Notice for TAIYO YUDEN Products [ For General Electronic Equipment ]

Please read this notice before using the TAIYO YUDEN products.

REMINDERS

■ Product information in this catalog is as of October 2018. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully
before practical application or use of our products.

Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or
equipment incorporating our products, which are caused under the conditions other than those specified in this
catalog or individual product specification sheets.

■ Please contact TAIYO YUDEN for further details of product specifications as the individual product specification
sheets are available.

■ Please conduct validation and verification of our products in actual condition of mounting and operating
environment before using our products.

■ The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA
equipment, home electric appliances, office equipment, information and communication equipment including,
without limitation, mobile phone, and PC) and medical equipment classified as Class I or II by IMDRF. Please be
sure to contact TAIYO YUDEN for further information before using the products for any equipment which may
directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation,
automotive powertrain control system, train control system, and ship control system, traffic signal equipment,
disaster prevention equipment, medical equipment classified as Class III by IMDRF, highly public information
network equipment including, without limitation, telephone exchange, and base station).

Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g.,
aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control
equipment, undersea equipment, military equipment).

*Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g.,
in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN.
Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment.

When our products are used even for high safety and/or reliability-required devices or circuits of general electronic
equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to
install a protection circuit as necessary.

Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way
responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog
for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above.

■ Information contained in this catalog is intended to convey examples of typical performances and/or applications
of our products and is not intended to make any warranty with respect to the intellectual property rights or any
other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights.

■ Please note that the scope of warranty for our products is limited to the delivered our products themselves and
TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products.
Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality
assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in
accordance with such agreement.

■ The contents of this catalog are applicable to our products which are purchased from our sales offices or
authorized distributors (hereinafter“TAIYO YUDEN’
s official sales channel”). Please note that the contents of this
catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’ s official sales
channel.

■ Caution for Export

Some of our products listed in this catalog may require specific procedures for export according to“U.S. Export
Administration Regulations”,“Foreign Exchange and Foreign Trade Control Law”of Japan, and other applicable
regulations. Should you have any questions on this matter, please contact our sales staff.

19
MULTILAYER CHIP INDUCTORS FOR HIGH FREQUENCY APPLICATIONS(HK SERIES)
MULTILAYER CHIP INDUCTORS FOR HIGH FREQUENCY APPLICATIONS（HK SERIES）
WAVE＊
WAVE* REFLOW
REFLOW
＊Except for HK0603, HK1005
*Except for HK0603, HK1005
■PARTS NUMBER * Operating Temp.：-55～+125℃（HK1608/2125：-40～+85℃）

H K △ 0 6 0 3 △ 1 0 N J － T △＝Blank space
① ② ③ ④ ⑤

①Series name ③Nominal inductance

Code Series name Code
Nominal inductance［nH］
Multilayer chip inductor for high frequency （example）
HK△
applications 3N9 3.9
10N 10.0
②Dimensions（L×W） R10 100

INDUCTORS
Dimensions R12 120
Code Type（inch）
（L×W）［mm］ ※R＝Decimal point
0603 0603（0201） 0.6×0.3 ※N＝0.0（nH type）
1005 1005（0402） 1.0×0.5
1608 1608（0603） 1.6×0.8 ④Inductance tolerance
Code Inductance tolerance

／ INDUCTORS FOR HIGH FREQUENCY APPLICATIONS

2125 2125（0805） 2.0×1.2
J ±5％
S ±0.3nH

⑤Packaging
Code Packaging
－T Taping

■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY

W
L

Standard quantity［pcs］
Type L W T e
Paper tape Embossed tape
HK 0603 0.6±0.03 0.3±0.03 0.3±0.03 0.15±0.05
15000 －
（0201） （0.024±0.001） （0.012±0.001） （0.012±0.001） （0.006±0.002）
HK 1005 1.0±0.05 0.5±0.05 0.5±0.05 0.25±0.10
10000 －
（0402） （0.039±0.002） （0.020±0.002） （0.020±0.002） （0.010±0.004）
HK 1608 1.6±0.15 0.8±0.15 0.8±0.15 0.3±0.2
4000 －
（0603） （0.063±0.006） （0.031±0.006） （0.031±0.006） （0.012±0.008）
2.0＋0.3/－0.1 1.25±0.2 0.85±0.2 0.5±0.3
－ 4000
HK 2125 （0.079＋0.012/－0.004） （0.049±0.008） （0.033±0.008） （0.020±0.012）
（0805） 2.0＋0.3/－0.1 1.25±0.2 1.0＋0.2/－0.3 0.5±0.3
－ 3000
（0.079＋0.012/－0.004） （0.049±0.008） （0.039＋0.008/－0.012） （0.020±0.012）
Unit：mm（inch）

i_mlci_HK_e-E05R01

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .

19 99
 ■PARTS NUMBER

●HK 0603
Nominal LQ Measuring Q（Typical）frequency［MHｚ］ Self-resonant DC Resistance
Inductance Q frequency ［MHｚ］ ［Ω］ Rated current Thickness
Parts number EHS inductance frequency
tolerance ※） （min.） ［mA］（max.） ［mm］
［nH］ ［MHz］ 100 300 500 800 1000 （min.） （typ.） （max.） （typ.）
HK 0603 1N0[]-T RoHS 1.0 ±0.3nH 4 100 6 12 17 22 27 10000 > 13000 0.11 0.088 470 0.30 ±0.03
HK 0603 1N2[]-T RoHS 1.2 ±0.3nH 4 100 6 12 16 21 25 10000 > 13000 0.12 0.089 450 0.30 ±0.03
HK 0603 1N5[]-T RoHS 1.5 ±0.3nH 4 100 6 12 15 20 23 10000 > 13000 0.13 0.11 430 0.30 ±0.03
HK 0603 1N8[]-T RoHS 1.8 ±0.3nH 4 100 6 12 15 20 23 10000 > 13000 0.16 0.12 390 0.30 ±0.03
HK 0603 2N0[]-T RoHS 2.0 ±0.3nH 4 100 6 12 15 20 22 10000 > 13000 0.17 0.13 380 0.30 ±0.03
HK 0603 2N2[]-T RoHS 2.2 ±0.3nH 4 100 6 12 15 20 22 8800 12500 0.19 0.14 360 0.30 ±0.03
HK 0603 2N4[]-T RoHS 2.4 ±0.3nH 4 100 6 12 15 20 22 8300 11700 0.20 0.15 350 0.30 ±0.03
HK 0603 2N7[]-T RoHS 2.7 ±0.3nH 5 100 7 12 15 20 22 7700 11000 0.21 0.16 340 0.30 ±0.03
HK 0603 3N0[]-T RoHS 3.0 ±0.3nH 5 100 7 12 15 20 22 7200 11000 0.22 0.18 330 0.30 ±0.03
HK 0603 3N3[]-T RoHS 3.3 ±0.3nH 5 100 7 12 15 20 22 6700 9600 0.23 0.19 320 0.30 ±0.03
HK 0603 3N6[]-T RoHS 3.6 ±0.3nH 5 100 7 12 15 20 22 6400 9100 0.25 0.20 310 0.30 ±0.03
HK 0603 3N9[]-T RoHS 3.9 ±0.3nH 5 100 7 12 15 20 22 6000 8600 0.27 0.20 300 0.30 ±0.03
HK 0603 4N3[]-T RoHS 4.3 ±0.3nH 5 100 7 12 15 19 21 5700 8100 0.30 0.22 280 0.30 ±0.03
HK 0603 4N7[]-T RoHS 4.7 ±0.3nH 5 100 7 12 15 19 21 5300 7600 0.30 0.24 280 0.30 ±0.03
HK 0603 5N1[]-T RoHS 5.1 ±0.3nH 5 100 7 12 15 19 21 5000 7100 0.33 0.26 270 0.30 ±0.03
HK 0603 5N6[]-T RoHS 5.6 ±0.3nH 5 100 7 12 15 19 21 4600 6600 0.36 0.27 260 0.30 ±0.03
INDUCTORS

HK 0603 6N2[]-T RoHS 6.2 ±0.3nH 5 100 7 11 14 18 20 4200 6100 0.38 0.29 250 0.30 ±0.03
HK 0603 6N8[]-T RoHS 6.8 ±5％ 5 100 7 11 14 18 20 3900 5600 0.39 0.30 250 0.30 ±0.03
HK 0603 7N5[]-T RoHS 7.5 ±5％ 5 100 7 11 14 18 19 3600 5300 0.41 0.34 240 0.30 ±0.03
HK 0603 8N2[]-T RoHS 8.2 ±5％ 5 100 7 11 14 18 19 3400 4900 0.45 0.34 230 0.30 ±0.03
HK 0603 9N1[]-T RoHS 9.1 ±5％ 5 100 7 11 14 17 18 3200 4600 0.48 0.40 220 0.30 ±0.03
HK 0603 10N[]-T RoHS 10 ±5％ 5 100 7 11 14 17 18 2900 4200 0.51 0.41 220 0.30 ±0.03
HK 0603 12N[]-T RoHS 12 ±5％ 5 100 7 11 14 17 18 2700 3800 0.68 0.45 190 0.30 ±0.03
／ INDUCTORS FOR HIGH FREQUENCY APPLICATIONS

HK 0603 15N[]-T RoHS 15 ±5％ 5 100 7 11 13 16 17 2300 3300 0.71 0.50 180 0.30 ±0.03
HK 0603 18N[]-T RoHS 18 ±5％ 5 100 7 11 13 16 17 2100 3000 0.81 0.57 170 0.30 ±0.03
HK 0603 22N[]-T RoHS 22 ±5％ 5 100 7 11 13 15 16 1800 2600 1.00 0.71 150 0.30 ±0.03
HK 0603 27N[]-T RoHS 27 ±5％ 4 100 6 10 12 14 15 1800 2600 1.35 1.11 120 0.30 ±0.03
HK 0603 33N[]-T RoHS 33 ±5％ 4 100 6 10 12 14 14 1700 2400 1.47 1.33 110 0.30 ±0.03
HK 0603 39N[]-T RoHS 39 ±5％ 4 100 6 10 12 13 12 1500 2100 1.72 1.51 100 0.30 ±0.03
HK 0603 47N[]-T RoHS 47 ±5％ 4 100 6 10 11 12 11 1300 1800 1.90 1.74 100 0.30 ±0.03
HK 0603 56N[]-T RoHS 56 ±5％ 4 100 6 10 11 11 10 1100 1600 2.27 1.85 80 0.30 ±0.03
HK 0603 68N[]-T RoHS 68 ±5％ 4 100 6 10 11 11 10 1100 1500 2.66 2.30 80 0.30 ±0.03
HK 0603 82N[]-T RoHS 82 ±5％ 4 100 6 10 11 10 8 1000 1400 3.37 2.60 70 0.30 ±0.03
HK 0603 R10[]-T RoHS 100 ±5％ 4 100 6 9 10 9 6 900 1200 3.74 3.00 60 0.30 ±0.03
※ [] mark indicates the Inductance tolerance code. Please refer for the inductance tolerance except the above.

●HK 1005
Self-resonant DC Resistance Rated current
Nominal LQ Measuring Q（Typical）frequency［MHｚ］ frequency ［MHｚ］ ［Ω］ ［mA］（max.）
Inductance Q Thickness
Parts number EHS inductance frequency
tolerance ※） （min.） -55～ -55～ ［mm］
［nH］ ［MHz］ 100 300 500 800 1000 （min.） （typ.） （max.） （typ.）
+125℃ +85℃
HK 1005 1N0[]-T RoHS 1.0 ±0.3nH 8 100 11 25 34 43 52 10000 > 13000 0.08 0.04 300 900 0.50 ±0.05
HK 1005 1N2[]-T RoHS 1.2 ±0.3nH 8 100 11 25 35 44 52 10000 > 13000 0.09 0.04 300 900 0.50 ±0.05
HK 1005 1N5[]-T RoHS 1.5 ±0.3nH 8 100 11 24 33 44 48 6000 > 13000 0.10 0.05 300 850 0.50 ±0.05
HK 1005 1N8[]-T RoHS 1.8 ±0.3nH 8 100 11 23 30 36 42 6000 11000 0.12 0.06 300 700 0.50 ±0.05
HK 1005 2N0[]-T RoHS 2.0 ±0.3nH 8 100 11 21 27 34 39 6000 10500 0.12 0.06 300 700 0.50 ±0.05
HK 1005 2N2[]-T RoHS 2.2 ±0.3nH 8 100 10 18 25 31 36 6000 10000 0.13 0.07 300 700 0.50 ±0.05
HK 1005 2N4[]-T RoHS 2.4 ±0.3nH 8 100 10 18 24 31 35 6000 9500 0.13 0.07 300 650 0.50 ±0.05
HK 1005 2N7[]-T RoHS 2.7 ±0.3nH 8 100 10 18 24 31 34 6000 9000 0.13 0.08 300 650 0.50 ±0.05
HK 1005 3N0[]-T RoHS 3.0 ±0.3nH 8 100 10 18 24 31 35 6000 8500 0.16 0.09 300 600 0.50 ±0.05
HK 1005 3N3[]-T RoHS 3.3 ±0.3nH 8 100 10 18 24 31 35 6000 8000 0.16 0.10 300 550 0.50 ±0.05
HK 1005 3N6[]-T RoHS 3.6 ±0.3nH 8 100 10 18 24 31 35 5000 7500 0.20 0.11 300 500 0.50 ±0.05
HK 1005 3N9[]-T RoHS 3.9 ±0.3nH 8 100 10 18 24 31 35 4000 7000 0.21 0.12 300 500 0.50 ±0.05
HK 1005 4N3[]-T RoHS 4.3 ±0.3nH 8 100 10 18 24 31 35 4000 6500 0.20 0.12 300 500 0.50 ±0.05
HK 1005 4N7[]-T RoHS 4.7 ±0.3nH 8 100 10 18 24 31 34 4000 6000 0.21 0.12 300 500 0.50 ±0.05
HK 1005 5N1[]-T RoHS 5.1 ±0.3nH 8 100 10 18 24 31 34 4000 5800 0.21 0.13 300 450 0.50 ±0.05
HK 1005 5N6[]-T RoHS 5.6 ±0.3nH 8 100 10 18 24 30 35 4000 5700 0.23 0.15 300 430 0.50 ±0.05
HK 1005 6N2[]-T RoHS 6.2 ±0.3nH 8 100 10 18 24 30 34 3900 5600 0.25 0.16 300 430 0.50 ±0.05
HK 1005 6N8[]-T RoHS 6.8 ±5％ 8 100 10 18 23 29 32 3900 5500 0.25 0.17 300 430 0.50 ±0.05
HK 1005 7N5[]-T RoHS 7.5 ±5％ 8 100 10 18 23 29 32 3700 5200 0.25 0.18 300 400 0.50 ±0.05
HK 1005 8N2[]-T RoHS 8.2 ±5％ 8 100 10 18 23 29 31 3600 4900 0.28 0.21 300 380 0.50 ±0.05
HK 1005 9N1[]-T RoHS 9.1 ±5％ 8 100 10 18 23 29 31 3400 4500 0.30 0.22 300 360 0.50 ±0.05
HK 1005 10N[]-T RoHS 10 ±5％ 8 100 10 18 23 29 31 3200 4300 0.31 0.23 300 340 0.50 ±0.05
HK 1005 12N[]-T RoHS 12 ±5％ 8 100 11 18 23 29 31 2700 3900 0.40 0.28 300 330 0.50 ±0.05
HK 1005 15N[]-T RoHS 15 ±5％ 8 100 11 18 23 28 30 2300 3500 0.46 0.31 300 320 0.50 ±0.05
HK 1005 18N[]-T RoHS 18 ±5％ 8 100 11 18 23 28 30 2100 3100 0.55 0.35 300 310 0.50 ±0.05
HK 1005 22N[]-T RoHS 22 ±5％ 8 100 11 17 22 26 27 1900 2800 0.60 0.42 300 300 0.50 ±0.05
HK 1005 27N[]-T RoHS 27 ±5％ 8 100 11 17 21 25 26 1600 2300 0.70 0.47 300 300 0.50 ±0.05
HK 1005 33N[]-T RoHS 33 ±5％ 8 100 11 16 20 23 22 1300 1900 0.80 0.50 200 250 0.50 ±0.05
HK 1005 39N[]-T RoHS 39 ±5％ 8 100 11 16 20 23 21 1200 1700 0.90 0.52 200 250 0.50 ±0.05
HK 1005 47N[]-T RoHS 47 ±5％ 8 100 11 16 19 21 18 1000 1500 1.00 0.58 200 230 0.50 ±0.05
HK 1005 56N[]-T RoHS 56 ±5％ 8 100 11 16 18 18 16 750 1300 1.00 0.61 200 220 0.50 ±0.05
HK 1005 68N[]-T RoHS 68 ±5％ 8 100 11 15 17 18 11 750 1200 1.20 0.70 180 200 0.50 ±0.05
HK 1005 82N[]-T RoHS 82 ±5％ 8 100 10 14 16 15 6 600 1100 1.30 0.81 150 200 0.50 ±0.05
HK 1005 R10[]-T RoHS 100 ±5％ 8 100 10 14 14 12 － 600 1000 1.50 0.94 150 200 0.50 ±0.05
HK 1005 R12[]-T RoHS 120 ±5％ 8 100 10 12 10 － － 600 800 1.60 1.10 150 200 0.50 ±0.05
HK 1005 R15[]-T RoHS 150 ±5％ 8 100 12 17 17 － － 550 920 3.20 2.57 140 200 0.50 ±0.05
HK 1005 R18[]-T RoHS 180 ±5％ 8 100 12 16 － － － 500 810 3.70 2.97 130 200 0.50 ±0.05
HK 1005 R22[]-T RoHS 220 ±5％ 8 100 12 16 － － － 450 700 4.20 3.29 120 200 0.50 ±0.05
HK 1005 R27[]-T RoHS 270 ±5％ 8 100 12 14 － － － 400 600 4.80 3.92 110 200 0.50 ±0.05
※ [] mark indicates the Inductance tolerance code. Please refer for the inductance tolerance except the above.

i_mlci_HK_e-E05R01

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .

100 19
■PARTS NUMBER

●HK 1608
Nominal LQ Measuring Q（Typical）frequency［MHｚ］ Self-resonant DC Resistance
Inductance Q frequency ［MHｚ］ ［Ω］ Rated current Thickness
Parts number EHS inductance frequency
tolerance ※） （min.） ［mA］（max.） ［mm］
［nH］ ［MHz］ 100 300 500 800 1000 （min.） （typ.） （max.） （typ.）
HK 1608 1N0[]-T RoHS 1.0 ±0.3nH 8 100 14 30 40 70 90 10000 > 13000 0.05 0.015 300 0.80 ±0.15
HK 1608 1N2[]-T RoHS 1.2 ±0.3nH 8 100 14 30 40 70 90 10000 > 13000 0.05 0.015 300 0.80 ±0.15
HK 1608 1N5[]-T RoHS 1.5 ±0.3nH 8 100 14 26 34 47 50 6000 > 13000 0.10 0.03 300 0.80 ±0.15
HK 1608 1N8[]-T RoHS 1.8 ±0.3nH 8 100 10 18 24 30 34 6000 > 13000 0.10 0.06 300 0.80 ±0.15
HK 1608 2N2[]-T RoHS 2.2 ±0.3nH 8 100 12 22 29 37 40 6000 12000 0.10 0.06 300 0.80 ±0.15
HK 1608 2N7[]-T RoHS 2.7 ±0.3nH 10 100 13 24 32 41 45 6000 11000 0.10 0.06 300 0.80 ±0.15
HK 1608 3N3[]-T RoHS 3.3 ±0.3nH 10 100 14 25 33 42 47 6000 9000 0.12 0.06 300 0.80 ±0.15
HK 1608 3N9[]-T RoHS 3.9 ±0.3nH 10 100 13 25 33 42 46 6000 8000 0.14 0.07 300 0.80 ±0.15
HK 1608 4N7[]-T RoHS 4.7 ±0.3nH 10 100 13 25 33 42 47 4000 6500 0.16 0.08 300 0.80 ±0.15
HK 1608 5N6[]-T RoHS 5.6 ±0.3nH 10 100 14 25 33 42 46 4000 5800 0.18 0.09 300 0.80 ±0.15
HK 1608 6N8[]-T RoHS 6.8 ±5％ 10 100 14 25 33 43 47 4000 5600 0.22 0.11 300 0.80 ±0.15
HK 1608 8N2[]-T RoHS 8.2 ±5％ 10 100 14 26 34 44 48 3500 5200 0.24 0.13 300 0.80 ±0.15
HK 1608 10N[]-T RoHS 10 ±5％ 12 100 14 26 34 43 47 3400 4600 0.26 0.16 300 0.80 ±0.15
HK 1608 12N[]-T RoHS 12 ±5％ 12 100 14 27 35 45 49 2600 4000 0.28 0.17 300 0.80 ±0.15
HK 1608 15N[]-T RoHS 15 ±5％ 12 100 15 28 37 46 51 2300 3400 0.32 0.20 300 0.80 ±0.15
HK 1608 18N[]-T RoHS 18 ±5％ 12 100 15 27 36 44 48 2000 3000 0.35 0.21 300 0.80 ±0.15

INDUCTORS
HK 1608 22N[]-T RoHS 22 ±5％ 12 100 16 28 36 44 47 1600 2900 0.40 0.25 300 0.80 ±0.15
HK 1608 27N[]-T RoHS 27 ±5％ 12 100 16 29 37 45 46 1400 2200 0.45 0.28 300 0.80 ±0.15
HK 1608 33N[]-T RoHS 33 ±5％ 12 100 17 31 40 46 47 1200 1800 0.55 0.35 300 0.80 ±0.15
HK 1608 39N[]-T RoHS 39 ±5％ 12 100 18 31 39 44 44 1100 1600 0.60 0.38 300 0.80 ±0.15
HK 1608 47N[]-T RoHS 47 ±5％ 12 100 17 28 34 35 34 900 1600 0.70 0.45 300 0.80 ±0.15
HK 1608 56N[]-T RoHS 56 ±5％ 12 100 17 28 34 34 31 900 1400 0.75 0.50 300 0.80 ±0.15
HK 1608 68N[]-T RoHS 68 ±5％ 12 100 18 29 34 30 22 700 1200 0.85 0.55 300 0.80 ±0.15

／ INDUCTORS FOR HIGH FREQUENCY APPLICATIONS

HK 1608 82N[]-T RoHS 82 ±5％ 12 100 18 28 33 27 － 600 1100 0.95 0.60 300 0.80 ±0.15
HK 1608 R10[]-T RoHS 100 ±5％ 12 100 18 27 28 16 － 600 1000 1.00 0.65 300 0.80 ±0.15
HK 1608 R12[]-T RoHS 120 ±5％ 8 50 16 24 23 － － 500 800 1.20 0.68 300 0.80 ±0.15
HK 1608 R15[]-T RoHS 150 ±5％ 8 50 13 19 16 － － 500 800 1.20 0.73 300 0.80 ±0.15
HK 1608 R18[]-T RoHS 180 ±5％ 8 50 13 18 12 － － 400 700 1.30 0.85 300 0.80 ±0.15
HK 1608 R22[]-T RoHS 220 ±5％ 8 50 12 16 － － － 400 600 1.50 0.95 300 0.80 ±0.15
HK 1608 R27[]-T RoHS 270 ±5％ 8 50 14 15 － － － 400 550 1.90 1.34 150 0.80 ±0.15
HK 1608 R33[]-T RoHS 330 ±5％ 8 50 14 － － － － 350 480 2.10 1.53 150 0.80 ±0.15
HK 1608 R39[]-T RoHS 390 ±5％ 8 50 13 － － － － 350 410 2.30 1.72 150 0.80 ±0.15
HK 1608 R47[]-T RoHS 470 ±5％ 8 50 13 － － － － 300 360 2.60 2.04 150 0.80 ±0.15
※ [] mark indicates the Inductance tolerance code. Please refer for the inductance tolerance except the above.

●HK 2125
Nominal LQ Measuring Q（Typical）frequency［MHｚ］ Self-resonant DC Resistance
Inductance Q frequency ［MHｚ］ ［Ω］ Rated current Thickness
Parts number EHS inductance frequency
tolerance （min.） ［mA］（max.） ［mm］
［nH］ ［MHz］ 100 300 500 800 1000 （min.） （typ.） （max.） （typ.）
HK 2125 1N5S-T RoHS 1.5 ±0.3nH 10 100 21 39 57 61 68 4000 > 6000 0.10 0.02 300 0.85 ±0.2
HK 2125 1N8S-T RoHS 1.8 ±0.3nH 10 100 18 35 49 55 59 4000 > 6000 0.10 0.02 300 0.85 ±0.2
HK 2125 2N2S-T RoHS 2.2 ±0.3nH 10 100 18 33 46 53 58 4000 > 6000 0.10 0.03 300 0.85 ±0.2
HK 2125 2N7S-T RoHS 2.7 ±0.3nH 12 100 19 36 50 56 60 4000 > 6000 0.10 0.03 300 0.85 ±0.2
HK 2125 3N3S-T RoHS 3.3 ±0.3nH 12 100 16 29 40 47 51 4000 > 6000 0.13 0.04 300 0.85 ±0.2
HK 2125 3N9S-T RoHS 3.9 ±0.3nH 12 100 18 33 46 54 60 4000 > 6000 0.15 0.05 300 0.85 ±0.2
HK 2125 4N7S-T RoHS 4.7 ±0.3nH 12 100 18 34 46 55 60 3500 > 6000 0.20 0.05 300 0.85 ±0.2
HK 2125 5N6S-T RoHS 5.6 ±0.3nH 15 100 20 38 51 60 66 3200 5400 0.23 0.05 300 0.85 ±0.2
HK 2125 6N8J-T RoHS 6.8 ±5％ 15 100 20 39 52 63 69 2800 4200 0.25 0.06 300 0.85 ±0.2
HK 2125 8N2J-T RoHS 8.2 ±5％ 15 100 21 40 54 63 70 2400 3700 0.28 0.07 300 0.85 ±0.2
HK 2125 10NJ-T RoHS 10 ±5％ 15 100 20 38 51 60 67 2100 3100 0.30 0.09 300 0.85 ±0.2
HK 2125 12NJ-T RoHS 12 ±5％ 15 100 21 39 52 60 67 1900 3000 0.35 0.10 300 0.85 ±0.2
HK 2125 15NJ-T RoHS 15 ±5％ 15 100 22 42 55 63 72 1600 2600 0.40 0.11 300 0.85 ±0.2
HK 2125 18NJ-T RoHS 18 ±5％ 15 100 24 44 57 63 72 1500 2300 0.45 0.13 300 0.85 ±0.2
HK 2125 22NJ-T RoHS 22 ±5％ 18 100 23 43 55 60 69 1400 2100 0.50 0.16 300 0.85 ±0.2
HK 2125 27NJ-T RoHS 27 ±5％ 18 100 23 42 53 58 68 1300 1800 0.55 0.17 300 0.85 ±0.2
HK 2125 33NJ-T RoHS 33 ±5％ 18 100 24 43 54 55 60 1200 1700 0.60 0.19 300 0.85 ±0.2
HK 2125 39NJ-T RoHS 39 ±5％ 18 100 23 41 50 47 47 1000 1400 0.65 0.25 300 0.85 ±0.2
HK 2125 47NJ-T RoHS 47 ±5％ 18 100 23 41 49 43 41 900 1200 0.70 0.26 300 1.00 ＋0.2/－0.3
HK 2125 56NJ-T RoHS 56 ±5％ 18 100 23 42 48 39 38 800 1100 0.75 0.28 300 1.00 ＋0.2/－0.3
HK 2125 68NJ-T RoHS 68 ±5％ 18 100 25 42 45 30 － 700 900 0.80 0.33 300 1.00 ＋0.2/－0.3
HK 2125 82NJ-T RoHS 82 ±5％ 18 100 24 41 41 － － 600 800 0.90 0.37 300 1.00 ＋0.2/－0.3
HK 2125 R10J-T RoHS 100 ±5％ 18 100 23 37 37 － － 600 800 0.90 0.40 300 1.00 ＋0.2/－0.3
HK 2125 R12J-T RoHS 120 ±5％ 13 50 22 33 29 － － 500 700 0.95 0.43 300 1.00 ＋0.2/－0.3
HK 2125 R15J-T RoHS 150 ±5％ 13 50 22 34 26 － － 500 700 1.00 0.46 300 1.00 ＋0.2/－0.3
HK 2125 R18J-T RoHS 180 ±5％ 13 50 23 34 20 － － 400 600 1.10 0.50 300 1.00 ＋0.2/－0.3
HK 2125 R22J-T RoHS 220 ±5％ 12 50 20 23 － － － 350 550 1.20 0.75 300 1.00 ＋0.2/－0.3
HK 2125 R27J-T RoHS 270 ±5％ 12 50 20 29 － － － 300 480 1.30 0.85 300 1.00 ＋0.2/－0.3
HK 2125 R33J-T RoHS 330 ±5％ 12 50 22 15 － － － 250 400 1.40 0.90 300 1.00 ＋0.2/－0.3
HK 2125 R39J-T RoHS 390 ±5％ 10 50 17 12 － － － 250 400 1.30 0.85 300 1.00 ＋0.2/－0.3
HK 2125 R47J-T RoHS 470 ±5％ 10 50 17 － － － － 200 350 1.50 0.95 300 1.00 ＋0.2/－0.3
※ [] mark indicates the Inductance tolerance code. Please refer for the inductance tolerance except the above.

i_mlci_HK_e-E05R01

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .

19 101
 Multilayer chip inductors
Multilayer chip inductors for high frequency, Multilayer chip bead inductors
Multilayer common mode choke coils（MC series F type）
Metal Multilayer Chip Power Inductors (MCOILTM MC series)
■PACKAGING

①Minimum Quantity

●Tape & Reel Packaging

Thickness Standard Quantity ［pcs］
Type
mm（inch） Paper Tape Embossed Tape
CK1608（0603） 0.8 （0.031） 4000 －
0.85（0.033） 4000 －
CK2125（0805）
1.25（0.049） － 2000
0.85（0.033） 4000 －
CKS2125（0805）
1.25（0.049） － 2000
CKP1608（0603） 0.8 （0.031） 4000 －
CKP2012（0805） 0.9 （0.035） － 3000
CKP2016（0806） 0.9 （0.035） － 3000
0.7 （0.028） － 3000
CKP2520（1008） 0.9 （0.035） － 3000
1.1 （0.043） － 2000
LK1005（0402） 0.5 （0.020） 10000 －
LK1608（0603） 0.8 （0.031） 4000 －
0.85（0.033） 4000 －
LK2125（0805）
1.25（0.049） － 2000
HK0603（0201） 0.3 （0.012） 15000 －
HK1005（0402） 0.5 （0.020） 10000 －
HK1608（0603） 0.8 （0.031） 4000 －
0.85（0.033） － 4000
HK2125（0805）
1.0 （0.039） － 3000
HKQ0603W（0201） 0.3 （0.012） 15000 －
HKQ0603S（0201） 0.3 （0.012） 15000 －
HKQ0603U（0201） 0.3 （0.012） 15000 －
AQ105（0402） 0.5 （0.020） 10000 －
BK0603（0201） 0.3 （0.012） 15000 －
BK1005（0402） 0.5 （0.020） 10000 －
BKH0603（0201） 0.3 （0.012） 15000 －
BKH1005（0402） 0.5 （0.020） 10000 －
BK1608（0603） 0.8 （0.031） 4000 －
0.85（0.033） 4000 －
BK2125（0805）
1.25（0.049） － 2000
BK2010（0804） 0.45（0.018） 4000 －
BK3216（1206） 0.8 （0.031） － 4000
BKP0603（0201） 0.3 （0.012） 15000 －
BKP1005（0402） 0.5 （0.020） 10000 －
BKP1608（0603） 0.8 （0.031） 4000 －
BKP2125（0805） 0.85（0.033） 4000 －
MCF0605（0202） 0.3 （0.012） 15000 －
MCF0806（0302） 0.4 （0.016） － 10000
MCF1210（0504） 0.55（0.022） － 5000
MCF2010（0804） 0.45（0.018） － 4000
MCEE1005（0402） 0.55（0.022） 10000 －
MCFK1608（0603） 0.6 （0.024） 4000 －
MCFE1608（0603） 0.65（0.026） 4000 －
MCKK1608（0603） 1.0 （0.039） 3000
MCHK2012（0806） 0.8 （0.031） 4000 －
MCKK2012（0805） 1.0 （0.039） - 3000

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_pack_e-E07R01
 ②Taping material
●Card board carrier tape
Top tape CK 1608 BK 0603
CKP 1608 BK 1005
CK 2125 BK 1608
CKS 2125 BK 2125
LK 1005 BK 2010
LK 1608 BKP 0603
Base tape LK 2125 BKP 1005
HK 0603 BKP 1608
HK 1005 BKP 2125
Sprocket hole HK 1608 BKH 0603
HKQ 0603 BKH 1005
AQ 105 MCF 0605
Bottom tape MC 1005
Chip cavity
MC 1608
MC 2012
Chip Filled

Chip

●Embossed Tape
Top tape
CK 2125 BK 2125
CKS 2125 BK 3216
CKP 2012 MCF 0806
CKP 2016 MCF 1210
CKP 2520 MCF 2010
LK 2125 MC 1608
HK 2125 MC 2012

Sprocket hole

Base tape Chip cavity

Chip Filled

Chip

③Taping Dimensions
●Paper tape (8mm wide) Unit：mm（inch）
φ1.5＋0.1/－0 1.75±0.1
Sprocket hole (φ0.059＋0.004/-0) (0.069±0.004） T
(0.138±0.002)

(0.315±0.012)
3.5±0.05

A
8.0±0.3

F 4.0±0.1
(0.157±0.004)
2.0±0.05
(0.079±0.002)

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_pack_e-E07R01
 Thickness Chip cavity Insertion Pitch Tape Thickness
Type
mm（inch） Ａ Ｂ Ｆ Ｔ
1.0±0.2 1.8±0.2 4.0±0.1 1.1max
CK1608（0603） 0.8 （0.031）
（0.039±0.008） （0.071±0.008） （0.157±0.004） （0.043max）
1.5±0.2 2.3±0.2 4.0±0.1 1.1max
CK2125（0805） 0.85（0.033）
（0.059±0.008） （0.091±0.008） （0.157±0.004） （0.043max）
1.5±0.2 2.3±0.2 4.0±0.1 1.1max
CKS2125（0805） 0.85（0.033）
（0.059±0.008） （0.091±0.008） （0.157±0.004） （0.043max）
1.0±0.2 1.8±0.2 4.0±0.1 1.1max
CKP1608（0603） 0.8 （0.031）
（0.039±0.008） （0.071±0.008） （0.157±0.004） （0.043max）
0.65±0.1 1.15±0.1 2.0±0.05 0.8max
LK1005（0402） 0.5 （0.020）
（0.026±0.004） （0.045±0.004） （0.079±0.002） （0.031max）
1.0±0.2 1.8±0.2 4.0±0.1 1.1max
LK1608（0603） 0.8 （0.031）
（0.039±0.008） （0.071±0.008） （0.157±0.004） （0.043max）
1.5±0.2 2.3±0.2 4.0±0.1 1.1max
LK2125（0805） 0.85（0.033）
（0.059±0.008） （0.091±0.008） （0.157±0.004） （0.043max）
0.40±0.06 0.70±0.06 2.0±0.05 0.45max
HK0603（0201） 0.3 （0.012）
（0.016±0.002） （0.028±0.002） （0.079±0.002） （0.018max）
0.65±0.1 1.15±0.1 2.0±0.05 0.8max
HK1005（0402） 0.5 （0.020）
（0.026±0.004） （0.045±0.004） （0.079±0.002） （0.031max）
1.0±0.2 1.8±0.2 4.0±0.1 1.1max
HK1608（0603） 0.8 （0.031）
（0.039±0.008） （0.071±0.008） （0.157±0.004） （0.043max）
0.40±0.06 0.70±0.06 2.0±0.05 0.45max
HKQ0603W（0201） 0.3 （0.012）
（0.016±0.002） （0.028±0.002） （0.079±0.002） （0.018max）
0.40±0.06 0.70±0.06 2.0±0.05 0.45max
HKQ0603S（0201） 0.3 （0.012）
（0.016±0.002） （0.028±0.002） （0.079±0.002） （0.018max）
0.40±0.06 0.70±0.06 2.0±0.05 0.45max
HKQ0603U（0201） 0.3 （0.012）
（0.016±0.002） （0.028±0.002） （0.079±0.002） （0.018max）
0.75±0.1 1.15±0.1 2.0±0.05 0.8max
AQ105（0402） 0.5 （0.020）
（0.030±0.004） （0.045±0.004） （0.079±0.002） （0.031max）
0.40±0.06 0.70±0.06 2.0±0.05 0.45max
BK0603（0201） 0.3 （0.012）
（0.016±0.002） （0.028±0.002） （0.079±0.002） （0.018max）
0.65±0.1 1.15±0.1 2.0±0.05 0.8max
BK1005（0402） 0.5 （0.020）
（0.026±0.004） （0.045±0.004） （0.079±0.002） （0.031max）
1.0±0.2 1.8±0.2 4.0±0.1 1.1max
BK1608（0603） 0.8 （0.031）
（0.039±0.008） （0.071±0.008） （0.157±0.004） （0.043max）
1.5±0.2 2.3±0.2 4.0±0.1 1.1max
BK2125（0805） 0.85（0.033）
（0.059±0.008） （0.091±0.008） （0.157±0.004） （0.043max）
1.2±0.1 2.17±0.1 4.0±0.1 0.8max
BK2010（0804） 0.45（0.018）
（0.047±0.004） （0.085±0.004） （0.157±0.004） （0.031max）
0.40±0.06 0.70±0.06 2.0±0.05 0.45max
BKP0603（0201） 0.3 （0.012）
（0.016±0.002） （0.028±0.002） （0.079±0.002） （0.018max）
0.65±0.1 1.15±0.1 2.0±0.05 0.8max
BKP1005（0402） 0.5 （0.020）
（0.026±0.004） （0.045±0.004） （0.079±0.002） （0.031max）
1.0±0.2 1.8±0.2 4.0±0.1 1.1max
BKP1608（0603） 0.8 （0.031）
（0.039±0.008） （0.071±0.008） （0.157±0.004） （0.043max）
1.5±0.2 2.3±0.2 4.0±0.1 1.1max
BKP2125（0805） 0.85（0.033）
（0.059±0.008） （0.091±0.008） （0.157±0.004） （0.043max）
0.40±0.06 0.70±0.06 2.0±0.05 0.45max
BKH0603（0201） 0.3 （0.012）
（0.016±0.002） （0.028±0.002） （0.079±0.002） （0.018max）
0.65±0.1 1.15±0.1 2.0±0.05 0.8max
BKH1005（0402） 0.5 （0.020）
（0.026±0.004） （0.045±0.004） （0.079±0.002） （0.031max）
0.62±0.03 0.77±0.03 2.0±0.05 0.45max
MCF0605（0202） 0.3 （0.012）
（0.024±0.001） （0.030±0.001） （0.079±0.002） （0.018max）
1.1±0.05 1.9±0.05 4.0±0.1 0.72max
MCFK1608（0603） 0.6 （0.024）
（0.043±0.002） （0.075±0.002） （0.157±0.004） (0.028max)
0.8±0.05 1.3±0.05 2.0±0.05 0.6max
MCEE1005（0402） 0.55（0.021）
(0.031±0.002) (0.051±0.002) （0.079±0.002） (0.016max)
1.1±0.05 1.9±0.05 4.0±0.1 0.9max
MCFE1608（0603） 0.65（0.026）
（0.043±0.002） （0.075±0.002） （0.157±0.004） （0.035max）
1.55±0.2 2.3±0.2 4.0±0.1 0.9max
MCHK2012（0805） 0.8 （0.031）
（0.061±0.008） （0.091±0.008） （0.157±0.004） （0.035max）
Unit : mm（inch）

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_pack_e-E07R01
 ●Embossed Tape (8mm wide) Unit：mm（inch）
φ1.5＋0.1/－0 1.75±0.1
Sprocket hole (φ0.059＋0.004/-0) (0.069±0.004）

(0.138±0.002)

(0.315±0.012)
3.5±0.05
A

8.0±0.3
B

F 4.0±0.1
(0.157±0.004)
2.0±0.05
(0.079±0.002)

Thickness Chip cavity Insertion Pitch Tape Thickness

Type
mm（inch） Ａ Ｂ Ｆ K T
1.5±0.2 2.3±0.2 4.0±0.1 2.0 0.3
CK2125（0805） 1.25（0.049）
（0.059±0.008） （0.091±0.008） （0.157±0.004） （0.079） （0.012）
1.5±0.2 2.3±0.2 4.0±0.1 2.0 0.3
CKS2125（0805） 1.25（0.049）
（0.059±0.008） （0.091±0.008） （0.157±0.004） （0.079） （0.012）
1.55±0.2 2.3±0.2 4.0±0.1 1.3 0.3
CKP2012（0805） 0.9 （0.035）
（0.061±0.008） （0.091±0.008） （0.157±0.004） （0.051） （0.012）
1.8±0.1 2.2±0.1 4.0±0.1 1.3 0.25
CKP2016（0806） 0.9 （0.035）
（0.071±0.004） （0.087±0.004） （0.157±0.004） （0.051） （0.01）
1.4
0.7 （0.028）
（0.055）
1.4
0.9 （0.035）
2.3±0.1 2.8±0.1 4.0±0.1 （0.055） 0.3
CKP2520（1008）
（0.091±0.004） （0.110±0.004） （0.157±0.004） 1.7 （0.012）
1.1 （0.043）
（0.067）
1.7
1.1 （0.043）
（0.067）
1.5±0.2 2.3±0.2 4.0±0.1 2.0 0.3
LK2125（0805） 1.25（0.049）
（0.059±0.008） （0.091±0.008） （0.157±0.004） （0.079） （0.012）
1.5
0.85（0.033）
1.5±0.2 2.3±0.2 4.0±0.1 （0.059） 0.3
HK2125（0805）
（0.059±0.008） （0.091±0.008） （0.157±0.004） 2.0 （0.012）
1.0 （0.039）
（0.079）
1.5±0.2 2.3±0.2 4.0±0.1 2.0 0.3
BK2125（0805） 1.25（0.049）
（0.059±0.008） （0.091±0.008） （0.157±0.004） （0.079） （0.012）
1.9±0.1 3.5±0.1 4.0±0.1 1.4 0.3
BK3216（1206） 0.8 （0.031）
（0.075±0.004） （0.138±0.004） （0.157±0.004） （0.055） （0.012）
0.75±0.05 0.95±0.05 2.0±0.05 0.55 0.3
MCF0806（0302） 0.4 （0.016）
（0.030±0.002） （0.037±0.002） （0.079±0.002） （0.022） （0.012）
1.15±0.05 1.40±0.05 4.0±0.1 0.65 0.3
MCF1210（0504） 0.55（0.022）
（0.045±0.002） （0.055±0.002） （0.157±0.004） （0.026） （0.012）
1.1±0.1 2.3±0.1 4.0±0.1 0.85 0.3
MCF2010（0804） 0.45（0.018）
（0.043±0.004） （0.091±0.004） （0.157±0.004） （0.033） （0.012）
1.1±0.1 1.95±0.1 4.0±0.1 1.4 0.25
MCKK1608（0603） 1.0 （0.039）
（0.043±0.004） （±0.004） （0.157±0.004） （0.055） （0.01）
1.55±0.2 2.3±0.2 4.0±0.1 1.35 0.25
MCKK2012（0805） 1.0 （0.039）
（0.061±0.008） （0.091±0.008） （0.157±0.004） （0.053） （0.010）
Unit : mm（inch）

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_pack_e-E07R01
 ④LEADER AND BLANK PORTION
Blank portion Chip cavity Blank portion Leader

160mm or more 100mm or more

(6.3inches or more) (3.94inches or more)
400mm or more
Direction of tape feed (15.7inches or more)

⑤Reel Size

E t

B A
R D

W
A B C D E R
φ178±2.0 φ50 or more φ13.0±0.2 φ21.0±0.8 2.0±0.5 1.0

t W
4mm width tape 1.5max. 5±1.0
8mm width tape 2.5max. 10±1.5
(Unit : mm)
⑥Top tape strength
The top tape requires a peel-off force of 0.1～0.7N in the direction of the arrow as illustrated below.
Pull direction

0～15° Top tape

Base tape

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_pack_e-E07R01
 Multilayer chip inductors
Multilayer chip inductors for high frequency, Multilayer chip bead inductors
Multilayer common mode choke coils（MC series F type）
Metal Multilayer Chip Power Inductors (MCOILTM MC series)
■RELIABILITY DATA

1. Operating Temperature Range

BK series
－55～＋125℃
BKH series
BKP series －55～＋85℃
MCF series －40～＋85℃
CK series
CKS series
－40～＋85℃
Specified Value CKP series
LK series
HK0603, HK1005 －55～＋125℃
HK1608, HK2125 －40～＋85℃
HKQ0603
－55～＋125℃
AQ105
MCOILTM MC series －40～＋125℃（Including self-generated heat）

2. Storage Temperature Range

BK series
－55～＋125℃
BKH series
BKP series －55～＋85℃
MCF series －40～＋85℃
CK series
CKS series
－40～＋85℃
Specified Value CKP series
LK series
HK0603, HK1005 －55～＋125℃
HK1608, HK2125 －40～＋85℃
HKQ0603
－55～＋125℃
AQ105
MCOILTM MC series －40～＋85℃

3. Rated Current
BK series
The temperature of the element is increased within 20℃.
BKH series
BKP series The temperature of the element is increased within 40℃
MCF series Refer to each specification.
CK series
The temperature of the element is increased within 20℃.
CKS series
CKP series The temperature of the element is increased within 40℃
Specified Value
LK series The decreasing-rate of inductance value is within 5 %
HK0603, HK1005
HK1608, HK2125 The decreasing-rate of inductance value is within 5 %, or the temperature of the element is increased
HKQ0603 within 20℃
AQ105
Idc1: The decreasing-rate of inductance value is within 30 %
MCOILTM MC series
Idc2: The temperature of the element is increased within 40℃

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E07R01
 4. Impedance
BK series
BKH series
Specified Value Refer to each specification.
BKP series
MCF series
BK0603Series, BKP0603Series, BKH Series
Measuring frequency : 100±1MHz
Measuring equipment : 4991A（or its equivalent）
Measuring jig : 16193A（or its equivalent）
BK1005Series, BKP1005Series ,BKH1005Series
Measuring frequency : 100±1MHz
Measuring equipment : 4291A（or its equivalent）
Measuring jig : 16192A（or its equivalent）, HW:16193A（or its equivalent）
BK1608・2125Series, BKP1608・2125Series
Test Methods and
Measuring frequency : 100±1MHz
Remarks
Measuring equipment : 4291A（or its equivalent）, 4195A（or its equivalent）
Measuring jig : 16092A（or its equivalent）, HW:16192A（or its equivalent）
BK2010・3216Series
Measuring frequency : 100±1MHz
Measuring equipment : 4291A（or its equivalent）, 4195A（or its equivalent）
Measuring jig : 16192A（or its equivalent）
MCF Series
Measuring frequency : 100±1MHz
Measuring equipment : 4291A（or its equivalent）

5. Inductance
CK series
CKS series
CKP series
LK series
Specified Value HK0603, HK1005 Refer to each specification.
HK1608, HK2125
HKQ0603
AQ105
MCOILTM MC series
CK、CKS、LK Series
Measuring frequency : Refer to each specification.
Measuring equipment /jig : 1608,2125⇒4194A＋16085B＋16092A（or its equivalent）、4195A＋41951＋16092A（or its equivalent）
1005⇒4291A＋16193A（or its equivalent）
Measuring current : 047～4.7μH ⇒1mArms 、 5.6～33μH ⇒0.1mArms
CKP、MCOILTM MC Series
Measuring frequency : 1MHz
Measuring equipment : 4285A（or its equivalent）

Test Methods and HK0603、HK1005、AQ Series

Remarks Measuring frequency : 100MHz
Measuring equipment /jig : HK0603・AQ105⇒4291A＋16197A（or its equivalent）
HK1005⇒4291A＋16193A（or its equivalent）
HK1608、HK2125 Series
Measuring frequency : ～100nH⇒100MHz 、120nH～⇒50MHz
Measuring equipment /jig : 4195A＋16092A（or its equivalent）
HKQ Series
Measuring frequency : HKQ0603S・HKQ0603U⇒ 500MHz
Measuring frequency : HKQ0603W⇒ 300/500MHz
Measuring equipment /jig : E4991A＋16197A（or its equivalent）

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E07R01
 6. Q
CK series
CKS series －
CKP series
LK series
Specified Value HK0603, HK1005
HK1608, HK2125 Refer to each specification.
HKQ0603
AQ105
MCOILTM MC series －
LK Series
Measuring frequency : Refer to each specification.
Measuring equipment /jig : 1608,2125⇒4194A＋16085B＋16092A（or its equivalent）、4195A＋41951＋16092A（or its equivalent）
1005⇒4291A＋16193A（or its equivalent）
Measuring current : 047～4.7μH ⇒1mArms 、 5.6～33μH ⇒0.1mArms

HK0603、HK1005、AQ Series
Measuring frequency : 100MHz
Test Methods and
Measuring equipment /jig : HK0603・AQ105⇒4291A＋16197A（or its equivalent）
Remarks
HK1005⇒4291A＋16193A（or its equivalent）
HK1608、HK2125 Series
Measuring frequency : ～100nH⇒100MHz 、120nH～⇒50MHz
Measuring equipment /jig : 4195A＋16092A（or its equivalent）
HKQ Series
Measuring frequency : HKQ0603S・HKQ0603U⇒ 500MHz
Measuring frequency : HKQ0603W⇒ 300/500MHz
Measuring equipment /jig : E4991A＋16197A（or its equivalent）

7. DC Resistance
BK series
BKH series
BKP series
MCF series
CK series
CKS series
Specified Value CKP series Refer to each specification.
LK series
HK0603, HK1005
HK1608, HK2125
HKQ0603
AQ105
MCOILTM MC series
Test Methods and
Measuring equipment：VOAC-7412, VOAC-7512, VOAC-7521（made by Iwasaki Tsushinki）, HIOKI3227 (or its equivalent)
Remarks

8. Self Resonance Frequency（SRF）

BK series
BKH series
－
BKP series
MCF series
CK series
Refer to each specification.
CKS series
Specified Value CKP series －
LK series
HK0603, HK1005
HK1608, HK2125 Refer to each specification.
HKQ0603
AQ105
MCOILTM MC series －
LK、CK Series :
Measuring equipment : 4195A（or its equivalent）
Test Methods and
Measuring jig : 41951＋16092A（or its equivalent）
Remarks
HK、HKQ、AQ Series :
Measuring equipment : 8719C（or its equivalent）・8753D（or its equivalent）/HK2125

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E07R01
 9. Temperature Characteristic
BK series
BKH series
BKP series
MCF series
CK series
CKS series
CKP series －
LK series
HK0603, HK1005
Specified Value
HK1608, HK2125
HKQ0603
AQ105
MCOILTM MC series
HK0603, HK1005
HK1608, HK2125
Inductance change：Within ±10％
HKQ0603
AQ105
MCOILTM MC series Inductance change：Within ±15％
HK、HKQ、AQ Series：
Temperature range : －30～＋85℃
Test Methods and Reference temperature : ＋20℃
Remarks MCOILTM MC series：
Temperature range : －40～＋85℃
Reference temperature : ＋20℃

10. Resistance to Flexure of Substrate

BK series
BKH series
BKP series
MCF series
CK series
CKS series
Specified Value CKP series No mechanical damage.
LK series
HK0603, HK1005
HK1608, HK2125
HKQ0603
AQ105
MCOILTM MC series
Warp : 2mm（BK Series、BKP、BKH1005、CK、CKS、CKP、LK、HK、HKQ0603S、HKQ0603U、AQ Series、MCF1210、MC Series）
: 1mm（BKH0603、HKQ0603W、MCF Series without 1210 size,）
Testing board : glass epoxy-resin substrate
Thickness : 0.8mm
20

Test Methods and R-230

Remarks Board Warp

Deviation±1

45 45

（Unit：mm）

11. Solderability
BK series
BKH series
BKP series
MCF series
CK series
CKS series
Specified Value CKP series At least 90％ of terminal electrode is covered by new solder.
LK series
HK0603, HK1005
HK1608, HK2125
HKQ0603
AQ105
MCOILTM MC series
Solder temperature ：230±5℃ (JIS Z 3282 H60A or H63A)
Test Methods and
Solder temperature ：245±3℃ (Sn/3.0Ag/0.5Cu)
Remarks
Duration ：4±1 sec.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E07R01
 12. Resistance to Soldering
BK series
Appearance：No significant abnormality
BKH series
Impedance change：Within ±30％
BKP series
Appearance：No significant abnormality
MCF series
Impedance change：Within ±20％
Appearance：No significant abnormality
CK series
Inductance change： R10～4R7⇒Within ±10％、 6R8～100⇒Within ±15％
Appearance：No significant abnormality
CKS series
Inductance change：Within ±20％
Appearance：No significant abnormality
Specified Value CKP series
Inductance change：Within ±30％
Appearance：No significant abnormality
LK series Inductance change：1005⇒Within ±15％
1608,2125⇒ 47N～4R7: Within ±10％ 5R6～330: Within ±15％
HK0603, HK1005
HK1608, HK2125 Appearance：No significant abnormality
HKQ0603 Inductance change： Within ±5％
AQ105
Appearance：No significant abnormality
MCOILTM MC series
Inductance change： Within ±10％
Solder temperature ：260±5℃
Duration ：10±0.5 sec.
Test Methods and Preheating temperature ：150 to 180℃
Remarks Preheating time ：3 min.
Flux ：Immersion into methanol solution with colophony for 3 to 5 sec.
Recovery ：2 to 3 hrs of recovery under the standard condition after the test.（See Note 1）
(Note 1) When there are questions concerning measurement result；measurement shall be made after 48±2 hrs of recovery under the standard condition.

13. Thermal Shock

BK series
Appearance：No significant abnormality
BKH series
Impedance change： Within ±30％
BKP series
Appearance：No significant abnormality
MCF series
Impedance change： Within ±20％
CK series Appearance：No significant abnormality
CKS series Inductance change：Within ±20％
Appearance：No significant abnormality
CKP series
Specified Value Inductance change： Within ±30％
Appearance：No significant abnormality
LK series
Inductance change： Within ±10％ Q change： Within ±30％
HK0603, HK1005
HK1608, HK2125 Appearance：No significant abnormality
HKQ0603 Inductance change： Within ±10％ Q change： Within ±20％
AQ105
Appearance：No significant abnormality
MCOILTM MC series
Inductance change： Within ±10％
Conditions for 1 cycle
Step temperature（℃） time（min.）
1 Minimum operating temperature ＋0/－3 30±3
Test Methods and 2 Room temperature 2～3
Remarks 3 Maximum operating temperature ＋3/－0 30±3
4 Room temperature 2～3
Number of cycles：5
Recovery：2 to 3 hrs of recovery under the standard condition after the test.（See Note 1）
(Note 1) When there are questions concerning measurement result；measurement shall be made after 48±2 hrs of recovery under the standard condition.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E07R01
 14. Damp Heat（ Steady state）
BK series
Appearance：No significant abnormality
BKH series
Impedance change： Within ±30％
BKP series
Appearance：No significant abnormality
MCF series
Impedance change： Within ±20％
CK series Appearance：No significant abnormality
CKS series Inductance change： Within ±20％
Appearance：No significant abnormality
CKP series
Inductance change： Within ±30％
Specified Value
Appearance：No significant abnormality
LK series Inductance change： 1005,1608⇒Within ±10％ 2125⇒Within ±20％
Q change： Within ±30％
HK0603, HK1005
HK1608, HK2125 Appearance：No significant abnormality
HKQ0603 Inductance change： Within ±10％ Q change： Within ±20％
AQ105
Appearance：No significant abnormality
MCOILTM MC series
Inductance change： Within ±10％
BK、BKP、BKH、LK、CK、CKS、CKP、MCF Series：
Temperature ：40±2℃
Humidity ：90 to 95％RH
Duration ：500 +24/-0 hrs
Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1）
Test Methods and
Remarks
HK、HKQ、AQ、MCOILTM MC series：
Temperature ：60±2℃
Humidity ：90 to 95％RH
Duration ：500 +24/-0 hrs
Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1）
(Note 1) When there are questions concerning measurement result；measurement shall be made after 48±2 hrs of recovery under the standard condition.

15. Loading under Damp Heat

BK series
Appearance：No significant abnormality
BKH series
Impedance change： Within ±30％
BKP series
MCF series －
CK series Appearance：No significant abnormality
CKS series Inductance change： Within ±20％
Appearance：No significant abnormality
CKP series
Inductance change： Within ±30％
Appearance：No significant abnormality
Specified Value Inductance change： 1005⇒Within ±10％
LK series 1608⇒0.047～12.0μH： Within ±10％ 15.0～33.0μH： Within ±15％
2125⇒Within ±20％
Q change： Within ±30％
HK0603, HK1005
HK1608, HK2125 Appearance：No significant abnormality
HKQ0603 Inductance change： Within ±10％ Q change： Within ±20％
AQ105
Appearance：No significant abnormality
MCOILTM MC series※
Inductance change： Within ±10％
BK、BKP、BKH、LK、CK、CKS、CKP Series：
Temperature ：40±2℃
Humidity ：90 to 95％RH
Applied current ：Rated current
Duration ：500 +24/-0 hrs
Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1）
Test Methods and
Remarks
HK、HKQ、AQ、MCOILTM MC Series：
Temperature ：60±2℃
Humidity ：90 to 95％RH
Applied current ：Rated current ※MC series ; Idc2max
Duration ：500 +24/-0 hrs
Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1）
Note on standard condition: "standard condition" referred to herein is defined as follows:
5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure.
When there are questions concerning measurement results:
In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure.
Unless otherwise specified, all the tests are conducted under the "standard condition."
(Note 1) Measurement shall be made after 48±2 hrs of recovery under the standard condition.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E07R01
 16. Loading at High Temperature
BK series
Appearance：No significant abnormality
BKH series
Impedance change： Within ±30％
BKP series
Appearance：No significant abnormality
MCF series
Impedance change： Within ±20％
CK series Appearance：No significant abnormality
CKS series Inductance change： Within ±20％
Appearance：No significant abnormality
CKP series
Inductance change： Within ±30％
Appearance：No significant abnormality
Specified Value
Inductance change： 1005⇒Within ±10％
LK series 1608⇒0.047～12.0μH： Within ±10％ 15.0～33.0μH： Within ±15％
2125⇒Within ±20％
Q change： Within ±30％
HK0603, HK1005
HK1608, HK2125 Appearance：No significant abnormality
HKQ0603 Inductance change： Within ±10％ Q change： Within ±20％
AQ105
Appearance：No significant abnormality
MCOILTM MC series※
Inductance change： Within ±10％

Temperature : Maximum operating temperature

Test Methods and
Applied current ：Rated current ※MC series ; Idc2max
Remarks
Duration ：500 +24/-0 hrs
Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber. （See Note 1）

Note on standard condition: "standard condition" referred to herein is defined as follows:

5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure.
When there are questions concerning measurement results:
In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure. Unless
otherwise specified, all the tests are conducted under the "standard condition."
(Note 1) Measurement shall be made after 48±2 hrs of recovery under the standard condition.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_reli_e-E07R01
 Precautions on the use of Multilayer chip inductors
Multilayer chip inductors for high frequency, Multilayer chip bead inductors
Multilayer common mode choke coils（MC series F type）
■PRECAUTIONS

1. Circuit Design
◆Verification of operating environment, electrical rating and performance
1. A malfunction in medical equipment, spacecraft, nuclear reactors, etc. may cause serious harm to human life or have severe social
ramifications.
As such, any inductors to be used in such equipment may require higher safety and/or reliability considerations and should be clearly
Precautions
differentiated from components used in general purpose applications.
◆Operating Current（Verification of Rated current）
1. The operating current including inrush current for inductors must always be lower than their rated values.
2. Do not apply current in excess of the rated value because the inductance may be reduced due to the magnetic saturation effect.

2. PCB Design
◆Pattern configurations（Design of Land-patterns）
1. When inductors are mounted on a PCB, the size of land patterns and the amount of solder used（size of fillet）can directly affect inductor
performance.
Therefore, the following items must be carefully considered in the design of solder land patterns:
（1） The amount of solder applied can affect the ability of chips to withstand mechanical stresses which may lead to breaking or
cracking. Therefore, when designing land-patterns it is necessary to consider the appropriate size and configuration of the solder
pads which in turn determines the amount of solder necessary to form the fillets.
（2） When more than one part is jointly soldered onto the same land or pad, the pad must be designed so that each component's
Precautions
soldering point is separated by solder-resist.
（3） The larger size of land patterns and amount of solder, the smaller Q value after mounting on PCB. It makes higher the Q value to
design land patterns smaller than terminal electrode of chips.
◆Pattern configurations（Inductor layout on panelized［ breakaway］ PC boards）
1. After inductors have been mounted on the boards, chips can be subjected to mechanical stresses in subsequent manufacturing
processes （PCB cutting, board inspection, mounting of additional parts, assembly into the chassis, wave soldering the reflow soldered
boards etc.）For this reason, planning pattern configurations and the position of SMD inductors should be carefully performed to
minimize stress.
◆Pattern configurations（Design of Land-patterns）
1. The following diagrams and tables show some examples of recommended patterns to prevent excessive solder amounts（larger fillets
which extend above the component end terminations）. Examples of improper pattern designs are also shown.
（1） Recommended land dimensions for a typical chip inductor land patterns for PCBs
Land pattern
Chip inductor Solder-resist Chip inductor

C W

B A B L
Recommended land dimensions for wave-soldering （Unit：mm）
Type 1608 2012 2125 2016 2520 3216
L 1.6 2.0 2.0 2.0 2.5 3.2
Size
W 0.8 1.25 1.25 1.6 2.0 1.6
A 0.8～1.0 1.0～1.4 1.0～1.4 1.0～1.4 1.0～1.4 1.8～2.5
Technical
B 0.5～0.8 0.8～1.5 0.8～1.5 0.8～1.5 0.6～1.0 0.8～1.7
considerations
C 0.6～0.8 0.9～1.2 0.9～1.2 1.3～1.6 1.6～2.0 1.2～1.6

Recommended land dimensions for reflow-soldering （Unit：mm）

Type 0603 1005 105 1608 2012 2125 2016 2520 3216
L 0.6 1.0 1.0 1.6 2.0 2.0 2.0 2.5 3.2
Size
W 0.3 0.5 0.6 0.8 1.25 1.25 1.6 2.0 1.6
A 0.20～0.30 0.45～0.55 0.50～0.55 0.8～1.0 0.8～1.2 0.8～1.2 0.8～1.2 1.0～1.4 1.8～2.5
B 0.20～0.30 0.40～0.50 0.30～0.40 0.6～0.8 0.8～1.2 0.8～1.2 0.8～1.2 0.6～1.0 0.6～1.5
C 0.25～0.40 0.45～0.55 0.60～0.70 0.6～0.8 0.9～1.6 0.9～1.6 1.2～2.0 1.8～2.2 1.2～2.0

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_prec_e-E07R01
 Excess solder can affect the ability of chips to withstand mechanical stresses. Therefore, please take proper precautions when
designing land-patterns.
c d c Recommended land dimension for Reflow-soldering
Type 3216 2010 1210 0806 0605
L 3.2 2.0 1.25 0.85 0.65
Size
W 1.6 1.0 1.0 0.65 0.50

a
a
a 0.7～0.9 0.5～0.6 0.45～0.55 0.25～0.35 0.27～0.33
d b 0.8～1.0 0.5～0.6 0.7～0.8 0.25～0.35 0.17～0.23

b
b
c 0.4～0.5 0.2～0.3 0.25～0.35 0.25～0.35 0.20～0.26
d 0.8 0.5 0.55 0.5 0.4

a
a （Unit：mm）

（（2） Examples of good and bad solder application

Item Not recommended Recommended
Lead wire of component Solder-resist

Mixed mounting of SMD and

leaded components

Chassis
Solder (for grounding) Solder-resist
Component placement close to
the chassis

Electrode pattern
Lead wire of component
Soldering iron
Hand-soldering of leaded Solder-resist
components near mounted
components

Solder-resist

Horizontal component
placement

◆Pattern configurations（Inductor layout on panelized［ breakaway］ PC boards）

1-1. The following are examples of good and bad inductor layout; SMD inductors should be located to minimize any possible mechanical
stresses from board warp or deflection.
Item Not recommended Recommended
Position the component at a
right angle to the direction of
Deflection of the board
the mechanical stresses that
are anticipated.

1-2. To layout the inductors for the breakaway PC board, it should be noted that the amount of mechanical stresses given will vary
depending on inductor layout.
An example below should be counted for better design.

E
D

Perforation
C

A
B
Slit

Magnitude of stress A＞B＝C＞D＞E

1-3. When breaking PC boards along their perforations, the amount of mechanical stress on the inductors can vary according to the
method used. The following methods are listed in order from least stressful to most stressful: push-back, slit, V-grooving, and
perforation. Thus, any ideal SMD inductor layout must also consider the PCB splitting procedure.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_prec_e-E07R01
 3. Considerations for automatic placement
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the inductors when mounting onto the PC boards.
2. The maintenance and inspection of the mounter should be conducted periodically.
◆Selection of Adhesives
Precautions
1. Mounting inductors with adhesives in preliminary assembly, before the soldering stage, may lead to degraded inductor characteristics
unless the following factors are appropriately checked; the size of land patterns, type of adhesive, amount applied, hardening
temperature and hardening period. Therefore, it is imperative to consult the manufacturer of the adhesives on proper usage and
amounts of adhesive to use.
◆Adjustment of mounting machine
1. If the lower limit of the pick-up nozzle is low, too much force may be imposed on the inductors, causing damage. To avoid this, the
following points should be considered before lowering the pick-up nozzle:
（1） The lower limit of the pick-up nozzle should be adjusted to the surface level of the PC board after correcting for deflection of the
board.
（2） The pick-up pressure should be adjusted between 1 and 3N static loads.
（3） To reduce the amount of deflection of the board caused by impact of the pick-up nozzle, supporting pins or back-up pins should be
used under the PC board. The following diagrams show some typical examples of good pick-up nozzle placement:
Item Improper method Proper method

chipping
Single-sided mounting or cracking

supporting pins
or back-up pins

Double-sided mounting

chipping supporting pins

or cracking or back-up pins

Technical 2. As the alignment pin wears out, adjustment of the nozzle height can cause chipping or cracking of the inductors because of mechanical
considerations impact on the inductors. To avoid this, the monitoring of the width between the alignment pin in the stopped position, and maintenance,
inspection and replacement of the pin should be conducted periodically.
◆Selection of Adhesives
1. Some adhesives may cause reduced insulation resistance. The difference between the shrinkage percentage of the adhesive and that of
the inductors may result in stresses on the inductors and lead to cracking. Moreover, too little or too much adhesive applied to the
board may adversely affect component placement, so the following precautions should be noted in the application of adhesives.
（1） Required adhesive characteristics
a. The adhesive should be strong enough to hold parts on the board during the mounting & solder process.
b. The adhesive should have sufficient strength at high temperatures.
c. The adhesive should have good coating and thickness consistency.
d. The adhesive should be used during its prescribed shelf life.
e. The adhesive should harden rapidly.
f. The adhesive must not be contaminated.
g. The adhesive should have excellent insulation characteristics.
h. The adhesive should not be toxic and have no emission of toxic gasses.
（2） When using adhesives to mount inductors on a PCB, inappropriate amounts of adhesive on the board may adversely affect
component placement. Too little adhesive may cause the inductors to fall off the board during the solder process. Too much
adhesive may cause defective soldering due excessive flow of adhesive on to the land or solder pad.
［Recommended conditions］ Amount of adhesives After inductors are bonded
Figure 0805 case sizes as examples a a

a 0.3mm min
b
b 100～120μm
c Area with no adhesive
c c

4. Soldering
◆Selection of Flux
1. Since flux may have a significant effect on the performance of inductors, it is necessary to verify the following conditions prior to use;
（1） Flux used should be with less than or equal to 0.1 wt% （Chlorine conversion method） of halogenated content. Flux having a strong
acidity content should not be applied.
Precautions （2） When soldering inductors on the board, the amount of flux applied should be controlled at the optimum level.
（3） When using water-soluble flux, special care should be taken to properly clean the boards.
◆Soldering
1. Temperature, time, amount of solder, etc. are specified in accordance with the following recommended conditions, and please contact us
about peak temperature when you use lead-free paste.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_prec_e-E07R01
 ◆Selection of Flux
1-1. When too much halogenated substance（Chlorine, etc.）content is used to activate the flux, or highly acidic flux is used, an excessive
amount of residue after soldering may lead to corrosion of the terminal electrodes or degradation of insulation resistance on the
surface of the Inductor.
1-2. Flux is used to increase solderability in flow soldering, but if too much is applied, a large amount of flux gas may be emitted and may
detrimentally affect solderability. To minimize the amount of flux applied, it is recommended to use a flux-bubbling system.
1-3. Since the residue of water-soluble flux is easily dissolved by water content in the air, the residue on the surface of Inductor in high
humidity conditions may cause a degradation of insulation resistance and therefore affect the reliability of the components. The
cleaning methods and the capability of the machines used should also be considered carefully when selecting water-soluble flux.
◆Soldering
1-1. Preheating when soldering
Heating: Chip inductor components should be preheated to within 100 to 130℃ of the soldering. Cooling: The temperature difference
between the components and cleaning process should not be greater than 100℃.
Chip inductors are susceptible to thermal shock when exposed to rapid or concentrated heating or rapid cooling. Therefore, the
soldering process must be conducted with a great care so as to prevent malfunction of the components due to excessive thermal
shock.

［Reflow soldering］
【Recommended conditions for eutectic soldering】 【Recommended condition for Pb-free soldering】
300 300
Preheating 230℃ Peak
Within 10sec. 260℃ Max.
60sec. 60sec Within 10sec.

Temperature（℃）
Temperature（℃）

200 Min. Min. 200

Slow
Slow cooling
cooling

100 100

Preheating150℃ Heating above

60sec. Min. 230℃
40sec. Max.
0 0
※Ceramic chip components should be preheated to within 100 to 130℃ of the
soldering.
※Assured to be reflow soldering for 2 times.
※ MC series; Peak 230 ℃ (eutectic soldering) 、 260 ℃ (Pb-free soldering)max
within 5sec.
Caution
1. The ideal condition is to have solder mass（fillet）controlled to 1/2 to 1/3 of the thickness of the inductor, as shown
below:
1/2T～1/3T
Inductor
Technical Solder T
considerations
PC board
2. Because excessive dwell times can detrimentally affect solderability, soldering duration should be kept as close to
recommended times as possible.
［Wave soldering］
【Recommended conditions for eutectic soldering】 【Recommended condition for Pb-free soldering】
300 300
230～250℃ Peak
Preheating Within 3sec. 260℃ Max.
120sec. Min. Within 10sec.
120sec. Min.
Temperature（℃）

Temperature（℃）

200 200
Slow cooling Slow
Preheating cooling
100 150℃
100

0 0
※Ceramic chip components should be preheated to within 100 to 130℃ of the
soldering.
※Assured to be wave soldering for 1 time.
※Except for reflow soldering type.
Caution
1. Make sure the inductors are preheated sufficiently.
2. The temperature difference between the inductor and melted solder should not be greater than 100 to 130℃.
3. Cooling after soldering should be as gradual as possible.
4. Wave soldering must not be applied to the inductors designated as for reflow soldering only.
［Hand soldering］
【Recommended conditions for eutectic soldering 【Recommended condition for Pb-free soldering】
400 400
Peak
230～280℃
Within 3sec. 350℃ Max.
Within 3sec.
300 300
⊿T
Temperature（℃）
Temperature（℃）

Slow cooling
200 200
Slow cooling
Preheating
100 150℃ Min.
100
Preheating
60sec. Min. 60sec. Min.
0 0
（※⊿Ｔ≦190℃（ 3216Type max）, ⊿Ｔ≦130℃（ 3225 Type min）
※It is recommended to use 20W soldering iron and the tip is 1φor less.
※The soldering iron should not directly touch the components.
※Assured to be soldering iron for 1 time.
Note: The above profiles are the maximum allowable soldering condition, therefore
these profiles are not always recommended.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_prec_e-E07R01
 Caution
1. Use a 20W soldering iron with a maximum tip diameter of 1.0 mm.
2. The soldering iron should not directly touch the inductor.

5. Cleaning
◆Cleaning conditions
1. When cleaning the PC board after the Inductors are all mounted, select the appropriate cleaning solution according to the type of flux
Precautions used and purpose of the cleaning（e.g. to remove soldering flux or other materials from the production process.）
2. Cleaning conditions should be determined after verifying, through a test run, that the cleaning process does not affect the inductor's
characteristics.
◆Cleaning conditions
1. The use of inappropriate solutions can cause foreign substances such as flux residue to adhere to the inductor, resulting in a degradation
of the inductor's electrical properties（especially insulation resistance）.
2. Inappropriate cleaning conditions（insufficient or excessive cleaning）may detrimentally affect the performance of the inductors.
（1） Excessive cleaning
Technical
a. In the case of ultrasonic cleaning, too much power output can cause excessive vibration of the PC board which may lead to the
considerations
cracking of the inductor or the soldered portion, or decrease the terminal electrodes' strength. Thus the following conditions
should be carefully checked;
Ultrasonic output Below 20W/ℓ
Ultrasonic frequency Below 40kHz
Ultrasonic washing period 5 min. or less

6. Post cleaning processes

◆Application of resin coatings, moldings, etc. to the PCB and components.
1. With some type of resins a decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while
left under normal storage conditions resulting in the deterioration of the inductor's performance.
Precautions 2. When a resin's hardening temperature is higher than the inductor's operating temperature, the stresses generated by the excess heat
may lead to inductor damage or destruction.
3. Stress caused by a resin's temperature generated expansion and contraction may damage inductors.
The use of such resins, molding materials etc. is not recommended.

7. Handling
◆Breakaway PC boards（splitting along perforations）
1. When splitting the PC board after mounting inductors and other components, care is required so as not to give any stresses of deflection
or twisting to the board.
2. Board separation should not be done manually, but by using the appropriate devices.
◆General handling precautions
1. Always wear static control bands to protect against ESD.
2. Keep the inductors away from all magnets and magnetic objects.
3. Use non-magnetic tweezers when handling inductors.
Precautions
4. Any devices used with the inductors（ soldering irons, measuring instruments） should be properly grounded.
5. Keep bare hands and metal products（i.e., metal desk）away from chip electrodes or conductive areas that lead to chip electrodes.
6. Keep inductors away from items that generate magnetic fields such as speakers or coils.
◆Mechanical considerations
1. Be careful not to subject the inductors to excessive mechanical shocks.
（1） If inductors are dropped on the floor or a hard surface they should not be used.
（2） When handling the mounted boards, be careful that the mounted components do not come in contact with or bump against other
boards or components.

8. Storage conditions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packaging material in good condition, care must be taken to control
temperature and humidity in the storage area. Humidity should especially be kept as low as possible.
・Recommended conditions
Precautions
Ambient temperature: Below 30℃ Humidity: Below 70% RH
The ambient temperature must be kept below 40℃. Even under ideal storage conditions, solderability of inductor is deteriorated as time
passes, so inductors should be used within 6 months from the time of delivery.
・Inductor should be kept where no chlorine or sulfur exists in the air.
◆Storage
Technical 1. If the parts are stocked in a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of
considerations terminal electrodes and deterioration of taping/packaging materials may take place. For this reason, components should be used within
6 months from the time of delivery. If exceeding the above period, please check solderability before using the inductors.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_prec_e-E07R01