Scribd
Upload
899 views2 pages

Level Pool Routing Procedure

This document describes the level pool method for reservoir routing. It involves developing a storage-outflow function relating storage (S), outflow (Q), and time step (Δt). An inflow hydrograph is then routed through the reservoir using the continuity equation. Key steps include: 1) determining the Q-H and S-H relationships, 2) calculating storage at each time step using the continuity equation, 3) interpolating outflow from the storage-outflow function, and 4) advancing to the next time step. The method relies on linear interpolation to estimate outflow between known storage values.

Uploaded by

palaisdemari631
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
899 views2 pages

Level Pool Routing Procedure

This document describes the level pool method for reservoir routing. It involves developing a storage-outflow function relating storage (S), outflow (Q), and time step (Δt). An inflow hydrograph is then routed through the reservoir using the continuity equation. Key steps include: 1) determining the Q-H and S-H relationships, 2) calculating storage at each time step using the continuity equation, 3) interpolating outflow from the storage-outflow function, and 4) advancing to the next time step. The method relies on linear interpolation to estimate outflow between known storage values.

Uploaded by

palaisdemari631
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Reservoir Routing with the Level Pool Method

Solution Procedure
Level pool routing consists of two main components:
1. Develop the storage-outflow function, Q vs. 2S/Δt + Q
2. Route the inflow hydrograph through the reservoir using the discrete form of the continuity
equation

 2S j 1   2S j 
  Q j 1   I j  I j 1     Q j 
 t   t 

Steps to develop storage-outflow function


1. Determine the Q-H relation. This relation will be given based on measured outflow or
calculated using the features of the outflow structure(s), e.g. orifice and/or weir equations.
2. Determine the S-H relation using the reservoir geometry.
3. Find 2S/Δt + Q using the results of the first two steps (note: Δt is determined by the inflow
hydrograph).

Comments:
 Watch units for Δt! Q is usually in cfs; therefore S must be in ft3 and Δt in s.
 If Q increases faster than 2S/Δt, the solution will become unstable. In this situation, reduce
Δt.

Steps to route hydrograph (computations occur at the j+1 step)


1. Calculate I j  I j 1

 2S j 
2. If j+1 = 2, calculate   Q j  , i.e. for the previous step (if the basin is empty and there
 t 
is no outflow, the value will be zero). After j+1 = 2, this step is not necessary.
 2S j 1   2S j 
3. Calculate   Q j 1   I j  I j 1     Q j 
 t   t 

CE 460/560 Level Pool Routing 1


4. Linearly interpolate the value for Qj+1 using the value from the previous step and storage-
outflow function. Once Qj+1 is found, the depth in the reservoir H can be found by
interpolating the Q-H relation or direct calculation, if an equation is available.
 2S j 1   2S j 1 
5. Calculate   Q j 1     Q j 1   2Q j 1 . This value is needed for the next time
 t   t 
step, (j+2), and replaces step 2.

Review of Linear Interpolation


Given pairs of known values (x1, y1) and (x2, y2), the interpolated value for y corresponding to a
given value of x where x1 ≤ x ≤ x2 is

 y 2  y1  
y  y1  x  x1 
x2  x1 

y2

y1

x1 x2

CE 460/560 Level Pool Routing 2

You might also like