Product Specification

AU OPTRONICS CORPORATION

( V ) Preliminary Specifications
( ) Final Specifications

Module 13.3” HD Color TFT-LCD

Model Name B133XW01 V2 (H/W:0A)

Note ( ) LED Backlight with driving circuit design

Customer Date Approved by Date

Bonnie Chen 4 th Mar, 2009

Checked &
Approved by Date Prepared by

Vicki Chai 4 th Mar, 2009

Note: This Specification is subject to change without NBBU Marketing Division /

notice. AU Optronics corporation

B133XW01 V2 Document version: 0.2 1 of 34

 Product Specification
AU OPTRONICS CORPORATION

Contents
1. Handling Precautions....................................................................................... 4
2. General Description.......................................................................................... 5
2.1 General Specification......................................................................................................... 5
2.2 Optical Characteristics ....................................................................................................... 6
3. Functional Block Diagram.............................................................................. 11
4. Absolute Maximum Ratings........................................................................... 12
4.1 Absolute Ratings of TFT LCD Module ............................................................................. 12
4.2 Absolute Ratings of Environment..................................................................................... 12

5. Electrical characteristics ............................................................................... 13

5.1 TFT LCD Module ............................................................................................................. 13
5.2 Backlight Unit................................................................................................................... 15

6. Signal Characteristic ...................................................................................... 16

6.1 Pixel Format Image.......................................................................................................... 16
6.2 The input data format....................................................................................................... 17
6.3 Integration Interface and Pin Assignment ........................................................................ 18
6.4 Interface Timing ............................................................................................................... 22

7. Connector Description ................................................................................... 24

7.1 TFT LCD Module ............................................................................................................. 24
8. LED Driving Specification .............................................................................. 25
8.1 Connector Description ..................................................................................................... 25
8.2 Pin Assignment ................................................................................................................ 25

9. Vibration and Shock Test............................................................................... 26

9.1 Vibration Test ................................................................................................................... 26
9.2 Shock Test Spec: ............................................................................................................. 26

10. Reliability....................................................................................................... 27
11. Mechanical Characteristics ......................................................................... 28
11.1 LCM Outline Dimension ................................................................................................. 28
12. Shipping and Package ................................................................................. 30
12.1 Shipping Label Format................................................................................................... 30
12.2 Carton package ............................................................................................................. 31
12.3 Shipping package of palletizing sequence...................................... 錯誤 尚未定義書籤。錯誤! 尚未定義書籤。

13. Appendix: EDID description......................................................................... 31

B133XW01 V2 Document version: 0.2 2 of 34

 Product Specification
AU OPTRONICS CORPORATION

Record of Revision

Version and Date Page Old description New Description Remark

0.1 2008/10/31 All First Edition for Customer

0.2 2009/03/04 5 Power consumption = TBD Power consumption = 4.8W max

5-6 Response time = 12ms max Response time = 16ms max

6 Cross talk = TBD Cross talk = 4%

Color spec = TBD Color spec updated

15 PLED = TBD PLED = 3.8W max

19 LED Power Supply 7V-20V LED Power Supply 6V-21V

20 Rear view drawing Rear view drawing updated

25 LED Power Supply 7V-20V LED Power Supply 6V-21V

28-29 2D drawing 2D drawing updated

30-31 TBD Shipping and packing updated

32-34 TBD EDID added

B133XW01 V2 Document version: 0.2 3 of 34

 Product Specification
AU OPTRONICS CORPORATION

1. Handling Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input
connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration
or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on
hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate
nor tilt the Interface Connector of the TFT Module.
10) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
11) Small amount of materials having no flammability grade is used in the LCD module.
The LCD module should be supplied by power complied with requirements of
Limited Power Source (IEC60950 or UL1950), or be applied exemption.
12) Disconnecting power supply before handling LCD modules, it can prevent electric
shock, DO NOT TOUCH the electrode parts, cables, connectors and LED circuit
part of TFT module that a LED light bar build in as a light source of back light unit.
It can prevent electrostatic breakdown.

B133XW01 V2 Document version: 0.2 4 of 34

 Product Specification
AU OPTRONICS CORPORATION

2. General Description
B133XW01 V2 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel,
a driver circuit, and LED backlight system. The screen format is intended to support the High
Definition (1366(H) x 768(V)) screen and 262k colors (RGB 6-bits data driver) with LED
backlight driving circuit. All input signals are LVDS interface compatible.

B133XW01 V2 is designed for a display unit of notebook style personal computer and
industrial machine.

2.1 General Specification

The following items are characteristics summary on the table at 25 condition:

Items Unit Specifications

Screen Diagonal [mm] 336.6 (13.25W”)

Active Area [mm] 293.42 X 164.97

Pixels H x V 1366x3(RGB) x 768

Pixel Pitch [mm] 0.2148X0.2148

Pixel Format R.G.B. Vertical Stripe

Display Mode Normally White

White Luminance (ILED=20mA) [cd/m2] 220 typ. (5 points average)

(Note: ILED is LED current) 187 min. (5 points average)
1.25 max. (5 points)
Luminance Uniformity 500 typ
Contrast Ratio 8 typ / 16 Max
Response Time
[ms]
Nominal Input Voltage VDD [Volt] +3.3 typ.

Power Consumption [Watt] 4.8W

Weight [Grams] 315 max.
L W T
Physical Size
Max 306.8 193.83 3.8
[mm]
Typical - - -
Min - - -
Electrical Interface 1 channel LVDS
Glass thickness [mm] 0.5
Anti-fouling, Glare, Hardness 3H,
Surface Treatment Reflection 4.3%

B133XW01 V2 Document version: 0.2 5 of 34

 Product Specification
AU OPTRONICS CORPORATION

Support Color 262K colors ( RGB 6-bit )

Temperature Range
Operating [oC] 0 to +50
Storage (Non-Operating) [oC] -20 to +60

RoHS Compliance RoHS Compliance

2.2 Optical Characteristics

The optical characteristics are measured under stable conditions at 25 (Room Temperature) :

Item Unit Conditions Min. Typ. Max. Note

2
White Luminance [cd/m ] 5 points average 1, 4, 5.
(ILED=20mA) 187 220 -

Horizontal 4, 9
[degree] (Right) - 45 -
[degree] CR = 10(Left) - 45 -
Viewing Angle Vertical
[degree] (Upper) - 15 -
[degree] CR = 10 (Lower) - 35 -
5 Points
Luminance - - 1.25 1, 3, 4
Uniformity
13 Points - - 1.5 2, 3, 4

CR: Contrast Ratio 400 500 - 4, 6

Cross talk % 4 4, 7
Response Time [msec] Rising + Falling - 8 16
Red x 0.555 0.585 0.615
Red y 0.305 0.335 0.365
Green x 0.300 0.330 0.360
Green y 0.545 0.575 0.605 4, 9
Chromaticity of color Blue x 0.125 0.155 0.185
Coordinates
(CIE 1931) Blue y 0.100 0.130 0.160
White x 0.283 0.313 0.343
White y 0.299 0.329 0.359

B133XW01 V2 Document version: 0.2 6 of 34

 Product Specification
AU OPTRONICS CORPORATION

Note 1: 5 points position (Ref: Active area)

W /4 W /4 W /4 W /4

H /4

1 2

H /4

H 3

H /4

4 5

H /4

Note 2: 13 points position (Ref: Active area)

W /4 W /4 W /4 W /4

10 10

10
1 2 3
H /4

4 5

H /4

H 6 7 8

H /4

9 10

H /4 11 12 13
10

Note 3: The luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the
minimum test point luminance

Maximum Brightness of five points

=
δ W5
Minimum Brightness of five points

Maximum Brightness of thirteen points

=
δ W 13
Minimum Brightness of thirteen points

Note 4: Measurement method

The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change
during measuring. In order to stabilize the luminance, the measurement should be executed after lighting

B133XW01 V2 Document version: 0.2 7 of 34

 Product Specification
AU OPTRONICS CORPORATION

Backlight for 30 minutes in a stable, windless and dark room.

Photo detector

Field=2
°

50 cm

LCD Panel TFT-LCD Module

Center of the screen

Note 5 Definition of Average Luminance of White (YL):

：
Measure the luminance of gray level 63 at 5 points YL = [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5
，
L (x) is corresponding to the luminance of the point X at Figure in Note (1).

Note 6 Definition of contrast ratio:

： Contrast ratio is calculated with the following formula.

Brightness on the “White” state

Contrast ratio (CR)=
Brightness on the “Black” state

Note 7 Definition of Cross Talk (CT)

：
CT = | YB – YA | / YA × 100 (%)

Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)

YB = Luminance of measured location with gray level 0 pattern (cd/m2)

B133XW01 V2 Document version: 0.2 8 of 34

 Product Specification
AU OPTRONICS CORPORATION

Note 8: Definition of response time:

The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to
“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time interval between
the 10% and 90% of amplitudes. Refer to figure as below.

"Black"
"White" "White"
100%
90%
Signal(Relati
ve value)

10%
0%
Tr Tf

B133XW01 V2 Document version: 0.2 9 of 34

 Product Specification
AU OPTRONICS CORPORATION

Note 9. Definition of viewing angle

Viewing angle is the measurement of contrast ratio 10, at the screen center, over a 180° horizontal and

180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90°

(θ) horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement direction is
typically perpendicular to the display surface with the screen rotated about its center to develop the desired
measurement viewing angle.

B133XW01 V2 Document version: 0.2 10 of 34

 Product Specification
AU OPTRONICS CORPORATION

3. Functional Block Diagram

The following diagram shows the functional block of the 13.3 inches wide Color TFT/LCD Module:

LCD Connector(40pin)
IPEX 20455-040E-12
Mating Housing IPEX 20453-040T-01 X -Driver

Y-Driver
LCD DRI VE Board
(4 pairs LVDS)
RxIN 0
RxIN 1
LCD
RxIN 2
RxCLKIN
TFT ARRAY/CELL
C ontr ol ler
1366(R/G/B) x 3 x 768

DC-DC
C onv erter
LE D Pow er

VDD LED circuit

LED Light B ar
GND

B133XW01 V2 Document version: 0.2 11 of 34

 Product Specification
AU OPTRONICS CORPORATION

4. Absolute Maximum Ratings

An absolute maximum rating of the module is as following:

4.1 Absolute Ratings of TFT LCD Module

Item Symbol Min Max Unit Conditions
Logic/LCD Drive Voltage Vin -0.3 +4.0 [Volt] Note 1,2

4.2 Absolute Ratings of Environment

Item Symbol Min Max Unit Conditions
o
Operating Temperature TOP 0 +50 [ C] Note 4
Operation Humidity HOP 10 90 [%RH] Note 4
o
Storage Temperature TST -20 +60 [ C] Note 4
Storage Humidity HST 10 90 [%RH] Note 4

Note 1: At Ta (25 )

Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: LED specification refer to section 5.2
Note 4: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).

B133XW01 V2 Document version: 0.2 12 of 34

 Product Specification
AU OPTRONICS CORPORATION

5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows;

Symble Parameter Min Typ Max Units Note

VDD Logic/LCD Drive 3.0 3.3 3.6 [Volt]
Voltage
VDD Power
PDD - - 0.9 [Watt] Note 1/2
IDD Current
IDD - [mA]
- 300 Note 1/2
IRush Inrush Current 2000 [mA]
- - Note 3
VDDrp Allowable - -
100 [mV]
Logic/LCD Drive p-p
Ripple Voltage

Note 1 : Maximum Measurement Condition Black Pattern

：
Note 2 Typical Measurement Condition: Mosaic Pattern
：
Note 3 Measure Condition

： +5.0V Q3
AO6402
D6 F1
D5
D2 S
D1 VCC

R1 (LCD Module Input)

47K G
C1
1uF/16V
(High to Low)
D1D2D5D6
Control
Signal Q3
R2 AO6402
G

1K S
C3
2 +12.0V
SW1
SW MAG-SPST VR1 0.01uF/25V
1 47K

C2
1uF/25V

90% 3.3V

10%
0V
0.5ms

Vin rising time

B133XW01 V2 Document version: 0.2 13 of 34

 Product Specification
AU OPTRONICS CORPORATION

5.1.2 Signal Electrical Characteristics

Input signals shall be low or High-impedance state when VDD is off.
It is recommended to refer the specifications of THC63LVDF84A (Thine Electronics Inc.) in
detail.

Signal electrical characteristics are as follows;

Parameter Condition Min Max Unit

Differential Input High

Threshold (Vcm=+1.2V) - 100
Vth [mV]

Differential Input Low

-100 -
Vtl Threshold (Vcm=+1.2V) [mV]

Differential Input
Vcm Common Mode Voltage 1.125 1.375 [V]

Note: LVDS Signal Waveform

B133XW01 V2 Document version: 0.2 14 of 34

 Product Specification
AU OPTRONICS CORPORATION

5.2 Backlight Unit

LED Parameter guideline for LED driving selection

Parameter Symbol Min Typ Max Units Condition

LED Forward Voltage VF 3.0 3.2 3.4 [Volt] (Ta=25 )

LED Forward Current IF - 20 30 [mA] (Ta=25 )

LED Power consumption [Watt] (Ta=25 )

PLED - - 3.8 Note 1

(Ta=25 )
LED Life-Time N/A 10000 - - Hour IF=20 mA
Note 2

Output PWM frequency F PWM 100 200 20K Hz

Duty ratio -- 5 -- 100 %

Note 1: Calculator value for reference PLED =IF ×VF × LED(Qty)

Note 2: The LED life-time define as the estimated time to 50% degradation of minimum specification
luminance.

B133XW01 V2 Document version: 0.2 15 of 34

 Product Specification
AU OPTRONICS CORPORATION

6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.

1 2 1365 1366

1st Line R G B R GB R G B R GB

768th Line R G B R GB R G B R GB

B133XW01 V2 Document version: 0.2 16 of 34

 Product Specification
AU OPTRONICS CORPORATION

6.2 The input data format

Signal Name Description

R5 Red Data 5 (MSB) Red-pixel Data
R4 Red Data 4 Each red pixel's brightness data consists of
R3 Red Data 3 these 6 bits pixel data.
R2 Red Data 2
R1 Red Data 1
R0 Red Data 0 (LSB)

Red-pixel Data
G5 Green Data 5 (MSB) Green-pixel Data
G4 Green Data 4 Each green pixel's brightness data consists of
G3 Green Data 3 these 6 bits pixel data.
G2 Green Data 2
G1 Green Data 1
G0 Green Data 0 (LSB)

Green-pixel Data
B5 Blue Data 5 (MSB) Blue-pixel Data
B4 Blue Data 4 Each blue pixel's brightness data consists of
B3 Blue Data 3 these 6 bits pixel data.
B2 Blue Data 2
B1 Blue Data 1
B0 Blue Data 0 (LSB)

Blue-pixel Data
RxCLKIN Data Clock The typical frequency is 72 MHZ.. The signal is
used to strobe the pixel data and DE signals. All
pixel data shall be valid at the falling edge when
the DE signal is high.
This signal is strobed at the falling edge of
DE Display Timing RxCLKIN. When the signal is high, the pixel
data shall be valid to be displayed.
The signal is synchronized to RxCLKIN .
VS Vertical Sync The signal is synchronized to RxCLKIN .
HS Horizontal Sync

Note: Output signals from any system shall be low or High-impedance state when VDD is off.

B133XW01 V2 Document version: 0.2 17 of 34

 Product Specification
AU OPTRONICS CORPORATION

6.3 Integration Interface and Pin Assignment

LVDS is a differential signal technology for LCD interface and high speed data transfer device.

PIN# Signal Name Description

1 NC No Connection (Reserve)

2 AVDD PowerSupply,3.3V(typical)

3 AVDD PowerSupply,3.3V(typical)

4 DVDD DDC 3.3Vpower

5 NC No Connection (Reserve)

6 SCL DDC Clock

7 SDA DDC Data

8 Rin0- -LVDS differential data input(R0-R5,G0)

9 Rin0+ +LVDS differential data input(R0-R5,G0)

10 GND Ground

11 Rin1- -LVDS differential data input(G1-G5,B0-B1)

12 Rin1+ +LVDS differential data input(G1-G5,B0-B1)

13 GND Ground

14 Rin2- -LVDS differential data input(B2-B5,HS,VS,DE)

15 Rin2+ +LVDS differential data input(B2-B5,HS,VS,DE)

16 GND Ground

17 ClkIN- -LVDS differential clock input

18 ClkIN+ +LVDS differential clock input

19 GND Ground–Shield

20 NC No Connection (Reserve)

21 NC No Connection (Reserve)

22 GND Ground–Shield

23 NC No Connection (Reserve)

24 NC No Connection (Reserve)

25 GND Ground–Shield

26 NC No Connection (Reserve)

27 NC No Connection (Reserve)

28 GND Ground–Shield

29 NC No Connection (Reserve)

30 NC No Connection (Reserve)

31 VLED_GND LED Ground

32 VLED_GND LED Ground

33 VLED_GND LED Ground

34 NC No Connection (Reserve)

B133XW01 V2 Document version: 0.2 18 of 34

 Product Specification
AU OPTRONICS CORPORATION

35 PWM System PWM Signal Input

36 LED_EN LED enable pin(+3V Input)

37 NC No Connection (Reserve)

38 VLED LED Power Supply 6V-21V

39 VLED LED Power Supply 6V-21V

40 VLED LED Power Supply 6V-21V

B133XW01 V2 Document version: 0.2 19 of 34

 Product Specification
AU OPTRONICS CORPORATION
Note1: Viewing from rear of the module
Note2: Start from right side
Note3: Input signals shall be low or High-impedance state when VDD is off.

Connector

40 1

VLED NC

B133XW01 V2 Document version: 0.2 20 of 34

 Product Specification
AU OPTRONICS CORPORATION
Internal circuit of LVDS inputs are as following.
The module uses a 100ohm resistor between positive and negative data lines of each receiver input

Signal Input
LVDS Receiver
Pin No.

8 RxIN0-

9 RxIN0+

11 RxIN1-

12 RxIN1+

14 RxIN2-

15 RxIN2+

17 RxCLKIN-

18 RxCLKIN+

B133XW01 V2 Document version: 0.2 21 of 34

 Product Specification
AU OPTRONICS CORPORATION

6.4 Interface Timing

6.4.1 Timing Characteristics
Basically, interface timings should match the 1366x768 /60Hz manufacturing guide line timing.

Parameter Symbol Min. Typ. Max. Unit

Frame Rate - 50 60 - Hz

Clock frequency 1/ TClock - 72 - MHz

Period TV 780 803 -

Vertical
Active TVD 768 - TLine
Section
Blanking TVB 12 35 -

Period TH 1426 1494 -

Horizontal
Active THD - 1366 - TClock
Section
Blanking THB 60 128 -

Note : DE mode only

6.4.2 Timing diagram

TCLOCK Input Timing Definition ( DE Mode)

DOTCLK

Input Invaild Pixel Pixel Pixel Pixel Pixel Invaild Pixel

Data Data 1 2 3 N-1 N Data 1

DE
THB THD

TH

DE
TVB
TVD

TV

B133XW01 V2 Document version: 0.2 22 of 34

 Product Specification
AU OPTRONICS CORPORATION

6.5 Power ON/OFF Sequence

Value
Parameter Typ. Units
Min. Max.
T1 0.5 - 10 (ms)
T2 5 - 50 (ms)
T3 0.5 - 50 (ms)
T4 400 - - (ms)
T5 200 - - (ms)
T6 200 - - (ms)
T7 0 - 10 (ms)
T8 10 --- --- (ms)
T9 10 --- --- (ms)
T10 0 --- --- (ms)
T11 10 --- --- (ms)

B133XW01 V2 Document version: 0.2 23 of 34

 Product Specification
AU OPTRONICS CORPORATION

7. Connector Description

Physical interface is described as for the connector on module.

These connectors are capable of accommodating the following signals and will be following
components.

7.1 TFT LCD Module

Connector Name / Designation For Signal Connector

Manufacturer IPEX or compatible

Type / Part Number IPEX 20455-040E-12 or compatible

Mating Housing/Part Number IPEX 20453-040T-01 or compatible

B133XW01 V2 Document version: 0.2 24 of 34

 Product Specification
AU OPTRONICS CORPORATION

8. LED Driving Specification

8.1 Connector Description

It is a intergrative interface and comibe into LVDS connector. The type and mating refer to
section 7.

8.2 Pin Assignment

PIN# Signal Name Description

31 VLED_GND LED Ground

32 VLED_GND LED Ground

33 VLED_GND LED Ground

34 NC No Connection (Reserve)

35 PWM System PWM Signal Input

36 LED_EN LED enable pin(+3V Input)

37 NC No Connection (Reserve)

38 VLED LED Power Supply 6V-21V

39 VLED LED Power Supply 6V-21V

40 VLED LED Power Supply 6V-21V

B133XW01 V2 Document version: 0.2 25 of 34

 Product Specification
AU OPTRONICS CORPORATION

9. Vibration and Shock Test

9.1 Vibration Test

Test Spec:
Test method: Non-Operation
Acceleration: 1.5 G
Frequency: 10 - 500Hz Random
Sweep: 30 Minutes each Axis (X, Y, Z)

9.2 Shock Test Spec:

Test Spec:
Test method: Non-Operation
Acceleration: 220 G , Half sine wave
Active time: 2 ms
Pulse: X,Y,Z .one time for each side

B133XW01 V2 Document version: 0.2 26 of 34

 Product Specification
AU OPTRONICS CORPORATION

10. Reliability

Items Required Condition Note

Temperature
Humidity Bias Ta= 40 , 90%RH, 300h
High Temperature
Operation
Ta= 50 , Dry, 300h
Low Temperature
Operation
High Temperature Ta= 0 , 300h
Storage
Low Temperature
Storage Ta= 60 , 300h
Thermal Shock
Test Ta= -20 , 300h

Ta=-20 to 60 , Duration at 30 min, 100 cycles

Contact : ±8 KV Note 1
ESD
Air : ±15 KV

Note1: According to EN 61000-4-2 , ESD class B: Some performance degradation allowed. No data lost

. Self-recoverable. No hardware failures.

Remark: MTBF (Excluding the LED): 30,000 hours with a confidence level 90%

B133XW01 V2 Document version: 0.2 27 of 34

 Product Specification
AU OPTRONICS CORPORATION

11. Mechanical Characteristics

11.1 LCM Outline Dimension

Front view

B133XW01 V2 Document version: 0.2 28 of 34

 Product Specification
AU OPTRONICS CORPORATION

Rear view

B133XW01 V2 Document version: 0.2 29 of 34

 Product Specification
AU OPTRONICS CORPORATION

12. Shipping and Package

12.1 Shipping Label Format

Manufactured YY/WW
Model No: B133XW01 V2 C SU Pb
AU Optronics 65 3402 E65 3402 E65 3402 E
MADE IN CHINA (S1)
RoHS

H/W: 0A F/W:1

B133XW01 V2 Document version: 0.2 30 of 34

 Product Specification
AU OPTRONICS CORPORATION

12.2 Carton package

The outside dimension of carton: 437 (L) mm x 359 (W) mm x 285 (H) mm

12.3 Shipping package of palletizing sequence

B133XW01 V2 Document version: 0.2 31 of 34

 Product Specification
AU OPTRONICS CORPORATION

13. Appendix: EDID description

Address FUNCTION Value Value Value Note
HEX HEX BIN DEC
00 Header 00 00000000 0
01 FF 11111111 255
02 FF 11111111 255
03 FF 11111111 255
04 FF 11111111 255
05 FF 11111111 255
06 FF 11111111 255
07 00 00000000 0
08 EISA Manuf. Code LSB 06 00000110 6
09 Compressed ASCII AF 10101111 175
0A 2C 00101100 44
tsrif BSL ,xeh
0B edoC tcudorP 12 00010010 18
0C 32-bit ser # 00 00000000 0
0D 00 00000000 0
0E 00 00000000 0
0F 00 00000000 0
10 Week of manufacture 01 00000001 1
11 Year of manufacture 12 00010010 18
12 EDID Structure Ver. 01 00000001 1
13 EDID revision # 03 00000011 3
14 Video input def. (digital I/P, non-TMDS, CRGB) 80 10000000 128
15
Max H image size (rounded to cm) 1D 00011101 29
Max V image size (rounded to cm)
16 Display Gamma(=(gamma*100)-100) 10 00010000 16
17 Feature support (no DPMS, Active OFF, RGB, tmg Blk#1) 78 01111000 120
Red/green low bits (Lower 2:2:2:2 bits)
18 Blue/white low bits (Lower 2:2:2:2 bits) 0A 00001010 10
19 Red x (Upper 8 bits) F9 10111010 186
1A D5 01100101 101
1B 95 10011011 155
1C Red y/ highER 8 bits 55 01011001 89
1D Green x 54 01010100 84
1E Green y 93 10011110 158
1F Blue x 27 00100110 38
20 Blue y 21 00011010 26
21 White x 50 01001101 77
22 White y 54 01010010 82
23 Established timing 1 00 00000000 0
24 Established timing 2 00 00000000 0
25 Established timing 3 00 00000000 0
26 Standard timing #1 01 00000001 1
27 01 00000001 1
28 Standard timing #2 01 00000001 1
29 01 00000001 1
2A Standard timing #3 01 00000001 1
2B 01 00000001 1
2C Standard timing #4 01 00000001 1
2D 01 00000001 1

B133XW01 V2 Document version: 0.2 32 of 34

 Product Specification
AU OPTRONICS CORPORATION

2E Standard timing #5 01 00000001 1

2F 01 00000001 1
30 Standard timing #6 01 00000001 1
31 01 00000001 1
32 Standard timing #7 01 00000001 1
33 01 00000001 1
34 Standard timing #8 01 00000001 1
35 01 00000001 1
36 Pixel Clock/10000 LSB 20 00100000 32
37
Pixel Clock/10000 USB 1C 00011100 28
Horz active Lower 8bits
38 Horz blanking Lower 8bits 56 01010110 86
39 HorzAct:HorzBlnkUpper 4:4 bits 80 10000000 128
Vertical Active Lower 8bits
3A Vertical Blanking Lower 8bits 50 01010000 80
3B Vert Act : Vertical Blanking(upper 4:4 bit) 00 00000000 0
HorzSync. Offset
3C 23 00100011 35
HorzSync.Width
3D VertSync.Offset : VertSync.Width 30 00110000 48
3E 30 00110000 48
3F 20 00100000 32
40 36 00110110 54
41 Horz&Vert Sync Offset/Width Upper 2bits 00 00000000 0
42 Horizontal Image Size Lower 8bits 25 00100101 37
43 Vertical Image Size Lower 8bits A4 10100100 164
44 Horizontal & Vertical Image Size (upper 4:4 bits) 10 00010000 16
45 Horizontal Border (zero for internal LCD) 00 00000000 0
46 Vertical Border (zero for internal LCD) 00 00000000 0
Signal (non-intr, norm, no stero, sep sync, neg pol)
47 18 00011000 24
48 Detailed timing/monitor 00 00000000 0
49 descriptor #2 00 00000000 0
4A 00 00000000 0
4B 0F 00001111 15
4C 00 00000000 0
4D 00 00000000 0
4E 00 00000000 0
4F 00 00000000 0
50 00 00000000 0
51 00 00000000 0
52 00 00000000 0
53 00 00000000 0
54 00 00000000 0
55 00 00000000 0
56 00 00000000 0
57 00 00000000 0
58 00 00000000 0
59 20 00100000 32
5A Detailed timing/monitor 00 00000000 0
5B descriptor #3 00 00000000 0
5C 00 00000000 0
5D FE 11111110 254
5E 00 00000000 0

B133XW01 V2 Document version: 0.2 33 of 34

 Product Specification
AU OPTRONICS CORPORATION

5F Manufacture 41 01000001 65 A
60 Manufacture 55 01010101 85 U
61 Manufacture 4F 01001111 79 O
62 0A 00001010 10
63 20 00100000 32
64 20 00100000 32
65 20 00100000 32
66 20 00100000 32
67 20 00100000 32
68 20 00100000 32
69 20 00100000 32
6A 20 00100000 32
6B 20 00100000 32
6C Detailed timing/monitor 00 00000000 0
6D descriptor #4 00 00000000 0
6E 00 00000000 0
6F FE 11111110 254
70 00 00000000 0
71 Manufacture P/N 42 01000010 66 B
72 Manufacture P/N 31 00110001 49 1
73 Manufacture P/N 33 00110011 51 3
74 Manufacture P/N 33 00110011 51 3
75 Manufacture P/N 58 01011000 88 X
76 Manufacture P/N 57 01010111 87 W
77 Manufacture P/N 30 00110000 48 0
78 Manufacture P/N 31 00110001 49 1
79 Manufacture P/N 20 00100000 32
7A Manufacture P/N 56 01010110 86 V
7B Manufacture P/N 32 00110010 50 2
7C 20 00100000 32
7D 0A 00001010 10
7E Extension Flag 00 00000000 0
7F Checksum 11 10111000 184

B133XW01 V2 Document version: 0.2 34 of 34