Andrew

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

2MX-1710-2690-33-20.

5i-M
Model: AMB452000v06

Electrical Properties
1710 - 2690
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690

Polarization +45° , -45°

Electrical downtilt (°) 0 - 10 , continuously adjustable


at mid Tilt 19.2 19.7 20.0 20.2
Gain (dBi)
over all Tilts 19.0 ±0.6 19.5 ±0.6 19.8 ±0.5 20.0 ±0.8
Side lobe suppression for first side
> 17 > 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 34 ±2.1 31 ±2.3 29 ±0.5 27 ±1.0

Vertical 3dB beam width (°) 6.4 ±0.5 5.9 ±0.4 5.1 ±0.2 4.7 ±0.3

VSWR < 1.5

Horizontal beam centers (°) ± 30 ± 27 ± 25 ± 23

Cross polar isolation (dB) Same beam: ≥ 28

Front to back ratio, ±30° (dB) > 32 > 32 > 32 > 32

Cross polar ratio (dB) 0° > 20 > 20 > 22 > 22

Max. power per input (W) 250 (at 50℃ ambient temperature)

Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)

Impedance (Ω) 50

Grounding DC Ground

1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).


2. Electrical datasheet in XML format is available.

Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1468 x 349 x 166
Packing dimensions (H x W x D) (mm) 1870 x 415 x 240
Antenna weight (kg) 18.0
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 29.2 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 500 (at 150 km/h)
Wind load (N) Lateral: 165 (at 150 km/h)
Rear side: 530 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 4 x 4.3-10 Female
Connector position Bottom

Accessories
Item Model Description Weight Units per antenna

Downtilt kit ASMDT0C01 Mechanical downtilt: 0 - 16 ° 2.1 kg 1 (Separate packing)

1
2MX-1710-2690-33-20.5i-M
Model: AMB452000v06

This antenna can upgrade to RET antenna when with a remote electrical tilt module.
Model Description Weight Units per antenna

AIMM20D11 Remote electrical tilt module, a couple of AISG connectors 0.6 kg 1 (Separate packing)

106

1286

1468
Pattern sample for reference

1710 - 2690 MHz 1710 - 2690 MHz


(yy-30) (y+30)
NOTE

1. Facilities, such as towers and poles, must bear the weight and wind load of antennas.
2. HUAWEI ‘s standard brackets and accessories must be used for any installation.
3. The antenna working environment must meet the requirements specified in the datasheet.
4. Only qualified personnel are allowed to perform installation. Installation tools and procedures must conform to
requirements described in the antenna installation guide.

Huawei Technologies Co., Ltd. Bantian, Longgang District, Shenzhen 518129, P.R.China www.huawei.com/antenna
Any previous datasheet issues become invalid. 2 Issue: 2016-06-01

You might also like