Put data in blue ones

width 0.6 m

depth 4m

a 0.06 m

Compressive strength Fc 4000 Psi 27579

Yielding Fy 60,000 Psi 413685.4

As 0.002039998 m2

M 432.9296262 kN m/m
spacing 0.139215828 5.479534975 inches c/c

Unit wt of soil ɣs 18 kN/m3

Unit wt of water ɣw 9.8 kN/m3
Unit wt of concrete ɣc 24 kN/m3

Applied
Pw 78.4 kN/m

Mw 167.2533333 kN m/m Areq 0.000788

Asmin 0.0036 m /m 2
Mu 763.9942
As use 0.0036 m2/m
Spacing 0.078888889 m c/c 3.1050667 in c/c

For soil

Width 0.3 m
Depth 3m
a 0.03 m
ø 32 degree
Ka 0.470080736
Ps 38.0765396
Mapplied 60.92246336 Areq 0.000574
As min 0.00135 M 143.2489
As used 0.00135
spacing 0.286666667 11.2832

200/fy 0.003333333
 U.S. rebar size chart
Linear Mass
Imperial "Soft" Density Nominal diameter
metric
bar size size lb⁄ft (kg/m) (in) (mm)

0.250
#2 #6 0.167 0.249 = 1⁄4 6.35
0.375
#3 #10 0.376 0.561 = 3⁄8 9.525
0.500
KN/m2 #4 #13 0.668 0.996 = 4⁄8 12.7
0.625
KN/m2 #5 #16 1.043 1.556 = 5⁄8 15.875
0.750
#6 #19 1.502 2.24 = 6⁄8 19.05
0.875
#7 #22 2.044 3.049 = 7⁄8 22.225
#8 #25 2.67 3.982 1 25.4
#9 #29 3.4 5.071 1.128 28.65
#10 #32 4.303 6.418 1.27 32.26
#11 #36 5.313 7.924 1.41 35.81
#14 #43 7.65 11.41 1.693 43
#18 #57 13.6 20.284 2.257 57.3
#18J 14.6 21.775 2.337 59.4

m2/m spacing 0.645848 25.42059 inches c/c

kN m/m
rt

Nominal area

(in²) (mm²) m2

0.05 32 0.000032

0.11 71 0.000071

0.2 129 0.000129

0.31 200 0.0002

0.44 284 0.000284

0.6 387 0.000387

0.79 509 0.000509
1 645 0.000645
1.27 819 0.000819
1.56 1006 0.001006
2.25 1452 0.001452
4 2581 0.002581
4.29 2678 0.002678
 Put values in Blue cells
T1 0.3 m 12 inches
T2 0.3 m 12 inches
T3 0.3 m 12 inches
L1 0.7 m 2.30 f
L2 0.3 m 1.0 f
H1 2.2 m 7.2 f
L=L1+L2+T2 1.3 m 4.3 f
H=h1+T3 2.5 m 8.2 f
Ht of overburden 0.75 m
Allowable pressure of soil 107.251 KN/m2 1.000 ton/f2
Compressive strength Fc 3000 Psi 20682
Yielding Fy 60,000 Psi 413640
Angle of internal friction ø 35 degrees
Unit wt of soil ɣs 19 kN/m3 120.954
Unit wt of water ɣw 9.8 kN/m 3
62.3868
Unit wt of concrete ɣc 24 kN/m3 152.784
Ka 0.27099
Ko 0.426424
Psur 13.36838 KN/m
Pw 30.625 KN/m
Ps 25.3189 KN/m
Ms applied 31.64862 KN m/m
Mw 38.28125 KN m/m
Msurcharge 14.70522 KN m/m
Asmin 0.000229 m2/m 0.3554903798 in2/m
Asmin 0.000319 m2/m 0.4943807833 in2/m
Asmin 0.00099 m2/m
Asused 0.00099 m2/m
Mapplied 46.35384 KN m/m use Map for designing
MR capacity 105.0377 KN m/m Ok
Area of bars 0.79 in2 0.0005099375 m2
Spacing 0.515088 m C/C 20.2738769812 inches c/c

Heel design
Wfound 51.98838 KN /m
Mfound 43.93018 KN m/m
Vu 67.58489 KN Shear design is not required
ɸVc 695.8052 Spacing
Vs 320.1574
spacing 7.114608
spacing 0.15
spacing 0.6
Spacing needed 0.1
Default values

0.25
0.25 T1
0.5
0.43

KN/m2 20682000 N/m2 H1

KN/m 2

lb/f3
lb/f3
lb/f3

L2 T2 L1

F.O.S against sliding

Wfill 29.26 KN /m
Wstem 15.84 KN /m stabilizing
Wheel 9.36 KN /m
Pfill 25.3189 KN /m
Psur 13.36838 KN /m Destabilizing

Fresistance 38.1333 sum of stabil

0.1 m Bar area 0.000129
Fsliding 38.68728 sum of destabil

F.O.S slid 0.985681 Not safe against sliding

F.O.S against Overturning

Movr 33.27241
Mres 37.6826

F.O.S over 1.132548 Not safe against overturn

Sizes (Stability checks)

a= 0.490527 m Resultant lies with in m

qmax 102.5866 KN/sqm Not need to increase L

qmin 15.59887 KN/sqm

Allowable pressure should be more than qmax

If a=l/3
qmax 118.1855
qmin 0

if a<l/3
qmax 104.4054
qmin 0
T3
 Not safe against sliding

Not safe against overturning

Resultant lies with in middle third

Not need to increase L

e more than qmax

 Put values in blue cells including yellow

Arm subjected to earth pressure

Mapplied 31.7 KN m/m 7 kip f/f
Asmin 0.347 in2/f using 0.2 in2/f using # 4
a 0.39 inches
фMn 10.6 kip f/f Design ok
spacing 11.8 inches c/c Max spacing 35 or 18"

Opposite Arm
Asmin 0.21 in2/f
Spacing 11.1 inches

Distribution bars in arm B.S

Asmin 0.35 in2/f
Spacing 6.6 inches

Design of Heel (double mesh B.W)

Mapplied 10 kip f/f Using # 4
Asmin 0.2 in2/f
a 0.39 inches
фMn 10.2 kip f/f Deisgn ok
Spacing 11.8 inches c/c Max spacing 35 or 18"

Development Length Check of arm

reinforcement in heel slab

Heel depth 12 inches

ldh 11.0 inches Development length ok
or ldh 4 inches
or ldh 6 inches
max ldh 11.0 inches
bars

bars
U have to put data only in pink cells

Wall thickness 0.75 feet

Wall height 37 feet
width of slab 16.75 feet
Length of slab 18 feet
Thickness of slab 0.5 feet
Thickness of mud 0.25 feet
Thickness of tiles 0.25 feet
Unit wt of conc 150 lb/cf 0.15 kip/cf
Unit wt of soil 120 lb/cf 0.12 kip/cf
Unit wt of mud 125 lb/cf
Unit wt of tiles 130 lb/cf
Unit wt of brick 132 lb/cf
Bearing capacity of soil 2 ton/sf 4.4092 Kips/sf
Ø of soil 30 degrees
Modulus of rupture of conc(1:2:4) 527 KN/sm 10.9634068 kip/sf
Modulus of rupture of conc(1:3:6) 352 KN/sm

Loads of slab 1256.25 lb/f

Loads of mud 523.4375 lb/f D
Loads of tiles 544.375 lb/f
Load of wall 3663 lb/f
steel 1% of conc volume 738.675
Total load 6725.738 lb/f
Total load; 50% for longer walls 3362.869 lb/f
Total Dead load from both sides on longer walls 6725.738 lb/f 6.7257375 kip/f 4.0826

Live load 120 lb/sf 0.12 kip/f

Wu 8.262885 kip/f
Width of footing (1) 1.87401 f
Width of footing (2) 2.5 f
Depth (1) 4.082593 f
Depth (2) 3f Minimum

Thickness of concrete pad 0.549209 feet 6.59050985 inches

 Thickness

6.59050985 inches

B 2.5
Isolated footing Column

Column location Interior

fy 40 ksi 40000
fc 3 ksi 3000
ɣs 120 lb/cf
ɣc 150 lb/cf
D.L 67 kips
L.L 0 kips
Wu 80.4 kips
bottom of footing below final grade 4f
qa 2204 psf
Width of column/wall 12 inches
Assume thickness of footing 12 inches
d 8.5 inches
qe 1694 psf 1.694
Area required 39.55135773 sq-f
L and W of footing 6.28898702 f
Bearing pressure for strength design 2.0328 ksf
depth required for two way or puching shear 20.5 inches
Vu2 76.9273 kips
b0 82 inches 1/b0
least d 1 5.709324864 inches OK
ἀ 40
least d 2 3.715592372 inches OK
depth required for one way or puching shear
Vu1 24.75236118 kips
d 3.992112788 inches OK
Mu 44.70235115 k-f
Mu/φbd2 109.312369 psi
ρ1 0.005
ρ2 0.004107919
ρ from chart 0.0002
As 3.20738338 sq-in

Isolated footing Wall

fy 40 ksi 40000
fc 3 ksi 3000
D.L 4.2 k/f
L.L 0.12 k/f
Width of wall 9 inches
Bottom of the footing 3f
ɣs 100 lb/cf
ɣc 150 lb/cf
qa 4 ksf 4000
assume thickness of pad 20 inches 1.666667
d 16.5 inches
qe 3616.666667 psf 3.616667
Width of footing required 1.194470046 f (say) 2.5
Bearing Pressure for Strength Design 2.0928 ksf
Depth Required for Shear at a Distance d from Face of Wall (Vu) -1.0464 kips
d -1.0613646 inches
h 2.4386354 OK
Determine Steel Area
Cantilever length 0.875 f
Mu 0.80115 k-f
Mu/ɸbd2 4.359555147 psi
From Appendix A, Table A.12, ρ (by interpolation). 0.00345
ρ1 0.005
ρ2 0.004107919
As 0.7425 sq-in
Longitudinal Temperature and Shrinkage Steel 0.324 sq-in

Combined footing
fy 60 ksi 60000
fc 3 ksi 3000
C1 C2
W 12 inches 12
H 12 inches 12
D.L 24.7 kips 24.7
L.L 4.25 kips 4.25
ɣs 100 lb/cf
ɣc 150 lb/cf
Bottom of the footing below ground level 4f
Bearing capacity of soil 2000 psf
C1 acting at distance from lef side X1 6 inches
C2 acting at distance from lef side X2 168 inches
Assume depth of pad 18 inches
Resultant acting on 87 inches 7.25
qe 1525 psf
Area required 37.96721311 sq-in
Bearing Pressure for Strength Design 1.91955095
Soil pressure 13.91674439 f
Effective depth d 14.5 inches
Max shear from diagram 91 kips
Vu 74.18393387 kips
Checking for depth 10.37859872 inches Depth OK

Checking for 2 way shear usually not critical in combined footing

Pu ( for one column C1) 36.44 kips
Pu ( for one column C1) 36.44 kips
bo 106 8.833333
Vu2 252.5548713 kips
Maximum moment from bending moment diagram 306 kip-f
MU/ɸbd2 144.7424436 psi
ᵨ 0.0055
As flex 6.93825 sq-in
As shrink 2.2707 sq-in
Asmin 4.205 sq-in
Asmin 3.454760031 sq-in
http://bendingmomentdiagram.com/solve/

psi
psi Interior
edge
corner

In applying the equation, αs is to be used as 40 for interior

columns (where the perimeter is four-sided), 30 for edge columns (where the perimeter is
three-sided), and 20 for corner columns (where the perimeter is two-sided).

ksf

0.012195 inches

16 " column
9' x 9' footing

over the entire width

0.75

psi
psi
psf
f

ksf
f

psi
psi

inches
inches
kips
kips

f
Depth OK
e the perimeter is
 Jabori-HPP-Type-IV Residential building

fc 3 ksi
fy 40 ksi
Lb 18.25 f Lb>La
La 12.83 f
m 0.70
hmin 4.14 5 inches providing 5 " slab
Effective depth 3.5 inches
Tile thickness 0.33 inches
Mud thickness 3 inches
D.L slab 0.10 ksf
F.D.L 0.12 ksf
L.L 0.04 ksf
F.L.L 0.06 ksf
Wu 0.18 ksf
Coefficient method Case-8
Ca neg 0.081
Cb neg 0.019
Ca pos DL 0.046
Cb pos DL 0.011
Ca pos LL 0.057
Cb pos LL 0.014

Ma neg 2.386664441 kip-f

Mb neg 1.132745563 kip-f
Ma pos 1.47 kip-f
Mb pos 0.72 kip-f

#3 bar @ 6" c/c 6 inches spacing

Ab 0.11 sq-in
As 0.22 sq-in
a 0.29 inches
Mn 2.22 kip-f
 Shell steel from Sap2000

As (sap) 0.018 in2/in

Abar 0.2 in2
Spacing 11.1 inches
fy 40 ksi 40000 psi
fc 3 ksi 3000 psi
Clear width of slab(ln) 10 f
suppose t 5 inches
l 10.41667 f
formula from table (60 grade) 0.05 f 6.25 inches (l/20)
Thickness of slab (40 grade) 5.00 inches 5 inches
Using slab thickness 5.00
d 4.00
Dead Loads
slab 0.0625 ksf
mud 0.03 ksf
tiles 0.02 ksf
T.D.Load 0.1125 ksf
T.Live load 0.04 ksf
Wu 0.199 ksf
Coefficent for Mpos 0.090909 (1/11) From ACI codes
Coefficent for Mneg 0.111111 (1/9)
Mpos 1.809091 kip-f/f 21.70909 kip-in/f
Mneg 2.211111 kip-f/f 26.53333 kip-in/f
Asmin 0.12 sq-in/f using area of steel 0.11 sq-in
a 0.156863 inch
Mn 16.94118 kip-in
spacing 11 inch c/c
spacing 3hf 15 inch
spacing 18 inch

use same area for distribution

bars
spacing 5hf 25 inches
spacing 18 inches
 40
60

0 0
1.809091 10
0 10
-2.21111 10
 U have to put data in pink cells only

Simply supported beam

fy 40 ksi 40000 psi Max
fc 3 ksi 3000 psi
L 15 f C/C of supports
Depth 12 inches
B 12 inches
Dead W slab 1.946 K/f
W beam 0.15 K/f
T.D.L 2.096 K/f
Live Load from slab 0 K/f
Wu 2.126 K/f
Mapplied 59.79375 Kip-f
Assume bar dia (#) 6
Clear cover 1.5 inches
d 10.125 inches
Assume Numbers of bar 6 bmin 12 inches
As 2.649375 sq-in
a 3.4632352941 inches
Mu 66.711652114 K/f*f
Asmin-1 0.6075 sq-inch
Asmin-2 0.4991121805 sq-inch

Shear design
V 15.945 Kips
Vx 14.1511875 Kips
Vc 0 Kips
Vx 14.1511875 Kips
V 15.945 Kips
ɸVc 11.8308072421 Kips 2 legged # 3 bar @ 6 inches c/c
Vs 11.1375 Kips
Spacing 5.0625 inches

15.945 0
14.1511875 0.84375
0 10.375
-14.1511875 14.15625
-15.945 15
 0 0
10.375 59.79375
15 0

T-beam
C/C distance between beam 5
f
Span of beam 50 f
bw 20 inches
t 0.667 inches
h 40 inches
d 37 inches
be (1) 30.672 inches
be (2) 150 inches
be (3) 104 inches
be req 30.672 inches
wu 5.15 k/f
Mu 19312.5 kip-in
As min (1) 3.0398601942 sq-in
As min (2) 3.7 sq-in
a=t 0.667 inches
As 14.6307483216 sq-in
a 7.4824574353 inches

so design the beam as

T-beam

Asf 0.45378678 sq-inch

As1 14.1769615416 sq-inch
a web 11.1191855228 inches using As1 and bw
c 13.0813947327
Mn 16645.2558207 kip in

where a = aweb

Shear design
V 128.75 kips
Vx 112.870833333 kips
ɸVc 60.7972038831 kips
1/2 ɸVc 30.3986019415 kips

Shear design Required

Vs 3.7 kips Spacing 66 in c/c
Spacing (1) 18.5 inches
Spacing (2) 24 inches
Spacing (3) 88 inches

Req spacing 18.5

Doubly Reinforced Beam

L 18.5 f
b 9 inches
h 12 inches
d 9 inches
Wu 0.725 kips
Mu 372.196875 kip in 31.01640625 kip-f
Mn 34.4626736111 kip-f
assume a 10 inches Trial and error
As1 2.5847005208 sq in
a 4.504924655 inches
c 5.2999113589 inches
ᵨ 0.031909883
d, 2.8125 assume bar dia # 5 0.625 inches
To check wheather
compression steel yield
€s, 0.0014079922 Compression steel
€y 0.0013793103 yield

Mu/ɸbd2 699.5 psi for ᵨ 0.03190988

Mu1 458941.95 lb-in 38.2451625 kip-f Page 645 Str
Mn1 42.494625 kip-f design by
Mc Cormac
Mn2 -8.0319513889 kip-f
fs' 40.8317750183 ksi
Theoratical As' -0.3814949959 sq in using 3#7 bars 1.8 sq-in
As' -0.3894279461 sq-in
As 2.1952725747 sq-in using 6#9 bars 6

Mn 541.10803391 kip-in 45.0923361592 kip-f Desing OK

0.02032 Max area 2.468918

SF
20
15.945
15
1
14.1511875
10 2
5 3
4
0 0 5
0 2 4 6 8 10 12 14 16 Linear (5)
-5

-10
-14.1511875
-15.945
-15

-20

B.M
70
59.79375
60

50

40 B.M

30

20

10

0 0 0
0 5 10 15 20 25
40 B.M

30

20

10

0 0 0
0 5 10 15 20 25

for isolated T beam

Desing OK
 Corner
Design of square/rectangular column
Mid
fc 3 ksi 3000 psi
fy 40 ksi 40000 psi
W 12 inches
H 12 inches ɣ 0.75
Type Square
Condition Mid
ɸ 0.65
Pu 28.30 Kips
Assume %age of area 1 %
ɸPn 218.99 kips OK Pn 336.9 kips
Ast 1.44 sq-in
Using size of bar (#) 5
Ab 0.31 sq-in
No of bars 4.70
e 1.2 inches
Kn 0.78
Rn 0.078
ᵨ 0.01
circular
Square
Stair type Cantilever stairs
fy 60 ksi 60000 psi
fc 3 ksi 3000 psi
Span of stairs 20 f
Width of stairs 6f
Waist thickness 9.6 inches Provide 4 inch thickness
Tread width 12 inches
Riser 6 inches
Live load 100 lb/f
Self wt 87.5 lb/f
wt of plaster 15.625 lb/f 0.116892
w of marble 13.7666666667 lb/f
Wu 300.27 lb/f
Mu 5.40486 kip-f
d 6 inches
assume a 0.37 inches
As 0.2065485813 sq-in
a 0.4049972181
Minimum As 0.24 sq-in #4 bars 0.2 sq-in
Assume spacing 12 in c/c
As 0.2 sq-in
Mu 5.2177512518 kip-f Design Not Ok

Transverse reinforcement must be 0.1296 sq-in

provided to account for shrinkage

Assume spacing 18 in c/c

Using # 3 bars 0.11 sq-in
As 0.0733333333 sq-in Not OK
Simply supported
Cantilever stairs
 Simply supported bridge (Feed data in pink cell only)

Span 45 f
Road width curb to curb 9.5 f
fc 4000 psi
fy 60000 psi
Curb width 15 inches
Total width of bridge 12
Minimum thickness of deck 26.4 inches
Slab load 0.275 ksf
Wearing surface 0.035 ksf
Slab moments 69.609375 kip-f/f
Wearing surface moments 8.859375 kip-f/f
Live load moments
M truck 350 kip-f
M tandem 372 kip-f
M lane 98 kip-f
kip-f
Using greater load 372 kip-f
M LL+IM 592.76 kip-f
Design Lane width “E” for interior strip:
For single lane loaded E (inches) = 10.0 + 5.0 √ (L1W1)
L1 45 f
W1 12 f
E 10.5157916989 f
Design Lane width “E” for interior strip:
For multilane loaded: E (inches) = 84 + 1.44√ (L1W1) ≤ W1/NL
E (inches) = 84 + 1.44√ (L1W1) ≤ W1/NL
L1 45 f
W1 12 f
E 9.7885480093 f
W1/NL 12
Taking least E 9.7885480093 f
Interior Strip Moment (per foot) 60.5564787994 kip-f/f
Mu (interior strip)= 1.05 [1.25MDC + 1.5MDW + 1.75MLL+IM (per foot)] 2599.0602013 kip-in/f

Design lane width for edge strip: According to AASHTO LRFD

code A4.6.2.1.4,
E = Barrier width at base + 1 f + (1/2) strip width ≤ Full strip width
or 6 f (whichever is less) 7.1442740046 f
Taking least E 6f
Edge Strip Moment (per foot):
MLL+IM (Edge strip) per foot 59.276 kip f/f
Mu (edge strip) = 1.05 [1.25MDC + 1.5MDW + 1.75MLL+IM (per foot)] 214.23547031 kip f/f
Design for Interior strip
d 20.5 inch
Asmin 0.4752 sq-in
Ab 0.79 sq-in
spacing 5 inches
As 1.896 sq-in
a 2.7882352941 inches
Mn 1956.1366588 kip-in/f

Distribution reinforcement for interior strip (bottom transverse reinf)

The amount of bottom transverse reinforcement may be taken as a
percentage of the main reinforcement required for positive moment as
follows but not less than Shrinkage reinforcement
Atransverse = (100/√S or 50 %) of As (whichever is less) 50 %
100/√L 14.90711985 % of Main reinf
A transverse 0.2826389924 sq-in
Astmim (shrinkage)= 0.0018Ag 0.4752 sq-in
Assume spacing 8 in c/c
As 0.465 sq-in
Distribution reinforcement for interior strip (bottom transverse reinf)
Maximum spacing for temperature steel reinforcement in one way
slab according to ACI 7.12.2.2 is minimum of:
3hf 66 in c/c
Therefore #5 @ 8 inches c/c is OK.

Design for Edge strip:

Asmin 0.4752 sq-in
Ab 0.79 sq-in
spacing 4.5 inches
As 2.1066666667 sq-in
a 3.0980392157 inches
Mn 2155.8635294
Finally use #8 @ 4 inches c/c both for interior as well as edge strips

Distribution reinforcement for edge strip

A transverse 0.3140433248 sq-in
Astmim (shrinkage) 0.4752 sq-in
Ab 0.31 sq-in
spacing 8 inches
As 0.465
Maximum spacing for temperature steel reinforcement in one way
slab according to ACI 7.12.2.2 is minimum of
5hf
18″
Shrinkage and temperature reinforcement in top face of slab
(long and transverse both): For grade 60 steel
Ast = 0.0018Ag 0.4752 sq-in
 Truck load

# Design lanes 0.7916666667 say 1

4 ksi
60 ksi

22 inches

Tendam load

http://bendingmomentdiagram.com/solve/

Lane load

2570.82564375 kip-in/f
 Desig not ok

% of Main reinf

using # 5 bars 0.31 in2

18 in c/c

Design not ok
Slab information
Width 25 f
Length 28 f
m 0.8928571429
Thickness 6 inches
D.L of slab 0.1266666667 ksf
Live load on slab 0.015 ksf
Wu slab 0.176 ksf
coefficent for longer walls 0.6
Load of slab on longer wall 0.0528 ksf
Load of slab on shorter wall 0.0352 ksf
Beam Information
W 1f
D 1.5 f
D.L of beam 0.225 k/f
Factor.L of beam 0.27 k/f

Total load on longer walls 1.59 k/f

Total load on shorter walls 1.2556 k/f

If there is another slab supported by beam so do same exercise

for that one and add the two results
fy 60000 ksi
fc' 3000 psi
Beamw 12 inches
Beamd 18 inches de 16.125 inches
Clear span of beam (Ln) 24.5 f
Col(w) Shorter side 12 inches
Col(d) Longer side 12 inches
BEAM CHECKS

Factored axial comp force 23 kips

Agfc'/10 64.8 kips OK
Clear span to eff depth ratio 18.23256 OK
Width to depth ratio 0.666667 OK
Web width should not less than 10" 12 inches OK
Asmin 0.9675 in2 or 0.5299 in2
Asmax 4.8375 in2
1st stirrup should be at 2" or less, from
support
Stirrups spacing within 2h range and at
lapsplice 4.0 inches

Stirrups spacing within the other locations 8.1 inches

COLUMN CHECKS
Shorter to longer size ratio OK
Using # 5 bars in beam 0.625 inches
Provision for joints (min col size) 12.5 inches NOT OK
 Lower fibre Lower fibre Upper fibre Upper fibre
As+ 2
beam mid (in )
As+ 2
beam support (in )
As- 2
beam mid (in )
As-beam support (in2)
1.21 1.02 1.02 1.61
SMRF Checks OK OK OK
IMRF Checks OK
 Circular Water Tank Design

Capacity of tank 3000 Gallons

Free board 150 mm 6 in
Total Height 2.15 m 7f
Depth of water 2m
Area of tank 5.7 m2
Dia of tank 2.7 m 8.8 f
Thickness of core wall (t) 110 mm

26.9 KN T=Hw*D*rw/2
Max Hoop stressess at the
bottom of tank
Area of steel 179.2 mm2 As=T/allowablestress
Minimum steel req 495 mm2 As=.45%b*h
Spacing for #4 bar (horizontal bars) 260.6 mm c/c Ab=129 mm2

Check for Tensile stress

modular ratio m 13.3 m=Es/Ec
stress in concrete 0.23 N/mm2 S=T/1000(t)+(m-1)*Ast
Permissible stress in concrete 1.24 N/mm2 S=.27sqr(fc) Design is OK

Vertical Bars 264 mm2 As=.24%b*h

Spacing for # 3 bars 268.9 mm c/c Ab=71 mm2

Bottom slab thickness 150 mm

Min steel area 450 mm2 As=.30%b*h
Spacing for # 3 bars 157.8 mm c/c Bothways
Design
fc' 3000 psi
fy (Grade) 40 kips
long span 24 f
short span 20 f
size of column 20 inches

Type of slab Without interor

beams
Panel location Exterior panel

Without edge
Edge beam beams
without drop
Drop panel panels

ln 22.3 f
Min thickness of slab
Without edge beams with/without edge beam
With edge beams
without drop panel
with drop panel