1-LTE Drive Test Post Processing Overview PDF

1.
LTE Drive Test Post Processing Overview
Author : Ray Khastur

Title : LTE Optimization Consultant
Consulting | Training | Research
1.1 Post Processing Overview
Actix Overview

How to Load Logfile’s

What is Super Stream ?
Super
Logfile 1 Stream
.
.
.
Logfile N
A superstream is a new stream created by merging two or more sets of data into
one large data set. Beware that the size can be huge (since the superstream
contains all attributes, even those that we might not need in our analysis).

How to Create Superstream

Display all required information (1)
On the Superstream Attribute,

breakdown the information that we
want to show into (Map, Chart or Table)

6 All Detail Information

RSRP Level

Layer 3 Message

Complete Analysis Template

Limitation
• Actix suitable for TEMS, NEMO and XCAL Logfile.
• For HUAWEI Genex Probe only suitable by using
Genex Assistant.

1.2 Drivetest Reporting on Accessibility
Performance
Accessibility Performance
Attach Full 3
Layer
message

Accessibility Performance (RRC)
RRC SSR[%]=
RRCConnectionSetupOK/RRR
CConnectionAttempt*100%
RRC Connection Setup, not

No RRC Setup Failure relevant with the
in this report, RRCConSetupComplete
message
RRC SSR 100%

Conclusion of Accessibility Performance
• This method should be taken from short call Logfile.
RRC Attempt
RRC Success
RRC Fail
• 3 Layer message available for analysis.

1.2 Drivetest Reporting on Mobility
Performance
Measurement Event

Parameter Configuration (Intra-Frequency
Handover)
Source Target
UE
eNB eNB
Handover-related parameters are used to control the reporting time and
1.A3 Measurement Control
difficulty level of a handover in the measurement report. For details about
handover parameter configuration, see
Measure RSRP/RSRQ
eRAN3.0 Handover-related MML Command Configuration Guide
•Intra-frequency handover triggering process (event A3) A3 EventTriger
Mn  Ofn  Ocn  Hys  Ms  Ofs  Ocs  Off A3 Measurement

➢Mn indicates the measured Reference Signal Received Power (RSRP) 2.
Reports
and Reference Signal Received Quality (RSRQ) of neighboring cells.
Handover preparation
➢Ofn indicates the frequency offset.
RRC Conn. Reconf. incl.
3
➢Ocn indicates the neighboring-cell offset to be configured through the mobilityControlinformation
neighboring relationship.
➢Ms indicates the measured RSRP and RSRQ of the serving cell. Random access procedure
➢Ofs indicates the offset of the serving frequency. 4 RRC Conn. Reconf. Complete
➢Ocs indicates the offset of the serving cell.
➢Hys indicates the hysteresis, closely related to the service feature and
the mobility speed.
Reducing the probability of ping-pong effect.
➢Off a3-Offset
➢Mn, Ms is in units of dBm or dB. Other parameters are in units of dB.

Handover)
Mn  Ofn  Ocn  Hys  Ms  Ofs  Ocs  Off
How strong needed, for

RSRP Neighbour to
perform Intrafreq HO
Execution ?
Serving eNB Target eNB

Alamanda M-I-GF RC Veteran M-S-RT

Handover)

Handover)

Handover)
Also called as CIO

Handover)

Handover)
How strong needed, for

RSRP Neighbour to
perform Intrafreq HO
Execution ?
Serving eNB Target eNB

Alamanda M-I-GF RC Veteran M-S-RT
Mn + 0 dB + 0 dB – 1 dB > -90 dBm + 0 dB + 0 dB + 1 dB

Mn > -90 dBm + 2 dB
Mn > -88 dBm
So, need more than +2 dB to perform Intrafreq HO in event A3

Handover)
To reduce Ping Pong effect, there is time to

trigger to allowed Intrafreq HO

Mobility Performance
IntraFreq HOSR InterFreq HOSR

100% 100%

Signaling Flow for Handover

Mobility Performance (Measurement Report)
In this case there are Event A3

measurement report. Which showing
Neighbor RSRP(-72 dBm) bigger than
Serving RSRP(-77 dBm)

Mobility Performance (RRC Connection
Reconfiguration)
Important thing in this Layer 3

message there are: Target PCI, Target
DL EARFCN, RSI Information, and RS
Power from Target eNB

Reconfiguration)

message there are: Preamble Index
assignment, transmission mode, TDD
Ratio configuration,

Reconfiguration)

message there are: Chippering and
Integrity Protection Algorithm

Reconfiguration Complete)

message there are: Information of
successful Handover Process. And on
below that message contain RACH
Contention Free information during
HO Process.

Conclusion of Mobility Performance
• This method should be taken from long call Logfile.
Intrafreq
Interfreq

1.3 Drivetest Reporting on Integrity
Performance
What is Integrity Performance ?
Why Internet in Indonesia so slow?

From each Network
Element has different
capacity pipeline,
causing Integrity
performance so bad
Mbps
500
1 Gbps 1 Gbps

Optimization LTE not
only RF Parts, so we
have to cooperate to fix
it on entire Network
4 Gbps
Element
1 Gbps 1 Gbps

Introduction of LTE Radio Protocol Stack
• Two Planes in LTE Radio Protocol:  Main Functions of Control-plane:
– User-plane: For user data transfer  RLC and MAC layers perform the same functions
as for the user plane
– Control-plane: For system
 PDCP layer performs ciphering and integrity
signaling transfer
protection
 RRC layer performs broadcast, paging, connection
• Main Functions of User-plane: management, RB control, mobility functions, UE
measurement reporting and control
– Header Compression
 NAS layer performs EPS bearer management,
– Ciphering authentication, security control
Control-plane protocol stack
– Scheduling
UE eNB MME
– ARQ/HARQ
User-plane protocol stack NAS NAS
UE eNB RRC RRC
PDCP PDCP PDCP PDCP
RLC RLC RLC RLC
MAC MAC MAC MAC
PHY PHY PHY PHY

Physical Layer DL Throughput



Throughput Chart

DL Throughput Performance

Mac DL Throughput Result

DL PRB Utilization
High PRB Utilization for TD-LTE

15 MHz

DL Scheduling Parameter
Can be set as Using DL MIMO

EPF/PF/RR/MaxCI 2x2

Antenna Configuration
Antenna set as
4T4R

Rank Indicator
In simple words, RI is an indicator showing how well multiple Antenna work. What do you mean by "how well the multiple Antenna work ?". We usually say
"Each of the multiple antenna (e.g, each antenna in MIMO configuration) works well if the signal from each antenna has NO correlation to each other". "No
correlation" implies "no interference to each other".
Maxmum RI value is very closely related to the number of Antenna. Maximum RI is same as number of antenna on each side if the number of Tx antenna and
Rx antenna is same. If the number of Tx and Rx are different, the one with less antenna is the same as Max achievable RI.
Max RI means "No Correlation between the antenna", "No interference to each other", "Best Performance".
For example, in case of 2x2 MIMO, the RI value can be 1 or 2. When the value 2 in this case means "No Correlation between the antenna", "No interference to
each other", "Best Performance". If the value is 1, it implies that the signal from the two Tx antenna is percieved by UE to be like single signal from single
Antenna, which means the worst performance.

CQI Comparison
Afternoon 16:00 Midnight 02:00

CQI Comparison

DL Throughput Comparison
Afternoon 16:00 Midnight 02:00
During Low Utilization of DL PRB on Cell Level give benefit for single UE can get higher
DL PRB which is related to the Higher DL Throughput.
DL Throughput Comparison
During Low Utilization of DL PRB on Cell Level give benefit for single UE can get higher
DL PRB which is related to the Higher DL Throughput.

CQI to MCS
CQI stands for Channel Quality Indicator. As the name implies,
it is an indicator carrying the information on how good/bad the
communication channel quality is. This CQI is for HSDPA. (LTE
also has CQI for its own purpose).
CQI is the information that UE sends to the network and

practically it implies the following two
i) Current Communication Channel Quality is this-and-that..
ii) I (UE) wants to get the data with this-and-that transport block
size, which in turn can be directly converted into throughput
Page 54 Consulting | Training | Research

Conclusion of Integrity Performance
• This method should be taken from long call Logfile.
• There is no specific Layer 3 message available for analysis.
DL Throughput
UL Throughput

1.4 Drivetest Reporting on Retainability
Performance
Measurement Event
Drop event happen after UE

have been connected.
RRC Attempt
RRC Connected
Drop Event

Drop Rate Calculation
Drop Rate % :
RRCConnection_ReestablishmentFailed/RRCConnectionSetupOK*
100%
Drop Rate : 1/116*100%

: 0.86%

RRC Reestablishment Request

RRC Reestablishment Reject
From the drive test result shown that, minimum RSRQ value are below the allowable
minimum threshold at -18 dB (U2000 Configuration)

Cell Selection Configuration

Conclusion of Retainability Performance
• This method should be taken from short call Logfile.

Thank You

1-LTE Drive Test Post Processing Overview PDF

Uploaded by

Copyright:

Available Formats

1-LTE Drive Test Post Processing Overview PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1-LTE Drive Test Post Processing Overview PDF

Uploaded by

Copyright:

Available Formats

1.

LTE Drive Test Post Processing Overview

Author : Ray Khastur

Consulting | Training | Research

Consulting | Training | Research

Consulting | Training | Research

Consulting | Training | Research

On the Superstream Attribute,

Consulting | Training | Research

6 All Detail Information

Consulting | Training | Research

Consulting | Training | Research

Consulting | Training | Research

Consulting | Training | Research

Consulting | Training | Research

Consulting | Training | Research

RRC Connection Setup, not

Consulting | Training | Research

• 3 Layer message available for analysis.

Consulting | Training | Research

Consulting | Training | Research

Mn  Ofn  Ocn  Hys  Ms  Ofs  Ocs  Off A3 Measurement

Consulting | Training | Research

How strong needed, for

Serving eNB Target eNB

Consulting | Training | Research

Consulting | Training | Research

Consulting | Training | Research

Also called as CIO

Consulting | Training | Research

Consulting | Training | Research

How strong needed, for

Serving eNB Target eNB

Mn + 0 dB + 0 dB – 1 dB > -90 dBm + 0 dB + 0 dB + 1 dB

So, need more than +2 dB to perform Intrafreq HO in event A3

Consulting | Training | Research

To reduce Ping Pong effect, there is time to

Consulting | Training | Research

IntraFreq HOSR InterFreq HOSR

Consulting | Training | Research

Consulting | Training | Research

In this case there are Event A3

Consulting | Training | Research

Important thing in this Layer 3

Consulting | Training | Research

Important thing in this Layer 3

Consulting | Training | Research

Important thing in this Layer 3

Consulting | Training | Research

Important thing in this Layer 3

Consulting | Training | Research

Consulting | Training | Research

Why Internet in Indonesia so slow?

Consulting | Training | Research

Consulting | Training | Research

Consulting | Training | Research

UE eNB RRC RRC

PDCP PDCP PDCP PDCP

RLC RLC RLC RLC