Scribd
Upload
201 views4 pages

Combination Meter LS430

The document provides instructions for overhauling a combination meter assembly. It describes removing components like the glass, plates, cover, and circuit board. Tape is recommended for prying components to avoid damage. Static electricity must be discharged before handling parts. Reinstallation follows the removal process in reverse order. Care is needed as some parts get extremely hot immediately after turning off the ignition.

Uploaded by

Adam Borowski
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
201 views4 pages

Combination Meter LS430

The document provides instructions for overhauling a combination meter assembly. It describes removing components like the glass, plates, cover, and circuit board. Tape is recommended for prying components to avoid damage. Static electricity must be discharged before handling parts. Reinstallation follows the removal process in reverse order. Care is needed as some parts get extremely hot immediately after turning off the ignition.

Uploaded by

Adam Borowski
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

71−21

INSTRUMENT PANEL/METER − COMBINATION METER ASSY

COMBINATION METER ASSY


710L3−01

OVERHAUL
HINT:
S COMPONENTS: SEE PAGE 71−1
S Installation is in the reverse order of removal.
NOTICE:
S There should be no oil or fingerprints on the combination meter glass and combination meter
ECU.
S Wipe off any oil or fingerprints from the combination meter glass and meter display panel with
a soft cloth.
S Be careful of static electricity when handling the meter display panel and combination meter
ECU.
S When disassembling the combination meter assy, eliminate static electricity by touching the
vehicle body to prevent the components from being damaged.
CAUTION:
Do not touch the circuit. Even after the ignition switch is turned off, the meter display panel condens-
er will still be charged.
1. REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER LOWER (SEE PAGE 71−6)
2. REMOVE INSTRUMENT CLUSTER FINISH PANEL END (SEE PAGE 71−6)
3. REMOVE INSTRUMENT CLUSTER FINISH PANEL (SEE PAGE 71−6)
4. REMOVE COMBINATION METER ASSY (SEE PAGE 71−6)

5. REMOVE COMBINATION METER GLASS


(a) Using a screwdriver, disengage the 9 claws and remove
the combination meter glass.
HINT:
Tape up the screwdriver tip before use.

9 Claws
B75413

Author: Date: 4860


71−22
INSTRUMENT PANEL/METER − COMBINATION METER ASSY

6. REMOVE COMBINATION METER PLATE NO.1


(a) Remove the screw.
(b) Using a screwdriver, disengage the 6 claws and remove
the combination meter plate No.1.
HINT:
Tape up the screwdriver tip before use.

6 Claws B75414

A 7. REMOVE COMBINATION METER COVER NO.1


(a) Remove the 6 screws.
(b) Using a screwdriver, disengage the 3 claws and remove
the combination meter cover No.1.
HINT:
Tape up the screwdriver tip before use.
CAUTION:
A is extremely hot immediately after the ignition switch is
turned off.

3 Claws
B75415

8. REMOVE METER DISPLAY PANEL


(a) Remove the 8 screws.
(b) Remove the meter display panel.

B75416

Author: Date: 4861


71−23
INSTRUMENT PANEL/METER − COMBINATION METER ASSY

9. REMOVE COMBINATION METER ECU


Claw
(a) Remove the 4 screws.
(b) Disconnect the connectors.
(c) Using a screwdriver, disengage the claw and remove the
combination meter ECU.
HINT:
Tape up the screwdriver tip before use.

B75417

(d) Using a screwdriver, disengage the combination meter


ECU (speed meter assy).
HINT:
Tape up the screwdriver tip before use.

B75418

(e) Remove the combination meter ECU (speed meter assy).

B75419

Author: Date: 4862


71−24
INSTRUMENT PANEL/METER − COMBINATION METER ASSY

10. REMOVE ECU METER CIRCUIT PLATE


5 Claws
(a) Using a screwdriver, disengage the 5 claws and remove
the ECU meter circuit plate from the combination meter
case No.1.
HINT:
Tape up the screwdriver tip before use.

B75420

11. INSTALL COMBINATION METER ECU


(a) Install the pins and the combination meter ECU (speed
meter assy).
CAUTION:
S Install the pins securely.
S Hold a hand over the panel meter during installation.

B75419

(b) Engage the claw and install the combination meter ECU
Claw
with 4 screws.
(c) Connect the connectors.

B75417

Author: Date: 4863

You might also like