LECTURE NOTES

ON
ENGINEERING DRAWING

2018 – 2019
I B. Tech I Semester (Autonomous-R17)

Dr. CH. Lakshmi Tulasi, Associate Professor

Dr. G. Maruthi Prasad YADAV, Associate Professor
Mr. N. Rajesh, Associate Professor

CHADALAWADA RAMANAMMA
ENGINEERING COLLEGE
(AUTONOMOUS)
Chadalawada Nagar, Renigunta Road, Tirupati – 517 506

Department of Freshman Engineering

Engineering Curves – I

1. Classification

2. Conic sections - explanation

3. Common Definition

4. Ellipse – ( six methods of construction)

5. Parabola – ( Three methods of construction)

6. Hyperbola – ( Three methods of construction )

7. Methods of drawing Tangents & Normals ( four cases)

Engineering Curves – II

1. Classification

2. Definitions

3. Involutes - (five cases)

4. Cycloid

5. Trochoids – (Superior and Inferior)

6. Epic cycloid and Hypo - cycloid

7. Spiral (Two cases)

8. Helix – on cylinder & on cone

9. Methods of drawing Tangents and Normals (Three cases)

 ENGINEERING CURVES
Part- I {Conic Sections}

ELLIPSE PARABOLA HYPERBOLA

1.Concentric Circle Method 1.Rectangle Method 1.Rectangular Hyperbola

(coordinates given)
2.Rectangle Method 2 Method of Tangents
( Triangle Method) 2 Rectangular Hyperbola
3.Oblong Method (P-V diagram - Equation given)
3.Basic Locus Method
4.Arcs of Circle Method (Directrix – focus) 3.Basic Locus Method
(Directrix – focus)
5.Rhombus Metho

6.Basic Locus Method Methods of Drawing

(Directrix – focus) Tangents & Normals
To These Curves.
 CONIC SECTIONS
ELLIPSE, PARABOLA AND HYPERBOLA ARE CALLED CONIC SECTIONS
BECAUSE
THESE CURVES APPEAR ON THE SURFACE OF A CONE
WHEN IT IS CUT BY SOME TYPICAL CUTTING PLANES.
OBSERVE
ILLUSTRATIONS
GIVEN BELOW..

Ellipse

Section Plane Section Plane

Through Generators Hyperbola
Parallel to Axis.

Section Plane Parallel

to end generator.
 COMMON DEFINATION OF ELLIPSE, PARABOLA & HYPERBOLA:
These are the loci of points moving in a plane such that the ratio of it’s distances
from a fixed point And a fixed line always remains constant.
The Ratio is called ECCENTRICITY. (E)
A) For Ellipse E<1
B) For Parabola E=1
C) For Hyperbola E>1

Refer Problem nos. 6. 9 & 12

SECOND DEFINATION OF AN ELLIPSE:-
It is a locus of a point moving in a plane
such that the SUM of it’s distances from TWO fixed points
always remains constant.
{And this sum equals to the length of major axis.}
These TWO fixed points are FOCUS 1 & FOCUS 2
Refer Problem no.4
Ellipse by Arcs of Circles Method.
 ELLIPSE
BY CONCENTRIC CIRCLE METHOD
Problem 1 :-
Draw ellipse by concentric circle method.
Take major axis 100 mm and minor axis 70 mm long. 3
2 4
Steps:
1. Draw both axes as perpendicular bisectors C
of each other & name their ends as shown.
2. Taking their intersecting point as a center, 1 5
3
2 4
draw two concentric circles considering both
as respective diameters.
1 5
3. Divide both circles in 12 equal parts &
name as shown.
A B
4. From all points of outer circle draw vertical
lines downwards and upwards respectively.
5.From all points of inner circle draw 10 6
horizontal lines to intersect those vertical
lines. 10 9 7 6
6. Mark all intersecting points properly as 8
those are the points on ellipse. D
7. Join all these points along with the ends of
both axes in smooth possible curve. It is 9 7
required ellipse.
8
Steps:
ELLIPSE
BY RECTANGLE METHOD
1 Draw a rectangle taking major
and minor axes as sides.
2. In this rectangle draw both Problem 2
axes as perpendicular bisectors of
Draw ellipse by Rectangle method.
each other..
3. For construction, select upper Take major axis 100 mm and minor axis 70 mm long.
left part of rectangle. Divide
vertical small side and horizontal
long side into same number of D 4
4
equal parts.( here divided in four
parts) 3 3
4. Name those as shown..
5. Now join all vertical points 2 2
1,2,3,4, to the upper end of minor
1 1
axis. And all horizontal points
i.e.1,2,3,4 to the lower end of
minor axis. A B
6. Then extend C-1 line upto D-1
and mark that point. Similarly
extend C-2, C-3, C-4 lines up to
D-2, D-3, & D-4 lines.
7. Mark all these points properly
and join all along with ends A
and D in smooth possible curve.
Do similar construction in right C
side part.along with lower half of
the rectangle.Join all points in
smooth curve.
It is required ellipse.
 ELLIPSE
Problem 3:- BY OBLONG METHOD
Draw ellipse by Oblong method.
Draw a parallelogram of 100 mm and 70 mm long
sides with included angle of 750.Inscribe Ellipse in it.
STEPS ARE SIMILAR TO
THE PREVIOUS CASE
(RECTANGLE METHOD)
ONLY IN PLACE OF RECTANGLE,
HERE IS A PARALLELOGRAM.

4 4

3 3

2 2

1
1

A B
PROBLEM 4. ELLIPSE
MAJOR AXIS AB & MINOR AXIS CD ARE
BY ARCS OF CIRCLE METHOD
100 AMD 70MM LONG RESPECTIVELY
.DRAW ELLIPSE BY ARCS OF CIRLES
METHOD. As per the definition Ellipse is locus of point P moving in
a plane such that the SUM of it’s distances from two fixed
STEPS: points (F1 & F2) remains constant and equals to the length
1.Draw both axes as usual.Name the of major axis AB.(Note A .1+ B .1=A . 2 + B. 2 = AB)
ends & intersecting point
2.Taking AO distance I.e.half major
axis, from C, mark F1 & F2 On AB . p4 C
( focus 1 and 2.) p3
3.On line F1- O taking any distance, p2
mark points 1,2,3, & 4
p1
4.Taking F1 center, with distance A-1
draw an arc above AB and taking F2
center, with B-1 distance cut this arc.
Name the point p1 B
5.Repeat this step with same centers but A O
F1 1 2 3 4 F2
taking now A-2 & B-2 distances for
drawing arcs. Name the point p2
6.Similarly get all other P points.
With same steps positions of P can be
located below AB.
7.Join all points by smooth curve to get
an ellipse/
D
PROBLEM 5. ELLIPSE
DRAW RHOMBUS OF 100 MM & 70 MM LONG BY RHOMBUS METHOD
DIAGONALS AND INSCRIBE AN ELLIPSE IN IT.

STEPS: 2
1. Draw rhombus of given
dimensions.
2. Mark mid points of all sides &
name Those A,B,C,& D
3. Join these points to the ends of A B
smaller diagonals.
4. Mark points 1,2,3,4 as four
centers.
5. Taking 1 as center and 1-A 3 4
radius draw an arc AB.
6. Take 2 as center draw an arc CD.
7. Similarly taking 3 & 4 as centers
and 3-D radius draw arcs DA & BC.
D C

1
PROBLEM 6:- POINT F IS 50 MM FROM A LINE AB.A POINT P IS MOVING IN A PLANE ELLIPSE
SUCH THAT THE RATIO OF IT’S DISTANCES FROM F AND LINE AB REMAINS CONSTANT
AND EQUALS TO 2/3 DRAW LOCUS OF POINT P. { ECCENTRICITY = 2/3 } DIRECTRIX-FOCUS METHOD

ELLIPSE
A
STEPS:
1 .Draw a vertical line AB and point F
50 mm from it.
2 .Divide 50 mm distance in 5 parts. 45mm
3 .Name 2nd part from F as V. It is 20mm
and 30mm from F and AB line resp.
It is first point giving ratio of it’s
distances from F and AB 2/3 i.e 20/30
4 Form more points giving same ratio such
as 30/45, 40/60, 50/75 etc. (vertex) V
5.Taking 45,60 and 75mm distances from F ( focus)
line AB, draw three vertical lines to the
right side of it.
6. Now with 30, 40 and 50mm distances in
compass cut these lines above and below,
with F as center.
7. Join these points through V in smooth
curve.
This is required locus of P.It is an ELLIPSE.

B
PROBLEM 7: A BALL THROWN IN AIR ATTAINS 100 M HIEGHT
PARABOLA
AND COVERS HORIZONTAL DISTANCE 150 M ON GROUND. RECTANGLE METHOD
Draw the path of the ball (projectile)-

STEPS: 6 6
1.Draw rectangle of above size and
divide it in two equal vertical parts
2.Consider left part for construction. 5 5
Divide height and length in equal
number of parts and name those
1,2,3,4,5& 6 4 4
3.Join vertical 1,2,3,4,5 & 6 to the
top center of rectangle
4.Similarly draw upward vertical
3 3
lines from horizontal1,2,3,4,5
And wherever these lines intersect
previously drawn inclined lines in
sequence Mark those points and 2 2
further join in smooth possible curve.
5.Repeat the construction on right side
rectangle also.Join all in sequence. 1 1
This locus is Parabola.
.

1 2 3 4 5 6 5 4 3 2 1
Problem no.8: Draw an isosceles triangle of 100 mm long base and PARABOLA
110 mm long altitude.Inscribe a parabola in it by method of tangents. METHOD OF TANGENTS

Solution Steps: C
1. Construct triangle as per the given
dimensions.
2. Divide it’s both sides in to same no.of
equal parts.
3. Name the parts in ascending and
descending manner, as shown.
4. Join 1-1, 2-2,3-3 and so on.
5. Draw the curve as shown i.e.tangent to
all these lines. The above all lines being
tangents to the curve, it is called method
of tangents.

A B
PROBLEM 9: Point F is 50 mm from a vertical straight line AB. PARABOLA
Draw locus of point P, moving in a plane such that DIRECTRIX-FOCUS METHOD
it always remains equidistant from point F and line AB.

PARABOLA
SOLUTION STEPS:
1.Locate center of line, perpendicular to A
AB from point F. This will be initial
point P and also the vertex.
2.Mark 5 mm distance to its right side,
name those points 1,2,3,4 and from P1
those
draw lines parallel to AB.
3.Mark 5 mm distance to its left of P and (VERTEX) V
name it 1.
O 1 2 3 4
F
4.Take O-1 distance as radius and F as
center draw an arc ( focus)
cutting first parallel line to AB. Name
upper point P1 and lower point P2.
P2
(FP1=O1)

5.Similarly repeat this process by taking

again 5mm to right and left and locate
P3P4.
B
6.Join all these points in smooth curve.

It will be the locus of P equidistance

from line AB and fixed point F.
Problem No.10: Point P is 40 mm and 30 mm from horizontal HYPERBOLA
and vertical axes respectively.Draw Hyperbola through it. THROUGH A POINT
OF KNOWN CO-ORDINATES
Solution Steps:
1) Extend horizontal
line from P to right side. 2
2) Extend vertical line
from P upward.
3) On horizontal line
from P, mark some points
taking any distance and
name them after P-1,
2,3,4 etc.
4) Join 1-2-3-4 points
to pole O. Let them cut 1
part [P-B] also at 1,2,3,4
points.
5) From horizontal
1,2,3,4 draw vertical 2 1 P 1 2 3
lines downwards and
6) From vertical 1,2,3,4
points [from P-B] draw
1
horizontal lines.
7) Line from 1 40 mm 2
horizontal and line from
1 vertical will meet at 3
P1.Similarly mark P2, P3,
P4 points. O
8) Repeat the procedure
by marking four points 30 mm
on upward vertical line
from P and joining all
those to pole O. Name
this points P6, P7, P8 etc.
and join them by smooth
curve.
Problem no.11: A sample of gas is expanded in a cylinder HYPERBOLA
from 10 unit pressure to 1 unit pressure.Expansion follows
law PV=Constant.If initial volume being 1 unit, draw the
P-V DIAGRAM
curve of expansion. Also Name the curve.

Form a table giving few more values of P & V 10

P V = C 9
10 1 = 10
5 2 = 10 8
4 2.5 = 10
2.5 4 = 10 7
2 5 = 10
1 10 = 10 6

PRESSURE
Now draw a Graph of 5

( Kg/cm2)
Pressure against Volume.
It is a PV Diagram and it is Hyperbola.
Take pressure on vertical axis and
4
Volume on horizontal axis.
3
2

0 1 2 3 4 5 6 7 8 9 10

VOLUME:( M3 )
PROBLEM 12:- POINT F IS 50 MM FROM A LINE AB.A POINT P IS MOVING IN A PLANE HYPERBOLA
SUCH THAT THE RATIO OF IT’S DISTANCES FROM F AND LINE AB REMAINS CONSTANT
AND EQUALS TO 2/3 DRAW LOCUS OF POINT P. { ECCENTRICITY = 2/3 }
DIRECTRIX
FOCUS METHOD

STEPS: A
1 .Draw a vertical line AB and point F
50 mm from it.
2 .Divide 50 mm distance in 5 parts. 30mm
3 .Name 2nd part from F as V. It is 20mm
and 30mm from F and AB line resp.
It is first point giving ratio of it’s
distances from F and AB 2/3 i.e 20/30
4 Form more points giving same ratio such
as 30/45, 40/60, 50/75 etc. (vertex)
V
F ( focus)
5.Taking 45,60 and 75mm distances from
line AB, draw three vertical lines to the
right side of it.
6. Now with 30, 40 and 50mm distances in
compass cut these lines above and below,
with F as center.
7. Join these points through V in smooth
curve.
This is required locus of P.It is an ELLIPSE.

B
 ELLIPSE
Problem 13:
TANGENT & NORMAL
TO DRAW TANGENT & NORMAL
TO THE CURVE FROM A GIVEN POINT ( Q )
1. JOIN POINT Q TO F1 & F2
2. BISECT ANGLE F1Q F2 THE ANGLE BISECTOR IS NORMAL
3. A PERPENDICULAR LINE DRAWN TO IT IS TANGENT TO THE CURVE.

p4 C
p3
p2
p1

A B
O
F1 1 2 3 4 F2

D
 ELLIPSE
Problem 14:
TANGENT & NORMAL
TO DRAW TANGENT & NORMAL
TO THE CURVE
ELLIPSE
FROM A GIVEN POINT ( Q ) A

1.JOIN POINT Q TO F. T
2.CONSTRUCT 900 ANGLE WITH
THIS LINE AT POINT F
3.EXTEND THE LINE TO MEET DIRECTRIX
AT T
4. JOIN THIS POINT TO Q AND EXTEND. THIS IS
TANGENT TO ELLIPSE FROM Q (vertex) V
5.TO THIS TANGENT DRAW PERPENDICULAR
F ( focus)
LINE FROM Q. IT IS NORMAL TO CURVE. 900
N

Q
N

T
 PARABOLA
Problem 15: TANGENT & NORMAL
TO DRAW TANGENT & NORMAL
TO THE CURVE T PARABOLA
FROM A GIVEN POINT ( Q )
A

1.JOIN POINT Q TO F.
2.CONSTRUCT 900 ANGLE WITH
THIS LINE AT POINT F
3.EXTEND THE LINE TO MEET DIRECTRIX
AT T
4. JOIN THIS POINT TO Q AND EXTEND. THIS IS VERTEX V
TANGENT TO THE CURVE FROM Q 900
F
5.TO THIS TANGENT DRAW PERPENDICULAR ( focus)
LINE FROM Q. IT IS NORMAL TO CURVE.
N

Q
B N

T
 HYPERBOLA
Problem 16
TANGENT & NORMAL
TO DRAW TANGENT & NORMAL
TO THE CURVE
FROM A GIVEN POINT ( Q ) A

1.JOIN POINT Q TO F.
2.CONSTRUCT 900 ANGLE WITH THIS LINE AT
POINT F T
3.EXTEND THE LINE TO MEET DIRECTRIX AT T
4. JOIN THIS POINT TO Q AND EXTEND. THIS IS
TANGENT TO CURVE FROM Q
(vertex)
V
F ( focus)
5.TO THIS TANGENT DRAW PERPENDICULAR 900
LINE FROM Q. IT IS NORMAL TO CURVE.
N

N Q

T
 ENGINEERING CURVES
Part-II
(Point undergoing two types of displacements)

INVOLUTE CYCLOID SPIRAL HELIX

1. Involute of a circle 1. General Cycloid 1. Spiral of 1. On Cylinder
a)String Length = D One Convolution.
2. Trochoid 2. On a Cone
b)String Length > D ( superior) 2. Spiral of
3. Trochoid Two Convolutions.
c)String Length < D ( Inferior)
4. Epi-Cycloid
2. Pole having Composite
shape. 5. Hypo-Cycloid

3. Rod Rolling over

a Semicircular Pole. AND Methods of Drawing
Tangents & Normals
To These Curves.
 DEFINITIONS
CYCLOID:
IT IS A LOCUS OF A POINT ON THE SUPERIORTROCHOID:
PERIPHERY OF A CIRCLE WHICH IF THE POINT IN THE DEFINATION
ROLLS ON A STRAIGHT LINE PATH. OF CYCLOID IS OUTSIDE THE CIRCLE

INFERIOR TROCHOID.:
INVOLUTE: IF IT IS INSIDE THE CIRCLE
IT IS A LOCUS OF A FREE END OF A STRING
WHEN IT IS WOUND ROUND A CIRCULAR POLE EPI-CYCLOID
IF THE CIRCLE IS ROLLING ON
ANOTHER CIRCLE FROM OUTSIDE
SPIRAL: HYPO-CYCLOID.
IT IS A CURVE GENERATED BY A POINT IF THE CIRCLE IS ROLLING FROM
WHICH REVOLVES AROUND A FIXED POINT INSIDE THE OTHER CIRCLE,
AND AT THE SAME MOVES TOWARDS IT.

HELIX:
IT IS A CURVE GENERATED BY A POINT WHICH
MOVES AROUND THE SURFACE OF A RIGHT CIRCULAR
CYLINDER / CONE AND AT THE SAME TIME ADVANCES IN AXIAL DIRECTION
AT A SPEED BEARING A CONSTANT RATIO TO THE SPPED OF ROTATION.
( for problems refer topic Development of surfaces)
 Problem no 17: Draw Involute of a circle. INVOLUTE OF A CIRCLE
String length is equal to the circumference of circle.
Solution Steps:
1) Point or end P of string AP is
exactly D distance away from A.
Means if this string is wound round
the circle, it will completely cover P2
given circle. B will meet A after
winding.
2) Divide D (AP) distance into 8 P3
number of equal parts. P1
3) Divide circle also into 8 number
of equal parts.
4) Name after A, 1, 2, 3, 4, etc. up
to 8 on D line AP as well as on
circle (in anticlockwise direction).
5) To radius C-1, C-2, C-3 up to C-8
draw tangents (from 1,2,3,4,etc to 4 to p
circle). P4
4
6) Take distance 1 to P in compass 3
and mark it on tangent from point 1 5
on circle (means one division less 2
than distance AP). 6
7) Name this point P1 1
8) Take 2-B distance in compass 7 A
and mark it on the tangent from
8
P5 P
point 2. Name it point P2. P8 1 2 3 4 5 6 7 8
9) Similarly take 3 to P, 4 to P, 5 to P7
P up to 7 to P distance in compass P6 
and mark on respective tangents
and locate P3, P4, P5 up to P8 (i.e. D
A) points and join them in smooth
curve it is an INVOLUTE of a given
circle.
 INVOLUTE OF A CIRCLE
Problem 18: Draw Involute of a circle.
String length MORE than D
String length is MORE than the circumference of circle.

Solution Steps: P2
In this case string length is more
than  D.
But remember!
Whatever may be the length of P3 P1
string, mark  D distance
horizontal i.e.along the string
and divide it in 8 number of
equal parts, and not any other
distance. Rest all steps are same
as previous INVOLUTE. Draw
the curve completely.

4 to p
P4 4
3
5
2
6
1
P5 7
8
p8 1 P
2 3 4 5 6 7 8
P7
165 mm
P6 (more than D)
D
Problem 19: Draw Involute of a circle. INVOLUTE OF A CIRCLE
String length is LESS than the circumference of circle. String length LESS than D

Solution Steps: P2
In this case string length is Less
than  D.
But remember!
Whatever may be the length of P3
P1
string, mark  D distance
horizontal i.e.along the string
and divide it in 8 number of
equal parts, and not any other
distance. Rest all steps are same
as previous INVOLUTE. Draw
the curve completely.
4 to p
P4 4
3
5
2
6
1
P5 7 P
8
P7 1 2 3 4 5 6 7 8
P6
150 mm
(Less than D)

D
 PROBLEM 20 : A POLE IS OF A SHAPE OF HALF HEXABON AND SEMICIRCLE.
ASTRING IS TO BE WOUND HAVING LENGTH EQUAL TO THE POLE PERIMETER
INVOLUTE
DRAW PATH OF FREE END P OF STRING WHEN WOUND COMPLETELY. OF
(Take hex 30 mm sides and semicircle of 60 mm diameter.) COMPOSIT SHAPED POLE

SOLUTION STEPS:
Draw pole shape as per
dimensions. P1
Divide semicircle in 4
parts and name those
P
along with corners of
P2
hexagon.
Calculate perimeter
length.

1 to P
Show it as string AP.
On this line mark 30mm
from A
Mark and name it 1
Mark D/2 distance on it
from 1
And dividing it in 4 parts P3
name 2,3,4,5. 3 to P 3
Mark point 6 on line 30 4
2
mm from 5
Now draw tangents from
5 1
all points of pole
and proper lengths as
done in all previous
6 A
involute’s problems and 1 2 3 4 5 6 P
complete the curve. D/2
P4
P6
P5
PROBLEM 21 : Rod AB 85 mm long rolls
over a semicircular pole without slipping
from it’s initially vertical position till it
becomes up-side-down vertical. B
Draw locus of both ends A & B.
A4
Solution Steps? 4
If you have studied previous problems B1
properly, you can surely solve this also.
Simply remember that this being a rod, A3
it will roll over the surface of pole. 3
Means when one end is approaching,
other end will move away from poll.
OBSERVE ILLUSTRATION CAREFULLY!
D 2

A2
B2
2
1
3
1

A1 4
A

B3
B4
PROBLEM 22: DRAW LOCUS OF A POINT ON THE PERIPHERY OF A CIRCLE CYCLOID
WHICH ROLLS ON STRAIGHT LINE PATH. Take Circle diameter as 50 mm

p4
4
p3 p5
3 5

C p2 C1 C2 C3 C4 C5 C6 C7 p6 C
8
2 6

p1
1 p7
7
P p8

D

Solution Steps:
1) From center C draw a horizontal line equal to D distance.
2) Divide D distance into 8 number of equal parts and name them C1, C2, C3__ etc.
3) Divide the circle also into 8 number of equal parts and in clock wise direction, after P name 1, 2, 3 up to 8.
4) From all these points on circle draw horizontal lines. (parallel to locus of C)
5) With a fixed distance C-P in compass, C1 as center, mark a point on horizontal line from 1. Name it P.
6) Repeat this procedure from C2, C3, C4 upto C8 as centers. Mark points P2, P3, P4, P5 up to P8 on the
horizontal lines drawn from 2, 3, 4, 5, 6, 7 respectively.
7) Join all these points by curve. It is Cycloid.
 PROBLEM 23: DRAW LOCUS OF A POINT , 5 MM AWAY FROM THE PERIPHERY OF A SUPERIOR TROCHOID
CIRCLE WHICH ROLLS ON STRAIGHT LINE PATH. Take Circle diameter as 50 mm

4 p4

p3 p5
3 5

p2 C C1 C C3 C4 C5 C6 C7 C8 p 6
2 6 2

p7
1 p1 7
P D p8

Solution Steps:
1) Draw circle of given diameter and draw a horizontal line from it’s center C of length  D and divide it
in 8 number of equal parts and name them C1, C2, C3, up to C8.
2) Draw circle by CP radius, as in this case CP is larger than radius of circle.
3) Now repeat steps as per the previous problem of cycloid, by dividing this new circle into 8 number of
equal parts and drawing lines from all these points parallel to locus of C and taking CP radius wit
different positions of C as centers, cut these lines and get different positions of P and join
4) This curve is called Superior Trochoid.
PROBLEM 24: DRAW LOCUS OF A POINT , 5 MM INSIDE THE PERIPHERY OF A
INFERIOR TROCHOID
CIRCLE WHICH ROLLS ON STRAIGHT LINE PATH. Take Circle diameter as 50 mm

p4
4
p p5
3 5
p2 3
C C1 C2 C3 C4 C5 C6 C7p6 C8
2 6
p1 p7
1 7
P p8

D

Solution Steps:
1) Draw circle of given diameter and draw a horizontal line from it’s center C of length  D and divide it
in 8 number of equal parts and name them C1, C2, C3, up to C8.
2) Draw circle by CP radius, as in this case CP is SHORTER than radius of circle.
3) Now repeat steps as per the previous problem of cycloid, by dividing this new circle into 8 number
of equal parts and drawing lines from all these points parallel to locus of C and taking CP radius
with different positions of C as centers, cut these lines and get different positions of P and join
those in curvature.
4) This curve is called Inferior Trochoid.
PROBLEM 25: DRAW LOCUS OF A POINT ON THE PERIPHERY OF A CIRCLE
WHICH ROLLS ON A CURVED PATH. Take diameter of rolling Circle 50 mm EPI CYCLOID :
And radius of directing circle i.e. curved path, 75 mm.

Solution Steps:
1) When smaller circle will roll on
larger circle for one revolution it will
cover  D distance on arc and it will
be decided by included arc angle .
2) Calculate  by formula  = (r/R) x
Generating/
3600. Rolling Circle
3) Construct angle  with radius OC 4 5
and draw an arc by taking O as center C2
OC as radius and form sector of angle 3 6
.
4) Divide this sector into 8 number of 7
equal angular parts. And from C 2
onward name them C1, C2, C3 up to
1
C8. r = CP P
5) Divide smaller circle (Generating
circle) also in 8 number of equal parts.
And next to P in clockwise direction Directing Circle
name those 1, 2, 3, up to 8.
6) With O as center, O-1 as radius
draw an arc in the sector. Take O-2, O- = r 3600
R
3, O-4, O-5 up to O-8 distances with
center O, draw all concentric arcs in O
sector. Take fixed distance C-P in
compass, C1 center, cut arc of 1 at P1.
Repeat procedure and locate P2, P3,
P4, P5 unto P8 (as in cycloid) and join
them by smooth curve. This is EPI –
CYCLOID.
PROBLEM 26: DRAW LOCUS OF A POINT ON THE PERIPHERY OF A CIRCLE
WHICH ROLLS FROM THE INSIDE OF A CURVED PATH. Take diameter of HYPO CYCLOID
rolling circle 50 mm and radius of directing circle (curved path) 75 mm.

Solution Steps:
1) Smaller circle is rolling
here, inside the larger
circle. It has to rotate
anticlockwise to move P 7
ahead.
2) Same steps should be P1
6
taken as in case of EPI –
CYCLOID. Only change is 1 P2
in numbering direction of
8 number of equal parts
5
on the smaller circle. P3
3) From next to P in 2
anticlockwise direction,
4 P4
name 1,2,3,4,5,6,7,8. 3
4) Further all steps are P5
P8
that of epi – cycloid. This P6 P7
is called
HYPO – CYCLOID.
r
= 3600
R
O

OC = R ( Radius of Directing Circle)

CP = r (Radius of Generating Circle)
Problem 27: Draw a spiral of one convolution. Take distance PO 40 mm.
SPIRAL
IMPORTANT APPROACH FOR CONSTRUCTION!
FIND TOTAL ANGULAR AND TOTAL LINEAR DISPLACEMENT
AND DIVIDE BOTH IN TO SAME NUMBER OF EQUAL PARTS.

P2
Solution Steps 3 1
P1
1. With PO radius draw a circle
and divide it in EIGHT parts. P3
Name those 1,2,3,4, etc. up to 8
2 .Similarly divided line PO also in
EIGHT parts and name those
4 P4 O P
1,2,3,-- as shown. 7 6 5 4 3 2 1
3. Take o-1 distance from op line P7
and draw an arc up to O1 radius
P5 P6
vector. Name the point P1
4. Similarly mark points P2, P3, P4
up to P8
And join those in a smooth curve. 5 7
It is a SPIRAL of one convolution.

6
Problem 28 SPIRAL
Point P is 80 mm from point O. It starts moving towards O and reaches it in two of
revolutions around.it Draw locus of point P (To draw a Spiral of TWO convolutions).
two convolutions
IMPORTANT APPROACH FOR CONSTRUCTION!
FIND TOTAL ANGULAR AND TOTAL LINEAR DISPLACEMENT
AND DIVIDE BOTH IN TO SAME NUMBER OF EQUAL PARTS.

2,10
P2

3,11 P1 1,9
SOLUTION STEPS: P3

Total angular displacement here

P10
is two revolutions And P9
Total Linear displacement here P11
is distance PO. 16 13 10 8 7 6 5 4 3 2 1 P
Just divide both in same parts i.e. 4,12
P4 P8 8,16
P12
Circle in EIGHT parts. P15

( means total angular displacement P13 P14

in SIXTEEN parts)
Divide PO also in SIXTEEN parts. P7
Rest steps are similar to the previous P5

problem.
P6
5,13 7,15

6,14
 HELIX
(UPON A CYLINDER)
PROBLEM: Draw a helix of one convolution, upon a cylinder. P8
Given 80 mm pitch and 50 mm diameter of a cylinder. 8
(The axial advance during one complete revolution is called P7
The pitch of the helix) 7
P6
6
P5
SOLUTION: 5
Draw projections of a cylinder.
Divide circle and axis in to same no. of equal parts. ( 8 ) 4 P4
Name those as shown.
3
Mark initial position of point ‘P’ P3
Mark various positions of P as shown in animation. 2 P2
Join all points by smooth possible curve.
Make upper half dotted, as it is going behind the solid 1 P1
and hence will not be seen from front side.
P
6

7 5

P 4

1 3

2
 HELIX
PROBLEM: Draw a helix of one convolution, upon a cone, P8 (UPON A CONE)
diameter of base 70 mm, axis 90 mm and 90 mm pitch.
(The axial advance during one complete revolution is called P7
The pitch of the helix)
P6

P5
SOLUTION:
Draw projections of a cone
Divide circle and axis in to same no. of equal parts. ( 8 ) P4
Name those as shown.
Mark initial position of point ‘P’ P3
Mark various positions of P as shown in animation.
Join all points by smooth possible curve. P2
Make upper half dotted, as it is going behind the solid
and hence will not be seen from front side. P1
X P Y

7 5

P6 P5
P7 P4
P 4
P8

P1 P3
1 3
P2
2
STEPS: Involute
DRAW INVOLUTE AS USUAL.
Method of Drawing
MARK POINT Q ON IT AS DIRECTED. Tangent & Normal
JOIN Q TO THE CENTER OF CIRCLE C.
CONSIDERING CQ DIAMETER, DRAW
A SEMICIRCLE AS SHOWN.
INVOLUTE OF A CIRCLE
MARK POINT OF INTERSECTION OF
THIS SEMICIRCLE AND POLE CIRCLE
AND JOIN IT TO Q. Q
THIS WILL BE NORMAL TO INVOLUTE.

DRAW A LINE AT RIGHT ANGLE TO

THIS LINE FROM Q.

IT WILL BE TANGENT TO INVOLUTE.

4
3
5
C 2
6
1
7
8
P
P8 1 2 3 4 5 6 7 8


D
STEPS:
DRAW CYCLOID AS USUAL. CYCLOID
MARK POINT Q ON IT AS DIRECTED.
Method of Drawing
WITH CP DISTANCE, FROM Q. CUT THE Tangent & Normal
POINT ON LOCUS OF C AND JOIN IT TO Q.

FROM THIS POINT DROP A PERPENDICULAR

ON GROUND LINE AND NAME IT N

JOIN N WITH Q.THIS WILL BE NORMAL TO

CYCLOID.

DRAW A LINE AT RIGHT ANGLE TO

THIS LINE FROM Q.

IT WILL BE TANGENT TO CYCLOID.

CYCLOID

C C1 C2 C3 C4 C5 C6 C7 C8

P N
D
 Spiral.
Method of Drawing
Tangent & Normal
SPIRAL (ONE CONVOLUSION.)
2

P2
3 1 Difference in length of any radius vectors
Q P1 Constant of the Curve =
Angle between the corresponding
radius vector in radian.
P3
OP – OP2 OP – OP2
= =
/2 1.57

4 P4 O P = 3.185 m.m.
7 6 5 4 3 2 1
P7 STEPS:
*DRAW SPIRAL AS USUAL.
P5 P6 DRAW A SMALL CIRCLE OF RADIUS EQUAL TO THE
CONSTANT OF CURVE CALCULATED ABOVE.

* LOCATE POINT Q AS DISCRIBED IN PROBLEM AND

5 7 THROUGH IT DRAW A TANGENTTO THIS SMALLER
CIRCLE.THIS IS A NORMAL TO THE SPIRAL.

*DRAW A LINE AT RIGHT ANGLE

6
*TO THIS LINE FROM Q.
IT WILL BE TANGENT TO CYCLOID.
Projection of point and line

engineering108.com
 NOTATIONS

FOLLOWING NOTATIONS SHOULD BE FOLLOWED WHILE NAMEING

DIFFERENT VIEWS IN ORTHOGRAPHIC PROJECTIONS.

OBJECT POINT A LINE AB

IT’S TOP VIEW a ab

IT’S FRONT VIEW a’ a’ b’

IT’S SIDE VIEW a” a” b”

SAME SYSTEM OF NOTATIONS SHOULD BE FOLLOWED

INCASE NUMBERS, LIKE 1, 2, 3 – ARE USED.

engineering108.com
 VP
2nd Quad. 1ST Quad.

Y
Observer

X Y HP
X

3rd Quad. 4th Quad.

THIS QUADRANT PATTERN,

IF OBSERVED ALONG X-Y LINE ( IN RED ARROW DIRECTION)
WILL EXACTLY APPEAR AS SHOWN ON RIGHT SIDE AND HENCE,
IT IS FURTHER USED TO UNDERSTAND ILLUSTRATION PROPERLLY.
engineering108.com
 PROJECTIONS OF A POINT IN FIRST QUADRANT.
POINT A ABOVE HP POINT A ABOVE HP POINT A IN HP
& INFRONT OF VP & IN VP & INFRONT OF VP
For Tv For Tv

PICTORIAL PICTORIAL For Tv

PRESENTATION A PRESENTATION
a’ a’
A Y
Y
Y a’
a
a
X a X X A

ORTHOGRAPHIC PRESENTATIONS
OF ALL ABOVE CASES.

Fv above xy, Fv above xy, Fv on xy,

Tv below xy. Tv on xy. Tv below xy.
VP VP VP

a’ a’

X Y X Y X
a’ Y
a

a a

HP HP
engineering108.com HP
 Point A is POINT A IN VP POINT A IN
ND
2 QUADRANT 1ST QUADRANT
Placed In VP a’
different A A
a’
quadrants
and it’s Fv & Tv a
are brought in HP OBSERVER
same plane for
Observer to see HP OBSERVER
clearly.
Fv is visible as
it is a view on a
VP. But as Tv is
is a view on Hp,
it is rotated
downward 900,
In clockwise
direction.The a
In front part of
Hp comes below
HP
xy line and the HP OBSERVER
OBSERVER
part behind Vp
comes above.
a
Observe and a’
note the A a’
process. POINT A IN A POINT A IN
3RD QUADRANT VP 4TH QUADRANT
VP

engineering108.com
 PROJECTIONS OF STRAIGHT LINES.
INFORMATION REGARDING A LINE means
IT’S LENGTH,
POSITION OF IT’S ENDS WITH HP & VP
IT’S INCLINATIONS WITH HP & VP WILL BE GIVEN.
AIM:- TO DRAW IT’S PROJECTIONS - MEANS FV & TV.

SIMPLE CASES OF THE LINE

1. A VERTICAL LINE ( LINE PERPENDICULAR TO HP & // TO VP)

2. LINE PARALLEL TO BOTH HP & VP.

3. LINE INCLINED TO HP & PARALLEL TO VP.

4. LINE INCLINED TO VP & PARALLEL TO HP.

5. LINE INCLINED TO BOTH HP & VP.

STUDY ILLUSTRATIONS GIVEN ON NEXT PAGE

SHOWING CLEARLY THE NATURE OF FV & TV
OF LINES LISTED ABOVE AND NOTE RESULTS.
engineering108.com
 For Tv Orthographic Pattern
Fv is a vertical line V.P. a’
a’
Showing True
A Length & Fv
1.
FV Tv is a point.
b’
A Line b’
perpendicular Y
X Y
to Hp B

& TV a b
Tv a b
// to Vp X

H.P.
Orthographic Pattern
For Tv V.P.
Fv & Tv both are
2. a’ Fv b’
b’
// to xy
A Line &
B
both show T. L.
// to Hp a’
& A Y X Y
// to Vp
b a b
Tv
X
a
H.P.
engineering108.com
 Fv inclined to xy V.P.
Tv parallel to xy.
3. b’ b’

A Line inclined to Hp B
a’ 
and  Y
parallel to Vp a’ X Y

A
a b
b T.V.
X
a

H.P.
Orthographic Projections

Tv inclined to xy V.P.
4. Fv parallel to xy.
a’ Fv b’
A Line inclined to Vp b’
and a’
parallel to Hp Ø
A B X Y
a Ø

Ø Tv
a b
b
engineering108.com
H.P.
 For Tv For Tv
5. A Line inclined to both
b’ Hp and Vp b’
(Pictorial presentation)
B
B

 Y
Y
On removal of object a’
a’ i.e. Line AB
Fv as a image on Vp. A
A Tv as a image on Hp, 
 X
X a T.V. b
a T.V. b
V.P.
b’
FV
a’ 

X Y
Orthographic Projections Note These Facts:-
Fv is seen on Vp clearly. Both Fv & Tv are inclined to xy.
To see Tv clearly, HP is a 
(No view is parallel to xy)
rotated 900 downwards, Both Fv & Tv are reduced
Hence it comes below xy. TV
lengths.
(No view shows True Length)
H.P. b
engineering108.com
 Orthographic Projections Note the procedure Note the procedure
Means Fv & Tv of Line AB When Fv & Tv known, When True Length is known,
are shown below, How to find True Length. How to locate Fv & Tv.
(Views are rotated to determine (Component a-1 of TL is drawn
with their apparent Inclinations
True Length & it’s inclinations which is further rotated
&
with Hp & Vp). to determine Fv)
V.P. V.P. V.P.
b’ b’ b 1’ b’ b1’

FV FV
TL 
a’  a’  a’  1’

X Y X Y X Y

1
a  b2 a Ø
a  TV 

TV TV

H.P. b H.P. b H.P. b b1

Here TV (ab) is not // to XY line In this sketch, TV is rotated Here a -1 is component

Hence it’s corresponding FV and made // to XY line. of TL ab1 gives length of Fv.
a’ b’ is not showing Hence it’s corresponding Hence it is brought Up to
True Length & FV a’ b1’ Is showing Locus of a’ and further rotated
True Length to get point b’. a’ b’ will be Fv.
True Inclination with Hp.
& Similarly drawing component
True engineering108.com
Inclination with Hp. of other TL(a’ b1‘) Tv can be drawn.
The most important diagram showing graphical relations 1) True Length ( TL) – a’ b1’ & a b
among all important parameters of this topic. 2) Angle of TL with Hp -  Important
TEN parameters
Study and memorize it as a CIRCUIT DIAGRAM 3) Angle of TL with Vp – Ø to be remembered
And use in solving various problems.
4) Angle of FV with xy –  with Notations

V.P. 5) Angle of TV with xy –  used here onward

Distance between
End Projectors. 6) LTV (length of FV) – Component (a-1)
b’ b1’
7) LFV (length of TV) – Component (a’-1’)
8) Position of A- Distances of a & a’ from xy
9) Position of B- Distances of b & b’ from xy
 10) Distance between End Projectors
a’  1’
LTV
NOTE this
X Y &  Construct with a’
a LFV 1 Ø& Construct with a
Ø
b’ & b1’ on same locus.

b & b1 on same locus.

Also Remember
b b1
H.P. True Length is never rotated. It’s horizontal component is
drawn & it is further rotated to locate view.

Views are always rotated, made horizontal & further

extended to locate TL,  & Ø
engineering108.com
 GROUP (A)
GENERAL CASES OF THE LINE INCLINED TO BOTH HP & VP
( based on 10 parameters).
PROBLEM
Line AB is 75 mm long and it is 300 &
400 Inclined to Hp & Vp respectively.
End A is 12mm above Hp and 10 mm b’ b’1
in front of Vp.
Draw projections. Line is in 1st quadrant.
FV
SOLUTION STEPS: TL
1) Draw xy line and one projector.
2) Locate a’ 12mm above xy line
& a 10mm below xy line. 
3) Take 300 angle from a’ & 400 from
a and mark TL I.e. 75mm on both a’
lines. Name those points b1’ and b1
respectively.
X Y
4) Join both points with a’ and a resp. a LFV
5) Draw horizontal lines (Locus) from Ø 1
both points.
6) Draw horizontal component of TL
a b1 from point b1 and name it 1.
( the length a-1 gives length of Fv as
we have seen already.) TV TL
7) Extend it up to locus of a’ and rotating
a’ as center locate b’ as shown.
Join a’ b’ as Fv.
8) From b’ drop a projector down ward
& get point b. Join a & b I.e. Tv. b b1
engineering108.com
PROBLEM :
Line AB 75mm long makes 450 inclination with Vp while it’s Fv makes 550.
End A is 10 mm above Hp and 15 mm in front of Vp.If line is in 1st quadrant
draw it’s projections and find it’s inclination with Hp. b’ b’1 LOCUS OF
Solution Steps:-
1.Draw x-y line.
2.Draw one projector for a’ & a
3.Locate a’ 10mm above x-y &
Tv a 15 mm below xy.
4.Draw a line 450 inclined to xy 550
from point a and cut TL 75 mm
on it and name that point b1
Draw locus from point b1
a’
5.Take 550 angle from a’ for Fv
above xy line. X y
6.Draw a vertical line from b1
up to locus of a and name it 1.
It is horizontal component of a LFV
TL & is LFV.
1
7.Continue it to locus of a’ and
rotate upward up to the line
of Fv and name it b’.This a’ b’
line is Fv.
8. Drop a projector from b’ on
locus from point b1 and
name intersecting point b.
Line a b is Tv of line AB.
9.Draw locus from b’ and from
a’ with TL distance cut point b1‘
10.Join a’ b1’ as TL and measure
it’s angle at a’. LOCUS OF b
It will be true angle of line with HP. engineering108.com b b1
PROBLEM - Fv of line AB is 500 inclined to xy and measures 55 mm long while it’s
Tv is 600 inclined to xy line. If end A is 10 mm above Hp and 15 mm in front of
Vp, draw it’s projections,find TL, inclinations of line with Hp & Vp.
b’ b’1

SOLUTION STEPS:
1.Draw xy line and one projector. 500
2.Locate a’ 10 mm above xy and 
a’
a 15 mm below xy line. X
3.Draw locus from these points. y
4.Draw Fv 500 to xy from a’ and a
mark b’ Cutting 55mm on it. 
600
5.Similarly draw Tv 600 to xy
from a & drawing projector from b’
Locate point b and join a b.
6.Then rotating views as shown,
locate True Lengths ab1 & a’b1’
and their angles with Hp and Vp.

b1
engineering108.com b
 PROBLEM :-
Line AB is 75 mm long .It’s Fv and Tv measure 50 mm & 60 mm long respectively.
End A is 10 mm above Hp and 15 mm in front of Vp. Draw projections of line AB
if end B is in first quadrant. Find angle with Hp and Vp.
b’ b’1

SOLUTION STEPS:
1.Draw xy line and one projector.
2.Locate a’ 10 mm above xy and
a 15 mm below xy line.
3.Draw locus from these points.
4.Cut 60mm distance on locus of a’  LTV 1’
a’
& mark 1’ on it as it is LTV.
5.Similarly Similarly cut 50mm on X Y
locus of a and mark point 1 as it is LFV.
6.From 1’ draw a vertical line upward a LFV
1
and from a’ taking TL ( 75mm ) in 
compass, mark b’1 point on it.
Join a’ b’1 points.
7. Draw locus from b’1
8. With same steps below get b1 point
and draw also locus from it.
9. Now rotating one of the components
I.e. a-1 locate b’ and join a’ with it
 & 
to get Fv.
b1
10. Locate tv similarly and measure b
engineering108.com
Angles
PROBLEM :-
T.V. of a 75 mm long Line CD, measures 50 mm.
End C is in Hp and 50 mm in front of Vp.
End D is 15 mm in front of Vp and it is above Hp.
d’ d’1 LOCUS OF d’ & d’1
Draw projections of CD and find angles with Hp and Vp.

SOLUTION STEPS:
1.Draw xy line and one projector.
2.Locate c’ on xy and
c 50mm below xy line.
3.Draw locus from these points.
4.Draw locus of d 15 mm below xy c’ 
5.Cut 50mm & 75 mm distances X on Y
locus of d from c and mark points d d1 LOCUS OF d & d1
d & d1 as these are Tv and line CD
lengths resp.& join both with c.
6.From d1 draw a vertical line upward
up to xy I.e. up to locus of c’ and
draw an arc as shown.
 &  from d to
7 Then draw one projector
meet this arc in d’ point & join c’ d’ 
8. Draw locus of d’ and cut 75 mm c
on it from c’ as TL
9.Measure Angles
engineering108.com
 GROUP (B)
PROBLEMS INVOLVING TRACES OF THE LINE.

TRACES OF THE LINE:-

THESE ARE THE POINTS OF INTERSECTIONS OF A LINE ( OR IT’S EXTENSION )

WITH RESPECTIVE REFFERENCE PLANES.

A LINE ITSELF OR IT’S EXTENSION, WHERE EVER TOUCHES H.P.,

THAT POINT IS CALLED TRACE OF THE LINE ON H.P.( IT IS CALLED H.T.)

SIMILARLY, A LINE ITSELF OR IT’S EXTENSION, WHERE EVER TOUCHES V.P.,

THAT POINT IS CALLED TRACE OF THE LINE ON V.P.( IT IS CALLED V.T.)

V.T.:- It is a point on Vp.

Hence it is called Fv of a point in Vp.
Hence it’s Tv comes on XY line.( Here onward named as v )
H.T.:- It is a point on Hp.
Hence it is called Tv of a point in Hp.
Hence it’s Fv comes on XY line.( Here onward named as ’h’ )
engineering108.com
 b’

STEPS TO LOCATE HT.

(WHEN PROJECTIONS ARE GIVEN.)
1. Begin with FV. Extend FV up to XY line. a’
2. Name this point h’ v h’
( as it is a Fv of a point in Hp) x y
3. Draw one projector from h’.
4. Now extend Tv to meet this projector. VT’ HT
This point is HT a

STEPS TO LOCATE VT.

(WHEN PROJECTIONS ARE GIVEN.) Observe & note :-
1. Points h’ & v always on x-y line. b

1. Begin with TV. Extend TV up to XY line.

2. VT’ & v always on one projector.
2. Name this point v
( as it is a Tv of a point in Vp) 3. HT & h’ always on one projector.

3. Draw one projector from v. 4. FV - h’- VT’ always co-linear.

4. Now extend Fv to meet this projector.
This point is VT 5. TV - v - HT always co-linear.

engineering108.com
PROBLEM :- Fv of line AB makes 450 angle
with XY line and measures 60 mm.
Line’s Tv makes 300 with XY line. End A is 15
mm above Hp and it’s VT is 10 mm b’1
below Hp. Draw projections of line
b’
AB,determine inclinations with Hp & Vp and
locate HT, VT.

SOLUTION STEPS:-
Draw xy line, one projector and
a’ 
450

locate fv a’ 15 mm above xy. 15

Take 450 angle from a’ and x v h’ y
marking 60 mm on it locate point 10b’. 300
Draw locus of VT, 10 mm below xy
VT’
& extending Fv to this locus locate VT. a
as fv-h’-vt’ lie on one st.line. 
Draw projector from vt, locate v on xy.
From v take 300 angle downward as
Tv and it’s inclination can begin with v. b
Draw projector from b’ and locate b I.e.Tv point. b1
Now rotating views as usual TL and
it’s inclinations can be found.
Name extension of Fv, touching xy as h’
and below it, on extension of Tv, locate HT.
engineering108.com
 PROBLEM
One end of line AB is 10mm above Hp and
other end is 100 mm in-front of Vp.
It’s Fv is 450 inclined to xy while it’s HT & VT b’
are 45mm and 30 mm below xy respectively. b’1 LOCUS OF b’ & b’1
Draw projections and find TL with it’s
inclinations with Hp & VP.

a’ 450

10 v h’
X Y
30
SOLUTION STEPS:- 45
Draw xy line, one projector and VT’ HT
locate a’ 10 mm above xy.
Draw locus 100 mm below xy for points b & b1 100
Draw loci for VT and HT, 30 mm & 45 mm a

below xy respectively.
Take 450 angle from a’ and extend that line backward
to locate h’ and VT, & Locate v on xy above VT.
Locate HT below h’ as shown.
Then join v – HT – and extend to get top view end b.
b b1 LOCUS OF b & b1
Draw projector upward and locate b’ Make a b & a’b’ dark.
Now as usual rotating views find TL and it’s inclinations.
engineering108.com
 Instead of onsidering a & a’ as proje tions of first point,
if & VT’ are onsidered as first point , then true in linations of line ith
Hp & Vp i.e. angles  &  an e onstru ted ith points VT’ & V respe ti ely.

b’ b1’

Then from point v & HT

a’
angles  &  can be drawn.
X v &

Y
From point VT’ & h’
angles  &  can be drawn.

VT’

b engineering108.com
b
1
PROBLEM :-
Line AB 100 mm long is 300 and 450 inclined to Hp & Vp respectively. b1’
b’
End A is 10 mm above Hp and it’s VT is 20 mm below Hp
.Draw projections of the line and it’s HT.
FV

Locus of a & a1’ a’ a1’

SOLUTION STEPS:- 10
X v h’
Draw xy, one projector Y
(45 )
0
and locate on it VT and V. 20
Draw locus of a’ 10 mm above xy.  (300)
Take 300 from VT and draw a line. VT’
Where it intersects with locus of a’ HT
name it a1’ as it is TL of that part.
From a1’ cut 100 mm (TL) on it and locate point b1’ a a1
0
Now from v take 45 and draw a line downwards
& Mark on it distance VT-a1’ I.e.TL of extension & name it a1
Extend this line by 100 mm and mark point b1. TV
Draw it’s component on locus of VT’
& further rotate to get other end of Fv i.e.b’
Join it with VT’ and mark intersection point
(with locus of a1’ ) and name it a’ b1
Now as usual locate points a and b and h’ and HT. b

engineering108.com
PROBLEM :-
A line AB is 75 mm long. It’s Fv & Tv make
450 and 600 inclinations with X-Y line resp b1’
b’
End A is 15 mm above Hp and VT is 20 mm
below Xy line. Line is in first quadrant.
Draw projections, find inclinations with Hp & FV
Vp. Also locate HT.
Locus of a & a1’ a’ a1’

15
X v h’
Y
600
20 

450
VT’
SOLUTION STEPS:- HT
Similar to the previous only change
is instead of line’s inclinations, a a1
views inclinations are given.
So first take those angles from VT & v TV
Properly, construct Fv & Tv of extension,
then determine it’s TL( V-a1)
and on it’s extension mark TL of line
b1
and proceed and complete it. engineering108.com b
PROBLEM :- The projectors drawn from VT & end A of line AB are 40mm apart.
End A is 15mm above Hp and 25 mm in front of Vp. VT of line is 20 mm below Hp.
If line is 75mm long, draw it’s projections, find inclinations with HP & Vp

b’ b1’

a’ a1 ’

15
Draw two projectors for VT & end A X v Y
Locate these points and then
20 
25 
VT’
a

40mm
b b1

engineering108.com
 GROUP (C)
CASES OF THE LINES IN A.V.P., A.I.P. & PROFILE PLANE.

b’ Line AB is in AIP as shown in above figure no 1.

It’s FV (a’b’) is shown projected on Vp.(Looking in arrow direction)
Here one can clearly see that the
Inclination of AIP with HP = Inclination of FV with XY line
a’ 


A A.V.P.

Line AB is in AVP as shown in above figure no 2.. 

a b
It’s TV (a b) is shown projected on Hp.(Looking in arrow direction)
Here one can clearly see that the
Inclination of AVP with VP = Inclination of TV with XY line

engineering108.com
LINE IN A PROFILE PLANE ( MEANS IN A PLANE PERPENDICULAR TO BOTH HP & VP)
For T.V.

ORTHOGRAPHIC PATTERN OF LINE IN PROFILE PLANE

VP VT PP
a’ a”
A a’

FV LSV

b’ b’ b”
X Y
HT

a
B
TV
a
b
b HP

Results:-
1. TV & FV both are vertical, hence arrive on one single projector.
2. It’s Side View shows True Length ( TL)
3. Sum of it’s inclinations with HP & VP equals to 900 (  +  = 900 )
4. It’s HT & VT arrive on same projector and can be easily located
From Side View.

engineering108.com
PROBLEM - Line AB 80 mm long, makes 300 angle with Hp
and lies in an Aux.Vertical Plane 450 inclined to Vp.
End A is 15 mm above Hp and VT is 10 mm below X-y line.
Draw projections, fine angle with Vp and Ht. b’ Locus of b’ b1’

Locus of a’ & a1’ a’ a 1’

15 v h’
X 450 Y
10 

VT HT

Simply consider inclination of AVP AVP 450 to VP

as inclination of TV of our line,

well then? Locus of b’
b b1

engineering108.com
 PROBLEM :- A line AB, 75mm long, has one end A in Vp. Other end B is 15 mm above Hp
and 50 mm in front of Vp.Draw the projections of the line when sum of it’s
Inclinations with HP & Vp is 900, means it is lying in a profile plane.
Find true angles with ref.planes and it’s traces.

SOLUTION STEPS:-
After drawing xy line and one projector
Locate top view of A I.e point a on xy as VT (VT) a”
a’
It is in Vp,
Side View
Locate Fv of B i.e.b’15 mm above xy as Front view ( True Length )

VP
it is above Hp.and Tv of B i.e. b, 50 mm
b’ b”
below xy asit is 50 mm in front of Vp
a  (HT)
Draw side view structure of Vp and Hp X HP Y
and locate S.V. of point B i.e. b’’
From this point cut 75 mm distance on Vp and
Mark a’’ as A is in Vp. (This is also VT of line.) top view
From this point draw locus to left & get a’
Extend SV up to Hp. It will be HT. As it is a Tv b
Rotate it and bring it on projector of b.
Now as discussed earlier SV gives TL of line HT
and at the same time on extension up to Hp & Vp
gives inclinations with those panes.

engineering108.com
 APPLICATIONS OF PRINCIPLES OF PROJECTIONS OF LINES
IN SOLVING CASES OF DIFFERENT PRACTICAL SITUATIONS.

In these types of problems some situation in the field

or
some object will be described .
It’s relation with Ground ( HP )
And
a Wall or some vertical object ( VP ) will be given.

Indirectly information regarding Fv & Tv of some line or lines,

inclined to both reference Planes will be given
and
you are supposed to draw it’s projections
and
further to determine it’s true Length and it’s inclinations with ground.

Here various problems along with

actual pictures of those situations are given CHECK YOUR ANSWERS
for you to understand those clearly. WITH THE SOLUTIONS
Now looking for views in given ARROW directions, GIVEN IN THE END.
YOU are supposed to draw projections & find answers, ALL THE BEST !!
Off course you must visualize the situation properly.
engineering108.com
PROBLEM --Two objects, a flower (A) and an orange (B) are within a rectangular compound wall,
whose P & Q are walls meeting at 900. Flower A is 1M & 5.5 M from walls P & Q respectively.
Orange B is 4M & 1.5M from walls P & Q respectively. Drawing projection, find distance between them
If flower is 1.5 M and orange is 3.5 M above the ground. Consider suitable scale..
TV

B Wall Q

FV
engineering108.com
PROBLEM :- Two mangos on a tree A & B are 1.5 m and 3.00 m above ground
and those are 1.2 m & 1.5 m from a 0.3 m thick wall but on opposite sides of it.
If the distance measured between them along the ground and parallel to wall is 2.6 m,
Then find real distance between them by drawing their projections.

TV

0.3M THICK
A

engineering108.com
PROBLEM -oa, ob & oc are three lines, 25mm, 45mm and 65mm
long respectively.All equally inclined and the shortest
is vertical.This fig. is TV of three rods OA, OB and OC
whose ends A,B & C are on ground and end O is 100mm
above ground. Draw their projections and find length of
each along with their angles with ground.

TV

C
A

FV
45 mm

engineering108.com
PROBLEM : A person observes two objects, A & B, on the ground, from a tower, 15 M high,
At the angles of depression 300 & 450. Object A is is due North-West direction of observer and
object B is due West direction. Draw projections of situation and find distance of objects from
observer and from tower also.

O
300

450

A
S

B
engineering108.com
W
PROBLEM :-Guy ropes of two poles fixed at 4.5m and 7.5 m above ground,
are attached to a corner of a building 15 M high, make 300 and 450 inclinations
with ground respectively.The poles are 10 M apart. Determine by drawing their
projections,Length of each rope and distance of poles from building.

TV

15 M

A 300

4.5 M

450

7.5M

engineering108.com
PROBLEM :- A tank of 4 M height is to be strengthened by four stay rods from each corner
by fixing their other ends to the flooring, at a point 1.2 M and 0.7 M from two adjacent walls respectively,
as shown. Determine graphically length and angle of each rod with flooring.

TV

4M

engineering108.com
PROBLEM :- A horizontal wooden platform 2 M long and 1.5 M wide is supported by four chains
from it’s corners and chains are attached to a hook 5 M above the center of the platform.
Draw projections of the objects and determine length of each chain along with it’s inclination with ground.

TV
Hook H

A C

B
engineering108.com
PROBLEM :-
A PICTURE FRAME 2 M WIDE AND 1 M TALL IS RESTING ON HORIZONTAL WALL RAILING
MAKES 350 INCLINATION WITH WALL. IT IS ATTAACHED TO A HOOK IN THE WALL BY TWO STRINGS.
THE HOOK IS 1.5 Ma ABOVE WALL RAILING. DETERMINE LENGTH OF EACH CHAIN AND TRUE ANGLE BETWEEN THEM

350

Wall railing

engineering108.com
 Thank You

For more tutorials on engineering subjects visit is at engineering108.com

engineering108.com
 PROJECTIONS OF PLANES

A plane is a two dimensional object having length and breadth only. Its
thickness is always neglected. Various shapes of plane figures are
considered such as square, rectangle, circle, pentagon, hexagon, etc.
 PROJECTIONS OF PLANES
In this topic various plane figures are the objects.

What is usually asked in the problem?

To draw their projections means F.V, T.V. & S.V.

What will be given in the problem?

1. Description of the plane figure.
2. It’s position with HP and VP.

In which manner it’s position with HP & VP will be described?

1.Inclination of it’s SURFACE with one of the reference planes will be given.
2. Inclination of one of it’s EDGES with other reference plane will be given
(Hence this will be a case of an object inclined to both reference Planes.)
Study the illustration showing
surface & side inclination given on next page.
 CASE OF A RECTANGLE – OBSERVE AND NOTE ALL STEPS.

SURFACE PARALLEL TO HP SURFACE INCLINED TO HP ONE SMALL SIDE INCLINED TO VP

PICTORIAL PRESENTATION PICTORIAL PRESENTATION PICTORIAL PRESENTATION

ORTHOGRAPHIC ORTHOGRAPHIC ORTHOGRAPHIC

TV-True Shape FV- Inclined to XY FV- Apparent Shape
FV- Line // to xy TV- Reduced Shape TV-Previous Shape
VP
VP VP
d1’ c1’

a’ d’ a1’ b1’
b’ c’

a d a1 d1

b c b1 c1
HP A HP B HP
C
Problem 1: Read problem and answer following questions
Rectangle 30mm and 50mm 1. Surface inclined to which plane? ------- HP
sides is resting on HP on one 2. Assumption for initial position? ------// to HP
small side which is 300 inclined 3. So which view will show True shape? --- TV
to VP,while the surface of the 4. Which side will be vertical? ---One small side.
plane makes 450 inclination with Hence begin with TV, draw rectangle below X-Y
HP. Draw it’s projections. drawing one small side vertical.

Surface // to Hp Surface inclined to Hp

d’c’ c’1 d’1
c’d’
a’b’
a’ b’ 450 b’1 a’1 Y
X 300
a d a1 d1 Side
Inclined
to Vp

b c b1 c1
Problem 2: Read problem and answer following questions
A 300 – 600 set square of longest side 1 .Surface inclined to which plane? ------- VP
100 mm long, is in VP and 300 inclined 2. Assumption for initial position? ------// to VP
to HP while it’s surface is 450 inclined 3. So which view will show True shape? --- FV
to VP.Draw it’s projections 4. Which side will be vertical? ------longest side.

(Surface & Side inclinations directly given)

Hence begin with FV, draw triangle above X-Y
keeping longest side vertical.
a’ a’1

c’ c’1
side inclined to Hp
c’1

a’1

b’1
b’1
b’
300
X a
b 450 a1 b1 Y
a c
b c1
c
Surface // to Vp Surface inclined to Vp
Problem 3: Read problem and answer following questions
A 300 – 600 set square of longest side 1 .Surface inclined to which plane? ------- VP
100 mm long is in VP and it’s surface 2. Assumption for initial position? ------// to VP
450 inclined to VP. One end of longest 3. So which view will show True shape? --- FV
side is 10 mm and other end is 35 mm 4. Which side will be vertical? ------longest side.
above HP. Draw it’s projections
Hence begin with FV, draw triangle above X-Y
(Surface inclination directly given.
Side inclination indirectly given) keeping longest side vertical.

First TWO steps are similar to previous problem.

Note the manner in which side inclination is given.
a’ a’1 End A 35 mm above Hp & End B is 10 mm above Hp.
So redraw 2nd Fv as final Fv placing these ends as said.
c’ c’1
c’1

a’1

35
b’1
b’1
b’
X 10 Y
a a1
b 450 b1
a c
b c1
c
Problem 4: Read problem and answer following questions
A regular pentagon of 30 mm sides is 1. Surface inclined to which plane? ------- HP
resting on HP on one of it’s sides with it’s 2. Assumption for initial position? ------ // to HP
surface 450 inclined to HP. 3. So which view will show True shape? --- TV
Draw it’s projections when the side in HP 4. Which side will be vertical? -------- any side.
makes 300 angle with VP Hence begin with TV,draw pentagon below
SURFACE AND SIDE INCLINATIONS X-Y line, taking one side vertical.
ARE DIRECTLY GIVEN.
d’ d’1
c’e’
e’1 c’1
b’ a’
X b’ a’ c’e’ d’ b’1 Y
450 a’1
a1 300
e e1
e1
a a1 b1

d1
d
d1 c1
b b1

c c1
 Problem 5: Read problem and answer following questions
A regular pentagon of 30 mm sides is resting 1. Surface inclined to which plane? ------- HP
on HP on one of it’s sides while it’s opposite 2. Assumption for initial position? ------ // to HP
vertex (corner) is 30 mm above HP. 3. So which view will show True shape? --- TV
Draw projections when side in HP is 300 4. Which side will be vertical? --------any side.
inclined to VP. Hence begin with TV,draw pentagon below
SURFACE INCLINATION INDIRECTLY GIVEN X-Y line, taking one side vertical.
SIDE INCLINATION DIRECTLY GIVEN:

ONLY CHANGE is
the manner in which surface inclination is described:
One side on Hp & it’s opposite corner 30 mm above Hp. d’ d’1
Hence redraw 1st Fv as a 2nd Fv making above arrangement.
Keep a’b’ on xy & d’ 30 mm above xy. c’e’ c’1
30 e’1

b’ a’ c’e’ d’ a’
X b’ a’1 b’1 Y
300
e1 a1
e
e1
a a1 b1

d d1
d1 c1
b b1

c c1
 c’1
b’1
Problem 8: A circle of 50 mm diameter is a’ b’ d’ c’
resting on Hp on end A of it’s diameter AC 300 a’1 d’1 Y
X
which is 300 inclined to Hp while it’s Tv d1
450
d
is 450 inclined to Vp.Draw it’s projections.

a ca c1
1

Read problem and answer following questions

1. Surface inclined to which plane? ------- HP b b1
2. Assumption for initial position? ------ // to HP
3. So which view will show True shape? --- TV The difference in these two problems is in step 3 only.
4. Which diameter horizontal? ---------- AC In problem no.8 inclination of Tv of that AC is
Hence begin with TV,draw rhombus below given,It could be drawn directly as shown in 3rd step.
X-Y line, taking longer diagonal // to X-Y While in no.9 angle of AC itself i.e. it’s TL, is
given. Hence here angle of TL is taken,locus of c1
Is drawn and then LTV I.e. a1 c1 is marked and
final TV was completed.Study illustration carefully.
Problem 9: A circle of 50 mm diameter is
resting on Hp on end A of it’s diameter AC
which is 300 inclined to Hp while it makes c’1
450 inclined to Vp. Draw it’s projections. b’1
a’ b’ d’ c’
a’1 d’1
d d1
300
Note the difference in
a ca c1
construction of 3rd step 1

in both solutions.
b b1
 Read problem and answer following questions
Problem 10: End A of diameter AB of a circle is in HP 1. Surface inclined to which plane? ------- HP
and end B is in VP.Diameter AB, 50 mm long is 2. Assumption for initial position? ------ // to HP
300 & 600 inclined to HP & VP respectively. 3. So which view will show True shape? --- TV
Draw projections of circle. 4. Which diameter horizontal? ---------- AB
Hence begin with TV,draw CIRCLE below
X-Y line, taking DIA. AB // to X-Y

The problem is similar to previous problem of circle – no.9.

But in the 3rd step there is one more change.
Like 9th problem True Length inclination of dia.AB is definitely expected
but if you carefully note - the the SUM of it’s inclinations with HP & VP is 900.
Means Line AB lies in a Profile Plane.
Hence it’s both Tv & Fv must arrive on one single projector.
So do the construction accordingly AND note the case carefully..

300
X Y
600
SOLVE SEPARATELY
ON DRAWING SHEET
GIVING NAMES TO VARIOUS
POINTS AS USUAL,
AS THE CASE IS IMPORTANT
 Problem 11: Read problem and answer following questions
A hexagonal lamina has its one side in HP and 1. Surface inclined to which plane? ------- HP
Its apposite parallel side is 25mm above Hp and 2. Assumption for initial position? ------ // to HP
In Vp. Draw it’s projections.
Take side of hexagon 30 mm long.
3. So which view will show True shape? --- TV
4. Which diameter horizontal? ---------- AC
Hence begin with TV,draw rhombus below
X-Y line, taking longer diagonal // to X-Y
ONLY CHANGE is the manner in which surface inclination
is described:
One side on Hp & it’s opposite side 25 mm above Hp.
Hence redraw 1st Fv as a 2nd Fv making above arrangement.
Keep a’b’ on xy & d’e’ 25 mm above xy.

e’1 d’1

25 f’1 c1’
X a’b’ c’ f’ d’e’ a’1 b’1 Y
f f1 e1 d1
f1 c1
a e a1 e1
a1 b1 As 3rd step
b d b1 d1 redraw 2nd Tv keeping
c1
side DE on xy line.
c
Because it is in VP
as said in problem.
 FREELY SUSPENDED CASES.
IMPORTANT POINTS
1.In this case the plane of the figure always remains perpendicular to Hp.
Problem 12: 2.It may remain parallel or inclined to Vp.
An isosceles triangle of 40 mm long 3.Hence TV in this case will be always a LINE view.
base side, 60 mm long altitude Is 4.Assuming surface // to Vp, draw true shape in suspended position as FV.
freely suspended from one corner of (Here keep line joining point of contact & centroid of fig. vertical )
Base side.It’s plane is 450 inclined to 5.Always begin with FV as a True Shape but in a suspended position.
Vp. Draw it’s projections. AS shown in 1st FV.

a’1
a’
C

b’1
b’ g’ g’1
H
G c’ c’1
H/3
X Y

A B

b a,g c 450
First draw a given triangle
With given dimensions,
Locate it’s centroid position
And Similarly solve next problem
join it with point of suspension. of Semi-circle
 IMPORTANT POINTS
Problem 13 1.In this case the plane of the figure always remains perpendicular to Hp.
:A semicircle of 100 mm diameter 2.It may remain parallel or inclined to Vp.
is suspended from a point on its 3.Hence TV in this case will be always a LINE view.
straight edge 30 mm from the midpoint 4.Assuming surface // to Vp, draw true shape in suspended position as FV.
of that edge so that the surface makes (Here keep line joining point of contact & centroid of fig. vertical )
an angle of 450 with VP. 5.Always begin with FV as a True Shape but in a suspended position.
Draw its projections. AS shown in 1st FV.

A
a’
20 mm
p’
P

G b’
CG g’

c’

e’
d’
X Y

First draw a given semicircle

With given diameter,
Locate it’s centroid position b c a p,g d e
And
join it with point of suspension.
 To determine true shape of plane figure when it’s projections are given.
BY USING AUXILIARY PLANE METHOD
WHAT WILL BE THE PROBLEM?
Description of final Fv & Tv will be given.
You are supposed to determine true shape of that plane figure.

Follow the below given steps:

1. Draw the given Fv & Tv as per the given information in problem.
2. Then among all lines of Fv & Tv select a line showing True Length (T.L.)
(It’s other view must be // to xy)
3. Draw x1-y1 perpendicular to this line showing T.L.
4. Project view on x1-y1 ( it must be a line view)
5. Draw x2-y2 // to this line view & project new view on it.
It will be the required answer i.e. True Shape.

The facts you must know:-

If you carefully study and observe the solutions of all previous problems,
You will find
IF ONE VIEW IS A LINE VIEW & THAT TOO PARALLEL TO XY LINE,
THEN AND THEN IT’S OTHER VIEW WILL SHOW TRUE SHAPE:

NOW FINAL VIEWS ARE ALWAYS SOME SHAPE, NOT LINE VIEWS:
SO APPLYING ABOVE METHOD:
Study Next
WE FIRST CONVERT ONE VIEW IN INCLINED LINE VIEW .(By using x1y1 aux.plane) Four Cases
THEN BY MAKING IT // TO X2-Y2 WE GET TRUE SHAPE.
 Problem 14 Tv is a triangle abc. Ab is 50 mm long, angle cab is 300 and angle cba is 650.
a’b’c’ is a Fv. a’ is 25 mm, b’ is 40 mm and c’ is 10 mm above Hp respectively. Draw projections
of that figure and find it’s true shape.
As per the procedure-
1.First draw Fv & Tv as per the data.
2.In Tv line ab is // to xy hence it’s other view a’b’ is TL. So draw x1y1 perpendicular to it.
3.Project view on x1y1.
a) First draw projectors from a’b’ & c’ on x1y1.
b) from xy take distances of a,b & c( Tv) mark on these projectors from x1y1. Name points a1b1 & c1.
c) This line view is an Aux.Tv. Draw x2y2 // to this line view and project Aux. Fv on it.
for that from x1y1 take distances of a’b’ & c’ and mark from x2y= on new projectors.
4.Name points a’1 b’1 & c’1 and join them. This will be the required true shape.
Y1
a1b1 Y
2

b’ b’1
15
a’

15
C1
10 C’ X1
X X2 a’1
Y
c c’1

ALWAYS FOR NEW FV TAKE

DISTANCES OF PREVIOUS FV
300 650 AND FOR NEW TV, DISTANCES
a OF PREVIOUS TV
b
50 mm REMEMBER!!
PROBLEM 15: Fv & Tv both are circles of 50 mm diameter. Determine true shape of an elliptical plate.

ADOPT SAME PROCEDURE.

a c is considered as line // to xy.
Then a’c’ becomes TL for the purpose.
Using steps properly true shape can be
50D y1
Easily determined. b’ b1 y2
Study the illustration.
TL ac1 1
a’ c’ b’1
c’1
d’ d
X1 1
X d Y
X2

ALWAYS, FOR NEW FV

a’1
TAKE DISTANCES OF d’1
PREVIOUS FV AND a c TRUE SHAPE
FOR NEW TV, DISTANCES
OF PREVIOUS TV
REMEMBER!! 50 D. b
 Problem 16 : Draw a regular pentagon of
30 mm sides with one side 300 inclined to xy.
This figure is Tv of some plane whose Fv is
A line 450 inclined to xy.
Determine it’s true shape. b1
a1
c1
IN THIS CASE ALSO TRUE LENGTH
IS NOT AVAILABLE IN ANY VIEW. X1

BUT ACTUALLY WE DONOT REQUIRE

TL TO FIND IT’S TRUE SHAPE, AS ONE a’ e1 d1
VIEW (FV) IS ALREADY A LINE VIEW.
SO JUST BY DRAWING X1Y1 // TO THIS b’
VIEW WE CAN PROJECT VIEW ON IT e’
AND GET TRUE SHAPE:
c’ Y1
d’
STUDY THE ILLUSTRATION.. 450
X 300 Y
e

d
ALWAYS FOR NEW FV a
TAKE DISTANCES OF
PREVIOUS FV AND FOR
NEW TV, DISTANCES OF
PREVIOUS TV c
REMEMBER!! b
 Unit III-Projection of Solids
1. A right pentagonal pyramid side of side of base 30 mm and height 60mm rests on one of its base
on HP ;the base being lifted up until higher corner in it is 40 mm above HP .draw the projection
when the edge on which it rests is made perpendicular to VP.(January 2009)
2. A cylinder of base diameter 60mm and height 80 mm is resting on HP in one of its generators
with its axis inclined at 50° to VP.draw its projections.(January 2009).
3. A cone of 30 mm diameter and 70 mm height rests on the ground on one of its base circle point
such that apex is 20mm and the nearest base is perpendicular to HP.dra its projections. (January
2009)
4. Draw the projections of square prism of size 30mm x 60mm with a diagonal vertical. (January
2009)
5. A cone 30 mm diameter and 70 mm height rests on ground on one of its base circle point such
that apex is 20 mm and the nearest base circle point is 50mm in front of VP and the base is
perpendicular to HP. draw the projections.(January 2009).
6. Draw the projection of a square [prism of size 30 mm x 60 mm with a solid diagonal vertical
(January 2009).
7. A hexagonal pyramid of base side 30mm and axis length 60mm is resting on HP on one of its
base corner with the base sides containing the corner equally inclined to HP and its axis parallel
to both HP and VP.draw the projections.(January 2009)
8. A tetrahedron of side 50 mm is resting on VP on one of its edges with the face containing that
edge is perpendicular to both HP and VP. Draw its projections. (January 2010)
9. Draw the projection of hexagonal prism whose one rectangular face is 25mm x 65 mm resting
on HP on one of its base corners such that the other extreme corner is 30mm above HP with the
axis parallel to VP.(January 2011)
10. A hexagonal pyramid of base 25 mm and axis 60 mm long is freely suspended from a corner of
the base. Draw the projections.(January 2011)
11. A right hexagonal pyramid, edge of base 25mm and height 50 mm, rests on one of its base on
HP with its axis parallel to VP. draw the projections of the pyramid hen its base make an angle of
45° to the HP.(January 2012)
12. A pentagonal prism, side of base 25 mm and axis 50 mm long, rests with one of its shorter edges
on HP such that the base containing that edge makes an angle of 30° to HP and its axis parallel
to VP. Draw its projections (January 2013).
13. Draw the projections of a hexagonal prism of base side 20mm and axis length 50mm when its
rests on the ground on one of the edges of the base and the axis inclined at 35° to the ground
and parallel to the VP.(January 2013)
14. Draw the projections of pentagonal pyramid of base side 30mm and altitude 60 mm when it
rests on the ground on one of its base sides with the axis inclined at 30° to the ground and
parallel to the VP.Use change of reference line method. (January 2013)
15. A square pyramid of base side 40 mm and height 60 mm is resting on HP on one of its triangular
faces such that axis is inclined to HP and parallel to VP. Draw its projection using auxiliary plane
method(January 2014).
ORTHOGRAPHIC
PROJECTION

AN
INTRODUCTION
Orthographic Projections

• Orthographic Projections are a collection of

2-D drawings that work together to give an
accurate overall representation of an object.
Defining the
Six Principal
Views or
Orthographic
Views
Which Views to Present?
General Guidelines
• Pick a Front View that is most descriptive
of object
• Normally the longest dimension is chosen
as the width (or depth)
• Most common combination of views is to
use:
– Front, Top, and Side View
 Glass Box Approach

• Place the object in a glass box

• Freeze the view from each direction (each

of the six sides of the box) and unfold the
box
Glass Box Approach
Glass Box Approach
Glass Box Approach
Glass Box Approach
Glass Box Approach
Glass Box Approach
First and Third Angle Projections

Third-angle Projection

First-angle Projection

• First Angle
• Third Angle
Conventional Orthographic Views
Width

Top Depth
View/Plan

Right
Front View Side Height
View
Lines on an engineering drawing signify more than just the geometry of the object and it is
important that the appropriate line type is used.

Line Thickness

For most engineering drawings you will require two thickness', a thick and thin line.
The general recommendation are that thick lines are twice as thick as thin lines.

A thick continuous line is used for visible

edges and outlines.
A thin line is used for hatching, leader
lines, short centre lines, dimensions and
projections.
Line Styles

Other line styles used to clarify important features on drawings are:

Thin chain lines are a common feature on engineering drawings used to

indicate centre lines. Centre lines are used to identify the centre of a circle,
cylindrical features, or a line of symmetry.
Dashed lines are used to show important hidden detail for example wall
thickness and holes..
Precedence of Lines
• Visible lines takes precedence over all
other lines
0.6 mm

• Hidden lines and cutting plane lines take

precedence over center lines
0.3 mm

• Center lines have lowest precedence

0.6 mm
For Example:

1. Visible
2. Hidden
3. Center
 Dimensioning
A dimensioned drawing should provide all the information necessary for a finished product or
part to be manufactured. An example dimension is shown below.

Dimensions are always drawn using continuous thin lines. Two projection lines indicate
where the dimension starts and finishes. Projection lines do not touch the object and are
drawn perpendicular to the element you are dimensioning.
All dimensions less than 1 should have a leading zero. i.e. .35 should be written as 0.35
 Types of Dimensioning

• Parallel Dimensioning
• Parallel dimensioning consists of several
dimensions originating from one projection
line.
•Superimposed Running Dimensions

•Superimposed running dimensioning simplifies parallel

dimensions in order to reduce the space used on a drawing.
The common origin for the dimension lines is indicated by a
small circle at the intersection of the first dimension and the
projection line.
•Chain Dimensioning

•Combined Dimensions
A combined dimension uses both chain and parallel dimensioning.
 Dimensioning of circles

• (a) shows two common methods of dimensioning a circle. One method

dimensions the circle between two lines projected from two diametrically
opposite points. The second method dimensions the circle internally.

• (b) is used when the circle is too small for the dimension to be easily read if
it was placed inside the circle.
 Dimensioning Radii

• All radial dimensions are proceeded by the capital R.

(a) shows a radius dimensioned with the centre of the radius located on the drawing.

(b) shows how to dimension radii which do not need their centres locating.
Tolerancing

• It is not possible in practice to manufacture products to the exact figures

displayed on an engineering drawing. The accuracy depends largely on the
manufacturing process. A tolerance value shows the manufacturing
department the maximum permissible variation from the dimension.
• Each dimension on a drawing must include a tolerance value. This can
appear either as:

• a general tolerance value applicable to several dimensions. i.e. a note

specifying that the General Tolerance +/- 0.5 mm.

• or a tolerance specific to that dimension

Drawing layout
All engineering drawings should feature a title block.

The title block should include:

Title:- title of the drawing

Name:- name of the person who produced the drawing
Checked:- before manufacture, drawings are usually checked
Version:- many drawings are amended, each revision must be noted
Date:- the date the drawing was produced or last amended
Notes:- any note relevant to the drawing
Scale:- the scale of the drawing
Company name:- name of the company
Projection:- the projection system used to create the drawing