0% found this document useful (0 votes)
2K views

How To Install + Crack

1. Disconnect from the internet and download, unzip, and run the installation file with Administrator access using the provided serial key. 2. Select "Single License Server" and enter "127.0.0.1" when prompted for license server details during installation. 3. Download the crack file separately, convert license files to the correct architecture, replace existing files, edit the lic.dat file with your system details, and start the license manager to activate the full version of the software.
Copyright
© © All Rights Reserved
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
2K views

How To Install + Crack

1. Disconnect from the internet and download, unzip, and run the installation file with Administrator access using the provided serial key. 2. Select "Single License Server" and enter "127.0.0.1" when prompted for license server details during installation. 3. Download the crack file separately, convert license files to the correct architecture, replace existing files, edit the lic.dat file with your system details, and start the license manager to activate the full version of the software.
Copyright
© © All Rights Reserved
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

Installation guide

1. It is best to disconnect your Internet connection before installing.


2. Download the software and unzip it.

3. Run the 001_003.sfx.exe file with Administrator access and allow the software to
be extracted in the default path; then the software installation process starts
automatically.

4. At the Serial request, enter one of these codes:

666-69696969
667-98989898
400-45454545

Then enter the serial Product Key below: (if necessary)


797K1 (for Inventor Professional)
208K1 (for Inventor)
529K1 (for Inventor LT)

5. For Select your License server model, select Single License Server from the
drop-down menu and enter 127.0.0.1 for the server name. If you receive a message on
the license file, ignore them and install the installation process. (For example,
click on Continue)

6. It is best to block an Internet firewall from accessing the software.

7. Download and open the Crack file separately.

8. From within the Crack folder, refer to the appropriate x86 or x64 folder for
your system architecture.
8.1. Convert one of the two nlm.msi files to their system architecture (for 32-bit
systems nlm11.14.1.3_ipv4_ipv6_win32.msi and for 64-bit systems
nlm11.14.1.3_ipv4_ipv6_win64.msi) with Run Administrator access and License program
Install the manager (you must right-click on the file and click Run as
administrator)

.8-2- Copy and replace the existing file in adskflex.exe file in C: \ Autodesk \
Network License Manager.

8.3. Copy and replace the existing file in adlmint.dll file in C: \ Program
Files \ Common Files \ Autodesk Shared \ CLM \ V7 \ MSVC14.

9. Open the lic.dat file (available in the Crack folder) through Notepad. Change
the license file to fit your system, so that instead of HOSTNAME and MAC, put the
values ??appropriate for your system as follows:
9.1. Run the LMTOOLS Utility program (now installed on your system). In the System
Settings tab, place the value displayed in front of the computer / hostname instead
of the HOSTNAME and the value displayed against the Ethernet instead of the MAC
USE_SERVER in the lic.dat file.
9.2. Finally, add the value in the License edite file to the end of the content
contained in the lic.dat (copy all the entries from the beginning to the end), and
then save the changes.
9.3. Copy the lic.dat file to C drive.

10. Run the LMTOOLS Utility program. (Lmtools.exe file) 10-1.


Refer to the config services tab.
- In the Service Name, type the word Autodesk.
- In front of Path to lmgrd File, enter C: \ Autodesk \ Network License Manager \
lmgrd.exe.
- Enter the C: \ lic.dat versus Path to license file
- check the start server at power up and use services options.
- Click Save Servise.

10-2. Refer to the service / license file tab. Select the configuration using
services option.
Select the LMtools ignore option file path env var. (Check).

10-3. Refer to the start / stop / read tab. Click on the start server, and then
rereadlicense file, and wait for each of them to complete their operation.

10-4. Refer to the status server tab. Click on perform status enquiry.

11. Run the software.

Attention: If you fail to choose the type of license during installation, then
click Multi-User after running the software. For Select your License server model,
select the Single License Server option from the drop-down menu and enter 127.0.0.1
for the server name.

You might also like