FS Series

DIN size W48×H48mm 8Pin plug Counter

▣Features
lAvailable to count from low speed to high speed
: selectable 1cps, 30cps, 2kcps, 5kcps
lWide range of input power
: 100-240VAC 50/60Hz, 12-24VDC(Option)
lMemory retention function when the power fails
lCount Up, Count Down function
lAvailable to set decimal point
lMicroprocessor built-in

Please read "Caution for your safety" in operation

! manual before using.

▣Specifications
※A blacked( ) item is upgraded function.
Single preset FS4A
Model
Indication type FS5B
Digit 4 5
Digit size W4×H8mm
Power supply 100-240VAC 50/60Hz, 12-24VDC(Option)
Allowable voltage range 90 ~ 110% of rated voltage
Power consumption 4VA
Max. counting speed for
Selectable 1cps/30cps/2kcps/5kcps by internal DIP switch
CP1, CP2

Min. input Approx.20ms

signal width RESET input

COUNT IN No-voltage input

U Impedance at short-circuit : Max. 470kΩ
Input U Residual voltage at short-circuit : Max. 1VDC
RESET
U Impedance at open-circuit : Min. 100kΩ
One-shot output time 0.05 ~ 5sec
Control Type SPST(1a)
Contact
output Capacity 250VAC 3A resistive load
Memory retention 10 years(When using non-voltage semiconductor memory)
External sensor power 12VDC ±10% 50mA max.
Insulation resistance 100MΩ(at 500VDC)
Dielectric strength 2000VAC 50/60Hz for 1 minute
Noise AC power ±2kV the square wave noise(pulse width:1㎲) by the noise simulator
strength DC power ±500V the square wave noise(pulse width:1㎲) by the noise simulator
Mechanical 0.75mm amplitude at frequency of 10 ~ 55Hz in each of X, Y, Z directions for 1 hour
Vibration
Malfunction 0.5mm amplitude at frequency of 10 ~ 55Hz in each of X, Y, Z directions for 10 minutes
Mechanical 300m/s²(Approx. 30G) in X, Y, Z directions 3 times
Shock
Malfunction 100m/s²(Approx. 10G) in X, Y, Z directions 3 times
Mechanical Min. 10,000,000 times
Relay
Min. 100,000 times
life cycle Electrical
(250VAC 3A at resistive load)
Ambient temperature -10 ~ +55℃(at non-freezing status)
Storage temperature -25 ~ +65℃(at non-freezing status)
Ambient humidity 35 ~ 85%RH
AC power Approx. 122g Approx. 112g
Weight
DC power Approx. 130g Approx. 120g

A-53
 8 Pin Plug Counter
▣Connections
(A)
Counter

(B)
Timer

(C)
Temp.
controlle

(D)
Power
controlle

▣Dimensions
lBracket lPannel cut-out (E)
Panel
Min.55 meter

(F)
Tacho/
Speed/
Pulse
M in.62 meter

(G)
Unit:mm Display
unit

lSocket (Accessory)

(H)
Unit:mm Unit:mm Sensor
controlle

(I)
Proximit
sensor

(J)
▣Input connections Photo
electric
sensor
◎Input logic : No-voltage input(NPN)
lSolid-state input(Standard input sensor :NPN output type sensor) lContact input
Sensor Counter Counter (K)
Brown Pressur
sensor

Black
Inner Inner Inner
circuit circuit circuit (L)
Rotary
Blue
encoder

(NP N output) (NPN open Counting speed:

collector output) (M)
1 or 30cps s etting
input 5-Phase
stepping
mot or &
◎PNP output type sensor Dr iver &
Controlle
S ensor Counter
U PNP oupput type sensor cannot be used directly.
Brown
U RL : Resistive load of proximity switch
(Built in the sensor)
Black
Inner R1 : 1 Resister to be connected at out side
circuit U Please set R1 value to make the compo sed
Blue resistance of RL+R1 is max. 470
(Be sure that RL value will be different by sensors)

A-54
FS Series
◎Input & output connections
Br own

Black

Blue

lPlease select proper capacity of load

Load not to exceed contact capacity.
Contact capacity : 250VAC 3A Max.
Contact type : 1a

lTotal value of load capacity and current

consumptionshould not be exceed
current cap acity(12VDC 50mA max.)

▣ Selection by DIP switches

Output operation mode selection
Memory retention selection
Max. counting speed
NC (Non using)
Up/Down mode selection

※There is no output operation mode DIP SW numbers are changed from 7 to 8

SW(No. 6, 7, 8) in FS5B.
lMax. counting speed lUp/Down mode
Function Function

Down mode

Up mode

lMemory retention
Function
Power reset
(Non memory)

Memory

▣ Decimal point setting

Dispaly the decimal point.

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
RESET RESET RESET RESET

0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3
+ + + + TIM E
+ + + + TIME
+ + + + TIME
+ + + + TIME

FS4A FS4A FS4 A FS4A

RUN mode Return to RUN mode

※It returns to decim al point ※ When "dp" is flickering, ※If pressing one of digital ※It returns to RUN mode
setting status if pres sing one touch the Reset switch buttons( + , - )in if pressing RESET button
RES ET button for over button. decimal point setting mode, for over 3sec. in decimal
3sec. in RUN mode. decimal point will be m oved point setting status.
to Up(+)direction.
lChanging the decimal point
※ It returns to RUN mode if no RESET button or digital
+ + + + switch is applied for 60s ec. in decimal point setting
status.
- (Factory default) - - -
※ The decimal point setting is existed in indic ation type.

A-55
 8 Pin Plug Counter
▣Counting operation of indication mode(Indication model)
lUp input mode lDown intput mode (A)
Counter

+Max.display value +Max.display value

(B)
Timer

-Max.display value

▣Output operation mode (C)

Temp.
controlle
One-shot output(0.05 ~ 5sec) Self-holding output

Output mode
Up mode Down mode Operation after count up (D)
(SW1) Power
controlle

Reset Reset The display value continues

Pr eset Pr eset until reset signal is applied
8
then output is held (E)
Panel
U Self-holding output is held meter
Output until reset signal is applied.
Output

(F)
Reset Reset Tacho/
Preset Pr eset The display value and Self- Speed/
8 holding output are held until Pulse
meter
reset signal is applied.
Output Output
(G)
Display
Reset Reset unit

Preset Pr eset The display value returns to

8 reset start status when display
value is reached to preset value. (H)
Sensor
Output Output controlle

Reset Reset
Preset Pr eset The display value is held until (I)
8 output is OFF then returns to Proximit
reset start status. sensor

Output Output
(J)
Reset Reset Photo
electri c
Pr eset
8 Preset The display value continues sensor

until reset signal is applied.

Output Output (K)

Pressur
sensor
Reset Reset
The display value is held during
Preset Pr eset
8 one-shot output time, counting
process is returned to reset start (L)
status as soon as output is ON. Rotary
encoder
Output Output

Reset Reset (M)

P reset Pr eset 5-Phase
The display value continues
8 stepping
during one-shot output time. motor &
Driver &
Controlle
Output Output

U Up input mode
Reset Reset
-Output is ON when
Preset Pr eset
8 (Display value) ≥ (Preset value)
U Down input mode
-Output is ON when
Output Output (Display value) ≤ (Zero)

A-56
FS Series
▣Proper usage
◎Reset function ◎Error display
lReset Error signal Error description Returning method
In case of changing the input mode after supplying Change the set value
Zero set state
the power, please take a external reset or manual to non zero state
reset. If reset is not executed, the counter will ※When Error is displayed, the output continues OFF state.
be working as previous mode. ※There is no Error function in the indication type.

lReset signal width

It is reset perfectly when the reset signal is applied
during min. 20ms regardless of the contact input
_ _ _
& solid-state input. _
RESET

* 0 0 0 0
+ + + +
TI ME

Reset input FX4S

** ◎Detach the case from body

*In case of a contact reset, it is reset perfectly if While pushing the lock eguipment with with driver
the ON time of reset signal is applied during min. to the way of front, push the terminal block.
20ms even though a chattering is occurred.
**It can be input the signal of CP1&CP2 after min.
50ms from closing time of reset signal.
◎Sensor power
P ush the terminal block
The power 12VDC which is provided to sensor is to front part
built in it. Please use it under Max. 50mADC.
◎Min. signal width of CP1, CP2 input
*T
1 1

** ** ◎Power
*Please make duty ratio(ON/OFF) 1:1. The inner circuit voltage starts to rise up for the first
** Min. signal width 1cps : Max. 0.5sec 100ms after power on, the input may not work at this
30cps : Max.16.7ms time. And also the inner circuit voltage drops down
2kcps : Max. 0.25ms for the last 500ms after power off, the input may not
5kcps : Max.0.1ms work at this time.
◎Max. counting speed ON
P ower
This is respond speed per 1sec. when the duty ratio OFF
100ms 500ms
(ON/OFF) of input signal is 1:1. The unstable time
against the input signal.
If duty ratio is not 1:1, the respond speed will be
getting slow against input signal and also the width
between ON and OFF should be over min. signal
width and also one of ON width and OFF width is
Under min. signal width, this product may not
response.
Ta Tb Width of Ta(ON) and Tb(OFF)
must be larger than Min. signal
width.
Max.counting speed is 1/2 value
3×Ta of catalog spec. when duty rate
is 1:3.
It can not respond because Max.
signal width(1a) is little.

A-57