Attendance and Access Control System Using RFID System - 24 Pages
Attendance and Access Control System Using RFID System - 24 Pages
This report is submitted in partial fulfillment of the requirements for the award of
Bachelor of Electronic Engineering (Industrial Electronics) With Honours
May 2011
UNIVERSTI TEKNIKAL MALAYSIA MELAKA
FAKULTI KEJURUTERAAN ELEKTRONIK DAN KEJURUTERAAN KOMPUTER
TIDAK TERHAD
Disahkan oleh:
__________________________ ___________________________________
(TANDATANGAN PENULIS) (COP DAN TANDATANGAN PENYELIA)
“I hereby declare that this report is the result of my own work except for quotes as
cited in the references.”
Signature :…………………………………………..
Author : Nor Amiyana Binti Mohd Alias
Date :…………………………………………..
iv
“I hereby declare that I have read this report and in my opinion this report is
sufficient in terms of the scope and quality for the award of Bachelor of Electronic
Engineering (Industrial Electronics) With Honours”
Signature :………………………………………
Supervisor’s Nam e : Puan Azdiana binti Md. Yusop
Date :………………………………………
v
ACKNOWLEDGEMENT
The highest of gratitude to Allah S.W.T, The creator of all for His blessing
and mercy has allowed me to live and serve in this world of His. This feat thus far
can only be accomplished only if He allows it.
Thank you also to my supervisor and teacher Puan Azdiana binti Md Yusop
for guiding me towards the journey of completion. Your knowledge on the various
things has greatly increased my confidence in doing this project.
I would also like to thank my family and friends for supporting me towards
the end. All of your support has motivated me in many instances. All of the
experience has been educating, humbling and very nostalgic.
ABSTRACT
This system can completely control the access to the area with automatic
identification process and automatic attendance record system, with each vehicle is
equipped with an active sticker/ tags which is previously registered on the system.
The active sticker will send microwave signal constantly to the reader.
When the reader installed near the gateway has receives the signal from the
active sticker/tags, it will transmit the signal to the gateway controller (PIC
16F876A).
Then the RFID system will verify the validity of the sticker. If valid, the time
of arrival is recorded as part of the attendance and the relay on the controller will
drive the gate open and permit the vehicle’s access.
If the sticker is not valid, microcontroller will not function and the gate will
remain closed. A camera will then take the picture of the affected vehicle. The
images are saved in the database.
ABSTRAK
Pembaca RFID akan mengesahkan kesahihan kad tersebut. Jika sah, waktu
kedatangan direkodkan sebagai sebahagian daripada kehadiran dan geganti pada
pengawal akan mendorong pintu terbuka dan membolehkan kenderaan masuk.
Jika kad tersebut tidak sah, pengawal tidak akan berfungsi dan pintu tidak
akan terbuka.. Sebuah kamera akan mengambil gambar kenderaan yang tersebut.
Gambar akan disimpan di dalam pangkalan data..
ix
TABLE OF CONTENTS
PROJECT TITLE i
APPROVAL FORM ii
PAGE OF ADMISSION iii
SUPERVISOR CONFIRMATION iv
DEDICATION v
ACKNOWLEDGEMENT vi
ABSTRACT vii
ABSTRAK viii
TABLE OF CONTENTS ix
LIST OF FIGURES xiii
LIST OF TABLE xv
LIST OF APPENDICES xvi
LIST OF ABBREVIATIONS xvii
1 INTRODUCTION
2 LITERATURE REVIEW
x
2.1 Introduction 8
2.2 Attendance And Access Control System
Using RFID System Concept 9
2.3 Identification System 10
2.3.1 Automated fingerprint identification 11
2.3.2 Barcode system 12
2.3.3 Radio Frequency Based Identification(RFID) 12
2.3.3.1 RFID Reader 12
2.3.3.2 RFID Tag 14
2.4 Existing Attendance System 14
2.4.1 RFID Based Attendance System
(AT89S52 + RFID) 15
2.4.2 Time Attendance System by Tutis
Technologies Limited 15
2.4.3 Smart Clock 16
2.4.4 Automation of Time and Attendance
using RFID Systems 17
3.1 Introduction 19
3.2 Chosen Components 19
3.2.1 Hardware overview 20
3.2.1.1 Microcontroller 22
3.2.1.1.1 PIC16F876A by
Microchip 23
3.2.1.2 PIC programmer 26
3.2.1.2.1 UIC00BUSB ICSP
PIC Programmer 26
3.2.1.3 Power Supply 27
3.2.1.3.1 Voltage Regulator 28
3.2.1.4 RFID 29
3.2.1.4.1 IDR-232 RFID Reader 29
xi
3.2.1.4.1.1 RFID-IDR
232N setup 30
4 METHODOLOGY
5.1 Introduction 52
5.2 Attendance And Access Control System Using
RFID System Test Result 51
5.3 Test On System 51
5.4 The Database for Attendance and access control
system using RFID system 5
5.4.1 First step 56
5.4.2 Second Step 56
5.4.3 Third step 57
6.1 Conclusion 58
6.2 Problems 58
6.3 Recommendations 59
6.3.1 Hardware Improvement 59
6.3.2 Software Improvement 59
REFERENCES 60
APPENDIX A 61
APPENDIX B 68
APPENDIX C 70
xiii
LIST OF FIGURES
LIST OF TABLES
LIST OF APPENDICES
NO TITLES PAGE
A Code of program 61
B Schematic 68
C PIC16F876A datasheet 70
xvii
LIST OF ABBREVIATIONS
INTRODUCTION
Attendance is define as the act of being present (at a meeting or event etc.),
the frequency with which a person is present or the number of people that are
present. Attendance is one of the important factors that affect the staff performance
in work.
Attendance and access control systems are used by companies of all sizes to
record working hours of employees in order to pay their wages. Some companies
have a requirement to record the number of hours spent on specific tasks in order to
evaluate the jobs accurately. This is referred to as job costing.
The suitable solution for this problem is by design a system that will record
attendance automatically. In this project, Radio Frequency Identification (RFID)
system used to record student attendance automatically
2
RFID technology differs from bar codes. RFID can read the tag using RF,
meaning that the RFID reader can be read from a distance, right through your
clothes, wallet, backpack or purse. Besides the RFID tag consist of unique
identification (ID) for each tag.
The technology used in RFID has been around since the early 1920s. In our
country, this technology already been used for several years in certain places. Some
places, they prefer to used Barcode which is cheaper than RFID. Technology spread
very fast. In few years later, there is not impossible if RFID will replace the barcode
system in today’s life.
This project will used ID card as RFID tag. The identification number on the
card will indicate the information of user. Each ID number has pre assigned in the
database. The data in this context consists of the name, department, the ID number
and car plat number. This project is developed to track the number of attendance of
people in the desired workplace. This method is more effective to prevent problem in
process getting attendance manually.
3
1.1.1 Design the attendance and access control system using the RFID
system with extensive supervision.
Currently the method that companies use to control the flow of people
coming in and out is very lacking. People (employees or outsiders) can go in and out
of the company’s premises with minimal supervision. Important records such as
picture and time of entry or exit are not properly managed or recorded. The
attendance system also has the absolute potential of wasting valuable time since the
employees need to line up and wait their turn to tally up hand-written time cards or
punch clock cards manually.
The project is created in based on the scope. The scope is important to ensure
the manufacturing of the project according as planned. However, this scope can be
changed to obtain better results. Among the initial scope set is:
1.4.1 This system can be used in big companies, industries, colleges,
schools, etc where there are many numbers of candidates available.
1.4.2 Total width of the passage should be 4~6m, one entrance and one
exit. Example like UTeM.
1.4.3 There’s no need to stop if necessary. The passing speed should
be under 60 km/h.
1.4.4 The identifying process is full automatic, which can avoid the
problem that driver must open the window to punch the card in
bad weathers.
4
1.5 Methodology
This project began with the research of the proposed title. The result of that
research is then discussed with the supervisor. Once we have agreed with the
supervisor on the title, the background study of this project is searched. Here,
theories on this project are found. When the project has progressed thus far, the
process of designing the system can be done. Components can now be chosen and
the control elements programmed using the desired software. An interface device
should also be chosen. The correct software is chosen to comply with the control
elements. The flowchart of the system shown below in figure 1.1
5
Start
Input : Reader
has received the signal
from the active sticker
NO
Card =valid
YES
END
Figure 1.1: Flow chart of Attendance And Access Control System Using RFID
System
6
This report shall explain how this project came to be. What is done thus far is
compiled in this report. All of contents of this report are useful to fast pacing this
project to the next level. So it is important that the contents of this report to be
thoroughly researched and put into place.
Chapter 1 introduces the project as a whole. The early and basic explanations
are mentioned in this chapter. This chapter consists of the project’s objectives,
statements of problems, scope of work, and the simplified methodology.
Chapter 4 explains how this project came to be. It is the methodology. The
ways and procedures in which this project is done. This chapter will enlighten the
part most important of all, the flow this project. What is researched and what needs
to be done is explained in this chapter.
Chapter 5 concentrates on the result and discussion of this project. What has
been done thus far is explained in diagrams and written programs. Why the results
are like so will also be explained. The reasons and setbacks that cause the project to
be halted are discussed in this chapter. The expected results will also be mentioned in
this chapter.
throughout this project. After the project is done, recommendations are made for the
betterment of this project or any expansions or upgrades that might be done in the
future.