Scribd
Upload
85 views

Programming Interface Installation Instructions Updated 4-22-2015

To program Inventronics devices, one must install the correct programming interface on a PC along with the device driver. This requires obtaining the appropriate programmer, downloading and installing the interface and driver, and connecting the PC, programmer and device according to diagrams. Settings are then programmed into the device and verified by reading the programmed values.

Uploaded by

Abraham Seco Armesto
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
85 views

Programming Interface Installation Instructions Updated 4-22-2015

To program Inventronics devices, one must install the correct programming interface on a PC along with the device driver. This requires obtaining the appropriate programmer, downloading and installing the interface and driver, and connecting the PC, programmer and device according to diagrams. Settings are then programmed into the device and verified by reading the programmed values.

Uploaded by

Abraham Seco Armesto
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Installation Instructions for Programming Interfaces April 22, 2015

For Inventronics’ programmable drivers & control modules, settings may be changed through the
corresponding Programming Interface which must be installed on a PC and connected to the programmable
device through its programmer as illustrated in the diagrams below.

1. Obtain the correct programmer for the device to be programmed, along with its datasheet:
a. PRG-MUL2 for non-DMX drivers and control modules (The older SDD-AAPNP Multi
Programmer works also for 0-10V drivers.)
b. PRG-DMX for DMX drivers
c. PRG-CSIM for the CSIM-100 Control Signal Integration Module

2. Device Driver installation (if the Inventronics driver has never been installed)

Download & run the “Programming Interface Driver” from http://www.inventronics-


co.com/download.aspx?c_kind=3&c_kind2=17&c_kind3=154 (also accessible from
www.inventronics-co.com by selecting Sales & Services, Downloads)

3. Framework 4.0 installation (skip for Windows 8.1, where it’s already included)

Install the framework4.0 software from Microsoft website (http://www.microsoft.com/en-


US/download/details.aspx?id=17718)

4. Programming Interface installation

Download the correct Programming Interface for the programmer from http://www.inventronics-
co.com/download.aspx?c_kind=3&c_kind2=17&c_kind3=154 (also accessible from
www.inventronics-co.com by selecting Sales & Services, Downloads)

Note: The software installation may be interrupted by virus checking software. If this happens,
disable the virus checking software, install the programming interface, then re-enable the virus
checking software.

5. Referring to the “programming connection diagram” in the datasheet of the device to be programmed,
connect the PC, programmer, device to be programmed, and any other equipment shown.

6. Open the icon that was automatically added to the desktop.

7. If applicable, select the device type to be programmed, then press “Startup.”

Example: Select “0-10V dimming driver” if the driver’s suffix starts with “D” like in LUD-060S150DSF.

8. Proceed with programming according to the datasheet of the programmer and device to be programmed.

Perform a “Write Driver” operation to load the selected settings into the driver, then “Read Driver”
will display the exact values stored (which may be slightly different from the values entered).

If either of these operations fail, uncheck the “Matching” box, ensure the correct Series and Model
numbers are selected, then try again.

1/3
Specifications are subject to changes without notice.

www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 [email protected]


Installation Instructions for Programming Interfaces April 22, 2015

Example Programming Connection Diagram for an Intelligent LED Driver


(see driver datasheet for the applicable diagram)

Example Programming Connection Diagram for a Control Module

2/3
Specifications are subject to changes without notice.

www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 [email protected]


Installation Instructions for Programming Interfaces April 22, 2015
Revision History
Change Description of Change
Rev.
Date Item From To

2014-12-03 A Release / /

3/3
Specifications are subject to changes without notice.

www.inventronics-co.com Tel: 86-571-56565800 Fax: 86-571-86601139 [email protected]

You might also like