Standard

Geometrical Tolerancing 1330-005

Lug Hole Page of Index
SPICER DRIVESHAFT EUROPE
1 1 AD
Richtlinien betreffend Urheberrecht Produkthaftung und Sicherheitshinweis siehe STD 1016-005

FREE FROM BURRS

AD
X

* = optional This Version is

** = assembly help measurement, non functional only for 787.75.

A2)+0.030 B +0.4 C D** E F min. G4) H1) J* K*

Size <SC> +0.3 min. +1.0 -0.5 +0.1 +0.5 max.

2025 34.894 37.15 35.00 45 2.5 2.50 100.85 94.95 35.00 60.00

2030 34.894 37.15 35.00 45 2.5 2.50 115.20 109.20 35.00 76.00

2035 5) 42.000 44.505) 42.10 57 2.5 2.50 129.00 123.00 42.10 74.30
Regulation concerning Copyright Productliability and Safety-Directions see STD 1016-000

2040
47.640 50.15 47.75 70 2.5 2.50 144.30 138.30 47.80 87.50
2040+
2045 / 2047
52.000 55.10 52.10 70 2.5 2.65 157.30 151.00 52.10 94.50
2045+ / 2047+
2055 / 2055+
57.000 60.10 57.10 77 2.5 2.65 162.30 156.00 57.10 93.50
587.42
2060
58.970 62.10 59.10 80 2.5 2.65 177.70 171.40 59.10 106.50
2060+
2065 / 2065+
65.000 68.10 65.10 85 3.0 3.50 185.00 177.00 65,10 102.50
587.48
587.35/36 57.000 60.10 57.10 - 2.5 2.50 154.00 148.00 57.10 93.60

587.20 48.000 50.50 48.10 - 2.5 2.00 125.00 119.80 48.10 88.00

587.30 52.000 55.10 52.10 - 2.5 2.50 143.00 137.00 52.10 94.50

787.75 72.000 75.00 72.10 - 3.5 - - 185.00 72.10 115.00

SPL 250 59.970 +0.025 63.10 60.10 85 2.5 2.65 173.70 167.00 60.10 100.00
1) The tolerance “H” is corresponding to the min. dimension and must be on the open end of the yoke
(by declination of the circlip groove)
2) The tolerance “A” is corresponding to the average dimension
(Amax = max. measure of a bore. Amin = min. measure of a bore) : (Amax + Amin) / 2
3) The testing of the circularity must be by the following formula: (Amax – Amin) / 2
Tolerance conception according to ISO 8015. Tolerance not specified ISO 2768m-K.
4) The tolerance “G” is valid for the area D
5) Dimension “B” optional 45.10
Prepared by Date Released by Date
M. Krischak 29.11.2018 H. Sarzaiem T. Stein 4. Quarter 2018
Spicer Gelenkwellenbau GmbH