2019 SDC Official Rules

Sixteenth Annual Undergraduate
Seismic Design Competition (SDC)
OFFICIAL RULES
Organized and Run by:

EERI Student Leadership Council (SLC)
Competition Website: https://slc.eeri.org/2019-seismic-design-competition/

Table of Contents
1. Introduction ......................................................................................................................... 4
1.1 Competition Objectives ...................................................................................................................................4
1.2 Problem Statement ..........................................................................................................................................4
1.3 Eligibility and Registration ............................................................................................................................. 6
1.4 Units ................................................................................................................................................................ 7
1.5 Summary of Notable Rule Changes for this Year ...........................................................................................7
2. Scoring .................................................................................................................................. 8
2.1 Design Proposal, Presentation, Poster, and Architecture.................................................................................8
2.2 Performance Predictions and Floor Area Calculations .................................................................................. 10
2.3 Annual Revenue ............................................................................................................................................ 12
2.4 Annual Building Cost .................................................................................................................................... 12
2.5 Annual Seismic Cost ..................................................................................................................................... 13
2.6 Final Annual Building Income ...................................................................................................................... 14
3. Competition Awards .......................................................................................................... 15
3.1 Competition Winner and Ranking ................................................................................................................. 15
3.2 Honorable Mentions ...................................................................................................................................... 15
3.3 Best Communication Skills Award ............................................................................................................... 15
3.4 Charles Richter Award for the Spirit of the Competition .............................................................................. 16
3.5 Egor Popov Award for Structural Innovation ................................................................................................ 16
4. Design Proposals and Damping Device Approval Process ............................................. 16
4.1 Design Proposals ........................................................................................................................................... 16
4.2 Damping Device Approval Process............................................................................................................... 18
5. Structural Model ................................................................................................................ 19
5.1 Structural Model Materials ............................................................................................................................ 19
5.2 Frame Members............................................................................................................................................. 19
5.3 Wall Members ............................................................................................................................................... 20
5.4 Connections ................................................................................................................................................... 20
5.5 Floor Dead Load Connections ....................................................................................................................... 22
5.6 Floors............................................................................................................................................................. 23
5.7 Structural Model Base Plate .......................................................................................................................... 26
5.8 Structural Model Roof Plate .......................................................................................................................... 28
5.9 Innovative Damping Devices ........................................................................................................................ 29
5.10 Building Finish .............................................................................................................................................. 30
5.11 Building Display Requirements .................................................................................................................... 30
5.12 Structural Model Weight ............................................................................................................................... 30
6. Strong Ground Motion Testing ........................................................................................ 30
6.1 Scaled Ground Motions ................................................................................................................................. 30
6.2 Shake Table ................................................................................................................................................... 31
6.3 Dead Load Specifications .............................................................................................................................. 31
6.4 Dead Load Installation .................................................................................................................................. 31
6.5 Attachment of Structural Model to the Shake Table ..................................................................................... 32
6.6 Instrumentation.............................................................................................................................................. 33
6.7 Data Processing ............................................................................................................................................. 33
6.8 Damage Calculations ..................................................................................................................................... 34
6.9 Penalties and Determining Collapse .............................................................................................................. 35
7. Score Sheets ........................................................................................................................ 36
7.1 Verification of Electronic Score Sheet Entry ................................................................................................ 37
2019 Undergraduate Seismic Design Competition- Rules 2

8. Rule Clarifications ............................................................................................................. 38
9. Judging and Appeals.......................................................................................................... 38
9.1 Appeals Process............................................................................................................................................. 38
9.2 Rule Modifications ........................................................................................................................................ 39
10. Code of Conduct and Plagiarism ...................................................................................... 39

1. Introduction
1.1 Competition Objectives
The objectives of the 16th Annual Undergraduate Seismic Design Competition
sponsored by EERI are:
• To promote the study of earthquake engineering among undergraduate
students.
• To build professional relationships between EERI student members and EERI
professional members.
• To provide civil engineering undergraduate students with an opportunity to
work on a hands-on project designing and constructing a cost-effective frame
building to resist seismic loading.
• To promote EERI activities among undergraduate students as well as the
general public, and to encourage international participation in these activities.
1.2 Problem Statement
Vancouver, British Columbia, located on the western coast of Canada, is known for
its urban livability and stunning natural backdrop. Vancouver, full of famous parks
and delicious seafood, is located near the edge of the Cascadia subduction zone,
where the Juan de Fuca, Pacific, and North American plates meet. Due to the Juan de
Fuca plate moving under the less dense North American plate, a prospective
megathrust earthquake is expected to develop approximately 300 kilometers off the
coast of Vancouver. In addition to this, deformation of the North America plate has
created many small shallow faults that could rupture as few as 10 kilometers beneath
the city. While not a megathrust earthquake, these smaller crustal ruptures could
cause more damage for the city due to their proximity.
Your company has been tasked with responding to a Request for Proposal (RFP) to
construct a new building in downtown Vancouver. The client has high expectations
that this new building will be an iconic structure and a celebrated addition to the
downtown area. Vancouver is the most densely populated city in Canada and as such
the client has purchased a smaller piece of land than anticipated. Additionally, Metro
Vancouver’s Regional Growth Strategy (RGS) encourages mixed-use development.
The client plans to leave two corners of the land for a small park and bike garage
leaving a T-shaped area for the building footprint. Consistent with conventional urban
use of multi-story buildings, the client would like to lease the lowermost level of the
structure as retail space. To maximize the value of this space, the height of the first
floor will be double of the typical floor height. The client also plans to lease the top
floor as retail space, capitalizing on the scenic views that downtown Vancouver
offers. The client has given you, the engineer and designer, the ability to decide how
the remaining stories in the building will be rented (residential, office, etc.). With its
Greenest City Initiative approved in July 2011, Vancouver is aiming to become the
greenest city in the world by 2020 and your building should feature efficient and
creative approaches to minimize the building’s carbon footprint.

Vancouver is primarily situated on Ice Age sediments creating layers of sandstone
and shale. As mentioned previously, your building will be in the heart of downtown
Vancouver, and existing tunnels, city utility lines, and neighboring buildings might
affect the seismic response of a new high-rise structure. Although the structural
model does not need to account for the subsurface conditions, your proposal must
demonstrate an understanding of the geotechnical challenges posed by these
considerations.
To verify the seismic load-resisting system, a scaled balsa wood model of the
proposed building design will be constructed and tested. The model will be subjected
to two ground motions, representing earthquakes with different return periods. To
ensure life safety, the building model must not collapse during either of the ground
motions. The response of the model, quantified through roof drift and roof
acceleration, will be measured during the shaking. For each ground motion, the value
of the roof drift will be used to estimate the monetary losses due to damage in the
structural and non-structural building components. Likewise, the roof acceleration
will be used to estimate the monetary loss due to damaged equipment contained
inside the building. If collapse occurs, the monetary losses will account for
demolition, reconstruction, and downtime. Finally, the annual seismic cost will be
determined as the sum of the economic loss estimated for each of the earthquakes
divided by its return period.
A cost-benefit analysis will be carried out to determine the most cost-effective

building. This will be done by balancing the revenue with the initial building cost and
seismic cost.
• The Annual Revenue (Section 2.3) will be a function of the rentable floor area.
Bonuses in revenue will be given to those teams with the best design proposal,
architecture, presentation, and poster. These bonuses account for the positive
effect that quality architecture and effective communication skills can have on
increasing the value of the floor area to be sold or rented.
• The Annual Building Cost (Section 2.4) will be a function of the weight of the
building model. Penalties that increase the initial cost will be applied to those
models that do not meet all structural model requirements.
• The Annual Seismic Cost (Section 2.5) will be based on the building’s seismic
performance. A bonus will be given to the teams with the best performance
predictions. This bonus will reduce the seismic cost of the building. This accounts
for the fact that a detailed structural analysis can improve structural design and
lead to desired seismic performance.
The winner of the competition will be the team with the highest Final Annual
Building Income (Section 2.6) whose building is not deemed collapsed after both
ground motions. Teams whose buildings are deemed collapsed will be ranked in a
lower category than teams whose buildings are not deemed collapsed.

1.3 Eligibility and Registration
All deadlines, instructions, and forms will be posted on the competition website
(listed on the cover page). Any team failing to meet all eligibility requirements or
complete the registration requirements by the deadlines shall not be eligible to
compete in the competition.
The number of teams invited to participate in the competition will be determined by

the Student Leadership Council (SLC). The Design Proposal (Section 4) will be used
to evaluate which teams will be invited to the competition. Invitations will be
announced by email to the team captain and advisor by the date listed on the
competition website. Historically, most teams have earned an invitation to participate
in the SDC by submitting a competitive Design Proposal, and meeting eligibility
requirements. However, a growing interest in the SDC has led to an increasing
number of applicants. The SLC continues to encourage all eligible teams to submit
Design Proposals, but retains the ability to restrict the number of invited teams based
on time limitations and space availability at the conference venue. Therefore, the SLC
recommends paying particular attention to the Design Proposal.
Team registration and eligibility questions should be directed to:
[email protected]
1.3.a Team Eligibility Requirements

The following eligibility requirements will be strictly enforced:
▪ Teams must be affiliated with a registered EERI student chapter in

good standing. To start a student chapter, please reference the
following website:
http://www.eeri.org/about-eeri/student-chapters/how-to-start-an-
eeri-student-chapter/
Exceptions for first year teams creating a new EERI Chapter will be
made on a case by case basis by the SLC Co-Presidents and EERI
Staff.
▪ Teams shall be comprised of undergraduate students only. A team
shall have at least two registered participants and may have as many
undergraduate student participants as they wish. Graduate students are
welcomed to assist undergraduate student participants in the
competition; however, graduate students cannot register as team
members.
▪ Each undergraduate student registered for a team must be a student
member of the national EERI organization and a member of the EERI
student chapter for the school being represented. Exceptions to this
will be made on a case by case basis by the SLC Co-Presidents.
Decisions by the Co-Presidents are final and may not be appealed.
▪ Each competing university shall enter only one undergraduate student
team and one structure at the competition.

▪ Each team must complete all registration requirements.
▪ Any team member who has earned their undergraduate degree
between the submittal of the design proposal and the start of
competition shall be permitted to participate in the competition,
provided that their name appears on the design proposal. Team
members meeting eligibility requirements can be added to the team
roster after the design proposal has been submitted.
▪ Each team shall identify a team captain who will act as the team
liaison for correspondence with the Seismic Design Competition
Chairs (SDC Chairs, hereafter).
1.3.b Team Registration Requirements

All participating teams are required to complete the following registration
requirements:
▪ Proposal Submittal (Section 5)

▪ Final Registration (Invitation Only)
▪ Floor Area Calculations and Performance Predictions (Section 2.2)
1.3.c Important Deadlines and Deliverables
The following are the deadlines for the deliverables listed in Section 1.3.b.
Cutoff will be at 11:59 PM Pacific Time.
Submittal Deadline
Interest Survey Friday, November 2nd, 2018
Proposal Submittal Friday, November 2nd, 2018
Final Registration Tuesday, January, 15th, 2019
Floor Area Calculations &
Friday, March 1st, 2019
Performance Predictions
Teams will be invited to participate by November 19th, 2018.
1.4 Units
All measured and specified parameters in the competition will be in English units,
inches and pounds.
1.5 Summary of Notable Rule Changes for this Year
▪ Predictions are required for both shaking directions.

▪ Minimum member sizes are implemented.
▪ Maximum floor dimensions have been changed.
▪ Floor access requirements have been changed.
▪ Maximum floor area has changed.
▪ Proposal requirements have changed.
▪ Poster size has changed.
▪ Revenue per floor has changed.

2. Scoring
To test the seismic performance of the design, a scaled balsa wood model that is representative
of a real building design must be constructed and tested. The model will be subjected to two
ground motions, which represent earthquakes with different return periods. To ensure life
safety, the client requires a design that does not collapse for either of the two ground motions.
In addition, the response of the model in terms of roof drift and roof acceleration will be
measured for the first ground motion and the value of the peak relative roof drift will be used
to estimate the monetary loss from damage to the structure. The response of the model in terms
of roof drift and roof acceleration is expected for shaking in both the North-South and East-
West directions. The roof acceleration will be used to estimate the monetary loss due to
damaged equipment contained inside the building. If a building is deemed collapsed (as
defined in Section 6.9), the monetary losses will account for demolition, reconstruction, and
downtime. Finally, the annual seismic cost will be the sum of the economic loss estimated for
each of the earthquakes divided by their respective return periods.
This section describes the method used to score the performance of the buildings in the seismic
competition. Scoring is based on three primary components: 1. Annual Revenue, 2. Annual
Building Cost, and 3. Annual Seismic Cost. The final measure of structural performance is the
Final Annual Building Income, which is calculated as the Annual Revenue minus the Annual
Building Cost minus the Annual Seismic Cost.
In the event of a tie for an award in any category, the architecture score will be used as the
tiebreaker.
2.1 Design Proposal, Presentation, Poster, and Architecture

The design proposal portion is detailed in Section 5.1. Bonuses in revenue will be
given to teams that rank highest in the design proposal, presentation, poster, or
architecture scores. These bonuses account for the positive effect of having effective
communication skills or architectural appeal that could increase the value of the floor
to be sold or rented.
Failure to complete any of the requirements in Sections 2.1.a and 2.1.b will result in
an increase in the factor V (Section 2.4). Specific penalties are quantified in each
section.
2.1.a Presentation
Each team is required to give an oral presentation no longer than seven
minutes to a panel of judges at the scheduled time for the team. Judges
will have up to five minutes to ask questions following the presentation.
The presentations will be open to the public.
A projector and laptop, running Microsoft Windows 7 or newer, and

PowerPoint (Office 2007 or newer) will be provided. The presentation
files will be uploaded to the competition laptop by the SLC prior to the
first presentation. Teams must submit their presentation files by email

before the week of the competition (check the official website for exact
deadline). Teams are responsible for software compatibility. Teams may
check software compatibility during the scheduled time for Check-in and
Registration
Presentations shall include the following:
• Name of school on title slide

• Name of building on title slide
• Description of structural system concept
• Architectural concept
• Performance predictions and analysis method
• Damping devices (optional)
• Structural design innovation (optional)
For more information, please see the presentation judging rubric on the
competition website. Any team that does not present at the scheduled time
will have 100 added to V (Section 2.4).
Any team that does not email their final presentation by the deadline will
have 10 added to V (Section 2.4).
2.1.b Poster
Teams are required to display a poster providing an overview of the
project. Teams must submit their poster by email before the week of the
competition (check the official website for exact deadline). Individual
teams are responsible for providing the physical poster for display.
Any team that does not email their poster by the deadline will have 10
added to V (Section 2.4).
The dimensions of the poster are restricted to a height of 30 in. and a width
of 20 in. The minimum font size for all text shall not be less than 18.
The poster shall include the following:
• Name of school (font size 40 recommended)

• Name of building
• EERI logo (available on the competition website)
• SLC logo (available on the competition website)
• 3D rendering of the building (either of structure “skeleton” or
finished building with cladding)
• Typical floor plan
• Performance predictions and analysis method
• Description of balsa-wood fabrication (photos recommended)

• Estimated overall score prediction for both shaking directions
(Final Annual Building Income, FABI)
Any team that does not have a poster in the display area meeting all
requirements in this section by the time listed in the schedule will receive
50 added to V (Section 2.4).
2.1.c Architecture
The architecture will be judged based on the aesthetic appeal of the
structural model. Renderings on the poster will be considered in the
architecture score. Refer to the competition website for the score rubric
that will be used.
Because not all teams have access to laser cutting, quality of member
fabrication will not be considered in the architectural judging.
2.1.d Bonus Scoring

The increase in Annual Revenue will be determined by the team’s rank in
the design proposal, oral presentation, poster, and architecture. Only the
top 9 teams in the design proposal, presentation and poster category will
receive this benefit. Only the top 5 teams in the architecture category will
receive this benefit. See Table 2-1 for the percentage increase per rank.
Table 2-1: Annual Revenue Bonus
Rank Proposal Presentation Poster Architecture

1st 15% 15% 12% 8%
2nd 12% 12% 10% 6%
3rd 10% 10% 8% 4%
4th 8% 8% 6% 2%
5th 6% 6% 5% 1%
6th 4% 4% 4% 0%
7th 3% 3% 3% 0%
8th 2% 2% 2% 0%
9th 1% 1% 1% 0%
≥10th 0% 0% 0% 0%
2.2 Performance Predictions and Floor Area Calculations

A bonus will be given to the teams with the best performance predictions. This bonus
will reduce the seismic cost of the building. This accounts for the fact that a detailed
structural analysis can improve structural design leading to better seismic
performance.

Teams are required to predict the absolute value of the peak roof drift and the peak
roof absolute acceleration for both ground motions with shaking in both the North-
South and the East-West Directions (a total of 4 predictions). Although performance
predictions for both ground motions are required, only the performance predictions
for Ground Motion 1 will affect the annual income.
The performance predictions must be submitted by the deadline listed on the

competition website. Instructions for submitting performance predictions will be
posted on the competition website. If performance predictions are not submitted by
the deadline, the SDC chairs will assume zero for all predictions.
2.2.a Performance Predictions Requirements

The Annual Seismic Cost will be reduced based on the team’s rank in the
performance predictions for Ground Motion 1. Each team is required to
report the peak relative roof displacement in inches and the peak absolute
roof acceleration in g’ s for each ground motion, n:
𝐷𝑖𝑠𝑝𝑛 𝑃𝑟𝑒𝑑𝑖𝑐𝑡𝑒𝑑 = max|Δ𝑅𝑜𝑜𝑓 𝑛 𝑃𝑟𝑒𝑑𝑖𝑐𝑡𝑒𝑑 [𝑖𝑛] − Δ𝐵𝑎𝑠𝑒 𝑛 𝑃𝑟𝑒𝑑𝑖𝑐𝑡𝑒𝑑 [𝑖𝑛]|

𝐴𝑐𝑐𝑙𝑛 𝑃𝑟𝑒𝑑𝑖𝑐𝑡𝑒𝑑 = max|𝐴𝑐𝑐𝑙𝑛 𝑃𝑟𝑒𝑑𝑖𝑐𝑡𝑒𝑑 [𝑔]|
The Analysis Prediction Score (APS) is used to evaluate the accuracy of the
predicted performance (taken to two significant figures). APS1 is for the
maximum absolute roof drift prediction while APS2 is for the peak roof
absolute acceleration. See Section 2.5 for how XPeak1 and APeak1 are
determined
𝐷𝑖𝑠𝑝
|𝑆𝑡𝑟𝑢𝑐𝑡𝑢𝑟𝑎𝑙1 𝑃𝑟𝑒𝑑𝑖𝑐𝑡𝑒𝑑 − 𝑋𝑃𝑒𝑎𝑘1 |
𝑀𝑜𝑑𝑒𝑙 𝐻𝑒𝑖𝑔ℎ𝑡
𝐴𝑃𝑆1 =
𝑋𝑃𝑒𝑎𝑘1
|𝐴𝑐𝑐𝑙1 𝑃𝑟𝑒𝑑𝑖𝑐𝑡𝑒𝑑 − 𝐴𝑃𝑒𝑎𝑘1 |

𝐴𝑃𝑆2 =
𝐴𝑃𝑒𝑎𝑘1
𝐴𝑃𝑆 = 𝐴𝑃𝑆1 + 𝐴𝑃𝑆2
Each team will be ranked based on the accuracy of the predictions for
Ground Motion 1. Any team that does not submit a prediction by the
deadline will receive an APS equal to 100%. Any team with an APS value
greater than 100% will receive an APS value of 100%. The top ten teams
with the lowest APS, and with an APS values under 100%, are awarded an
Analysis Prediction Score Bonus (APS Bonus). If less than 10 teams have
APS values under 100%, then the APS Bonus will only be applied to those
teams (i.e. some bonus percentages may not be given). See Table 2-2 for
the percentage increase per rank.

Table 2-2: Analysis Prediction Score Bonus
Rank APS Bonus

1st 12%
2nd 10%
3rd 8%
4th 7%
5th 6%
6th 5%
7th 4%
8th 3%
9th 2%
10th 1%
11th ≥ 0%
2.2.b Floor Area Calculations

Along with performance predictions, teams are required to submit their
rentable floor areas (Section 5.6). Submitted floor areas will be verified by
the SDC Chairs. Any team that does not submit their rentable floor areas by
the deadline will receive the minimum value (Section 5.6.b) for those floors.
2.3 Annual Revenue

The Annual Revenue will be based on the total rentable floor area (Section 5.6.b and
5.6.c):
$250 per year per square inch for floors 1 through 2

$275 per year per square inch for floors 16 and above
The Annual Revenue is equal to the sum of each rentable floor area multiplied by its
respective revenue per square inch factor.
2.4 Annual Building Cost

The Annual Building Cost will be obtained as a function of the Construction Cost,
Additional Construction Cost, Damping Device(s) cost, Land Cost, and Design Life.
$
𝐶𝑜𝑛𝑠𝑡𝑟𝑢𝑐𝑡𝑖𝑜𝑛 𝐶𝑜𝑠𝑡 = 𝐶𝑐 = 2,500,000 [ ] × (𝑊𝑠 [𝑙𝑏])2 + 6 × 106 [$]
𝑙𝑏 2
𝐴𝑑𝑑𝑖𝑡𝑖𝑜𝑛𝑎𝑙 𝐶𝑜𝑛𝑠𝑡𝑟𝑢𝑐𝑡𝑖𝑜𝑛 𝐶𝑜𝑠𝑡 = 𝐶𝑎 = 200,000 [$] × 𝑉
𝐷𝑎𝑚𝑝𝑖𝑛𝑔 𝐷𝑒𝑣𝑖𝑐𝑒(𝑠) 𝐶𝑜𝑠𝑡 = 𝐶𝑑 = (0.00625 × 𝑁𝑑 + 0.0125) × 𝐶𝑐 if 𝑁𝑑 ≤ 10.

Otherwise 𝐶𝑑 = 0.075 × 𝐶𝑐

$
𝐿𝑎𝑛𝑑 𝐶𝑜𝑠𝑡 = 35,000 [ 2 ] × 𝐴𝑓 [𝑖𝑛2 ]
𝑖𝑛
𝐷𝑒𝑠𝑖𝑔𝑛 𝐿𝑖𝑓𝑒 = 100 [𝑦𝑒𝑎𝑟𝑠]
𝐶𝑐 [$] + 𝐶𝑎 [$] + 𝐶𝑑 [$] + 𝐿𝑎𝑛𝑑 𝐶𝑜𝑠𝑡[$]

𝐴𝑛𝑛𝑢𝑎𝑙 𝐵𝑢𝑖𝑙𝑑𝑖𝑛𝑔 𝐶𝑜𝑠𝑡 =
𝐷𝑒𝑠𝑖𝑔𝑛 𝐿𝑖𝑓𝑒 [𝑦𝑒𝑎𝑟𝑠]
Any violations will result in an increase in V and will contribute to the Additional
Construction Cost, Ca. The structural model weight, Ws, is defined in Section 5.12.
The building footprint, Af, is defined as the maximum floor plan area projected onto
the base plate with units squared inches. The number of approved damping device(s)
is Nd.
2.5 Annual Seismic Cost

The Annual Seismic Cost will be based on the building’s seismic performance, the
Equipment Cost, Return Periodn, XDn (Section 6.8.a), ADn (Section 6.8.b), and
Construction Cost (Section 2.4).
𝐸𝑞𝑢𝑖𝑝𝑚𝑒𝑛𝑡 𝐶𝑜𝑠𝑡 = 20,000,000 [$]
𝑅𝑒𝑡𝑢𝑟𝑛 𝑃𝑒𝑟𝑖𝑜𝑑1 = 50 [𝑦𝑒𝑎𝑟𝑠]

𝑅𝑒𝑡𝑢𝑟𝑛 𝑃𝑒𝑟𝑖𝑜𝑑2 = 300 [𝑦𝑒𝑎𝑟𝑠]
The structural damage as a percentage of the construction cost, XDn [%], and
equipment damage as a percentage of the equipment cost, ADn [%], for a given
ground motion n, are calculated using a cumulative distribution function (Section 6.8)
and are defined as follows:
𝑋𝐷𝑛 = 𝐶𝐷𝐹(𝜇𝑋 [%], 𝜎𝑋 [%], 𝑋𝑃𝑒𝑎𝑘𝑛 [%])

𝐴𝐷𝑛 = 𝐶𝐷𝐹(𝜇𝐴 [𝑔], 𝜎𝐴 [𝑔], 𝐴𝑃𝑒𝑎𝑘𝑛 [𝑔])
The mean and standard deviation peak roof drift and mean and standard deviation
peak roof acceleration are defined as follows:
𝜇𝑋 = 1.5 [%]
𝜎𝑋 = 0.5 [%]
𝜇𝐴 = 1.75 [𝑔]
𝜎𝐴 = 0.7 [𝑔]
The measured peak roof drift, XPeakn [%], and measured peak roof acceleration,
APeakn [g] for a given ground motion n, are calculated using the absolute roof

displacement, absolute base displacement, absolute roof acceleration (Section 6.7),
and Structural Model Height (Section 5.6.a) and are defined as follows:
max|Δ𝑅𝑜𝑜𝑓 𝑛 [𝑖𝑛] − Δ𝐵𝑎𝑠𝑒 𝑛 [𝑖𝑛]|

𝑋𝑃𝑒𝑎𝑘𝑛 =
𝑆𝑡𝑟𝑢𝑐𝑡𝑢𝑟𝑎𝑙 𝑀𝑜𝑑𝑒𝑙 𝐻𝑒𝑖𝑔ℎ𝑡 [𝑖𝑛]
𝐴𝑃𝑒𝑎𝑘𝑛 = max|𝐴𝑐𝑐𝑙𝑛 [𝑔]|
If the structural model is not deemed collapsed (Section 6.9.c) after ground motion n
and all previous ground motions, the Economic Loss for the given ground motion, n,
will be equal to:
𝐸𝑐𝑜𝑛𝑜𝑚𝑖𝑐 𝐿𝑜𝑠𝑠𝑛 = 𝑋𝐷𝑛 [%] × 𝐶𝑜𝑛𝑠𝑡𝑟𝑢𝑐𝑡𝑖𝑜𝑛 𝐶𝑜𝑠𝑡[$]

+𝐴𝐷𝑛 [%] × 𝐸𝑞𝑢𝑖𝑝𝑚𝑒𝑛𝑡 𝐶𝑜𝑠𝑡[$]
Teams will have the option of leaving the accelerometer in place during Ground
Motion 2. The data from the accelerometer will not be used for judging, therefore, if
the structural model does not collapse after Ground Motion 2, both XDn and ADn will
be equal to 50%.
If the structural model is deemed collapsed (Section 6.9.c) after ground motion n, the
Economic Loss for the given ground motion, n, and subsequent ground motions will
be equal to:
𝐸𝑐𝑜𝑛𝑜𝑚𝑖𝑐 𝐿𝑜𝑠𝑠𝑛 = 𝐸𝑞𝑢𝑖𝑝𝑚𝑒𝑛𝑡 𝐶𝑜𝑠𝑡 [$] + 2 × 𝐶𝑜𝑛𝑠𝑡𝑟𝑢𝑐𝑡𝑖𝑜𝑛 𝐶𝑜𝑠𝑡 [$]

+3 × 𝐴𝑛𝑛𝑢𝑎𝑙 𝑅𝑒𝑣𝑒𝑛𝑢𝑒 [$]
The Annual Economic Loss, AEL, for a given ground motion, n, is equal to:
𝐸𝑐𝑜𝑛𝑜𝑚𝑖𝑐 𝐿𝑜𝑠𝑠𝑛
𝐴𝐸𝐿𝑛 =
𝑅𝑒𝑡𝑢𝑟𝑛 𝑃𝑒𝑟𝑖𝑜𝑑𝑛
A penalty, Dn, for unsecured floor dead loads will be applied after each ground
motion (Section 6.9.a).
The Annual Seismic Cost is equal to:
𝐴𝑛𝑛𝑢𝑎𝑙 𝑆𝑒𝑖𝑠𝑚𝑖𝑐 𝐶𝑜𝑠𝑡 = 𝐴𝐸𝐿1 (1 + 𝐷1 ) + 𝐴𝐸𝐿2 (1 + 𝐷2 )
2.6 Final Annual Building Income

The team with the largest Final Annual Building Income (FABI) will be the winning
team. FABI is equal to the Final Annual Revenue (FAR) minus the Final Annual
Building Cost (FABC) and Final Annual Seismic Cost (FASC).

Final Annual Revenue (FAR) is equal to:
FAR = (1 + Prop. Bonus + Pres. Bonus + Poster Bonus + Arch. Bonus) ×

Annual Revenue
Final Annual Building Cost (FABC) is equal to:
FABC = Annual Building Cost
Final Annual Seismic Cost (FASC) is equal to:
FASC = (1 – APS Bonus) × Annual Seismic Cost
The Final Annual Building Income (FABI) is equal to:
FABI = FAR – FABC – FASC
3. Competition Awards
3.1 Competition Winner and Ranking

The team that designs the building with the highest Final Annual Building Income
(FABI) that is not deemed collapsed in any of the two ground motions will be the
winner of the competition.
Teams whose buildings collapse will be ranked in a lower category than teams whose
buildings do not collapse. Within each category, teams will be ranked based on the
Final Annual Building Income, FABI.
The teams ranked overall 2nd and 3rd will also be awarded.
3.2 Honorable Mentions

Two honorable mentions will be awarded to a team that exemplifies strong
performances in individual aspects of the competition:
▪ An Honorable Mention for Best Architecture will be awarded to the team ranked
1st in architecture.
▪ An Honorable Mention for Best Seismic Performance will be awarded to the team
with the lowest Final Annual Seismic Cost, FASC.
3.3 Best Communication Skills Award

An award will be given to the team whom best exemplifies professional
communications throughout all facets of the competition. The communications score
will be primarily considered for this award, but the SLC reserves the right to consider
other variables as needed to determine the winner.

Communications score = 1.5(Presentation Score) + Poster score + Proposal Score
The SLC reserves the right to assess a penalty of a 5% reduction in the communication score to
any team which demonstrates unprofessional written or oral communication to the SLC members
at any time leading up to or during the competition.
3.4 Charles Richter Award for the Spirit of the Competition

The most well-known earthquake magnitude scale is the Richter scale which was
developed in 1935 by Charles Richter of the California Institute of Technology. In
honor of his contribution to earthquake engineering, the team which best exemplifies
the spirit of the competition will be awarded the Charles Richter Award for the Spirit
of Competition. The winner for this award will be determined by the participating
teams.
3.5 Egor Popov Award for Structural Innovation

Egor Popov was a Professor at the University of California, Berkeley for almost 55
years before he passed away in 2001. Popov was born in Russia, and escaped to
Manchuria in 1917 during the Russian Revolution. After spending his youth in China,
he immigrated to the U.S. and studied at UC Berkeley, Cal Tech, MIT and Stanford.
Popov conducted research that led to many advances in seismic design of steel frame
connections and systems, including eccentric bracing. In honor of his contribution to
structural and earthquake engineering, the team which makes the best use of
technology and/or structural design to resist seismic loading will be awarded the Egor
Popov Award for Structural Innovation. The winner for this award will be determined
by the SLC members.
4. Design Proposals and Damping Device Approval Process
4.1 Design Proposals

Your team is required to submit a proposal for evaluation by the SDC Chairs.
Invitation to participate in the competition will be determined by the proposal score.
If a team fails to submit their proposal by the deadline, they will not be invited to
participate in the competition. The number of accepted teams will be based on time
limitations and space availability at the conference venue. No funding will be offered
to teams for their proposals—instead, funds will be used to improve the quality of the
venue and activities that benefit all attendees. A bonus score multiplier will be
awarded to the ten best proposals (Section 2.1.d). The following is an itemized list of
the deliverables required in the proposal:
• The proposal shall not exceed 3 pages. Any proposal exceeding the page limit
will not be scored.
• Plagiarism is strictly prohibited and may result in disqualification or non-
invitation to compete. Any citation style is accepted, as long as it is consistent.

Works Cited or References pages are required but do not count toward the page
limit. See Section 10 for more information.
• Format requirements: 11pt, single-spaced, US Letter (8.5 in x 11 in), Times
New Roman font with 1 inch margins.
• Page 1: Title Page
o Name of the school, overall computer-generated image of the exposed
structural system (an optional computer-generated image of the final
architectural state may also be included), names of all team members
and the designated team captain.
(Note: the designated team captain will be the only point of contact
between the team and the SDC Chairs from the start of the design to
the completion of the competition).
• Pages 2 - 3: Proposal Content
o Proposals will be judged on the following:
▪ A summary of the site conditions and seismic activity expected
for the Vancouver, B.C. region (e.g., soil type, historic
earthquakes, major faults, magnitude and shaking expected for
future earthquakes, and any other information relevant for
seismic design considerations)
▪ Description of the structural system and elaboration on the
plans for predicting the structural behavior (computer
modeling, small-scale testing, etc.)
▪ Explanation of how the client’s architectural requirements (as
detailed in the problem statement) will be met and any other
economic considerations.
▪ Professionalism demonstrated through concise and clear
writing with a good command of grammar and spelling.
o Proposed damping devices may be included in the proposal, but are
not necessary. Final approval of the damping devices must be made
through the Damping Device Approval Process (Section 4.2).
o Diagrams and photos are recommended but must fit within the page
limit.
o For additional information, please see the Design Proposal Rubric on
the competition website.
• Page(s) 4(+): Works Cited
o Teams must cite the references that they use in creating their proposal.
o No additional content for the proposal may be included on the Works
Cited page(s).
A PDF of the document must be emailed to the SDC Chairs at the following email
address by the date listed on the competition website. The SDC Chairs will confirm
the submission.
[email protected]

Teams are not bound to the designs submitted in the design proposal process. Design
proposals are not evaluated for rule violations. Selected designs are still subject to
penalization or disqualification. Teams are responsible for ensuring that their
buildings follow the competition rules. For any clarification, refer to the clarifications
section on the competition website, or the team captain can submit a clarification
request (See Section 8).
4.2 Damping Device Approval Process

All proposed damping devices shall be subjected to the approval process. A separate
PDF document, no more than 2 pages (including figures), shall be submitted to
[email protected] by the date listed on the competition website. More than one damping
device proposal may be submitted. Each proposed damping device must be described
in detail, explaining the mechanism used to dissipate energy and its placement within
the structural model. Figures are highly recommended to aid in describing the
damping device.
Prior to approval, judges will evaluate the proposed damping device(s) and may ask
for testing results and predicted design forces from a computer model (e.g., subjected
to Ground Motion 2) to prove the damping devices would dissipate energy. If the
judges ask for additional information about the proposed damping device(s), that
information must be provided within fourteen days of the initial request. Failure to
provide the requested information to the judges within the specified time frame will
result in the damping device(s) not being approved. Pre-approved damping devices
are not required to be used in the submitted structural model at the competition.
However, if a damping proposal is not submitted, then damping devices may not be
used.
The criteria used by the judges to approve a damping system are as follows:
• If the damping system is removed, the balsa wood structure, with all dead
load weights attached, should be stable and firmly fixed to the base plate.
• The primary purpose of the pre-approved damping devices is to dissipate
energy.
• Base or floor isolation of any kind is prohibited.
General notes:
• Damping devices may be attached to the base plate.
• All damping devices must dissipate energy at each location used in the
structural model.
• Any material is allowed to manufacture a damping device.
• Nonlinear springs may be used for hysteretic damping but testing data and
expected model forces at the desired use locations will not be required.
If a damping device is approved, the damping device shall not deviate from the
damping device approved through this process in the final structural model. The
damping device may only be located at the approved locations. The damping device
must not interfere with dead load installation locations.

All damping devices will be checked during pre-judging of structures. Damping
devices that have not been approved by the SDC Chairs, or deviate from the approved
submitted damping device proposal (e.g., installation location, connection to
structure, material) will have to be removed. If a team is unable to remove an
unapproved damping device, the structure will be considered collapsed for all ground
motions.
5. Structural Model
This section describes the rules and limitations to be followed for the structural model. Most
violations will result in penalties added to V (Section 2.4). Some violations may result in
disqualification. Penalties will be given in accordance with the official rules and at the
discretion of the judges. The SLC reserves the right to cap violations as needed in accordance
with the spirit of the competition.
Structural models shall be constructed of only balsa wood (Section 5.1) frame members
(Section 5.2) and balsa wood wall members (Section 5.3) that are attached to a structural model
base plate (Section 5.7) with a structural model roof plate attached on top of the structural
model (Section 5.8). Pre-approved damping devices may be made of any material (Section
5.9). All connections requirements are provided in Section 5.4. Floor labels (Section 5.11) and
the school name at the top of the building (Section 5.11) may be constructed out of paper.
Any architectural features (i.e., features not intended for structural purposes) on the model
must be made of balsa wood (Section 5.1) and meet all the requirements for a frame member
(Section 5.2) or wall member (Section 5.3) including all connection requirements (Section 5.4).
5.1 Structural Model Materials

Any violation of this section will result in the structural model not being tested on the
shake table and the team disqualified.
All frame members and wall members shall be made of balsa wood.
5.2 Frame Members

5.2.a Frame Member Dimensions
Each member found to be in violation will be assessed a penalty of 2 V
for every 0.100 in. increment in unit length found to be in violation.
Dimensions between increments will be rounded up. A tolerance of 0.01
in. shall apply.
Each individual frame member in its final state attached to the model shall
fit in a 0.200 in. by 0.200 in. by 15.000 in. box.
Each individual frame member shall have no individual dimension

smaller than 0.09 in.

Individual frame members will not be removed from the model to check
the requirements for this section. Instead, a caliper or other measuring
device will be used to check the requirements for this section. Judges must
be able to visually observe the extent of all members for measuring.
Judges reserve the right to use destructive inspection methods after
completion of shaking to assess penalties in this section.
5.2.b Frame Member Requirements

Each violation of this section will result in 3 added to V.
Any frame member to frame member connections not easily visible to the
naked eye shall be marked with a black arrow pointing to the connection.
5.3 Wall Members

5.3.a Wall Member Dimensions
Each member found to be in violation will be assessed a penalty of 3 V
for every 0.100 in. increment in unit length found to be in violation.
Dimensions between increments will be rounded up. A tolerance of 0.01
in. shall apply.
Each individual wall member in its final state attached to the model shall
fit in a 0.100 in. by 3.000 in. by 11.000 in. box.
A wall member shall span at least 1.50 in. vertically. Measured parallel to
the plane of the base plate, one of the measured dimensions shall measure
at least 1 in.
Individual wall members will not be removed from the model to check the
requirements for this section. Instead, a caliper or other measuring device
will be used to check the requirements for this section. Judges must be
able to visually observe the extent of all members for measuring. Judges
reserve the right to use destructive inspection methods after completion
of shaking and assess penalties in this section.
5.3.b Wall Member Requirements

▪ A wall shall be oriented so that the direction of the grain of wood is
normal to the top surface of the structural model base plate.
5.4 Connections
5.4.a Connection Requirements
Only glue shall be used between the contact surfaces of individual

members. Glue shall only be present at the contact surfaces of individual

members unless deemed excess glue. There are no restrictions on the type
of glue.
It is the discretion of the SDC Chairs to assess V for ungluded connections

if that connection (regardless if the two adjoining members are close, but
are not touching) is reasonably expected to be jointed. For example, floor
beam elements can be reasonabaly expected to be connected to perimeter
beams and are typically not cantilevered within a footprint of perimeter
beams.
All frame members and wall members in contact with the base plate must
be glued to the base plate.
All frame members and wall members in contact with the roof plate must
be glued to the roof plate.
5.4.b Frame Member to Frame Member Connections

Any frame members in contact shall have glue between the faying
surfaces of the frame members. The faying surface is defined as the
surface or portion of a surface of a frame member in direct contact with
the surface or portion of a surface of another frame member.
A faying surface shall not exceed 1 in. in any direction from the centroid
of the faying surface. For each inch that a faying surface exceeds the 1 in.
maximum (e.g. 2 in. faying surface), an additional 3 V will be added. If
frame members are laminated, such as in a column, each surface in contact
with another surface will be considered a faying surface.
Excess glue is any glue more than ½ an inch away in any direction from
a fraying surface (Teams should take care when choosing and applying
glue to connections).
5.4.c Gusset Plates

Gusset plates are permitted but shall not be in contact with any wall
members. A gusset plate shall be in contact with at least two frame
members in contact. Individual gusset plates shall not be in contact with
one another. Each gusset plate shall fit in a 0.100 in. by 1 in. by 1 in. box.
For each member that was designed as a gusset plate that exceeds the
0.100 in by 1 in by 1 in box, a penalty of 3 will be added to V. All gusset
plate surfaces or portion(s) of gusset plate surfaces in contact with frame
members shall be glued. Excess glue shall be confined to 1/2 in. in any

direction of the edge of any faying surface between a frame member and
gusset plate.
Individual gusset plates will not be removed from the model to check the
requirements for this section. Instead, a caliper will be used to check the
requirements for this section.
5.4.d Wall Member to Wall Member Connections

Any wall members in contact shall have glue between the faying surfaces
of the wall members. The faying surface is defined as the surface or
portion of a surface of a wall member in direct contact with the surface or
portion of a surface of another wall member.
Excess glue is any glue more than ½ an inch away in any direction from
a faying surface (Teams should take care when choosing and applying
glue to connections). There is no restriction on length of faying surface in
wall member to wall member connections.
5.4.e Frame Member to Wall Member Connections

Any frame member and wall member in contact shall have glue between
the faying surfaces of the frame member and wall member. The faying
surface is defined as the surface or portion of a surface of a frame member
in direct contact with the surface or portion of a surface of a wall member.
Excess glue is any glue not between the faying surfaces but in contact
with glue between a faying surface and shall be confined to 1/2 in. in any
direction of the edge of any faying surface (Teams should take care when
choosing and applying glue to connections). There is no restriction on
length of faying surface in frame member to wall member connections.
5.5 Floor Dead Load Connections

Floor dead loads will be added to the structural model prior to shake testing (Section
6.3 and 6.4). The floor dead load will require sufficient support for gravity loading
and lateral seismic loading.
5.5.a Floor Dead Load Connection Design Requirements

Floor dead load connections are required in both North-South and East-
West directions and to be centered in plan-view in relation to the center
of the base plate.

The floor dead load connection shall be designed so that the bottom of the
threaded rod is resting on top of the perimeter floor beams at the following
floors: 5, 7, 9, 11, 13, 15 (if F ≥ 15), 17 (if F ≥ 17), and 19 (if F≥19). See
Section 5.6.a for F.
The dead weights should be able to be installed and nuts be tightened to

ensure a snug fit without breaking any of the connections, frame members,
or wall members in the structural model.
5.5.b Floor Dead Load Connection Recommendations

A time limit will be implemented for teams installing floor dead loads
(Section 6.4.a). Ensure the connections are not too intricate that they
require an excessive amount of time to install.
Floor dead loads will be secured to the structure using nuts and washers.
The connection should be strong enough for the team to tighten the nuts
enough to engage adequate friction between the inner-most washer and
the exterior face of the building to ensure the floor dead load is secure (see
Section 6.4.a)
It is strongly recommended that each team purchase a sample weight to

try out and ensure proper attachment. Penalties will be assessed for dead
weights that are not secured to the structural model after each ground
motion testing and may result in judges deeming the building collapsed
(Sections 6.9.b and 6.9.c).
5.6 Floors
5.6.a Floor and Roof Requirements
Each violation of this section will result in 5 added to V. The total number
of floors, F, of the structural model must be equal to or between the
minimum or maximum number of floors. A floor is defined in Section
5.6.b.
Maximum number of floors: 19

Minimum number of floors: 13
A floor, f, as defined in Section 5.6.b, is required to be within ¼ in. at the

following elevations measured from the top of the base plate to the floor,
f (top of the perimeter beams).
The lobby, or f = 1, shall be at an elevation equal to zero inches. For floors

f = 2 to f = F, the elevation shall be equal to:
𝐹𝑙𝑜𝑜𝑟 𝐸𝑙𝑒𝑣𝑎𝑡𝑖𝑜𝑛𝑓 = 6 [𝑖𝑛. ] + (𝑓 − 2)(3 [𝑖𝑛. ])

A roof, at the elevation 𝐹𝑙𝑜𝑜𝑟 𝐸𝑙𝑒𝑣𝑎𝑡𝑖𝑜𝑛𝐹 + 3 𝑖𝑛., is required above the
top-most floor, F, and does not count as a floor. The structural model roof
plate (Section 5.8) shall be affixed to the roof.
For a given elevation, there shall not be more than one independent floor
as defined in Section 5.6.b.
The requirements in this section will be checked with a measuring device

along the side of the structural model. All floor height measurements
will be measured from the top of the base plate.
5.6.b Floor Definition

To be considered a floor, the following requirements must be met:
▪ A continuous set of perimeter beams shall clearly define the floor

where the top of the perimeter beams defines the floor. Walls and
non-horizontal frame members may interrupt the continuous set of
perimeter beams as long as two horizontal members acting as
perimeter beams are at the same elevation and connected to the
interrupting member(s). Interior floor beams shall be flush with
the top of the perimeter beams. The plane defined by the top of
the perimeter beams, the floor, shall be flat and level.
▪ Using a black permanent marker, a dot should be centrally placed

on the top of each perimeter beam so judges know which beams
define the floor area for a given floor.
▪ The lobby floor is defined by straight black permanent marker

lines drawn on the base plate between frame or wall members
attached to the base plate. A beam at the second-floor level shall
be directly vertical and parallel to any straight black line drawn on
the base plate.
▪ A floor shall have at least 36 in2 of rentable floor area (Section

5.6.c).
The continuous set of perimeter beams will be checked visually. Rentable

floor area will be checked with a ruler or other measuring device. The
floor will be checked for levelness by using a level. If the bubble on the
level is completely outside of the level lines, the floor is not considered
level. The structural model will be placed on a level floor or table when
performing this check.

5.6.c Rentable Floor Area
Any floor area that violates the requirements in this section shall not count
towards rentable floor area.
Rentable floor area may only be within the continuous perimeter beams
of the floor (Section 5.6.b).
Measured perpendicular along the plane of the floor from any perimeter
beam, interior beam, or vertical wall member at the floor elevation, no
span to another perimeter beam, interior beam, or vertical wall member
shall be greater than 2.5 in or smaller than 0.5 in.
Each rentable floor area is calculated using the total plan area defined by
the perimeter beams, meeting the Section 5.6.b and this section’s
requirements. Individual structural members penetrating the rentable floor
area (frame members and wall members) are not subtracted from the
rentable floor area.
Maximum rentable total floor area: 1600 in2
The total rentable floor area will be calculated by summing the individual
rentable floor areas from the bottom up. If the maximum rentable total
floor area is reached, the remaining rentable floor areas above will not
count.
The minimum height clearance for rentable floor area is 2.25 in.
Occupants on the rentable floor must be able to access any area of the
rentable floor through at least two access points or doorways originating
from the interior of the structure. The exterior of the building may not be
used as an access point. Additionally, occupants on the lobby floor, or f
=1, should be able to access the exterior of the building through at least
two access points or doorways. A sufficient access point is defined as a
clear opening with the following minimum dimensions:
Width: 1 in.
Height: 2.25 in.
If there is more than one independent floor area for a given floor, the
largest rentable floor area for that floor will count as the only rentable
floor area.
5.6.d Maximum Floor Plan Dimensions

Each floor in violation of the requirements in this section will result in 5
added to V.

The maximum floor plan dimensions are defined in Figure 1 below. All
floors of the model must fit within the specified floor plan dimensions.
Figure 1: Maximum Floor Plan Dimensions
To check this requirement, a template with a cutout of the maximum floor

plan dimensions will be passed over the structural model. Said template
will have a tolerance of 1/16 of an inch in each dimension. The template
shall remain parallel to the top surface of the structural model base plate
as it passes over the structural model. The template cannot be rotated as it
is passed over the structure. The floor(s) where the template cannot freely
pass over will be in violation of this section. Teams will not be allowed to
bend or force the template over any floors.
5.6.e Floor Isolation

Any violation of this section will result in the structural model not being
tested on the shake table and the team disqualified.
Floor isolation of any kind is strictly prohibited. This includes isolating
floor dead loads and the roof plate.
5.7 Structural Model Base Plate

5.7.a Structural Model Base Plate Plan Dimensions
Any dimensional violation in this section greater than 0.25 in. may result
in the judges not allowing the structural model to be tested on the shake

table and, therefore, the model will be assumed collapsed for both ground
motions.
An 18.00 in. by 18.00 in. square continuous wooden (Plywood or MDF)

base plate will be used to attach the model to the shake table. Teams are
responsible for providing a wood base plate. All components of the
structural model shall be centered on the structural base plate, and be no
closer than 1.25 in from the outside edge of the structural model base plate
to allow securing the structural model to the shake table (Section 6.5).
All measurements will be checked with a tape measure or other measuring

device.
5.7.b Structural Model Base Plate Thickness Dimensions

Any dimensional violation in this section resulting in the base plate
thickness falling outside of the indicated range may result in the judges
not allowing the structural model to be tested on the shake table and
assuming the model is collapsed for both ground motions.
The wood base plate shall be between 0.25 in. to 0.50 in. thick.
All measurements will be checked with a caliper.
5.7.c Structural Model Base Plate Requirements

The model will not be tested if the base plate does not meet the
requirements in Sections 5.7.a and 5.7.b. In this case, the model would
be considered collapsed for both ground motions.
Notching the base plate is allowed but only at locations where a frame
member or wall member are in contact with the base plate. The notched
area must be filled in completely with the frame member, wall member,
or glue. Glue may not be present 1/4 in. from the edge of any member
breaking the plane of the top of the base plate visible from the top of the
base plate. Each violation of the requirements for notching the base plate
will result in 5 added to V.
On the top of the base plate, a letter ‘N’ or the word ‘North’ shall be
written with black permanent marker within 1 in. from the North edge and
within 6 in. of the East edge of the base plate.
The bottom of the base plate must be flat and smooth. If the judges deem
the structural model cannot be firmly affixed to the shake table, the
accelerometer will not be attached to the structural model and maximum
damage will be assumed for the first ground motion. If the structural
model cannot be physically attached to the shake table, the structural
model will not be tested, and the structural model will be assumed

collapsed for both ground motions. Failure of the base plate (i.e
delamination, crushing or fracture) that causes the structure to become
unstable, to rock back and forth unattached from the base, or to fall off
the shake table is considered a collapse of the structure.
A hole, no larger than 1/4 in. diameter, may be drilled no further than 2
inches from each corner to secure the structural model for shipping. That
means a total of four holes may be drilled in the base plate for securing
the model to ship.
A second identical wood base plate shall be provided by the team for
judges to weigh in lieu of weighing the base plate attached to the structural
model. The second identical base plate shall have the name of the school
written in black permanent marker. If the judges deem the second base
plate is not identical, the judges will assign the base plate a tare weight of
0.0 lbs. Identical notching is not necessary in the second base plate.
Failure to provide a second identical wood base plate will result in the tare
weight of the plate to be 0.0 lbs. Therefore, the weight of the base plate
will be included in the Structural Model Weight Ws (Section 6.12) used
for scoring purposes.
5.8 Structural Model Roof Plate

The structural model roof plate will be where the accelerometer is attached for
shaking. Care must be taken when designing the roof beams to allow for two C-
clamps to clamp the accelerometer to two diagonally opposing corners of the
structural model roof plate. The structural model roof plate shall be level and centered
on the roof so that the centroid of the roof plate coincides vertically with the centroid
of the base plate. If the judges deem the roof plate is not level or centered, the
accelerometer will not be attached to the model. If the accelerometer cannot be
attached to the model for any reason, the team will receive an APS equal to 100%
(Section 2.2).
5.8.a Structural Model Roof Plate Plan Dimensions

Any dimensional violation in this section greater than 0.25 in. may result
in the judges not allowing the accelerometer to be attached to the
structural model during shaking.
A 6.00 in by 6.00 in square continuous wood roof plate is needed to attach

the accelerometer to the building.
All plan measurements will be checked with a tape measure or other

measuring device.
5.8.b Structural Model Roof Plate Thickness Dimensions

Any dimensional violation resulting in the roof plate thickness falling
outside of the indicated range will result in 20 added to V and may also

result in the judges not allowing the accelerometer to be attached to the
structural model during shaking.
The roof plate thickness shall be between 0.3 in. and 0.4 in. Therefore,
teams are recommended to use 3/8 in. plywood or MDF plates and
independently verify that the measured thickness falls within the indicated
range.
All thickness measurements will be checked with a caliper.
5.8.c Structural Model Roof Plate Requirements

Due to safety concerns, the roof accelerometer will not be attached if
the roof plate does not meet the requirements in Sections 5.8.a and
5.8.b.
Notching the roof plate is allowed, but only at locations where a frame
member or wall member are in contact with the roof plate. The notched
area must be filled in completely with the frame member, wall member,
or glue. Glue may not be present 1/4 in. from any edge of a member
breaking the plane of the bottom of the roof plate visible from the bottom
of the roof plate. Each violation of the requirements for notching the roof
plate will result in 5 added to V.
The top of the roof plate must be flat and smooth. If the judges deem the
accelerometer is not firmly affixed to the structural model using two C-
clamps (scaled drawings of the C-clamps will be provided in the design
guide), the accelerometer will not be attached to the structural model.
A second identical wood roof plate shall be provided by the team for
judges to weigh in lieu of weighing the roof plate attached to the structural
model. The second identical roof plate shall have the name of the school
written in black permanent marker. If the judges deem the second roof
plate is not identical, the judges will assign the roof plate a tare weight of
0.0 lbs. Identical notching is not necessary in the second roof plate. Failure
to provide a second identical wood roof plate will result in the tare weight
of the plate to be 0.0 lbs. Therefore, the weight of the roof plate will be
included in the Structural Model Weight Ws (Section 6.12) used for
scoring purposes.
5.9 Innovative Damping Devices

All damping devices must be approved in the Damping Device Approval Process
(Section 4.2). Any use of a damping device that is not pre-approved or in a pre-
approved location will result in disqualification. The implementation of such a
device needs to allow for the placement of weights as discussed in Section 7.4.

5.10 Building Finish
Any violation of this section will result in the structural model not being tested on
the shake table and the team disqualified.
The finish on all frame and wall members must be bare wood. Paint or other
coatings will not be allowed on any portion of the model. Burned surfaces from
laser cutting are permitted.
5.11 Building Display Requirements

Failure to meet all requirements in this section by the designated time listed in the
schedule will result in 5 added to V. (Section 2.4).
The school name shall be displayed at the top of the building facing all four cardinal
directions (North, East, South, and West), on paper (a non-structural element). The
dimensions of each paper are restricted to 6 in. by 1.5 in.
Each floor must be legibly labeled for judges to see. The floor at the base of the
building is not required to be labeled. The floor above the lobby shall be labeled
‘2’, and so on. The label may be written on the balsa wood structure with a pen or
marker, or small pieces of paper may be attached with the floor labels written on
the pieces of paper. The label must not be designed to assist in the structural
performance or interfere with the installation of the dead weights.
5.12 Structural Model Weight

For scoring purposes, the Structural Model Weight, Ws, is equal to the weight of
the structural model including damping devices but does not include the weight of
the floor dead loads, roof dead load, base plate, or roof plate.
Due to the capacity limits on the shake table, the structural model shall not be
approved for shake table testing and will be deemed collapsed for all ground
motions if the weight of the structural model, damping devices, base plate and
roof plate exceed 5.0lb.
6. Strong Ground Motion Testing
The building will be subjected to two ground motions of increasing intensity. The structural
response to both ground motions will contribute to the annual seismic cost.
6.1 Scaled Ground Motions

Structures will be subjected to 2 scaled and modified ground motions named Ground
Motion 1 and Ground Motion 2. The ground motion records will be available at the
competition website listed on the cover page. The Ground Motions this year are
identical to the Ground Motions from the 2018 competition.

6.2 Shake Table
Structures will be tested on the University Consortium for Instructional Shake Tables
(UCIST) unidirectional earthquake shake table, with plan dimensions of 18.0 in. by
18.0 in.
6.3 Dead Load Specifications

6.3.a Floor Dead Loads
A floor dead load shall be installed at the locations specified in Section 5.5
following the instructions in Section 6.4.a. At the highest relevant floor
specified in Section 5.5, the floor dead load will be represented by a 20 in.
long ½ in. diameter steel threaded rod, 8 plates (Simpson Strong Tie BP
5/8-2), 4 washers and 4 nuts. The individual weight of the rod and total
weight of the floor will be 2.69 [lb]. The remaining floor dead loads will be
represented by a 20 in. long ½ in. diameter steel threaded rods, 4 plates
(Simpson Strong Tie BP 5/8-2), 4 washers and 4 nuts. The total weight of
these individual dead loads is 1.96 [lb].
6.3.b Roof Dead Loads

The roof dead load will be represented by the accelerometer, and two C-
clamps. The two C-clamps will be used to secure the accelerometer to the
structural model roof plate. Each C-clamp has a jaw opening of 1 in. and a
throat opening of 1 in. The total weight of the roof dead load is equal to
0.85 [lb]. The roof dead load will be removed after Ground Motion 1 if the
team elects to not leave the accelerometer in place for Ground Motion 2.
6.4 Dead Load Installation

6.4.a Floor Dead Loads
Each floor dead load shall be securely attached to the structural model at
the floors indicated in Section 5.5.a in the direction perpendicular to
shaking. A floor dead load is defined as secured if it is restricted from
movement in any translational direction after installation (including the
vertical direction). Movement of the floor dead loads can be restricted
with frame or wall members and/or using friction from tightening the nut
at each end of the threaded rod (keep in mind nuts can become loose
during shaking). Each team is responsible for installing and securing the
floor dead loads. See Section 6.9.a for penalties associated with unsecured
floor dead loads.
If a floor dead load connection is not available at a floor required to have

a floor dead load connection, the judge may have the team install a floor
dead load on the required floor and try to secure the floor dead load using
the nuts and washers. If the floor dead load is physically unable to be
installed while centered in plane with the center of the base plate, or if the
judges deem the floor dead load connections are intentionally not
available at a required floor or direction, the model will not be allowed to
be tested and will be assumed collapsed for both ground motions.

Each floor dead load shall be installed by inserting the ½ in. threaded rod
through structural model at the dead load connection locations (Section
5.5). From the building to the end of the threaded rod, the order of the
washers, nuts, and plates for each end of the threaded rod are as follows:
1 washer, 1 nut, 2 plates (per Section 6.3.a), 1 washer, and 1 nut. The nut
immediately following the washer touching the building on each side of
the rod are recommended to be tightened by hand to ensure the floor dead
loads are restricted from movement in any translational direction.
Each team will have at least 8 minutes to install the dead loads. If 8
minutes have passed and the team has not finished installing the floor dead
loads, a penalty of 20 will be added to V. Teams may recruit other non-
team members (excluding SDC Chairs) to assist in installing floor dead
loads.
A SDC Chair shall be present while the team is installing the floor dead
loads to ensure proper installation of the floor dead loads. Another SDC
Chair shall check the floor dead loads before the structural model is
attached to the shake table (Section 6.5). If the SDC Chair finds any
weights free to move in any translational direction, the SDC Chair shall
notify the team captain prior to shaking. The team will have one minute
to tighten the floor dead loads. After one minute, the team will not be able
to make any changes to the structural model or dead loads, shaking shall
commence, and unsecured floor dead loads will be penalized after each
ground motion as described in Section 7.9a.
6.4.b Roof Dead Load

The roof dead load shall be attached to structural model roof plate with
two C-clamps at opposing corners (scaled drawings of the C-clamps will
be provided in the design guide). It is the responsibility of the SDC
Chair(s) to secure the roof dead load to the structural model roof plate
before installing the structural model to the shake table (Section 6.5). The
time required to attach the roof accelerometer will not be included in the
time each team has for installing the dead loads. If the roof dead load is
not level before Ground Motion 1, then the roof dead load will be removed
from the structural model for Ground Motion 1. The roof dead load is
considered not level if the bubble of the level is completely outside of the
lines. See Section 6.9.b for penalties associated with an unsecured or not
level roof dead load.
6.5 Attachment of Structural Model to the Shake Table

SDC Chairs will determine the direction of shaking by flipping a coin prior to the
beginning of shaking. The coin flip will determine if shaking is in the north-south
direction or east-west direction and apply to all structures for the duration of the
competition.

Each team will attach the structural models to the shake table with at least 6 C-clamps
at the corners and center along the two sides of the structural model base plate parallel
with the direction of shaking. Two 18 in. long aluminum angles (1 in. legs and 1/8
in. wall thickness) will span on top of the structural model base plate perpendicular
to the direction of shaking on each side of the building. The two aluminum angles
will be secured with the 4 corner clamps. Two 12 in. long aluminum angles (1 in.
legs and 1/8 in. wall thickness) will span on top of the structural model base plate
parallel to the direction of shaking on each side of the building. The two aluminum
angles will be secured with a center clamp. If the base plate is warped, the corners
of base plate will be clamped so there are no gaps at the corners between the shake
table base, the aluminum angle, and the base plate. A SDC Chair will check each
clamp after installation.
6.6 Instrumentation
Two accelerometers will be used in the competition: one accelerometer will be
attached to the shake table, and the other accelerometer will be part of the roof dead
load (Section 6.3).
6.7 Data Processing

Displacements will be computed from each recorded acceleration time series by
performing the following steps:
1. Transfer the acceleration records into the frequency domain using a Fourier
transform.
2. Digitally high-pass filter the acceleration recordings in the frequency domain using
a 3rd order Butterworth filter with a corner frequency of 0.8 Hz.
3. Transfer the acceleration from the frequency domain to the time domain.
4. Numerically double integrate the filtered acceleration records over time to obtain
displacements.
A portion of the low-frequency range of the raw acceleration signals must be removed
using a digital filter prior to double integration because the low frequency content of
the signals is small compared to the noise. Highly unrealistic displacements would
be obtained if the raw data were integrated in time without first filtering some of the
low frequency content because of the low-frequency noise. An undesired but
unavoidable consequence of the filtering is that the low-frequency portion of the
acceleration signals, which contains permanent displacements, must be removed. As
a result, the displacements computed by double-integrating the acceleration records
are transient displacements; the low-frequency permanent component will not be
reflected in the computed displacement time series.
For each ground motion n, a roof acceleration record, Accln, and absolute roof
displacement record, ΔRoof n, and absolute base displacement record, ΔBase n, will be
available after post-processing.

6.8 Damage Calculations
6.8.a Structural Damage Calculations
Structural damage to the building will be calculated using a function of
the measured peak roof drift, XPeakn. This function is a cumulative
normal probability density function with peak roof drift mean and
standard deviation listed in Section 2.5. The structural damage as a
percentage of the construction cost (XDn) is a function of XPeakn and is
plotted in Figure 7-1.
Tip: The cumulative distribution function can be computed using many

commercially-available software packages (e.g., the NORMDIST
function in Microsoft Excel, with the 'cumulative' field set to TRUE).
0.8
0.6
XDn
0.4
0.2
0
0 0.005 0.01 0.015 0.02 0.025 0.03
XPeakn [%]
Figure 7-1: Function relating peak roof drift, XPeakn, and structural
damage as a percentage of construction cost (XDn)
6.8.b Equipment Damage Calculations

The building is assumed to house equipment that is sensitive to
acceleration. Damage to this equipment will be a function of the measured
roof acceleration, APeakn. This function is a cumulative normal
probability density function with peak roof acceleration mean and
standard deviation listed in Section 2.5. The equipment damage as a
percentage of the equipment cost (XDn) is a function of APeakn and is
plotted in Figure 7-2.

1
0.8
0.6
ADn
0.4
0.2
0
0 0.5 1 1.5 2 2.5 3 3.5
APeakn [g]
Figure 7-2: Function relating peak roof acceleration, APeakn, and

equipment damage as a percentage of equipment cost (ADn)
6.9 Penalties and Determining Collapse
6.9.a Unsecured Floor Dead Load Penalties

After each ground motion, a SDC Chair will inspect the building for any
unsecured floor dead loads (Section 6.4.a). 5% will be added to D for each
unsecured floor dead load. If a penalty D is applied, it will only affect the
monetary structural and equipment damage for the ground motion
immediately following the inspection. If a structural model is deemed
collapsed by a SDC Chair (Section 6.9.c), a penalty D will not be applied
for the ground motion(s) in which the structural model is deemed
collapsed.
For example, if all of the floor dead loads remain secured after Ground
Motion 1, the penalty D for Ground Motion 1 will be equal to 0%. If two
of the floor dead loads are found to be unsecured after Ground Motion 2,
the penalty D for Ground Motion 2 will be equal to 10%.
A floor dead load is considered unsecured:

• If any end of the floor dead load has moved more than ½ in. in any
translational direction from its original pre-shaking location
measured at the exterior face of the building
• If any end of the floor dead load can be moved more than ½ in. in
any translational direction measured at the exterior face of the
building. This includes the vertical direction. The amount of force
applied by the SDC Chair to the floor dead loads will be enough
to check for movement and is at the discretion of that SDC Chair.
• If one floor dead load is in contact with another floor dead load,
both are considered damaged.

6.9.b Unsecured or Not Level Roof Dead Load
Before Ground Motion 1, a SDC Chair will inspect the roof dead load. If
a SDC Chair deems the roof dead load is not secured to the structural
model or not level, the roof dead load will be removed from the structural
model and the score will assume maximum structural and equipment
damage for any of the ground motions where the roof dead load is not
attached to the structural model. An unstable roof plate is not grounds to
declare a structural model collapsed.
6.9.c Defining Collapse of a Structural Model

A SDC Chair deems a structural model has collapsed if any of the
following happens:
▪ 50% or more of the floors are not level

▪ 50% or more of the frame members or walls attached to the base plate
are separated from the base plate or the structural model
▪ 50% or more of the floor dead loads are considered unsecured (Section
6.9.a)
▪ The structural model base plate has delaminated to the point where the
structural model is rocking on the shake table.
The floor levels will be checked with a level. If the whole bubble is
outside of the lines on the level, the floor is considered not level.
The frame members and/or walls attached to the base plate will be visually
inspected to see if separation has occurred between the member and the
base plate and/or the rest of the structural model.
If any of the conditions for collapse are met prior to Ground Motion 1, the
structural model will still be shaken but deemed collapsed for both ground
motions regardless of the outcome after shaking has completed.
If collapse occurs during Ground Motion 1, collapse will be assumed to

happen for Ground Motion 2 for scoring purposes.
7. Score Sheets
All score sheets can be reviewed and signed by the team captain immediately after judging has
completed. Only team captains shall discuss penalties and score sheets with the SDC Chairs
(Section 9).
At the team meeting, the SDC Chairs will indicate a time when team captains can begin to
come by the judging table to review the judging sheets. The indicated time may change
depending on the time required to review all the models.

The SDC Chairs will specify a cut-off time for appeals when the final competition schedule is
released (check the website for updates). After this time, the judges can refuse to review any
score sheets and hear any appeals. The score sheets will be signed by two SDC Chairs and the
penalties assessed can no longer be appealed.
The judging sheet review process will occur as follows:

• The judging sheet will be explained by a SDC Chair to the team captain and only the
team captain.
• The SDC Chair will show the violation(s), if any, on the model.
o If applicable, penalties will be marked with red permanent marker or stickers
on each structural model for quick visual identification.
• A SDC Chair will show the team captain the rule/violation and penalty assessed in the
official rules (or clarifications) if needed.
• If no penalties were found, the team captain may sign the judging sheet or let two SDC
Chairs sign the scoring sheet.
• If a penalty is assessed, a team captain may do one of the following:
o Sign the scoring sheets and forfeit the opportunity to appeal the penalty(s).
o Review the penalties with his or her team members to prepare for an appeal.
▪ The SDC Chair will continue reviewing other team’s scoring sheets and
the team captain will need to wait for the next available SDC Chair for
the appeal.
o Appeal the penalties.
The appeal process is explained in Section 9.1.
Once the scoring sheets have been signed either by the team captain or two SDC Chairs, a team
captain may not make any appeals for the penalties assessed on the scoring sheets already
signed. If a team captain tries to make an appeal for penalties assessed on the scoring sheet(s)
already signed, the team captain will be warned. If after the team captain is warned and they
attempt to continue appealing for penalties assessed on the scoring sheet(s) already signed, the
team will be disqualified.
7.1 Verification of Electronic Score Sheet Entry

Either during or at the end of shaking day, teams will receive a “shaking day score
sheet” via email or hard copy. This score sheet will be a version of the final score
sheet: it will contain information including but not limited to building weight, total
penalties (V), and shake table performance; it will not contain any information about
other scores or bonuses received.
It is the duty of the team captain to review the information on this sheet for
typographical errors. Any such errors, especially those affecting the calculation of
scores, must be reported to the SDC Chairs, either in person or by email, before 9:00
PM competition local time of the evening before the awards ceremony. The SDC
Chairs will review the hard-copy score sheets, and will rectify any errors that are
reported in this way. If a team captain has not reported any errors by the deadline, it

is assumed that they have reviewed their score sheet and accept all information as
typographically accurate.
Please note that this is not an opportunity to initiate any appeals (Section 9), or to
dispute the scores in any other way. This is only an opportunity to verify that the
information entered electronically is typographically consistent with the information
recorded on hard-copy (which has already been signed by the team captain or two
SDC Chairs, as explained above).
8. Rule Clarifications
All rule clarification requests and answers will be posted on the competition website. The
posted question and answer will also include the name of the school submitting the question.
To submit a rule clarification, the team captain must fill out and submit an online submission
form, which can be found on the competition website. Questions or clarifications about the
rules sent via email will not be answered. Be sure to read the rules, guide, and any other current-
year clarifications thoroughly before submitting a question.
9. Judging and Appeals
The SDC Chairs have complete authority over the interpretation of the rules and oversight of
the competition and are responsible for scoring and decisions. All decisions made by the SDC
Chairs are final. If any questions arise during the competition, the team captain should ask one
of the SDC Chairs, not other SLC members.
Only a team captain may discuss decisions or appeals to SDC Chairs. SDC Chairs will refuse
to discuss a decision or appeal to anyone other than the team captain. A team captain may only
make an appeal regarding his or her team.
Under no circumstances may anyone other than the team captain approach a SDC Chair
regarding penalties or scoring. This includes but is not limited to other teammates, alumni,
professors, and especially other SLC members. If this becomes an issue, the team captain will
be warned, and in extreme cases, the SDC Chairs reserve the right to disqualify the team.
The SDC Chairs are not out to assess extraneous penalties. During judging process, the judges
are trained and supervised to evaluate all of the structural models for the same requirement(s)
so there is a consistency in judging. Please be considerate and respectful to the SDC Chairs
when making an appeal. The SDC Chairs strive to be fair and consistent with all teams
regarding the official rules.
9.1 Appeals Process

A team captain can make an appeal about a penalty or decision before signing a score
sheet. An appeal begins the very instant the team captain questions the penalty(s) to

a Seismic Design Competition Chair(s). Only one appeal per team can be made for
all penalties assessed. The team captain must explain using the official rules and
clarifications why the penalty or decision should be changed. A SDC Chair will hear
the team captain’s appeal and may consult other SDC Chairs before making a final
decision. After a final decision has been made by the Seismic Design Competition
Chair(s), the team captain cannot appeal the penalty any further. If the team captain
refuses to sign the score sheet, two SDC Chairs will sign the score sheet instead and
the score sheet will be considered signed by the team captain.
In the interest of time, no appeals are allowed once shaking of the structures has
begun. The team captain may ask for an explanation on why their structure was
determined collapsed, but the buildings must be tested and moved along.
9.2 Rule Modifications

In very rare cases, unexpected circumstances may arise that threaten the spirit of the
competition. In these cases, the Seismic Design Competition Chair(s) reserve the
right to modify the rules, if such a modification would preserve the quality of the
competition.
10. Code of Conduct and Plagiarism

The SDC Chairs and other SLC members understand that teams have worked very hard to
compete in the event, but would also like the teams to recognize that they, too, have worked
very hard to organize and run the event. As such, individuals who treat the SLC with extreme
disrespect may be dismissed from the tournament, and their team may also be disqualified
from the tournament. Individuals include but are not limited to teammates, team advisors,
alumni, professors, and team sponsors.
Plagiarism is strictly prohibited throughout the competition. Taken from [1], examples of
plagiarism include:
• Taking credit for any work created by another person.
• Copying any work belonging to another person without indicating that the information
is copied and properly citing the source of the work.
• If not directly copied, using another person’s presentation of ideas without putting it in
your own words or form and not giving proper citation
• Creating false citations that do not correspond to the information you have used.
So-called common knowledge does not need to be cited; for more information, see [2].
[1] OSSJA (2016). “UC Davis Code of Academic Conduct.”

<http://sja.ucdavis.edu/cac.html>.
[2] MIT (2016). “What is Common Knowledge.”

<https://integrity.mit.edu/handbook/citing-your-sources/what-common-knowledge>.

2019 SDC Official Rules

Uploaded by

Copyright:

Available Formats

2019 SDC Official Rules

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2019 SDC Official Rules

Uploaded by

Copyright:

Available Formats

Sixteenth Annual Undergraduate

Seismic Design Competition (SDC)

Organized and Run by:

Competition Website: https://slc.eeri.org/2019-seismic-design-competition/

2019 Undergraduate Seismic Design Competition- Rules 2

2019 Undergraduate Seismic Design Competition- Rules 3

1.2 Problem Statement

2019 Undergraduate Seismic Design Competition- Rules 4

A cost-benefit analysis will be carried out to determine the most cost-effective

2019 Undergraduate Seismic Design Competition- Rules 5

The number of teams invited to participate in the competition will be determined by

Team registration and eligibility questions should be directed to:

1.3.a Team Eligibility Requirements

▪ Teams must be affiliated with a registered EERI student chapter in

2019 Undergraduate Seismic Design Competition- Rules 6

1.3.b Team Registration Requirements

▪ Proposal Submittal (Section 5)

1.3.c Important Deadlines and Deliverables

Teams will be invited to participate by November 19th, 2018.

1.5 Summary of Notable Rule Changes for this Year

▪ Predictions are required for both shaking directions.

2019 Undergraduate Seismic Design Competition- Rules 7

2.1 Design Proposal, Presentation, Poster, and Architecture

A projector and laptop, running Microsoft Windows 7 or newer, and

2019 Undergraduate Seismic Design Competition- Rules 8

Presentations shall include the following:

• Name of school on title slide

The poster shall include the following:

• Name of school (font size 40 recommended)

2019 Undergraduate Seismic Design Competition- Rules 9

2.1.d Bonus Scoring

Table 2-1: Annual Revenue Bonus

Rank Proposal Presentation Poster Architecture

2.2 Performance Predictions and Floor Area Calculations

2019 Undergraduate Seismic Design Competition- Rules 10

The performance predictions must be submitted by the deadline listed on the

2.2.a Performance Predictions Requirements

𝐷𝑖𝑠𝑝𝑛 𝑃𝑟𝑒𝑑𝑖𝑐𝑡𝑒𝑑 = max|Δ𝑅𝑜𝑜𝑓 𝑛 𝑃𝑟𝑒𝑑𝑖𝑐𝑡𝑒𝑑 [𝑖𝑛] − Δ𝐵𝑎𝑠𝑒 𝑛 𝑃𝑟𝑒𝑑𝑖𝑐𝑡𝑒𝑑 [𝑖𝑛]|

|𝐴𝑐𝑐𝑙1 𝑃𝑟𝑒𝑑𝑖𝑐𝑡𝑒𝑑 − 𝐴𝑃𝑒𝑎𝑘1 |

𝐴𝑃𝑆 = 𝐴𝑃𝑆1 + 𝐴𝑃𝑆2

2019 Undergraduate Seismic Design Competition- Rules 11

Rank APS Bonus

2.2.b Floor Area Calculations

2.3 Annual Revenue

$250 per year per square inch for floors 1 through 2

2.4 Annual Building Cost

𝐴𝑑𝑑𝑖𝑡𝑖𝑜𝑛𝑎𝑙 𝐶𝑜𝑛𝑠𝑡𝑟𝑢𝑐𝑡𝑖𝑜𝑛 𝐶𝑜𝑠𝑡 = 𝐶𝑎 = 200,000 [$] × 𝑉

𝐷𝑎𝑚𝑝𝑖𝑛𝑔 𝐷𝑒𝑣𝑖𝑐𝑒(𝑠) 𝐶𝑜𝑠𝑡 = 𝐶𝑑 = (0.00625 × 𝑁𝑑 + 0.0125) × 𝐶𝑐 if 𝑁𝑑 ≤ 10.

2019 Undergraduate Seismic Design Competition- Rules 12

𝐷𝑒𝑠𝑖𝑔𝑛 𝐿𝑖𝑓𝑒 = 100 [𝑦𝑒𝑎𝑟𝑠]

𝐶𝑐 [$] + 𝐶𝑎 [$] + 𝐶𝑑 [$] + 𝐿𝑎𝑛𝑑 𝐶𝑜𝑠𝑡[$]

2.5 Annual Seismic Cost

𝐸𝑞𝑢𝑖𝑝𝑚𝑒𝑛𝑡 𝐶𝑜𝑠𝑡 = 20,000,000 [$]

𝑅𝑒𝑡𝑢𝑟𝑛 𝑃𝑒𝑟𝑖𝑜𝑑1 = 50 [𝑦𝑒𝑎𝑟𝑠]

𝑋𝐷𝑛 = 𝐶𝐷𝐹(𝜇𝑋 [%], 𝜎𝑋 [%], 𝑋𝑃𝑒𝑎𝑘𝑛 [%])

2019 Undergraduate Seismic Design Competition- Rules 13

max|Δ𝑅𝑜𝑜𝑓 𝑛 [𝑖𝑛] − Δ𝐵𝑎𝑠𝑒 𝑛 [𝑖𝑛]|

𝐴𝑃𝑒𝑎𝑘𝑛 = max|𝐴𝑐𝑐𝑙𝑛 [𝑔]|

𝐸𝑐𝑜𝑛𝑜𝑚𝑖𝑐 𝐿𝑜𝑠𝑠𝑛 = 𝑋𝐷𝑛 [%] × 𝐶𝑜𝑛𝑠𝑡𝑟𝑢𝑐𝑡𝑖𝑜𝑛 𝐶𝑜𝑠𝑡[$]