1

©2014 Welch Allyn, Inc.

MM 721462 Ver. C

Fiber optic laryngoscope handles

Directions for use
Intended use
The fiber optic laryngoscope handle is an accessory used with compatible rigid fiber optic
laryngoscope blades which are used to examine and visualize a patient’s airway and aid
placement of a tracheal tube.

About this document

This directions for use apply to Welch Allyn reusable fiber optic laryngoscope handles:
60813, 60814, 60815. Welch Allyn reusable fiber optic laryngoscope handles may be used
with Welch Allyn fiber optic laryngoscope blades MacIntosh REF: 6906X, English
MacIntosh REF: 6921X, and Miller REF: 6806X.

Warnings and cautions

WARNING: Reusable fiber optic laryngoscope handles must be reprocessed after each
use.
WARNING: The reprocessing procedure and the equipment and materials described
must be followed and conducted by persons trained and familiar with medical device
reprocessing.
WARNING: Consult cleaning and disinfecting agent manufacturer instructions for their
proper preparation and use.
WARNING: Repeated reprocessing may degrade elements of the handle. Follow
inspection procedures to assure damage has not occurred to the handle.
WARNING: High level disinfection and/or sterilization are not achieved by these
methods.
WARNING: Lamps, if left illuminated, could generate sufficient heat to cause burns
WARNING: Discard any component that shows evidence of damage or
deterioration.
WARNING: Do not modify this equipment. Any modification of this equipment may
lead to patient injury. Any modification of this equipment voids the product warranty.
WARNING: Personnel shall follow their facility policies and procedures and wear
appropriate personal protective equipment when handling potentially contaminated
equipment.
WARNING: Laryngoscope equipment is not suitable for use in intense magnetic fields

CAUTION: Only use lamp specified. Failure to follow these instructions may cause
damage or poor performance of the handle.

CAUTION: If the device will be unused for several months or longer, remove the
batteries prior to storing the device.
2 Directions for use Welch Allyn fiber optic laryngoscope handles

Reprocessing instructions
These reprocessing instructions refer to procedures for cleaning and intermediate level
disinfection. Fiber optic laryngoscope handles must be reprocessed prior to first use and
between each use using the following method as outlined in this document:

• Cleaning and intermediate level disinfection

Welch Allyn has validated the above instruction as being capable of preparing these
laryngoscope handles for re-use. The user must ensure that the reprocessing as actually
performed by the user's personnel, with the user's equipment and materials, achieves the
desired result. This may require validation and routine monitoring of the user's actual process

NOTE: The main handle and bottom cap components are compatible with the disinfection
solution and autoclave methods identified which are provided for facilities who wish to perform
either method after cleaning and intermediate level disinfection.

Cleaning and intermediate level disinfection instructions

Point of use: 1. Separate blade assembly from handle and place handle
into suitable containment for subsequent reprocessing
(per figure 1). Do not place handle with sharp devices.
2. Prevent the handle from drying (i.e. wrap/cover in moist
germicidal wipe).
Preparation for 1. Select an appropriate quaternary ammonium
decontamination: isopropanol based germicidal cleaner labeled suitable
for use on healthcare equipment and capable
intermediate level disinfection. Reference EPA-
registered disinfectants:
http://www.epa.gov/oppad001/chemregindex.htm
Outside of the U.S., please consult applicable
regulatory body for equivalent quaternary ammonium
isopropanol germicidal cleaner.

2. Remove batteries and lamp cartridge (per figure 2).

Directions for use Welch Allyn fiber optic laryngoscope handles 3

Cleaning and 1. Follow the germicidal wipe manufacturer’s instructions

intermediate level to clean all exposed surfaces of the main handle, end
disinfection: cap, and lamp cartridge.
2. If necessary, brush with a dry, soft-bristled brush and
re-wipe to loosen/remove excessive visible soil.
3. After all visible soil is removed, re-wipe to wet all
surfaces and allow adequate contact time for
disinfection as directed by the germicidal wipe
manufacturer.
CAUTION: Only use quaternary ammonium
isopropanol based germicidal wipes.

Drying: Allow components to air dry.

Maintenance, 1. Inspect each component area (per figure 3) for damage or

Inspection and Testing deterioration.
WARNING: Discard any component that shows
evidence of damage or deterioration.
Contact Welch Allyn for component replacement.
2. Reassemble handle (per figure 4) with new or
batteries in known good condition.
3 . Attach handle to a clean and disinfected test blade
assembly in known working condition. Verify that:
• Blade assembly engages and locks onto handle.
• Blade assembly deploys into its locked position on
handle AND lamp illuminates.
• Light output is satisfactory.
If the lamp fails to light or output is low, check or
replace the lamp and/or batteries.
Storage Store handle per facility practice to allow device to remain
clean, dry, and ready for service.

End of reprocessing instructions for intermediate level disinfection.

4 Directions for use Welch Allyn fiber optic laryngoscope handles

Cold solution disinfection instructions

NOTE: The main handle and bottom cap are compatible with this cold solution disinfection
method which is provided for facilities who wish to solution disinfect after cleaning and
intermediate level disinfection.

Disassembly: 1. Disassemble the handle and remove batteries and

lamp cartridge per figures 3.

2. Set batteries and lamp cartridge aside.

Preparation for 1. Select a 14 day (2.4 – 2.6%) glutaraldehyde
decontamination: disinfectant.
2. Prepare disinfection solution per manufacturer
instructions.
Cold solution 1. Immerse main handle and bottom cap (only) in disinfection
disinfection: solution, for a time duration identified by the disinfection
solution manufacturer.
2. Thoroughly rinse all components in potable water,
softened water or per disinfection solution manufacturer
instructions to remove disinfecting solution.
Drying: Dry all components with a clean cloth or allow to air dry.
Maintenance, 1. Inspect each component area (per figure 2) for damage or
Inspection and Testing deterioration.
WARNING: Discard any component that shows
evidence of damage or deterioration.
Contact Welch Allyn for component replacement.
2. Reassemble handle (per figure 4) with new or batteries in
known good condition.
3. Attach handle to a clean and disinfected test blade
assembly in known working condition. Verify that:
• Blade assembly engages and locks onto handle.
• Blade assembly deploys into its locked position on
handle AND lamp illuminates.
• Light output is satisfactory
If the lamp fails to light or output is low, check or
replace the lamp or batteries.
Store handle per facility practice to allow device to remain
Storage clean, dry, and ready for service.
Directions for use Welch Allyn fiber optic laryngoscope handles 5

Autoclave instructions
NOTE: The main handle and bottom cap are compatible with these autoclave methods which
are provided for facilities who wish to autoclave after cleaning and intermediate level
disinfection.

Disassembly: 1. Disassemble the handle and remove batteries and

lamp cartridge per figures 3.

2. Set batteries and lamp cartridge aside.

After battery and lamp cartridge removal, select ONE of the following autoclave
methods below for the main handle and bottom cap:
Gravity autoclave: Follow equipment manufacturer and facility procedures in the
set-up and operation of autoclave equipment. Gravity autoclave settings are as
follows:
• Temperature: 132 C (270 F)
• Exposure time: 3 minutes (unwrapped)
• Minimum dry time: 1 minute
Pre-vacuum autoclave: Follow equipment manufacturer and facility procedures in the
set-up and operation of autoclave equipment. Pre-vacuum autoclave settings are as
follows:
• Temperature: 132 C (270 F)
• Exposure time: 3 minutes (unwrapped)
• Minimum dry time: 1 minute

Maintenance, 1. Inspect each component area (per figure 2) for damage or

Inspection and Testing deterioration.
WARNING: Discard any component that shows
evidence of damage or deterioration.
Contact Welch Allyn for component replacement.
2. Reassemble (per figure 4) with new or batteries in known
good condition.
3. Attach handle to a clean and disinfected test blade
assembly in known working condition. Verify that:
• Blade assembly engages and locks onto handle.
• Blade assembly deploys into its locked position on
handle AND lamp illuminates.
• Light output is satisfactory.
If the lamp fails to light or output is low, check or
replace the lamp and/or batteries
Storage: Store handle per facility practice to allow device to remain
clean, dry, and ready for service.
6 Directions for use Welch Allyn standard laryngoscope handles

Maintenance instructions

Replace the lamp

WARNING: Lamps, if left illuminated, could generate sufficient heat to

cause burns.

CAUTION: Use only Welch Allyn replacement lamps REF: 06000 to ensure
proper illumination alignment.
1. Unscrew bottom cap of handle counterclockwise and remove batteries per figure 3.
2. Remove lamp cartridge assembly from main handle by applying finger pressure in the
direction shown by the arrow per figure 4.
3. Remove shroud cap from shroud by rotating shroud cap counterclockwise per figures 5
and 6.
4. Rotate lamp counterclockwise to remove per figure 6.
5. Replace lamp and rotate shroud cap clockwise to tighten per figure 7.
6. To replace lamp cartridge assembly in the main handle, invert handle, then gently slide
the cartridge down the inside of handle, tipping it side to side until the shroud cap
exits opening on top.
7. Re-insert batteries and apply slight pressure to set the cartridge in place.
8. Replace and tighten bottom cap.
9. Reprocess repaired assembly as appropriate per these instructions.

Figure 3 Figure 4

Figure 5 Figure 6
1. Shroud cap
2. Lamp
3. Shroud

Figure 7
Directions for use Welch Allyn standard laryngoscope handles 7

Replace the batteries

1. Unscrew bottom cap of handle per figure 3 and remove batteries.

2. Alkaline batteries are supplied with your handle for maximum performance and
are recommended as replacements; however carbon-zinc batteries may also be
used.
• Medium handle, REF 60813 uses two “C” size
• Penlight handle, REF 60814 uses two “AA” size
• Stubby handle, REF 60815 uses two “AA” size
3. Insert batteries and reinstall bottom cap per figure 3.
4. Verify lamp and blade engagement/operation using a known working test blade.
5. Reprocess repaired assembly as appropriate per these instructions.

Specifications
Electrical:
For information about electromagnetic compatibility (EMC) see Welch Allyn website:
http://www.welchallyn.com

Operating: Storage/Transport:
104 F 120 F
(40 C) (49 C)
32 F -4 F
(0 C) (-20 C)

Approvals:
Conforms to ASTM F 965 and ISO-7376-1, IEC/EN 60601-1, IEC/EN 60601-1-2

The CE mark on this product indicates that it has been tested to and conforms
with the provisions noted within the 93/42/EEC Medical Device Directive.
Complies with EMC Framework of Australia

Warranty:
One year

Service Information:
For Technical Support or to obtain information about any Welch Allyn product, contact
Welch Allyn Technical Support: www.welchallyn.com/support.

Welch Allyn, Inc. Authorized European Representative Address:

4341 State Street Road Regulatory Affairs Representative
Skaneateles Falls, NY 13153-0220 USA Welch Allyn, Limited
www.welchallyn.com
Navan Business Park
Dublin Road
Navan, County Meath, Republic of Ireland