Programming

Menu structure
Two menu levels are provided.

"Easy start up" level - factory setting

Access to basic parameters which define the characteristics of the application to manage: acceleration ramp, boost level.

"Advanced level"
Access to dedicated parameters which define the characteristics of the motor protections, interface, communication,…
This selection will add some menus and, in the particular case of Monitoring menu, it will add some parameters.

Menu selection: "Easy start up" level or "Advanced" level

1. Scroll up or down using the forward and backward keys until you reach conF menu and press the ENT key. This enters Configuration
menu.
2. Scroll up or down using the forward and backward keys until you reach LAC setting in conF menu and press the ENT key.
3. Select the desired parameter (oFF for the easy start up level or On for the advanced level) then press the ENT key. Repeat for each
level of submenus and parameters until you reach the desired parameter and value.
4. Press the ENT key to save the value.

Note: A parameter value becomes valid and takes effect immediately upon changing its value. If ESC is pressed, the value previously stored
in the EEPROM is restored.

Menu description
Easy start up level Advanced level

Status (1) Actual Data Status (1) Actual Data

conF Configuration conF Configuration

SEt Settings SEt Settings

AdJ Advanced
adjustments

SEt2 Advanced
Settings

PrO Advanced
protections

IO Advanced
I/O

COP Advanced
communication

SUP Advanced Advanced

monitoring SUP monitoring

UtIL Utility

(1) Status displays the state of the soft starter: rdY nrdY rUn.
See next page for Status menu.

46 BBV51330 08/2012
Programming

Status and actual data monitoring

Status Actual data

ACC
LCr1 Current phase 1 display, value in Amp
USF
nrdY
rdY
rUN LCr2 Current phase 2 display, value in Amp

LCr3 Current phase 3 display, value in Amp

Logic input status:

1=logic input ON Example: LI3 ON, LI2 OFF, LI1 OFF
LI
0=logic input OFF
Logic Output relays status (r2 and r1):
Lo 1=relay ON Example: R2 ON, R1 OFF
0=relay OFF

Note: When the soft starter is inside delta connection, LCr1, LCr2, LCr3 values are current inside the windings.
The line current = LCr x 3.

Status Description
ACC During acceleration
tbS The soft starter has tripped in SnbF, too many starts, see Diagnostics/Troubleshooting page 76.
dEC During deceleration
nrdY A stop command is present, with line and control power on
LI1 = 0 and LI2 = 1 in 2-wire control
LI1 = 1 and LI2 = 1 at power up in 3-wire control
Or main power is switched off
rdY Soft starter is ready to start
rUn Steady state, the bypass contactor is closed

For the trip codes, see chapter Diagnostics / Troubleshooting page 75.

BBV51330 08/2012 47
List of parameters

Parameters access control

• R (Read): parameter value on read ONLY.
• R/W (Read/Write): Parameter value can be changed when motor is running (except during soft start and soft stop when command is
given by Modbus).
• R/W* (Read/Write): parameter value can be changed only when the soft starter is stopped.
Code Description R/W Code Description R/W
Actual data PrO Advanced Protections (continued) (1)
LCr1 Current phase 1 display (p. 47) R PHr Phase sequence (p. 57) R/W*
LCr2 Current phase 2 display (p. 47) R PHL Phase loss detection (p. 58) R/W
LCr3 Current phase 3 display (p. 47) R USd Under voltage threshold (p. 58) R/W
LI Logic input status (p. 47) R USt Under voltage time delay (p. 58) R/W
Lo Logic Output relays status (p. 47) R OSd Over voltage threshold (p. 59) R/W
OSt Over voltage time delay (p. 59) R/W
conF Configuration PtC PTC probes motor monitoring (p. 59) R/W
IcL Soft starter rated current (p. 50) R ItH Overload protection (p. 59) R/W*
dLtA Connection type (line or delta) (p. 50) R/W*
Uln Line voltage (p. 50) R/W IO Advanced IO (1)
In Motor rated current (p. 50) R/W* LI2 Logic input 2 (p. 60) R/W*
Cod Setting lock (p. 50) R/W LI3 Logic input 3 (p. 60) R/W*
LAC Advanced mode (p. 50) R/W r1 Relay 1 (p. 61) R/W*
r2 Relay 2 (p. 61) R/W*
SEt Settings FAn Fan management (p. 61) R/W
t90 Initial voltage (p. 51) R/W
ILt Current limit (p. 51) R/W COP Advanced communication (1)
tLS Max start time (p. 51) R/W Add Modbus address (p. 62) R/W*
ACC Acceleration time (p. 52) R/W tbr Modbus baudrate (p. 62) R/W*
dEC Deceleration time (p. 52) R/W For Modbus format (p. 62) R/W*
EdC End of deceleration (p. 52) R/W ttO Modbus time out (p. 62) R/W*
tHP Motor thermal protection (p. 52) R/W CtrL Command channel (p. 62) R/W*

AdJ Advanced adjustements (1) SUP Advanced monitoring

Snb Number of starts (p. 53) R/W StPr Last starting time (p. 63) R
SLG Starts period (p. 53) R/W SICL Last start maximum current (p. 63) R
bSt Boost time (p. 53) R/W LFt Last trip (p. 63) R
SSC Start-stop control (p. 54) R/W* dICL Trip current (p. 63) R
SPCU Start-stop profile control voltage (p. 54) R/W* rnt Total run time (p. 63) R
Stnb Total number of starts (p. 63) R
SEt2 Advanced settings (1) dEFt Total number of trips (p. 63) R
t92 2nd initial voltage (p. 55) R/W dEF1 Trip history 1 (p. 63) R
ILt2 2nd current limit (p. 55) R/W dEF2 Trip history 2 (1) (p. 63) R
ACC2 2nd acceleration time (p. 55) R/W dEF3 Trip history 3 (1) (p. 63) R
dEC2 2nd deceleration time (p. 55) R/W dEF4 Trip history 4 (1) (p. 63) R
In2 2nd motor rated Current (p. 55) R/W* dEF5 Trip history 5 (1) (p. 63) R
dEF6 Trip history 6 (1) (p. 63) R
PrO Advanced Protections (1) dEF7 Trip history 7 (1) (p. 63) R
UId Under current threshold (p. 56) R/W dEF8 Trip history 8 (1) (p. 63) R
UIt Under current time delay (p. 56) R/W dEF9 Trip history 9 (1) (p. 63) R
OId Overcurrent threshold (p. 56) R/W
OIt Overcurrent time delay (p. 57) R/W UtIL Utility (2)
Ubd Unbalance threshold (p. 57) R/W tESt Soft starter self test (p. 64) R/W*
Ubt Unbalance time delay (p. 57) R/W UdP Soft starter software version (p. 64) R
Grdd Ground leakage current threshold (p. 57) R/W FCS Back to factory settings (p. 64) R/W*
Grdt Ground leakage current time delay (p. 57) R/W rPr Reset of trip history and counters (p. 64) R/W*

(1) Only available when Advanced mode LAC page 50 is set (2) Accessible, except motor in run state, using the key shortcut
to On
ESC +

48 BBV51330 08/2012