ESO 201A: Thermodynamics

CHAPTER 3: PROPERTIES OF PURE

SUBSTANCES

Instructor: Dr. Ashoke De

Department of Aerospace Engineering
http://home.iitk.ac.in/~ashoke
Email: [email protected]
 Objectives
 Introduce the concept of a pure substance.
 Discuss the physics of phase-change processes.
 Illustrate the P-v, T-v, and P-T property diagrams and P-v-T
surfaces of pure substances.
 Demonstrate the procedures for determining thermodynamic
properties of pure substances from tables of property data.
 Describe the hypothetical substance “ideal gas” and the ideal-
gas equation of state.
 Apply the ideal-gas equation of state in the solution of typical
problems.
 Introduce the compressibility factor, which accounts for the
deviation of real gases from ideal-gas behavior.
 Present some of the best-known equations of state.
2
 PURE SUBSTANCE
 Pure substance: A substance that has a fixed chemical
composition throughout.
 Air is a mixture of several gases, but it is considered to be a
pure substance.

3
PHASES OF A PURE The molecules
SUBSTANCE in a solid are
kept at their
positions by the
large springlike
inter-molecular
forces.

4
PHASE-CHANGE PROCESSES
OF PURE SUBSTANCES
Compressed liquid (subcooled Saturated liquid: A liquid that
liquid): A substance that it is not is about to vaporize
about to vaporize

5
o Saturated vapor: A vapor that is about to condense.
o Saturated liquid–vapor mixture: The state at which the liquid and
vapor phases coexist in equilibrium.
o Superheated vapor: A vapor that is not about to condense (i.e., not a
saturated vapor).

At 1 atm pressure, the As more heat is

As more heat is transferred, temperature remains transferred, the
part of the saturated liquid constant at 100°C until the temperature of the
vaporizes (saturated liquid– last drop of liquid is vaporized vapor starts to rise
vapor mixture). (saturated vapor). (superheated vapor).
6
 T-v diagram for the
heating process of
water at constant
pressure.

If the entire process between state 1 and 5 is reversed by cooling the

water while maintaining the pressure at the same value, the water will go
back to state 1, retracing the same path, and in so doing, the amount of
heat released will exactly match the amount of heat added during the
heating process.
7
Saturation Temperature and Saturation Pressure
The temperature at which water starts boiling depends on the pressure; therefore,
if the pressure is fixed, so is the boiling temperature.
Water boils at 100C at 1 atm pressure.
Saturation temperature Tsat: The temperature at
which a pure substance changes phase at a given
pressure.
Saturation pressure Psat: The pressure at which a
pure substance changes phase at a given
temperature.

The liquid–vapor
saturation curve
of a pure
substance
(numerical
values are for
water). 8
 Latent heat: The amount of energy
absorbed or released during a phase-
change process.
 Latent heat of fusion: The amount of
energy absorbed during melting. It is
equivalent to the amount of energy
released during freezing.
 Latent heat of vaporization: The amount
of energy absorbed during vaporization
and it is equivalent to the energy released
during condensation.
 The magnitudes of the latent heats
depend on the temperature or pressure at
which the phase change occurs.
 At 1 atm pressure, the latent heat of
fusion of water is 333.7 kJ/kg and the
latent heat of vaporization is 2256.5 kJ/kg.
 The atmospheric pressure, and thus the
boiling temperature of water, decreases
with elevation.
9
Some Consequences of
Tsat and Psat Dependence
The variation of
the temperature
of fruits and
vegetables with
pressure during
vacuum cooling
from 25°C to 0°C.

In 1775, ice was made

by evacuating the air
space in a water tank.
10
 PROPERTY DIAGRAMS FOR
PHASE-CHANGE PROCESSES
The variations of properties during phase-change processes are best studied
and understood with the help of property diagrams such as the T-v, P-v, and P-T
diagrams for pure substances.

T-v diagram of
constant-pressure
phase-change
processes of a pure
substance at various
pressures
(numerical values
are for water). 11
 saturated liquid line
 saturated vapor line
 compressed liquid region
 superheated vapor region
 saturated liquid–vapor
mixture region (wet region)

At supercritical pressures Critical point: The point

(P > Pcr), there is no at which the saturated
distinct phase-change liquid and saturated vapor
(boiling) process. states are identical. 12
Extending the For water,
Diagrams to Include Ttp = 0.01°C
Ptp = 0.6117 kPa
the Solid Phase
At triple-point pressure
and temperature, a
substance exists in three
phases in equilibrium.

13
 Phase Diagram
Sublimation:
Passing from the
solid phase directly
into the vapor phase.

At low pressures
(below the triple-point
value), solids
evaporate without
melting first
(sublimation).
P-T diagram of pure substances.
14
The P-v-T surfaces present a great deal of information at once, but in a
thermodynamic analysis it is more convenient to work with two-dimensional
diagrams, such as the P-v and T-v diagrams.

15
 PROPERTY TABLES
• For most substances, the relationships among thermodynamic properties are too
complex to be expressed by simple equations.
• Therefore, properties are frequently presented in the form of tables.
• Some thermodynamic properties can be measured easily, but others cannot and
are calculated by using the relations between them and measurable properties.
• The results of these measurements and calculations are presented in tables in a
convenient format.
Enthalpy—A Combination Property

The
combination
u + Pv is
frequently
encountered
in the analysis
of control
volumes. 16
Saturated Liquid
and Saturated
Vapor States

A partial list of Table A–4.

• Table A–4: Saturation properties of

water under temperature.
• Table A–5: Saturation properties of
water under pressure.

Enthalpy of vaporization, hfg (Latent

heat of vaporization): The amount of
energy needed to vaporize a unit mass
of saturated liquid at a given
temperature or pressure.
17
Examples: Saturated
liquid and saturated vapor
states of water on T-v and
P-v diagrams.

18
Saturated Liquid–Vapor Mixture
Quality, x : The ratio of the mass of vapor to the total mass of the mixture.
Quality is between 0 and 1 0: sat. liquid, 1: sat. vapor.
The properties of the saturated liquid are the same whether it exists alone or in
a mixture with saturated vapor.
Temperature and
pressure are dependent
properties for a mixture.

The relative
amounts of
liquid and
vapor phases
in a saturated
mixture are A two-phase system can be
specified by treated as a homogeneous
the quality x. mixture for convenience. 19
y v, u, or h.

20
Examples: Saturated liquid-vapor
mixture states on T-v and P-v diagrams.

21
In the region to the right of the Superheated Vapor
saturated vapor line and at
temperatures above the critical Compared to saturated vapor,
point temperature, a substance superheated vapor is characterized by
exists as superheated vapor.
In this region, temperature and
pressure are independent
properties.

At a specified
P, superheated
vapor exists at
a higher h than
the saturated
vapor.

A partial
listing of
Table A–6. 22
The compressed liquid properties Compressed Liquid
depend on temperature much more Compressed liquid is characterized by
strongly than they do on pressure.
y  v, u, or h

A more accurate relation for h

A compressed liquid
may be approximated
as a saturated liquid at
the given temperature.

23
24
 Reference State and Reference Values
 The values of u, h, and s cannot be measured directly, and they are
calculated from measurable properties using the relations between
properties.
 However, those relations give the changes in properties, not the values of
properties at specified states.
 Therefore, we need to choose a convenient reference state and assign a
value of zero for a convenient property or properties at that state.
 The reference state for water is 0.01°C and for R-134a is -40°C in tables.
 Some properties may have negative values as a result of the reference state
chosen.
 Sometimes different tables list different values for some properties at the
same state as a result of using a different reference state.
 However, In thermodynamics we are concerned with the changes in
properties, and the reference state chosen is of no consequence in
calculations.

25
 THE IDEAL-GAS EQUATION OF STATE
o Equation of state: Any equation that relates the pressure, temperature,
and specific volume of a substance.
o The simplest and best-known equation of state for substances in the gas
phase is the ideal-gas equation of state. This equation predicts the P-v-T
behavior of a gas quite accurately within some properly selected region.
Ideal gas equation
of state

R: gas constant
M: molar mass (kg/kmol)
Ru: universal gas constant

Different substances have different

gas constants.
26
Mass = Molar mass  Mole number

Ideal gas
equation at two
states for a fixed
mass

Various expressions
of ideal gas equation

Real gases behave as an ideal

gas at low densities (i.e., low
pressure, high temperature).
27
 • At pressures below 10 kPa, water
Is Water Vapor an Ideal Gas? vapor can be treated as an ideal
gas, regardless of its temperature,
with negligible error (less than 0.1
percent).
• At higher pressures, however, the
ideal gas assumption yields
unacceptable errors, particularly in
the vicinity of the critical point and
the saturated vapor line.
• In air-conditioning applications, the
water vapor in the air can be
treated as an ideal gas.
• In steam power plant applications,
however, the pressures involved
are usually very high; therefore,
ideal-gas relations should not be
used.

28
COMPRESSIBILITY FACTOR—A MEASURE
OF DEVIATION FROM IDEAL-GAS BEHAVIOR
Compressibility factor Z The farther away Z is from unity, the more the
A factor that accounts for gas deviates from ideal-gas behavior.
the deviation of real gases Gases behave as an ideal gas at low densities
from ideal-gas behavior at (i.e., low pressure, high temperature).
a given temperature and Question: What is the criteria for low pressure
pressure. and high temperature?
Answer: The pressure or temperature of a gas
is high or low relative to its critical temperature
or pressure.

29
 Reduced Reduced
pressure temperature
Pseudo-reduced
Z can also be determined from
specific volume
a knowledge of PR and vR.

Comparison of Z factors for various gases. 30

 OTHER EQUATIONS OF STATE

Several equations have been proposed to

represent the P-v-T behavior of substances
accurately over a larger region with no
limitations.

Van der Waals Critical isotherm

Equation of State of a pure
substance has
an inflection
point at the
critical state.

This model includes two effects not considered

in the ideal-gas model: the intermolecular
attraction forces and the volume occupied by the
molecules themselves. The accuracy of the van
der Waals equation of state is often inadequate. 31
Beattie-Bridgeman Equation of State

The constants are given in

Table 3–4 for various
substances. It is known to be
reasonably accurate for
densities up to about 0.8cr.

Benedict-Webb-Rubin Equation of State

The constants are given in Table 3–4. This equation can handle substances
at densities up to about 2.5 cr.

Virial Equation of State

The coefficients a(T), b(T), c(T), and so on, that are

functions of temperature alone are called virial coefficients.
32
33
 Summary
• Pure substance
• Phases of a pure substance
• Phase-change processes of pure substances
 Compressed liquid, Saturated liquid, Saturated vapor, Superheated vapor
 Saturation temperature and Saturation pressure
• Property diagrams for phase change processes
 The T-v diagram, The P-v diagram, The P-T diagram, The P-v-T surface
• Property tables
 Enthalpy
 Saturated liquid, saturated vapor, Saturated liquid vapor mixture, Superheated
vapor, compressed liquid
 Reference state and reference values
• The ideal gas equation of state
 Is water vapor an ideal gas?
• Compressibility factor
• Other equations of state
 van der Waals Equation of State, Beattie-Bridgeman Equation of State
 Benedict-Webb-Rubin Equation of State, Virial Equation of State
34