDLE CASE L Unit.

SCREW (A) SCREW (B) SCREW (C)

SCREW (A)

SCREW (B)

SCREW (C)

HANDLE CASE L Unit

Locking tab

Figure 17-1

DIS-15
18. Removal of SIDE CASE R Unit

1. Unscrew the 3 screws (A), a screw (B) and 2 screws (C) as shown in figure 18-1.

SCREW (A)

SCREW (C)

SCREW (B)

SCREW (A) SCREW (B) SCREW (C)

Locking tab (B)

Figure 18-1

2. Unhook the 2 places of the Locking Tab (A) as shown in figure 18-2.
3. Unhook a place of the Locking Tab (B) as shown in figure 18-1.
4. Disconnect the connector (A) and (B) as shown in figure 18-2, and remove the SIDE CASE R Unit.

Locking tab (A)

CONNECTOR (C)

CONNECTOR (B) CONNECTOR (A)

Figure 18-2

< Note for assembly >


As shown in figure 18-2, the flexible cable connected with connector (B) should go under the cable connected
with connector (C).

DIS-16
19. Removal of SIDE R OP P.C.B.

1. Unscrew the 11 screws (A) as shown in figure 19-1 and remove the SIDE R OP P.C.B..

SCREW (A)

SIDE R OP P.C.B.

Figure 19-1

DIS-17
20. Removal of EVF Unit

1. Disconnect the connector (A) as shown in figure 20-1.


2. Unhook the 4 places of Locking Tab as shown in figure 20-1 and remove the EVF GUIDE.
3. Unscrew a screw (A) as shown in figure 20-1 and remove the EVF Unit.

SCREW (A) EVF Unit

Locking Tab

EVF GUIDE SCREW (A)

CONNECTOR (A)

Figure 20-1

DIS-18
21. Removal of HANDLE T Unit

1. Unscrew the 4 screws (A), 4 screws (B) and 2 screws (C) as shown in figure 21-1.
2. Disconnect the connector (A) as shown in figure 21-1, and remove the HANDLE T Unit.
NOTE: Unhook the 2 places of the Locking Tab as shown in figure 21-1

SCREW (B)
CONNECTOR (A)

SCREW (A)

SCREW (A)

HANDLE T Unit
SCREW (C)

SCREW (C)

SCREW (A) SCREW (B) SCREW (C)

Locking Tab

Figure 21-1

DIS-19
22. Removal of MIC Unit

1. Disconnect a connector (A) as shown in figure 22-1 and remove the MIC Unit.

MIC Unit

CONNECTOR (A)

Figure 22-1

23. Removal of XLR P.C.B.

1. Unscrew the 4 screws (A) and a screw (B) as shown in figure 23-1.
2. Disconnect the connector (A) as shown in figure 23-1 and remove the XLR P.C.B..

SCREW (A) SCREW (B) SCREW (A)


XLR P.C.B.

SCREW (B)

CONNECTOR (A)

Figure 23-1

NOTE: Pull out the LCD PANEL Unit as shown in figure before remove the XLR P.C.B..

LCD PANEL Unit

Figure 23-2

DIS-20
24. Removal of LED P.C.B.

1. Disconnect a connector (A) as shown in figure 24-1 and remove the LED P.C.B..

CONNECTOR (A)
LED P.C.B.

Figure 24-1

25. Removal of HANDLE OP P.C.B.

1. Disconnect the connector (A), (B), (C), (D) and (E) as shown in figure 25-1.
2. Unscrew the 2 screws (A) and a screw (B) as shown in figure 25-1.
3. Disconnect the connector (F) and (G) as shown in figure 25-1 and remove the HANDLE OP P.C.B..

SCREW (A) SCREW (B)

CONNECTOR (C)
CONNECTOR (B)

CONNECTOR (A)

CONNECTOR (G)

CONNECTOR (F)

HANDLE OP P.C.B. CONNECTOR (E)

CONNECTOR (D)

Figure 25-1

DIS-21
26. Removal of HANDLE B Unit

1. Unscrew the 2 screws (A) as shown in figure 26-1 and remove the HANDLE B Unit (without HANDLE OP
P.C.B.).

SCREW (A)

SCREW (A)

HANDLE B Unit (without HANDLE OP P.C.B.)

Figure 26-1

DIS-22
27. Removal of LCD PANEL Unit

1. Unscrew the 4 screws (A), (B), (C) and (D) as shown in figure 27-1.

SCREW (C) SCREW (D)

SCREW (A)

SCREW (B)

Figure 27-1

2. Unhook the 6 places of Locking Tab as shown in figure 27-2 and remove the LCD CASE TOP from LCD
PANEL Unit.
3. Disconnect the connector (A) and (B) as shown in figure 27-2

LCD CASE TOP LCD CASE TOP

Locking Tab

CONNECTOR (A)
CONNECTOR (B)

LCD PANEL Unit LCD PANEL Unit

Figure 27-2

DIS-23
< Note for assembly >
1. Confirm the magnet is installed to LCD CASE BACK correctly as shown in figure 27-3.

marking

LCD CASE BACK


Magnet

Figure 27-3

2. Tighten the screws (A) and (C) as shown in figure 27-1 temporarily before connect the connector (A) and (B)
as shown in figure 27-4 not to move the LCD PANEL Unit. And unscrew the screws (A) and (C) as shown in
figure 27-1 after connected the connector (A) and (B) as shown in figure 27-4.

CONNECTOR (B) CONNECTOR (A)

Figure 27-4

DIS-24

You might also like