Scribd
Upload
72 views13 pages

Infrastructure Management Pack For Vrealize Operations Manager

The document provides instructions for installing and configuring the Eaton Infrastructure Management Pack for VMware vRealize Operations Manager. It describes prerequisites including licenses for vRealize Operations Manager and Eaton IPM. It then provides step-by-step instructions for connecting to vRealize Operations Manager, installing the management pack, configuring solutions, and checking discovered UPS systems and data. Dashboards and known issues are also outlined.

Uploaded by

duc pham
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
72 views13 pages

Infrastructure Management Pack For Vrealize Operations Manager

The document provides instructions for installing and configuring the Eaton Infrastructure Management Pack for VMware vRealize Operations Manager. It describes prerequisites including licenses for vRealize Operations Manager and Eaton IPM. It then provides step-by-step instructions for connecting to vRealize Operations Manager, installing the management pack, configuring solutions, and checking discovered UPS systems and data. Dashboards and known issues are also outlined.

Uploaded by

duc pham
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 13

Infrastructure Management Pack for vRealize Operations

Manager
Purpose of the article
The following article describes how to use Eaton Infrastructure Management Pack (MP) for vRealize Operations Manager 1.0

Pre-requisite
VMware vRealize Operations Manager server running with
Licenses
IPM running with
UPSes
vCenter connector configured
Policy defined
Gold or Silver license
Eaton MP downloaded (.pak)
Step by step guide
Connect on VMware vRealize Operations Manager
Use the Web interface

The way to go in the different section is through the "Tab"


Install the management pack (MPs)
1. Go to "Administration" => "Solutions"
2. Click on "Add" (green cross)
3. Browse and select the MP
4. Upload

Configure the solutions


1. Select the solution
2. Click on "configure"
3. Add a new instance
4. Configure as your needs
5. Do for both VMware and Eaton

Once the solutions installed and configured, the discovery process will start (if checked) and the monitoring part will start every 5 minutes (default
value)
Configure the content
After the installation of the MP, you can modify all the symptoms, alarms, icons, dashboard, actions, recommendations in the content panel.

You can easily access the IPMAdapter alert with the filter on "Adapter Type" on "IPM"

You can modify the name and the configuration regarding your needs.
Check the UPS discovered and the data
1. Select "Environment"

2. Go in "UPS Systems"
3. Select a UPS to see the summary

4. You will see different tabs


a. Alerts is the list of the alerts
b. Analysis will show the data computed

i.
4.

b.

i. Workload

ii. Anomalies
iii. Faults
iv. Capacity Remaining
v. Time Remaining
vi. Stress
c. Troubleshooting
i. Symptoms

ii. All metrics

d. Details with configuration Views and Heatmaps


e. Environment with the Map
f. Project

g. Reports

All this area is for analysis and troubleshooting.

Dashboard
Home Page with the "Recommendations" dashboard with the UPS alarms and with the UPS in the grid of the Health Weather Map.

When you clic on the square you can see the relationship between the square highlighted.
Eaton Dashboards
You can clic on "Dashboard Lists" and select UPS Overview to see the Eaton Dashboard.

Known issues
1) When two network interfaces are installed in the same UPS, you can't control the one exposed into this management pack.
2) This management pack handles the protection of servers discovered through vCenter. The protection of a standalone ESXi is not reported into
this Management Pack.
3) Virtual Power Sources are not available into this management pack.

Troubleshooting
You need to go in "Configuration" => "Support" => "Logs"

Expand the Master => Expand "Collector" and double clic on the IPMAdapter logs.

For customer, generating a support bundle will be the preferred method.

You might also like