2nd Periodical Test

TLE (EIM NC-II) Grade 9

Direction: Identify the safety symbols. Choose from the options below and then
write the letter on your answer sheet.
___1. It is used without the safety alert symbol indicating a potentially hazardous situation
which, if not avoided, may result in property damage.
___2. It indicates an imminently hazardous situation which, if not avoided, may result in
death or serious injury.
____3. It indicates a potentially hazardous situation which, if not avoided, may result in minor
or serious injury.
____4. Read and understand the instruction manual.
____5. It indicates a potentially hazardous situation which, if not avoided, may result in death
or serious injury.
____6. Potential Personal Injury Hazards
____7. PROHIBITION

Direction: Identify the type of manual to be used under the following situation.
Write the correct answer on your answer sheet.
_____8. There is something wrong with the normal function of the product after
warranty period.
a. Normal usage instruction b. troubleshooting guide
c. Warranty information d. Service location
_____9. Untoward accident has to be prevented using power tools.
a. Normal usage instruction b. troubleshooting guide
b. Safety instruction d. Service location
_____10. One week after purchasing of the products, trouble has occurred.
a. Normal usage instruction b. troubleshooting guide
c. Warranty information d. Service location
_____11. Dismantled parts need complete assembly after the repair.
a. Assembly instruction b. troubleshooting guide
c. Service location d. Safety instruction
_____12. Determine if the product has passed the quality standards.
a. Warranty information b. Regulatory code
c. troubleshooting guide d. Service location

Direction: Identify the type of lubricant that is needed. Write, “RUST

REMOVER”, “SOLID LUBRICANT”, “OIL”, “GREASE”, AND PENETRATING
LUBRICANT” on your answer sheet.
____________13. Removing rust from bolts, hand tools, bicycle chain and equipment
parts.
____________14. Maintaining heavy structures like garage door or gate and other
related tasks.
____________15. Application of maintenance activity for common hand tools,
equipment and other hardware.
____________16. Recommended to be used on rubber, car door gaskets, and window
sashes.
____________17. Maintenance for stock-up parts like bearing, bushing, and heavy
bolts and nuts.
Direction: Identify the following information by writing “ALWAYS” and
“NEVER” before each number. Use separate sheet for your answers.
_________ 18.Perform regular check or the condition of tools, instrument and
equipment.
_________ 19. Place electrical leads in areas where they can be damaged.
_________ 20. Assign competent people to repair damaged electrical leads, tools and
equipment.
_________ 21. Decrease cost of replacement.
_________ 22. Test and tag electrical tools and equipment regularly.
_________ 23. Use damaged electrical leads, tools and equipment.
_________ 24. Use safety switches when using electrical tools and equipment.
_________ 25. Improved system reliability.
_________ 26. Apply preventive maintenance on tools and equipment to prevent
electrocution.
_________ 27. Use electrical leads, tools and equipment in damp a wet condition.

Direction: Read the instruction in each sub-test. Write your answer in the space provided before the item
number.

A. Classify the following cleaning solvents as Polar or Nonpolar. Write P for

polar and NP for nonpolar.
______28. water
______29. gasoline
______30. kerosene
______31. diesoline
______32. thinner
______33. detergent soap
B. Identify the cleaning solvents used in the following substances.
______34. Polar substances
a. dust b. mud
______35. Nonpolar substances
a. oil b. grease oil

C. Match each cleaning solvent with its uses. Write the letter of your answer.
Uses
______36. It is used to clean upholstery and other furniture.
______37. It is used to wash out spilled paint on the floors and walls as well as on the tools/ equipment.
______38. It is used to wash out oil, and grease from tools and equipment.
______39. It is used to remove dust, grease and oil.
______40. It is used to clean oil engine, transmission and other parts of the vehicle.

Cleaning Solvents
A. alcohol B. diesoline C. gasoline D. kerosene E. soap and water F. thinner

Direction: Write the letter of the correct answer in your answer sheet.
______41. What measuring device is used by an electrician to measure value of voltage,
current, and resistance?
a. Volt-Ohmmeter c. Megger
b. Multi-tester d. Drilling Equipment
______42. These are electrical materials in which splices and joints are being made.
a. Utility box c. Square Box
b. Junction box d. Electrical Boxes
______43. What action can be carried out to retain an item or to restore it to a
functional condition?
a. repair and maintenance c. corrective maintenance
b. emergency maintenance d. Maintenance
______44. It is an electrical device used in controlling the flow of current in a circuit or
even the entire circuit.
a. Flush type switch c. Main switch
b. Tumbler switch d. Switches
______45. Electrical conductors which is single, usually cylindrical, flexible strand or
 iron rod of metal.
a. Stranded conductor b. Wires c. Cables d. Conductors
______46. Which of the following should we use to keep a flammable cleaning solvent?
a. closed tin container b. plastic pail c. aluminum basin
______47. As a safety precaution, which of the following safety devices should be
worn in electrical wiring ?
a. face shield b. rubber gloves c. Apron
_____48. Which of the following solvents should not be used as a cleaning solution for it poses hazards
to health?
a. gasoline b. kerosene c. carbon tetrachloride
_____49. What can the operator expect to happen when the wire brush attachment is used on the
portable disc grinder?
a. The grinder may be jumped out or be thrown out.
b. The grinder moves back and forth.
c. The grinder stays steady on the material being bushed.
d. The grinder performs well.
____50. Why is it necessary to tighten the disk lock nut snuggly only when the disc is
replaced on the portable disc grinder?
a. The threads will be stripped on the spindle.
b. The disc may be too difficult to remove next time.
c. The natural rotation of the disc and spindle will cause the threads to tighten.
d. The loose threads are allowed to hold some of the vibration created by the portable disc
grinder.

GOOD LUCK!!!
Prepared by:

JOEMAR L. BAQUIRAN
EIM NC-II Teacher Approved:
MARCELO B. RALUTIN 1
School Head