Strippers

allowing three inches of travel for adjustment and take-up of wear. The
rubber may also be adjusted easily by backing off the stud nuts and set-
ting tubing weight on top of the stripper. The flat top provides a suitable
Type ‘JU’ and ‘JU-H’ High Pressure Tubing
base for any Guiberson tubing spider. The Type ‘JU-H’ features a
Stripper hydraulic actuator which allows the stripper rubber to be compressed
This rugged stripper cleans oil and other materials from tubing as it is quickly and safely without stopping operations or going near the well-
being pulled and prevents escape of oil or gas while running or pulling head.
tubing under pressure. The stripper employs a heavy duty rubber that
can be changed without removing the stripper from the wellhead. The Also available is the Type ‘H’ actuator kit for installation on any Type
unique, accordion-style design of this rubber allows easy passage of tub- ‘JU’ stripper for full hydraulic operation.
ing couplings without leakage. The flexible, tight-gripping rubber works
equally well on round, square, or hexagonal shapes. The major compo-
nents are fabricated of tough cast steel for long, trouble-free service.

The housing of the Type ‘JU’ stripper is a single casting, with a flanged
bottom connection for easy attachment of API flanges. Six 1-1/8 in. stud
bolts transmit tubing load from the packing gland to the housing.
These bolts also provide the means for adjusting the packing rubber,

Type ‘JU-H’ Stripper

Type ‘JU’ Stripper

Rubber

Hydraulic Pump

Table 64: TYPE ‘JU’ AND ‘JU-H’ - ENGINEERING DATA Table 65: TYPE ‘H’ HYDRAULIC ACTUATOR -
ENGINEERING DATA
STANDARD METRIC

TYPE ‘JU’ TYPE ‘JU-H’ TYPE ‘JU’ TYPE ‘JU-H’ STANDARD METRIC
API NOMINAL FLANGE SIZE
TYPE ‘H’ HYDRAULIC ACTUATOR FOR ‘JU’ STRIPPER
AND SERIES 6 in. 2000 psi 6 in. 3000 psi 6 in. 3000 psi
152.4 152.4 152.4
13,800 kPa 20,000 kPa 20,000 kPa O.D. OF HYDRAULIC ACTUATOR 14 in. 355.6 mm
CASING SIZE 5 - 7 in. 5”- 7 in. 5 - 7 in. 127 - 178 mm 127 - 178 mm 127 - 178 mm HEIGHT (WITHOUT STUD BOLTS
13 in. 330.2 mm
MOUNTED ON IT)*
APPROXIMATE WEIGHT 280 lb 280 lb 415 lb 127 kg 127 kg 188 kg
HEIGHT (WITH STUD BOLTS
OVERALL HEIGHT 17-1/8 in. 17-1/8 in. 23-1/4 in. 435 mm 435 mm 590 mm 16 in. 406.4 mm
MOUNTED ON IT)
FLANGE O.D. 14 in. 15 in. 15 in. 355.6 mm 381 mm 381 mm APPROXIMATE WEIGHT (WITH-
230 lb 104.3 kg
FLANGE THICKNESS 1-7/8 in. 1-7/8 in. 1-7/8 in. 47.6 mm 47.6 mm 47.6 mm OUT STUD BOLTS OR NUTS)
BOLT CIRCLE DIAMETER 11-1/2 in. 12-1/2 in. 12-1/2 in. 292.1 mm 317.5 mm 317.5 mm APPROXIMATE WEIGHT (WITH
257 lb 116.6 kg
STUD BOLTS AND NUTS)
BOLT SIZE (TWELVE REQUIRED) 1 in. 1-1/8 in. 1-1/8 in. 25.4 mm 28.6 mm 28.6 mm
WORKING PRESSURE 1500 psi 1500 psi 1500 psi 10300 kPa 10300 kPa 10300 kPa
HYDRAULIC AREA 30.7 SQ. IN. 196 cm²
HYDRAULIC TRAVEL (USABLE) 3-1/2 in. 88.9 mm
TEST PRESSURE 3000 psi 3000 psi 3000 psi 20700 kPa 20700 kPa 20700 kPa
I.D. THROUGH HYDRAULIC ACTU-
MAXIMUM LOAD CAPACITY 40 tons 40 tons 40 tons 36290 kg 36290 kg 36290 kg 4-3/4 in. 120.7 mm
ATOR
OPENING THROUGH STRIPPER 6-1/8 in. 6-1/8 in. 4-3/4 in. 155.58 mm 155.58 mm 120.7 mm HYDRAULIC CONNECTION SIZE 1/4” in.NPT -
OPENING THROUGH HOUSING PUMP RESERVOIR SIZE 250 CU. IN./ 4098 cc/4.1 L
(WITHOUT HYDRAULIC ACTUATOR,
BOTTOM - - 6-1/8 in. - - 155.58 mm RECOMMENDED 8-3/4 PTS/1.1 GAL
SUPPORT PLATE, RUBBER, OR TOP MAXIMUM PUMP PRESSURE
SUPPORT PLATE IN PLACE) RECOMMENDED ON ACTUATOR 3000 psi 20700 kPa
RING JOINT GASSKET API NUMBER R-45 R-45 R-45 - - - * Stud bolts and nuts are not included in Type’H’ Hydraulic
RING JOINT GASKET PITCH DIAME- Actuator assembly. They are furnished on a Type ‘JH’ Tub-
8-5/16 in. 8-5/16 in. 8-5/16 in. 211.14 mm 211.14 mm 211.14 mm
TER ing Stripper as follows: 6 - Stripper Stud number 12598,
Stripper Nut number 12710

38
 Strippers
Table 66: TYPE ‘JU’ AND ‘JU-H’ STRIPPER - ENGINEERING DATA

ASSEMBLY NUMBER BY PIPE SIZE (in.)

STRIPPER TYPE AND FLANGE SIZE
1.900 2.063 2-3/8 2-7/8 3-1/2

’JU’, 6 in. 600-900-2000-3000 psi 12693 12693 12693 12697 17965

’JU-H’ 6 in. 600-900-2000-3000-psi - complete with pump and hose 80557 80557 80557 80558 80559
’JU-H’ 6 in. 600-900-2000-3000 psi - less pump and hose 69516 69516 69516 69517 69518

Type ‘H’ actuator kit only, less pump and hose, part number 69057; with pump and hose, part number 80576
Repair kits for Type ‘JU-H’ Tubing Stripper:
69524 Repair Kit for Hydraulic Actuator
68829 Repair Kit For Hydrualic Pump

Table 67: TYPE ‘JU’ STRIPPER - PART NUMBERS

DESCRIPTION QTY. REQUIRED PART NUMBER

GLAND LESS STUDS 1 12668 Gland

STUD 6 12598

STUD NUT 12 12710

TOP RUBBER SUPPORT 1

1.050 in. - 2-3/8 in. - 9568
2-7/8 in. - 9567
3 in. - 12037 Stud
RUBBER 1 *
1.050 in. - 1.660 in. TUBING (RBR. I.D. = 1.660 in.) - 24077
1.900 in. - 2-3/8 in. TUBING (RBR. I.D. = 2-1/4 in.) - 9444
2-7/8 in. TUBING (RBR. I.D. = 2-3/4 in.) - 9447
2-7/8 in. DRILL PIPE (RBR. I.D. = 3 in.) - 15154
3-1/2 in. TUBING (RBR. I.D. = 3-3/4 in.) - 16562

BOTTOM RUBBER SUPPORT 1 12455 Stud Nut

HOUSING
’JU’ 6-960-2000 PSI - 12873
’JU’. 6-2000-3000 PSI - 12875

RING JOINT GASKET (R-45) 1 19683 Top

Rubber
* Rubber and top rubber support must correspond in size
Support

Rubber

Bottom
Rubber
Support

Housing

Stud Nut

Parts - Type ‘JU’

Strippers 39
Strippers

Table 68: DIMENSION DATA & RECOMMENDED PIPE SIZES TO SEAL

OR PASS THROUGH TYPE JU AND JU-H STRIPPERS
SIZE DESIGNATION PART NUMBER NOMINAL I.D. (in.) API PIPE RECOMMENDED*
MAXIMUM
Pipe Size O.D. O.D. mm to
Pipe Joint O.D.
Pipe O.D. (in.) Rubber Top Support Rubber Top Support (in.) and Pass
(in.)
Designation
1.050-1.660 NUE 1.313-2.054
1.050-1.660 24077 9568 1.660 3.500 1.050-1.660 EUE 1.660-2.220 2.500
1.315-1.660 1.550-1.880
1.900-2 3/8 NUE 2.00-2.875
1.900-2 3/8 EUE 2.500-3.063
1.900- 2 3/8 9.444 9568 2.250 3.500 3.375
1.900-2.063 IJ 2.110-2.325
2 3/8 EU D.P. 2.656
2 7/8 NUE 3.500
2 7/8 EUE 3.460-3.668
2 7/8 9447 9567 2.750 4.125 3.750
2 7/8 IU D.P. 2.875
2 7/8 EU D.P. 3.219-3.250
2 7/8 NUE 3.500
3 15154 12037 3.000 4.750 2 7/8 EUE 3.460-3.660 4.125
2 7/8 EU D.P. 3.219-3.250
3 1/2 NUE
1.250
3 1/2 EUE
4.180-4.500
3 1/2 IU D.P.
3 1/2 16562 12037 3.750 4.750 3.500 4.625
3 1/2
3.824-4.000
EU D.P.
3.781
3 1/2 IEU D.P.

*Tubulars other than the API Tbg. and D.P. listed may be used if the pipe and joint O.D. fall within the dimensions shown in this chart.

Table 69: REPAIR KIT FOR STAR HYDRAULIC PUMP FOR

GUIBERSON TYPE JU-H TUBING STRIPPER (PART
NUMBER 68829)
DESCRIPTION QTY. REQUIRED
Release Valve (non-revised) Parts*
Release Valve Seal 1
9/32 in. Release Valve Ball (medium) 1
Pump Valve Parts
Pump Valve Seal 1
Pressure Ball Spring (Large) 1
Suction Ball Spring (Small) 1
1/4-in. Ball (Small) 1
3/8-in. Ball (Large) 1
Female Inserting Tool 1
Release Valve (REV.C) Parts*
Inner O-ring (Parker 2-106.) 1
Outer O-Ring (Parker 2-109) 1
Pump Piston Parts
Piston O-ring 1
Piston Back-Up Ring 1
Dust Seal (1 1/4-in. O.D. x 3/4-in. O.D.) 1
Barrel O-ring 1

* When repairing the release valve, look on the top of the pump oil
reservoir tank. If “REV. C” is NOT stenciled on the tank, use the
“non-revised” repair parts. If “REV.C” IS stenciled on the tank,
use the REV.C repair parts. In either case there will be two extra
parts in the kit to be discarded.

40
 Strippers

Pump Valve Repair Procedure

1. Stand pump upright then remove valve plug and valve seal.
2. Tilt pump to remove valve springs and balls. Allow oil to drain
through these valve holes to wash debris from the valve cham-
ber.
3. Lay pump on its side to inspect and clean valve chamber. Be
careful not to scratch or nick ball seats.
4. Insert new balls and springs into valve chamber in the proper
order (see illustration).
5. Insert pump valve seal, lip first into female inserting tool. 1/4" Ball (Small)
6. Place female inserting tool into valve chamber in the proper Suction Ball Spring (Small)
order (see illustration). Use a blunt ended object to push the
pump valve seal all the way through the inserting too. (Be sure 3/8" Ball (Large)
the inserting tool remains shouldered firmly in the hole.)
Pressure Ball Spring (Large)
7. Remove the inserting tool and screw in the valve seal plug.
Pump Valve Seal

Valve Seal Plug

Convenient Blunt
Ended Object

Female Inserting Tool

Pump Piston Repair Procedure

Leakage of oil around the pump piston indicated worn or
damaged packing.
1. Remove piston actuating linkage, piston, and barrel.
2. Remove and discard old packings and O-rings.
3. Clean all parts and dry with compressed air. Dip all parts in
clean hydraulic oil (including repair parts). Piston Actuating Linkage
4. Install new Barrel O-ring, Piston O-ring, Piston Back-Up Ring
and Dust Seal. Be sure Piston Back-Up Ring and Dust Seal are
oriented properly (see illustration).
5. Insert and tighten redressed barrel.
6. Open the release valve (to allow air to bleed out from the piston
barrel) and insert the redressed piston. Dust Seal
Pump Barrel
7. Replace piston linkage and bleed air from pump (see proce-
Pump Piston Piston
dure). Back-Up Ring

Piston O-Ring
Barrel O-Ring

Strippers 41
Strippers

Release Valve (non-revised)

Repair Procedure
Use these instructions IF the pump oil reservoir tank DOES
NOT have “REV.C” stenciled on the top.
1. Remove the release valve screw, release valve seal, and release
valve ball.
2. Clean and inspect the valve ball seat and release screw for
excessive deformation. If the release screw has been severely
damaged, it should be replaced.
3. Insert a new 9/32 in. release valve ball. This is the medium size
ball in the repair kit. (See illustration.)
4. Insert a new release valve seal.
5. Re-install the release valve screw. 9/32" Release Valve Ball
(Medium)

Release Valve Seal

Release Valve Screw

Release Valve (Revision C)

Repair Procedure
Use these instruction IF the pump oil reservoir tank DOES
have “REVC.” stenciled on the top.
1. Remove the release valve screw.
2. Remove the inner and outer o-rings from the release valve
screw.
3. Clean and inspect the release valve chamber and screw.
4. Install a new outer o-ring and inner o-ring on the release valve
screw (see illustration).
5. Re-install the release valve screw.

Inner O-Ring

Outer O-Ring

Release Valve Screw

42