Gujarat Technological University: Aeronautical Engineering Subject Code

GUJARAT TECHNOLOGICAL UNIVERSITY
AERONAUTICAL ENGINEERING
BASIC CONTROL THEORY
SUBJECT CODE: 2160104
B.E. 6thSEMESTER
Type of course: Engineering Science
Prerequisite: Basics of Maths
Rationale: In aircraft it is necessary to control three different types of axis i.e. yaw, pitch and roll. So in
order to control such axis it is necessary to understand the basic concepts of control and its detailed theory.
Teaching and Examination Scheme:
Teaching Scheme Credits Examination Marks Total

L T P C Theory Marks Practical Marks Marks
ESE PA (M) ESE (V) PA
(E) PA ALA ESE OEP (I)
3 0 2 5 70 20 10 20 10 20 150
Content:
Sr. No. Content Total % Weightage

Hrs
1 Unit 1:Introduction 2 10
Concept, Natural & Man made control systems, Open Loop & Closed
Loop systems
2 Unit 2: Mathematical models of systems 2 10
Modeling of mechanical systems, Modeling of electrical systems,
Examples.
3 Unit 3: Block Diagrams & Signal Flow 4 10
Properties of block diagrams, Block diagram reductions, Construction of
SFG, Mason’s Gain Formula
4 Unit 4: Time Domain Performance Analysis 6 20
Excitation functions, First Order, Second Order and Higher Order
Systems, Transient response, Steady State Error, Error constants, s- plane
root location and transient response, Time response of second order
system
5 Unit 5: Stability Analysis of Control Systems 6 10

Introduction, Bode’s Plot, Polar plots, Hurwits Criterion, Routh-Hurtwitz
criterion, Nyquist Plot, Nyquist Stability Criterion, Stability analysis,
Relative Stability, Closed Loop Frequency response of Unity feed Back
System.
6 Unit 6: Root Locus Method 4 10
Introduction, Root Locus plots, Rules for construction of root loci,
Feedback systems, Stability Conditions
7 Unit 7: State Space Analysis 7 10
Introduction, Comparison between modern control theory and
conventional control theory, concepts of State, State Variables and State
models, State Space Equations, Linear time-Invariant systems, State
model for single input single output linear system, State space
representation
8 Unit 8: Composite Controllers 5 20
Introduction, Proportional – Integral (PI) control, Proportional –
Derivative (PD) control, Proportional – Integral – Derivative (PID)
control, Special terminology, (proportional band, repeats per minute, rate
gain, direct action, reverse, action), desired features of a feedback control
algorithms, Proportional mode, integral mode, derivative mode.
Suggested Specification table with Marks (Theory):
Distribution of Theory Marks
R Level U Level A Level N Level E Level C Level

35% 25% 20% 15 5 0%
Legends: R: Remembrance; U: Understanding; A: Application, N: Analyze and E: Evaluate C: Create and

above Levels (Revised Bloom’s Taxonomy)
Note: This specification table shall be treated as a general guideline for students and teachers. The actual
distribution of marks in the question paper may vary slightly from above table.
Reference Books:
1. Control Systems By A. Anand Kumar

2. Control Theory By U. A. Bakshi & V. U. Bakshi
3. Process Control: Principles and Applications by Surekha Bhanot, Pub: Oxford University Press
4. Control Systems By Rao V Dukkipati.
5. Automatic Control Systems By Prof B. S. Manke
6. Process Control: Designing Processes and Control for Dynamic Performance by Thomas E. Marlin;
Pub: McGraw – Hill, International Edition
Course Outcome:
After learning the course the students should be able to:
1. Understand the basic concepts of control systems.

2. Know the procedure about how to analyze the problem.
3. Design the mathematical model of the system.
4. Design the composite types of controllers for any closed loop system.
List of Experiments:
Sr.
No.
Name of Practical Objective
To study about MATLAB software and its
application for Control System Analysis. Introduce MATLAB software for Control System.
1.
To study about various MATLAB commands
for Control System. Introduce various MATLAB commands for
2. Control System application.
To study about building and analyzing multi

block models. Introduce multi block models in MATLAB.
3.
To study about system time response to Unit
Step, Unit Impulse, Unit Ramp, Unit Parabolic Show the system behavior by using standard test
4. input signal. input signals.
To study the steady state error of type-zero, Show the behavior of type 0, type 1 and type 2
type-one and type-two control systems on system by using standard test input signals and
5. standard test input signals. understand which type of system is best.
To study about Bode plot and Nyquist plot for To learn various commands for stability analysis
stability analysis using MATLAB. used in Control System.
6.
To study about root locus for stability analysis
using MATLAB. To learn various commands for root locus
7. techniques used in control system MATLAB.
To study about Bode’s Plot for Frequency To understand about bode plot circuit kit for
Response Analysis. stability analysis used in Control System.
8.
To study about Liquid Level Controller using
Magnetic Float Type Liquid Level Sensor. Introduce the water level controller for real
9. application.
To study Simulation and Design using

MATLAB. To introduce Simulink in MATLAB based
10. application.
To prepare P, I, D algorithm on
MATLAB Simulink and visualize their Implement P, I, D algorithm on MATLAB
11. response to the Step Signal. Simulink.
Design based Problems (DP)/Open Ended Problem:
Designing of PID, PD and PI controllers and understand the behavior of the system with different input
signals.
Major Equipment: Matlab
List of Open Source Software/learning website: http://nptel.ac.in/
ACTIVE LEARNING ASSIGNMENTS: Preparation of power-point slides, which include videos,

animations, pictures, graphics for better understanding theory and practical work – The faculty will allocate
chapters/ parts of chapters to groups of students so that the entire syllabus to be covered. The power-point
slides should be put up on the web-site of the College/ Institute, along with the names of the students of the
group, the name of the faculty, Department and College on the first slide. The best three works should
submit to GTU.

Gujarat Technological University: Aeronautical Engineering Subject Code

Uploaded by

Copyright:

Available Formats

Gujarat Technological University: Aeronautical Engineering Subject Code

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Gujarat Technological University: Aeronautical Engineering Subject Code

Uploaded by

Copyright:

Available Formats

GUJARAT TECHNOLOGICAL UNIVERSITY

Type of course: Engineering Science

Prerequisite: Basics of Maths

Teaching and Examination Scheme:

Teaching Scheme Credits Examination Marks Total

Sr. No. Content Total % Weightage

5 Unit 5: Stability Analysis of Control Systems 6 10

Suggested Specification table with Marks (Theory):

Distribution of Theory Marks

R Level U Level A Level N Level E Level C Level

Legends: R: Remembrance; U: Understanding; A: Application, N: Analyze and E: Evaluate C: Create and

1. Control Systems By A. Anand Kumar

After learning the course the students should be able to:

1. Understand the basic concepts of control systems.

To study about building and analyzing multi

To study Simulation and Design using

Major Equipment: Matlab

List of Open Source Software/learning website: http://nptel.ac.in/

ACTIVE LEARNING ASSIGNMENTS: Preparation of power-point slides, which include videos,

You might also like