Scribd
Upload
39 views10 pages

Introduction

This document discusses the basic tools used for engineering graphics and drawings. It describes 8 common drawing instruments: drawing sheets and papers, a mini drafter for parallel and perpendicular lines, set squares for angles, a protractor for measuring angles, compasses for circles, dividers for transferring lengths, pencils and lead pens for drawing, a pencil sharpener, and erasers. The accurate use of these tools is important for conveying design ideas through technical drawings.

Uploaded by

Subba Reddy Vanukuri
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
39 views10 pages

Introduction

This document discusses the basic tools used for engineering graphics and drawings. It describes 8 common drawing instruments: drawing sheets and papers, a mini drafter for parallel and perpendicular lines, set squares for angles, a protractor for measuring angles, compasses for circles, dividers for transferring lengths, pencils and lead pens for drawing, a pencil sharpener, and erasers. The accurate use of these tools is important for conveying design ideas through technical drawings.

Uploaded by

Subba Reddy Vanukuri
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

MEC 103

ENGINEERING GRAPHICS
INTRODUCTION

The role of engineers is to design & develop the products. In their business,
engineers have to prepare drawings to convey their ideas. The graphical language
used by engineers is called as Engineering Drawing. Just as a picture speaks
thousands of words, a complete technical drawing tells everything about the
geometry of the product.

RAHUL SHARMA
17-08-2017
16932
DRAWING INSTRUMENTS

1. Drawing Sheets and Papers:


Drawing sheets and papers are the ‘canvases’ on which drawings are composed by pencils
or pens. Drawing sheets are available in standard sizes. Indian Standards (IS) for drawing
sheets and drawing boards as recommended by the Bureau of Indian Standards (BIS) are
shown in Table.

17-08-2017 RAHUL SHARMA 16932


2. Mini Drafter:
A mini drafter is a portable device used to draw parallel, inclined and perpendicular lines
speedily. It is mounted on a drawing board at the top left corner. A drafter consists of a
scale, a scale screw, a scale plate, steel bars, a bar plate and a clamping mechanism.

17-08-2017 RAHUL SHARMA 16932


3.Set-squares:
Two set squares—(i) 45° set-square and (ii) 30°– 60° set-square, are the most common
drawing instruments.

17-08-2017 RAHUL SHARMA 16932


4. Protractor :
Protractor is used to draw and measure the angles. It is available separately or as merged
in 45° set-square.

17-08-2017 RAHUL SHARMA 16932


5. Compasses :
Compasses are used to draw circles or arcs. Two sizes of compasses—(i) large compass
and (ii) small spring bow compass are in common use. A large compass consists of a
needle leg and a pencil leg hinged together at upper ends, Fig. 1.7(a). The two legs carry,
respectively, a needle point and a pencil point at their lower ends. The pencil point can be
interchanged with a pen point, Fig. 1.7(b). Lengthening bar, Fig. 1.7(c), is used to draw
circles of diameter greater than 150 mm. Small spring bow compasses are of two types:
bow pencil compass.

17-08-2017 RAHUL SHARMA 16932


6. Dividers :
Dividers are used to transfer lengths from one place to other. They are also used to set-
off desired distance from the scale on the paper.

17-08-2017 RAHUL SHARMA 16932


7. Pencils/Lead Pens :
The quality of drawing largely depends on the selection and use of proper grade of pencil.
The grade of a pencil is printed near its blocked end. For technical drawing, three grades
of pencils, namely, H, 2H and HB are recommended. A lead pen, Fig. 1.10, is an
alternative to the pencil.

17-08-2017 RAHUL SHARMA 16932


8. Pencil Sharpener :
A pencil sharpener is a device used to mend the pencils. It conveniently
removes the wooden shell covering the lead. A common hand-held
sharpener, Fig. 1.12(a), is recommended.

9. Eraser :
A non-dusting good quality eraser is recommended for erasing
unwanted part of the pencil drawing.

17-08-2017 RAHUL SHARMA 16932

You might also like