LNG Gas Quality PDF

EUROPEAN COMMISSION
DG MOVE
SEVENTH FRAMEWORK PROGRAMME
GC.SST.2012.2-3 GA No. 321592
Gas Quality
LNG Blue Corridors Project is supported by the European Commission under the Seventh Framework
Programme (FP7). The sole responsibility for the content of this document lies with the authors. It does
not necessarily reflect the opinion of the European Union. Neither the FP7 nor the European
Commission is responsible for any use that may be made of the information contained therein.
Deliverable No. LNG BC D3.2

Deliverable Title Gas quality
Dissemination level Public
Written By Staffan Johannesson (SGA) 03/01/2014
Checked by Milagros Rey (GNF) 06/01/2014
Approved by Xavier Ribas (IDIADA) 06/01/2014
Issue date 06/12/2013 Revision 2. Updated : 17/03/2014
LNG BC D3.2 Gas quality Public
Revision History
Author Organization Description

Milagros Rey Porto GNF January 2014. Suggested additional content
Judith Domínguez IDIADA February 2014. Suggested additional content
Xavier Ribas IDIADA March 2014. Suggested additional content
2/48
Executive Summary
The LNG Blue Corridor project is focused on demonstrating the use of LNG as truck fuel and to define
a road map for future large scale development of the market. This report is the second deliverable of
the Work Package 3.
Work Package 3 LNG Logistics which includes aspects to supply the market with fuel filling stations
and up-stream. The report covers aspects of LNG and LBG.
LNG is a dynamic, cryogenic fuel which means that specific considerations must be taken to secure fuel
properties from terminal up to the time of delivery to the truck.
This report – 3.2 Gas Quality - is written to highlight the aspects of gas quality for LNG and LBG to be
used as fuel in trucks. Additional reports regarding gas quality issues will be written based on
experiences gained as the project develops. Examples of future deliverables with relevance to this
report are D3.6 Liquefied Biomethane experiences and D3.11 Studies regarding ageing of fuel.
Discussions on how to find marked- and technology solutions to handle varying gas qualities should
be done in the initial phase of the project covering the following topics (examples):
• Sourcing of gas
• Fuel management solutions throughout the delivery chain.
• Solutions to secure gas quality are kept within agreed specification.
• Measuring of gas quality in small scale LNG facilities
• Evaluation regarding design criteria and possibilities for different engine technologies to be
optimized toward different gas qualities in terms of robustness, engine efficiency and emission
control. The project consortium is recommended to monitor and report accordingly during the
demonstration period, at what extent gas quality will effectively influence engine performance,
setting through substantiated observations the range of quality indicators and parameters
jointly with target range values to be met to ensure proper functioning of engines
3/48
Contents
Executive Summary ................................................................................................................................. 3
1 Introduction..................................................................................................................................... 6
1.1 LNG Blue Corridors project ...................................................................................................... 6
1.2 Aim of this deliverable............................................................................................................. 7
2 Gas quality – Compressed vs. Liquefied .......................................................................................... 8
2.1 Differences between CNG and LNG ........................................................................................ 8
2.2 LNG specifications ................................................................................................................... 9
2.2.1 Methane number .......................................................................................................... 10
2.2.2 LNG saturation............................................................................................................... 11
2.2.3 Wathering of LNG fuel ................................................................................................... 14
2.3 LNG fuel quality standarization ............................................................................................. 15
3 LNG delivery chain ......................................................................................................................... 18
4 Gas quality by market: source, import and export ....................................................................... 20
4.1 Import of LNG ........................................................................................................................ 21
4.1.1 Asia ................................................................................................................................ 21
4.1.2 Western Europe............................................................................................................. 22
4.1.3 America.......................................................................................................................... 22
4.2 Differences between the markets ......................................................................................... 22
4.3 Gas Quality Management ...................................................................................................... 23
4.3.1 Ballasting ....................................................................................................................... 24
4.3.2 Propane/butane removal/injection .............................................................................. 24
4.3.3 Carbon dioxide or nitrogen removal ............................................................................. 24
4.3.4 Blending ......................................................................................................................... 24
4.4 Interchangeability.................................................................................................................. 25
4.4.1 Country Gas Quality Programmes ................................................................................. 25
4.4.2 Interchangeability parameters ...................................................................................... 26
5 Sensitivity to varying gas quality ................................................................................................... 31
5.1 Methane number .................................................................................................................. 33
5.1.1 Methane number calculation ........................................................................................ 34
5.2 Impact of Gas Characteristics on the Dual Fuel Operation – engines derating .................... 36
4/48
5.2.1 Knocking ........................................................................................................................ 36

5.2.2 Misfiring......................................................................................................................... 37
5.3 Silloxanes ............................................................................................................................... 38
5.4 Hydrogen ............................................................................................................................... 41
6 Measuring gas quality................................................................................................................... 42
7 Conclusions.................................................................................................................................... 43
8 Recommendations for the LNG-BC project ................................................................................... 45
9 Glossary ......................................................................................................................................... 46
List of Tables ...................................................................................................................................... 47
List of figures ..................................................................................................................................... 47
5/48
1 Introduction
1.1 LNG Blue Corridors project
The LNG Blue Corridors project’s aim is to establish LNG as a real alternative for medium- and long-
distance transport—first as a complementary fuel and later as an adequate substitute for diesel. Up to
now the common use of gas as fuel has been for heavy vehicles running on natural gas (NG) only for
municipal use, such as urban buses and garbage collection trucks. In both types of application, engine
performance and autonomy are good with present technologies, as they are well adapted to this
alternative cleaner fuel.
However, analyzing the consumption data, the equivalence in autonomy of 1 liter of diesel oil is 5 liters
of CNG (Compressed Natural Gas), compressed to 200 bar. Five times more volume of fuel prevents
the use of CNG in heavy road transport, because its volume and weight would be too great for a long-
distance truck. This opens the way for LNG (Liquefied Natural Gas), which is the way natural gas is
transported by ship to any point of the globe. NG liquefies at 162º C below zero, and the cost in
energy is only 5% of the original gas. This state of NG gives LNG the advantage of very high energy
content. Only 1,8 liters of LNG are needed to meet the equivalent autonomy of using 1 liter of diesel
oil. A 40-ton road tractor in Europe needs a tank of 400 to 500 liters for a 1.000 km trip; its equivalent
volume with liquid gas would be 700 to 900 liters of LNG, a tank dimension that could easily be fitted
to the side of the truck chassis. LNG therefore opens the way to the use of NG for medium- and long-
distance road transport.
LNG has huge potential for contributing to achieving Europe’s policy objectives, such as the
Commission’s targets for greenhouse gas reduction, air quality targets, while at the same time
reducing dependency on crude oil and guaranteeing supply security. Natural gas heavy-duty vehicles
already comply with Euro V emission standards and have enormous potential to reach future Euro VI
emission standards, some without complex exhaust gas after-treatment technologies, which have
increased procurement and maintenance costs.
To meet the objectives, a series of LNG refueling points have been defined
along the four corridors covering the Atlantic area (green line), the
Mediterranean region (red line) and connecting Europe’s South with the
North (blue line) and its West and East (yellow line) accordingly. In order to
implement a sustainable transport network for Europe, the project has set
the goal to build approximately 14 new LNG stations, both permanent and
mobile, on critical locations along the Blue Corridors whilst building up a
fleet of approximately 100 Heavy-Duty Vehicles powered by LNG.
Figure 1-1. Impression of the

This European project is financed by the Seventh Framework Programme
LNG Blue Corridors (FP7), with the amount of 7.96 M€ (total investments amounting to 14.33
M€), involving 27 partners from 11 countries.
nd
This document corresponds to the 2 deliverable within work package 3. It is a document describing
the aspects of gas quality for LNG and LBG to be used as fuel in trucks. This document will be available
at the project website: http://www.lngbluecorridors.eu/.
6/48
1.2 Aim of this deliverable

The LNG Blue Corridor project is focused on demonstrating the use of LNG as truck fuel and to define
a road map for future large scale development of the market. This report is written as part of the Work
Package 3 LNG Logistics which includes aspects to supply the market with fuel filling stations and up-
stream. The report covers aspects of LNG and LBG.
LNG is a dynamic, cryogenic fuel which means that specific considerations must be taken to secure fuel
properties from terminal up to the time of delivery to the truck.
This report – 3.2 Gas Quality - is written to highlight the aspects of gas quality for LNG and LBG to be
used as fuel in trucks. Additional reports regarding gas quality issues will be written based on
experiences gained as the project develops.
7/48
2 Gas quality – Compressed vs. Liquefied

When describing the issues of gas quality for liquefied gas there are significant aspects to handle in
terms of pressure/temperature and how to store the liquefied gas up to it is delivered from the
refueling station to the truck and how it is handled at the truck. However, except from fuel pressure to
the engine there are from an engine design perspective no significant difference between compressed
or liquefied as the gas during combustion always is injected in gaseous form. Therefore, gas quality
aspects for LNG and LBG is mainly focused on how to secure same quality level as compressed gas
with additional parameters due to liquefaction.
2.1 Differences between CNG and LNG

The use of the natural gas means a reduction of the contaminants in the combustion process, in
addition, the natural gas liquefaccion process have a particular advantage in terms of storage and
transport. This is the one of the differences in the use of LNG as a fuel of Heavy duty vehicles. But in
order to know better the difference between CNG and LNG about the gas quality below are detailed
the composition of the both gases and some differences that affect to the gas quality.CNG is different
from LNG in that it is a gas that is compressed to nominal pressures as high as 3,600 pounds per
square inch (psi). (Pressures can be even higher when taking temperature compensation effects into
account.).
LNG has a higher energy density than CNG and many other alternative fuels. This means that LNG has
most energy per volume than CNG.
It is also important talk about the LCNG (Liquefied to compressed natural gas), it is produced by
pumping LNG up to a selected pressure level and then vaporizing the liquid through a heat exchanger
(vaporizer). It is more efficient and faster to pressurize natural gas in liquid form. LCNG can be
pressurized via a relatively small cryogenic pump (e.g., basketball size). LCNG can be used for light-
and heavyduty vehicles and its fueling stations and operations are similar to those for LNG.1
The liquefaction process, of the LNG; requires the removal of the non-methane components like
carbon dioxide, water, butane, pentane and heavier components from the produced natural gas. When
vaporized it burns only in concentrations of 5% to 15% when mixed with air. For this reason, and
others which are explained in the following chapters of this deliverable, CNG and LNG varies in
composition. In this way are explained some differences between CNG and LNG, which we discuss this
further in following chapters.
1
Resource Guide for Heavy-Duty LNG Vehicles, Infrastructure, and Support Operations, march 2002, Brookhaven National
Laboratory and Gas Technology Institute
8/48
Figure 2-1. Composition CNG and LNG
2.2 LNG specifications 3
Per definition LNG is natural gas which has been cooled down so much that it is converted into a
liquid. The base natural gas from which it is made not only contains methane, although this is by far
the most abundant component, but also ethane, propane and even some butane, and, a contain
amount of, nitrogen will be present as well.
Since, after nitrogen, the methane requires the lowest temperature for liquefaction, the other
hydrocarbons, which may present in the natural gas, will all become liquids before the methane during
the cooling-down process. Therefore, the standard situation is to take out most of these in a process
called fractioning and which can be explained by the boiling temperatures and liquid densities.
Table 2-1 Boilin temperatures and densities – LNG Componenets
Boiling temperature at Liquid density (kg/dm3)

atmospheric pressure (ºC)
Nitrogen -195.8 0.810
Methane -161.5 0.421
Ethane -88.6 0.546
Propane -42.0 0.585
N-Butane -0.5 0.600
Depending on the liquefaction process, storage capacity, other practical and economical
considerations at the terminal, there might be an incentive to keep some of the higher hydrocarbons
in the LNG.
2
http://www.beg.utexas.edu/energyecon/lng/LNG_introduction_07.php
3
http://www.gie.eu/ “GIE position paper on gas quality”
9/48
A limited amount of heavy hydrocarbons will always be present in the LNG, but the actual content may
depend on its origin. This also means that there will be a certain spread in the knocking resistance
(methane number) of gas made from LNG depending on its origin. As we will see in the following
chapter: Gas quality by source market.
Liquefaction plans have strict requirements on gas purity to prevent freeze out (carbon dioxide-CO2,
water and heavy hydrocarbons), corrosion and erosion. Some components must be removed to meet
the LNG product specifications, ashydrogen Sulfide-H2S, corrosive and erosion components (mercury),
inert components (helium and nitrogen) and oil. Consequently, LNG contains no CO2 and no corrosive
substances. Anyways the composition is still variable.
1. During the LNG transportation the "Boil off" appears, and this affects the LNG composition
(gas quality). These differences in the LNG composition show up in the engines
operation:Natural boil-off gas, which is taken of the top of the LNG tanks above the liquid will
have a high methane content and some nitrogen and thus have a high knocking resistance.
Analysis show values typically around Methane Number (MN) 100 and LCV between 33-35
MJ/Nm3. (Initial gas extraction after up-loading may have reduced calorific value because of
the high nitrogen content at the top of the tanks). This is a somewhat special application
typical for fuelling of LNG tanker propulsion plants.
2. Forced boil-off gas, i.e. LNG extracted from down in the tanks and evaporated separately. This
gas will contain a mixture of all hydrocarbons in the liquid and its resistance to knocking may
differ from origin to origin and even from load to load, with the MN typically in the range
between 70 and 80. The calorific value will be higher than natural boil-off gas and quite stable
at around 38-39 MJ/Nm3.4
2.2.1 Methane number

The motor octane number and the methane number are topics of interest on describing a fuel for use
in an engine. These numbers describe the tendency for a fuel to knock (early or pre-ignition) in a
spark-ignited engine.
The motor octane number is most familiar on ratings used for gasoline and the methane number has
been developed to better describe knock tendency of gaseous fuels. "The methane number scale is
based on the molar percents of methane and hydrogen, with neat methane equal to 100 methane
number.”5
The selection of a limit to methane number is very important because if the range to methane number
is between 80 and 100 this would exclude the majority of available LNG from coming to Europe. Below
you can see a figure that visualizes the methane number versus Wobbe index for LNG qualities.
Recently, there has been a push to reduce the methane content requirement for LNG to one that is
more similar to the CNG so that more suppliers can be used in transportation. But currently, most LNG
4
http://www.cimac.com/cimac_cms/uploads/explorer/Working%20groups/CIMAC_WG17_LNG_position_v7_
rev.pdf
5
Southwest Research Institute, Effects of Gas Composition on Engine Performance and Emissions, GRI-91/0054,
1991.
10/48
vehicle users require very high methane content (>98%). This higher methane content for LNG is
intended to reduce the effects of weathering of the fuel.
Figure 2-2. Methane number versus Wobbe index of importers LNG
The lower methane content can also lower the price of the LNG. Your LNG supplier can provide the
methane number for LNG fuel that they can supply. Note that the lower the methane content, the
more vigilant the users will need to be in understanding weathering of LNG and minimizing the effect.
LNG weathering is discussed in more detail later in this subsection.7
The topic of the methane number is explained in further details in the Chapter 6 "Sensitivity to varying
gas quality".
2.2.2 LNG saturation

Unlike gases, which increase in density under higher pressures, saturated liquid-vapor mixtures are less
dense at higher pressures. Understanding saturation is critical to assess the use of LNG and the
amount of LNG stored on a vehicle or in a storage tank.
6
http://www.iea-amf.org/content/fuel_information/methane
7
http://www.afdc.energy.gov/pdfs/lng_resource_guide.pdf
11/48
LNG is stored on-board a vehicle as a saturated liquid-vapour mixture. This means that the mixture is
in between the liquid and vapour phases, so it will boil when heat is added and condense when heat is
removed.
To understand LNG saturation, it is helpful to briefly consider the process of refrigerating natural gas
to make LNG. As heat is removed from the gas, its temperature decreases. This continues until the
gas becomes so cold that it begins to condense to a liquid. The temperature and pressure at which
this occurs is called the saturation point. Both the gas (which is usually referred to as a vapour in this
state) and the liquid that starts to form are said to be saturated. At this point, removing heat will cause
more vapour to condense to liquid, but will not reduce the temperature as long as the pressure is held
constant and the natural gas is not completely condensed, or liquefied. The temperature at which this
transition from vapour to liquid takes place is called the saturation temperature. In commercially
available LNG fuel systems, fuel is stored on-board vehicles under saturated conditions, because it
reaches an equilibrium of liquid and vapour through boiling and condensation. As stated earlier, a
saturated liquid-vapour mixture typically boils when heat is added and condenses when heat is
removed.
The saturation temperature for condensation or boiling depends on the pressure. Conversely, the
saturation pressure for boiling or condensation depends on the temperature. The relation between
saturation temperature and saturation pressure is shown in Figure 2-3. This is known as the saturation
curve or saturation line.
Figure 2-3 the saturation curve for natural gas (100% methane), defines the conditions where the liquid and vapour phases can
coexist (ºF=1.8 ºC+32 and 1psi=6.90 kPa)
12/48
Figure 2-3 applies if the natural gas (and LNG) is 100% methane. When natural gas contains other
constituents, the saturation temperature (or pressure) changes slightly as more vapor is condensed to
liquid, or liquid is boiled to vapor. Also, the concentration of non-methane constituents is different in
the liquid and vapor phases. If the non-methane constituents have a higher boiling temperature than
methane, they may be more concentrated in the liquid phase. This phenomenon is called “weathering”
or “enrichment” in some situations. When natural gas is saturated, the liquid phase usually has a
much higher density than the vapor phase. The dependence of this density on the pressure and
temperature is indicated in Figures 2-4 and 2-5, by the difference in density between the triangle to
the far right of the figures and the circle to the left of the figures. It should be noted that these points
lie on the broken-line curves labeled “saturation line.”
In Figures 2-4 and 2-5, the triangles to the right denote the state of the liquid in the LNG fuel tank,
which is assumed to be saturated at a typical pressure of 100 psig (690 kPa). The corresponding
saturation temperature is -200° F (-93° C). Note that the liquid density at this state is 23.0 lbm/ft3
(368 kg/m), which is nearly twice the density of a full CNG fuel tank. The higher density of LNG relative
to CNG is the main reason that LNG is preferred for many heavyduty vehicles with high fuel
consumption and limited space for fuel tanks. On the other hand, CNG is more convenient for light-
duty vehicles and many medium-duty vehicles, because fueling is simpler and there are no issues
associated with cryogenic materials, fuel vaporization, and venting. The circles on the left side of
Figures 2-4 and 2-5 denote the state of the vapor in the LNG fuel tank ullage, which is saturated at the
same temperature and pressure as the liquid.
Figure 2-4 pressure-density conditions of LNG fuel systems
13/48
Figure 2-5 Temperature-density conditions of LNG fuel systems
The path shown from the triangle to the circle to the diamond in Figures 2-4 and 2-5 denotes the
change experienced by the LNG as it is warms in the vaporizer. Its temperature and pressure remain
constant at saturation conditions until all the liquid is boiled to vapor. As more heat is added in the
“vaporizer,” the gas temperature increases (Figure 4-5), and the density decreases slightly. Figures 2-2
and 2-4 illustrate an additional issue pertaining to LNG fuel system design. Note that if the LNG could
be stored at a lower saturation temperature and pressure, its density would be greater and so more
fuel could be stored in a given-size fuel tank. However, for currentgeneration LNG fuel systems, it is
convenient to store LNG at a saturation pressure slightly more than the engine fuel pressure
requirement. This simplifies the system because no fuel pump is required, but it also involves
compromises including the quantity of fuel that can be contained in the fuel tank.
2.2.3 Wathering of LNG fuel8

The Dedicated natural gas engines are typically designed for a minimum methane content in the fuel.
When the LNG is stored for long periods, there is a tendency for the lighter gases (specifically
methane) to boil off and vent, leaving the heavier components. Consequently, the methane content of
fuel that is stored for long periods of time can diminish. This process is known as weathering
8
http://www.afdc.energy.gov/pdfs/lng_resource_guide.pdf
14/48
This fuel, with the reduction of the methane, can cause reduced engine performance and even engine
failure when used on a vehicle. In order to reduce weathering, LNG fuel should be treated as a
perishable product.
Proper fleet management is crucial to preventing excessive weathering. The best weapon against
weathering is to prevent the fuel being stored long enough for significant boil off. By using the
vehicles regularly, the pressure within the fuel containers stays at reasonable levels, preventing
excessive vaporization of the fuel within the container, thus preventing weathering. Any techniques
that prevent heat gains will also prevent weathering, as well as fuel venting. This is true of both the
vehicle fuel system as well as the fueling station. By using the fuel stored on the vehicle and in on-site
fuel storage tanks in a timely manner, heat gains are prevented which will reduce both weathering and
loss of fuel through venting.
The susceptibility of a vehicle fuel system to weathering will depend on how the fuel system is
designed to remove fuel from the fuel tanks. Some systems are designed to remove vapor from the
fuel tank before removing liquid. These systems are highly susceptible to weathering because the
vapor removed from the tank will be mostly methane. Higher hydrocarbons will become concentrated
in the liquid that remains in the fuel tank. As the tank approaches empty, the methane content of the
fuel delivered to the engine will decrease. If the tank is not emptied before each refueling, the
methane content of the fuel in the tank will progressively decrease with each refueling. Another
system design removes primarily liquid fuel from the fuel tank. While this system will not prevent all
weathering, it will prevent progressive weathering of fuel from successive fuelings. With a liquid draw
fuel system, there should not be significant on-board weathering issues as long as the vehicles are
used regularly. Understanding how the vehicle fuel system used on your vehicles removes fuel from
the fuel tanks will help you to properly manage your fleet to prevent excessive weathering. For these
same reasons, it is important for you to understand how vapor is managed in stationary fuel storage
tanks as well.
2.3 LNG fuel quality standarization

There are ongoing projects within the standardization organization CEN to handle gas quality aspects
with focus on compressed gas. Traditionally standardization of gas has been strongly focused on
safety aspects but not so much on engine design aspects drivability, efficiency, etc9. Gas infrastructure
is dealt with within CEN/TC 234, in which WG 11 is handling the functional requirements of gas quality.
For petroleum products the vehicle fuel quality aspects are normally handled by TC019. These two
groups have commonly formed the PC408 with main focus to define the quality aspects of biomethane
for injection and use as vehicle fuel which is also relevant for the use of natural gas as vehicle fuel. A
general position is that TC 234 Gas Infrastructure is focusing to preserve present status while the
actors within TC019 is working for tight specification of gas quality with reference to fulfillment of
emission lever EURO 6 and fuel efficiency.
The only present international standard for CNG is “ISO 15403:2006 Natural gas for use as a
compressed fuel for vehicles”. In this standard no limits are given in the normative part 1 (Designation
9
Source: Mattias Svensson, Swedish Gas technology Center, Presentation at NGV 2013 Gothenburg,
15/48
of the quality). However, part 2 includes an informative technical report (Specification of the quality) on
certain trace elements which to a high degree is based on US national standard SAE J1616 from 1994.
Criteria handled in ISO15403:2006 are:
Table 2-2 Parameters in ISO 15403:2006
Parameter Level Unit
CO2 < 0.03 Volume fraction

O2 < 0.03 Volume fraction
S < 120 mg/m3
H2S < 5mg S/m3
Mercaptans < 15mg S/m3
Water < 30 mg/m3
Also the European Association for the Streamlining of Energy Exchange – gas, EASEE-gas, has
identified a number of gas properties and parameters for harmonization across the European Union.
Based on specific reference conditions the parameters are described in the table below. 3
Table 2-3 EASEE gas specification
Another standard dealing with qualitative criteria is Swedish Standard SS 155438:1999. This standard
covers the scope of direct utilization of biomethane as vehicle fuel. The standard is under revision and
will be updated during spring 2014. Examples of covered parameters in present standard for
biomethane to vehicles with catalyst (Type B) are:
Table 2-4 Examples of aspects covered in biomethane standard SS 15 54 38 10.
Wobbe index lower: 43,9 – 47 MJ/m3

Metan content: 97+/- 2 %
MON 130
Dew point t-5
10
Standard can be required from http://www.sis.se/en/petroleum-and-related-technologies/fuels/gaseous-
fuels/ss-155438
16/48
Water content max. 32 mg/m3

CO2+O2+N2 max. 5 % (vol) where of O2 max 1 % (vol)
Total sulphur max 23 mg/m3
The aspects of harmonization and standardization of LNG will be developed during the project and
reported in later deliverables, e.g. D3.5 and D3.11
The LNG Blue Corridor-project will increase the experiences from using methane as vehicle fuel and
will develop knowledge that will support the development of the standards especially with additional
data regarding experiences of liquefied gas. As the work to develop the standards is ongoing all
aspects regarding specific quantitative with relevance also to compressed gas is referred to TC234 and
PC408. In the LNG Blue Corridor project it is recommended to harmonize the actors view of which are
the important parameters that are to be considered as important design critera for future efficient and
clean technologies and possibilities to provide the gas to the market on a cost efficient level for all
actors within the market chain. This is primary recommended to be done in working groups with open
dialogue including open dialogue regarding LNG-engine systems and fuel logistics/upgrading aspects
with actors participating in WP2 and WP3.
17/48
3 LNG delivery chain

LNG is commonly used globally to supply the market with natural gas. The supply chain is traditionally
based on large scale production of LNG by condensation of natural gas close to the gas field. The gas
is stored in a LNG export terminal built for export from which large deep sea LNG carriers transport
LNG to import terminals. Japan and South Korea are countries importing LNG. Also in Europe LNG is
imported though terminals in Portugal, Spain, UK, Belgium, the Netherlands, Italy, etc. The absolute
majority of the imported LNG is re-gasified and injected to the European gas grid and distributed in
gaseous form to end-customers for heat and power generation.
By using LNG as truck fuel the delivery chain is added with more steps as this requires small scale LNG
delivery to the refueling station. For LBG the distribution chain involves different steps and the chain as
a whole is to consider as small scale compared to LNG distribution chain, see illustration below.
Figure 3-1 Generic description of different distribution chains for LNG and LBG
Liquefied natural gas is stored and transported in tanks as a cryogenic liquid, i.e. as a liquid at a
temperature below its boiling point. Just like any liquid, LNG evaporates at temperatures above its
boiling point and generates Boil-off gas (BOG). BOG is caused by the heat ingress into the LNG during
storage, shipping and loading/unloading operations. The amount of BOG depends on the design and
operating conditions of LNG tanks and ships.The increase in BOG increases the pressure in the LNG
tank. In order to maintain the tank pressure within the safe range, BOG should be continuously
eliminated. In the LNG supply chain, BOG can be used as fuel, re-liquefied or burned in a gasification
18/48
plant. Furthermore, the more volatile components (nitrogen and methane) boil-off first, changing LNG
composition and quality over time.11
The US and European markets have to some extent developed differently with respect to gas quality,
with the US being the leanest one. One of the reasons for this is the use of LNG peak shaving facilities
for seasonal swing, and the fact that the domestic sources have been leaner in the US, than the
supplies from the north, east and south to Europe. In Europe large pipelines along with underground
storage has been used to meet the peak demand.
11
http://hrcak.srce.hr/ “Problem of Boil-off in LNG Supply Chain”
19/48
4 Gas quality by market: source, import and

export
Due to the liquefaction of methane the fuel is to a large extent already upgraded. This means in theory
less variations in gas quality compared to markets offering different qualities of compressed gas, i.e. L-
GAS vs. H-GAS or different levels of upgraded biogas. However, the content of LNG from different
sources still varies depending on the source and this is important to take notice of when designing
engines.
Table 4-1 Worldwide average LNG compositions
Source; NGVA Europe Position Paper: LNG, a Sustainable Fuel for all Transport Modes
The table above is an example based on average composition per source. The qualities defined in the
tables might change over time. Other variations of gas might occur if the cryogenic fuel is stored too
long in the storage tank or in the fuel tanks of the vehicle. Small scale mixing of LNG qualities, i.e.
refueling of storage tanks at filling stations will also lead to small variation in gas quality delivered to
the truck.
Information about LBG gas quality have been found from Lidköping Biogas (Sweden) and Gasrec (UK)
which are the two leading actors in EU producing LBG. Depending on the producer the qualities are as
presented in table below:
Table 4-2 LBG gas quality in UK and Sweden
Parameter Lidköping Biogas (SE) Gasrec (UK) Unit

Methane 98,5 97 % Vol.
Nitrogen 1,2 3 % Vol.
Oxygen 0,3 - % Vol.
Energy content 13,5 N/D kWh/kg
20/48
The LBG produced by Gasrec is physically blended into LNG and sold as “bio-LNG” with a standard
blend of 25% LBG. The LBG in Sweden is typically sold by the fuel distribution company FordonsGas
under the name of “BiGreen” which means the LBG is normally sold without blending but with carbon
footprint based on 50% renewable content. This system is certified by the third party “Svanen”12 which
is a Nordic Eco Labelling organization.
4.1 Import of LNG
The performance and consumption of the vehicle depends directly on the gas quality. We saw that the
gas characteristic differs in accordance with the market. LNG coming from two different sources will
have high variation on the principal gas key parameters. Variations of Methane Number, Wobbe Index
or Heating value will affect the customer buy changing the engines performance or even affect the
engine reliability (Knocking, Misfire ). For this reason, a gas harmonization is needed in order to avoid
performance disparities due to a different source of importation.
13
Figure 4-1 worldwide overseas LNG importation
Imports represent three key markets: Asia, Western Europe and America14.
4.1.1 Asia
Five importing countries: Japan (as the world’s leading importer, Japan purchases 39% of global
production), South Korea (15.2% of imports), Taiwan (5%), India (4.6%) and China.
12
Svanen’s criteria for third party certification of vehicle fuel is found here.
13
www.gie.eu (20130606 GLE presentation, LNG Shipping Forum, by Pierre Cotin)
14
Source: http://www.elengy.com/en/the-market-of-lng/globaçl-market-trends/three-key-markets.html
21/48
Since 2006, these countries have imported LNG from seven producer countries: Qatar (the world’s
leading exporter, with 17% of global production), Malaysia (13.1%), Indonesia (12%), Australia (8.7%),
Brunei (4.1%), Oman (5.4%) and Abu Dhabi (3.3%).
In 2007, Asian countries also imported LNG produced in Alaska, Egypt, Algeria, Nigeria and Equatorial
Guinea (plant commissioned in 2007).
4.1.2 Western Europe

Most trade in LNG is from Algeria (10.4% of global production), Nigeria (9.7%) and Egypt (6.2%). This
LNG goes to Spain (11% of global imports), France (5.6%), Turkey, Belgium, Italy, Portugal, the United
Kingdom and Greece.
In 2007, cargoes also came from Qatar, Trinidad-and-Tobago, Libya and, to a lesser degree, Oman.
The first two deliveries were also received from the Snøhvit plant in Norway, which came on stream in
2007.
4.1.3 America
The USA is both an exporter—shipping LNG to Japan from Alaska (0.6%)—and an importer (9.5% of
the world total), receiving LNG on the East Coast and in the Gulf of Mexico, mainly from Trinidad-and-
Tobago (8.3%), Egypt and Nigeria, as well as from Equatorial Guinea.
Porto-Rico, the Dominican Republic and Mexico (since 2006) also import LNG.
4.2 Differences between the markets

The three most important markets are supplied with different LNG composition.
The Asian market (Mostly Japan) is oriented to the Rich LNG due to its historically originated LNG
supplies from Indonesia, Malaysia, Brunei, Australia, and Abu Dhabi (i.e. mostly sourced from rich gas
fields). So Japanese specifications typically require LNG with a higher Heating Value and Wobbe Index
that is than the gas which can be produced. In these cases, the imported LNG needs to be enriched
with LPG. Korea follows the same pattern as Japan standard quality without LPG addition.
The American market represented by the USA, which uses mostly lean LNG coming from Alaska
production plants. The range of acceptable Heating Values varies between pipelines, but is lower than
that of most LNG that is currently available. Exceptions to this are LNG from Trinidad, Egypt, Equatorial
Guinea and some Algerian LNG; historically most of the LNG imports to the USA have come from these
countries.
The various European gas quality specifications are different but broadly similar. Three groups of
natural gases have been defined by EN 437 which specifies the test gases and pressures to be used
when testing domestic gas appliances for compliance with the Gas Appliance Directive. These
categories are defined according to their Wobbe Index as follows:
• Group L: 39.1 < W < 44.8 MJ/m3

• Group H: 45.7 < W < 54.7 MJ/m3
• Group E: 40.9 < W < 54.7 MJ/m3
22/48
Group L and H refer to low-calorific value and high calorific value gases available in countries in the
Continental Europe. Specifically defined and used only in Germany and Luxembourg, Group E covers
all of the Wobbe Index range of Group H and part of that of Group L. Each EU country has then
defined their own limits within these categories for their different gas transmission systems. The
Netherlands, UK and Italy are likely to need to process the import LNG to the national specifications.
Table 4-3 International Comparision of Wobbe Index Ranges
USA White Paper3 ± 4.0% Wobbe
UK GS(M)R ± 4.3% Wobbe
EASEE-gas Proposed CBP Gas Quality ± 5.6% Wobbe
France Transmission Entry Spec. ± 7.0% Wobbe
Germany National Standards ± 10.1% Wobbe
Italy National Standards ± 5.0% Wobbe
Korea National Standards ± 4.6% Wobbe
New Zealand National Standards ± 6.1% Wobbe
UAE Abu Dhabi Spec. ± 3.0% Wobbe
The European LNG imported has strong differences on their composition which results on Wobbe
index and Heating values disparities. As show in the table 5-1, the Wobbe index ranges changes form a
country to another (example UK ± 4.3% / Germany ± 10.1% Wobbe Index) . These fluctuations affect every
stages of the LNG supply chain, from the import production plant to the customer. In order to keep
the same vehicle performance, the LNG available through Europe should meet standards in order to
obtain a constant LNG quality.
4.3 Gas Quality Management 15
Quality adjustment of gas or liquefied natural gas (LNG) can be carried out at various stages in the
chain of natural gas production and use, to meet contractual specifications.
Techniques listed below are widely used for quality adjustment at point of production, as well as at
import terminal prior to send-out point, with the exception of blending which is mainly carried out in
the transmission network:
• Ballasting with inert gas.

• Propane/butane removal/injection.
• Carbon dioxide or nitrogen removal.
• Blending of different streams.
15
www.igu.org/gas-knowhow/publications/igu-publications/Gas%20Interchangeability%202011%20v6%20HighRes.pdf
23/48
Control of combustion process (air-to-fuel ratio) is often preferred at the point of use to cope with the
variation in gas quality
4.3.1 Ballasting
Ballasting is a technique to lower the Wobbe Index and Heating Value of rich natural gas by the
addition of a readily available gas (e.g. nitrogen, carbon dioxide, air, hydrogen) such that the quality of
send-out gas from a terminal meets customer requirements. The degree of adjustment is often limited
by the allowable concentration of a specific component.
• Ballasting with nitrogen is widely used for its strong effect on Wobbe Index.
• Air ballasting is very similar to nitrogen ballasting albeit with the disadvantage of introducing
oxygen into the natural gas.
• High levels of hydrogen induce high flame speed and high diffusivity; therefore, hydrogen
ballasting is limited to small changes.
4.3.2 Propane/butane removal/injection

Propane/butane removal or injection will allow modifying the gas original Wobbe index to Rich or
Lean levels in order to meet the expect specifications.
LPG and NGL removal from LNG are standard fractionation processes, except that the operating
temperatures involved for LNG are substantially lower than most other fractionation processes. For rich
feed gas streams, it is standard practice for the LNG plant to remove NGLs (LPGs and/or condensate).
LPG (in both its liquid and gasified forms) can be injected into a natural gas or LNG stream to increase
its Wobbe Index. One major issue with LPG injection is the increased hydrocarbon dewpoint which
could result in condensation into local distribution systems after pressure letdown. Therefore, this is
only practical for small corrections.
4.3.3 Carbon dioxide or nitrogen removal

Carbon dioxide removal is only applicable to pipeline gas as LNG contains no carbon dioxide. Removal
could be based on amine absorption, solid bed adsorption or membrane separation. It is economical
and efficient for small adjustment of Wobbe Index. The process of nitrogen removal by cryogenic
distillation is more complex, as it requires upstream elimination of carbon dioxide and water which
have lower boiling points. This technique is used to adjust gas quality which is beyond the capacity of
carbon dioxide removal.
Since LNG has virtually zero carbon dioxide content, the carbon dioxide or nitrogen removal method is
only applicable for adjustment of pipeline gas quality prior to entry into a transmission system.
4.3.4 Blending
Blending is typically a low cost option and can be used for both derichment and enrichment
depending on the quality of the blending gas available. At an LNG export/import terminal, blending of
LNG between tanks in its cryogenic liquid form can be done for quality management. This is a routine
operation for many import terminals receiving LNG from diverse suppliers and where storage is
limited.
24/48
Another upstream adjustment option is blending of LNG in the send out section prior to entering
transmission pipeline, to eliminate the need for an extra blending tank. Blending in the network deals
with transient changes of gas quality and is not always possible
For LNG, in-tank blending is likely to be the cheapest option provided no additional storage tank is
required and stratification problems can be avoided.
4.4 Interchangeability 16
Interchangeability: “The ability to substitute one gaseous fuel for another in a combustion application
without materially changing operational safety, efficiency, performance or materially increasing air
.
pollutant emissions“17 .
This topic is a relevant issue to talk about the differences qualities of LNG in the market. The issue of
the LNG interchangeability is therefore how to ensure security of gas supply at reasonable cost,
knowing that gas quality parameters of much imported gas may be at the extremes of, or outside,
existing gas-specification limits.
Below you can see the major categories of gas quality and their objectives for best interchangeability.
Some of these topics already have been discussed before, in order to talk about the composition and
its characteristics of the LNG.
Energy content Gross Calorific Value Billing

Energy load Wobbe Index Burner control
Combustion characteristics European Standards EN 437 Health & Safety
Impurities S compounds, O2, CO2, water & Damage avoidance
HC dew points
4.4.1 Country Gas Quality Programmes

Different countries have come to describe their interchangeability issues in a number of different ways.
This section gives several examples and describes the national/regional initiatives developed to
achieve harmonised gas quality standards.
• UK Gas Quality Programme – The completed test programme led by the UK government,
leading to the recent decision on the UK strategy for dealing with new gas imports.
• Europe Follows UK Programme – The development of EASEE-gas standard for cross-border
trading across EU member states, and work by CEN, the European Standardisation
Department.
• United States – The recognition of Wobbe Index and initiatives to converge towards
harmonised standards through the National Gas Council.
16
MVV consultant “Study on Interoperability of LNG Facilities and Interchangeability of Gas and Advice on
the Opportunity to Set-up an Action Plan for the Promotion of LNG Chain Investments”
17
A useful definition of interchangeability could be the one provided by the NGC+ group
25/48
• Far East – The Far East occupies a unique position in gas quality standardisation, with Japan
being a mature LNG based market and Korea and China as emerging gas users. Their
respective efforts in gas quality standardisation are discussed.
18
Figure 4-2 Development of gas quality specifications
4.4.2 Interchangeability parameters19

The most critical measure to interchangeability is the Wobbe Index. Below we show the range of
variation of this parameter by LNG source.
18
www.gie.eu (20130606 GLE presentation, LNG Shipping Forum, by Pierre Cotin)
19
ec.europa.eu "Fjrc_reference_report_200907_liquefied_natural_gas.pdf"
26/48
Different interchangeability measures have been specified by countries.
• In the Continental Europe, limitations on Wobbe Index and inert gases are considered to be
sufficient for wholesale gas.
• The UK looked further into parameters related to appliance non-optimum performance such
as the Lift Index, Incomplete Combustion Factor and Soot Index.
In the report “Liquefied Natural Gas for Europe - Some Important Issues for Consideration”20 discuss
this topic, the two illustrations folowing are taken from this report.
Figure 4-3 Composition of European pipeline gas and LNG (the relative size of the bubbles indicates the methane content); Source
Report EUR 23818 EN
Figure 4-4 Physical properties of European pipeline gas and LNG (the relativesize of bubbles indicates the density of gas relative to
air) Report EUR 23818 EN
20
The report EUR 23818 EN is found here
27/48
Figure 4-5 Typical Wobbe index for LNG source
In the figure above shows average Wobbe Index for most sources of LNG supply to Europe.
How you can see the average values from all selected sources are within the limits of Wobbe index
calues that EASEE-gas recommended for the gas to be accepted at all entry and interconnection point
in the European Union.
Figure 4-6 Wobbe number requirements at EU LNG import terminals
In the figure above shows the maximum and minimum Wobbe Index values set by the seven importers
of LNG into Europe. These values are also compared to EASEE-gas recommendation.
This parameter is not a completely accurate way to predict the behavior of burners using alternate
gases, but it is convenient and accurate enough for most purposes. Generally speaking, a gas in the
preferred ranges of HHV and Wobbe Index will burn without combustion problems such as flame
28/48
lifting, flashback, excessive NOx and CO, or yellow tipping. Figure below shows the preferred Wobbe
Index region and the consequences of operating in objectionable ranges.
Figure 4-7 Wobbe Index region and the consequences of operating in objectionable ranges
Early LNG trade was primarily to Japan from Pacific Rim and Middle East export plants and to Europe
from Northern Africa. The Japanese specifications vary depending on the importing utility company,
but typically have a high heating value between 39.7 and 43.3 MJ/Sm. This relatively high range
permits maximum use of infrastructure by moving greater combustion heat capacity for a given
volume. European countries typically allow wider ranges. Spain, for example, allows a range between
35.0 and 44.9 MJ/Sm.
In one example a gas with HHV = 42.6 MJ/Sm3 is suitable for the Japanese and Korean markets, but is
too high for the US or UK. In the second example a gas with HHV = 37.2 MJ/Sm3 meets US/UK specs
but has an HHV too low for Korea or Japan. Both examples however are within the ranges allowed for
France and Spain.
Figure 4-8 Worlwide heating value specifications
29/48
For base load LNG production the feed gas pre-treatment will be similar for a wide range of feeds.
CO2, water and mercury will have to be removed completely (to 50 ppm CO2 and 1 ppm water). This is
generally done in the same way for all base load LNG plants around the world.
N2 is always reduced to a level below the limit for roll over, generally 1 mol%. During design, the 1%
limit is normally used, but in operation this can be somewhat increased, since rollover is a minor
problem for the upstream production due to the short storage time. Setting the Gross Calorific Value
(GCV) for the LNG is an issue for the process engineer when doing the design. The pressure and
temperature in the heavy hydrocarbon (HHC) column will decide the split between the part going to
cool down, and the rest going to fractionation. How this is integrated in the liquefaction process will
depend both on the design philosophy and on the technology used, but this is in general straight
forward for all of the available LNG technologies.
New and stricter environmental regulations will affect the design for LNG liquefaction plant.
Traditionally, all technologies have used end flash as fuel gas, along with boil off gas (BOG) from the
storage tanks. Normally the BOG is returned from the ships during loading has been flared. This design
has generally been independent of LNG liquefaction technology.21
21
http://www.igu.org/html/wgc2009/papers/docs/wgcFinal00118.pdf
http://www.environment.gov.au/archive/settlements/transport/comparison/
30/48
5 Sensitivity to varying gas quality

The truck engines are based on different technologies. Depending on the technology the engine is
more or less sensitive to different fuel qualities or specific parameters. The engine technologies have
different critical design criteria and can be optimized for a larger or smaller window. Typically, dual-
fuel technology is more sensitive to varying gas qualities compared to spark ignited engines in terms
of knocking. However, also spark ignited engines are optimized based on specific gas properties. An
example is Methane Number [MN] as design criteria. Methane Number is a way to calculate the fuel
sensitivity for knocking and is calculated based on the content of the fuel. The higher value the more
resistant the fuel is to knocking thereby allowing increased engine compression ratio in a spark ignited
engine or higher diesel substitution factor in a dual-fuel engine. A spark ignited engine can use gas
with low Methane Number, but the higher value that is possible to optimize the engine towards, the
higher efficiency the spark ignited engine can reach as this will give possibility to increase compression
ratio etc. Minimum methane number for a spark ignited EURO 6 engine is MN7022 while there are
examples that specific technology platforms of dual-fuel engines for EURO 5 require at least MN85 or
even MN90 to be able to optimize the efficiency of the engine.
EURO 6 and the stricter regulation increases the need to either develop technologies with high
possibility to adapt to different gas qualities or to use gas with less varying quality, thereby making the
engine fulfillment of EURO 6 technically less advanced. From an engine development perspective gas
as fuel is still to be considered as a new type of fuel for trucks compared to diesel. From a gas provider
point of view the vehicle market is still small compared to heat and electricity. In combination with
competition between different technology providers willing to support the truck OEM it has until know
been difficult to openly evaluate relevant design criteria that influence efficiency and robustness for
different technology platforms. The experience of gas engine demonstration for EURO 6 for truck
OEMs and technology providers within LNG-BC will be the platform for conclusion of relevant design
criteria to quantify how gas quality affects the efficiency and costs to fulfill EURO 6.
A parameter that has been discussed for biomethane and LBG, especially when produced from landfill
is potential contamination by siloxanes. Based on studies in Sweden23 the conclusion is that the
amount of siloxanes in the raw gas is taken care of during the upgrading of the gas. Therefore,
siloxanes should not be considered as a show-stopper but as a parameter to keep a close eye upon
during the upgrading of biogas to biomethane where the key factor is that the filtering systems are
running properly at all times.
Based on input from engine manufacturers developing EURO 6 engines the LNG-BC project has to
report more quantitative figures for the relevant parameters when the data is available and processed
by the actors in the project.
As we have seen the chapter of gas quality in function on how LNG is extracted there are two distinct
type of gas, Natural boil-off and Forced boil-off, in the following paragraphs is explained how affect
these difference in fuel to the engine operation. and his sensivity against these changes.
22
Source: Folke Fritzon, Scania
23
Link to report: http://www.sgc.se/ckfinder/userfiles/files/SGC246_eng.pdf
31/48
Natural "boil off" gas from the top of the tanks for propulsion is very high in methane and has good
knocking stability. It is therefore particularly well suited as an engine fuel. However, when a propulsion
system is specially designed for this use, it is important, to ensure, that there is always enough natural
boil-off gas with high methane content available, so that any need for mixing in forced boil-off gas
from the bottom of the tanks in order to maintain the power is limited. If this is nevertheless required,
the operators must be aware that the knocking stability of the gas will be reduced and that
appropriate precautions concerning engine power or ignition timing will have to be taken in order to
avoid knocking.
Engine installation specially designed to be fuelled by LNG should preferable be of the type forced boil
off with the LNG taken from deep down in the tanks and well mixer before extraction into the
evaporator. This will ensure good homogeneity of the LNG taken out and so constant gas quality. One
must be aware that this type of LNG-based fuel gas will be different from the natural boil off gas from
a tank top and the rating of the engine will have to be based on somewhat lower MN in this case, in
order to ensure knocking-free operation. Evaporator sizing must be sufficiently large in order to ensure
that no gas droplets are entering the engine even under severe transient operation.LNG is the
preferred fuel for long haul truck since it has significantly higher energy density. LNG is also the
preferred fuel to use for DDF technology since LNG normally has higher knock resistance (due to
higher content of methane) than CNG and also allow for extra cooling from the evaporation which is
beneficial in DDF engines.24Some key parameters discussed regarding LNG and EURO 6 engines are:
• Methane Number:The higher MN the better possibility to optimize engine

• Wobbe Index:Narrow interval helps to fulfil EURO 6 in terms of specified power and torque.
• Temp./Pressure :Technology road path indicates need of two pressure intervals:
Spark ignited: minimum~10 bars
HPDI and similar technologies: “As cold as possible”
• Siloxanes:Limit needed to secure engine durability (risk of abrasion and increased probability
for knocking)
And also there are some aspects to be considered, related to gas quality, which affect to the engine
and gas infrastructure.
• Hydrogen: risk of embrittlement for the metallic materials

• Water: risk of corrosion and driveability problems.
• Hydrogen sulfide, H2S: corrosive in the presence of water, could affect after-treatment devices,
combustion products could create problems by sticking the engine valves.
When talking about methane fuel for automotive applications, the main engine technology always has
been the Otto engine, either under stoichiometric or learn-burn conditions of the air-fuel mixture. That
has been thus until the appearance of the dual-fuel engines which are compression-ignition based
engines.The difference in the functioning principle causes also relevant differences in the pollutant
emissions derived from these engines, and thus also significant differences to the after-treatment
strategies. Some of the main differences:
24
http://www.cimac.com/cimac_cms/uploads/explorer/Working%20groups/CIMAC_WG17_LNG_po
sition_v7_rev.pdf
32/48
• Stoichiometric spark-ignition natural gas engines: characterized by a homogeneous air-fuel

mixture, the air-fuel ratio being controlled via an oxygen sensor (or lambda sensor) installed in
the exhaust stream.
• Lean-burn spark-ignition NG engines: characterized by a stratified air-fuel mixture. These
engines usually require indirect fuel injection or a direct fuel injection with induced turbulence.
The indirect fuel injection requires the fuel to be injected in a pre-chamber designed, to keep
the air-fuel mixture at stoichiometric conditions until it is suctioned into the combustion
chamber. Excess of oxygen concentration in the exhaust is controlled via a linear oxygen
sensor.
• Dual-fuel compression-ignition NG/Diesel engines: dual-fuel engines differ from dedicated
engines in their capability to burn two fuels at the same time. Dual fuel engines use diesel as
the main ignition source for the natural gas-air mixture. Diesel substitution ratios can vary
depending on the dual fuel engine technology and also depending on the operation of the
engine itself.
Theoretically, energy efficiency is higher and engine-out emissions are lower for lean-burn engines
than for stoichiometric engines. However, the stoichiometric engine is able to control emissions
efficiently via a three way catalyst (TWC), which oxidizes CO and HC while reducing NOx. Due to the
excess oxygen, TWCs can’t be used for lean-burn engines. Instead, oxidation catalysts are used to
oxidize CO and HC, but without an effect on NOx. For the dual-fuel engine, the current and future
emission legislations (EURO V and EURO VI) require that the engine is equipped with similar after-
treatment technology as diesel engines, which means installation of a selective catalytic reduction
(SCR), an oxidation catalyst and a diesel particulate filter (DPF). NGVs equipped with TWCs meet even
EURO VI NOx emission requirements.25
5.1 Methane number

The MN of a fuel gas is the main factor to determine risks of knocking and misfiring. However the
importances of the MN on the knocking depends on the engine architecture (direct injection, indirect
injection) and its technology (gas engine or dual fuel engine, etc.).
Some Engines manufacturers claim that when the MN is bellow of 80 the concentration of heavy
components (Butane, Pentanes, etc.) is high, premature auto-ignition of these components causes
vibratons and knocking (shocks).
When the MN is higher than 110, the concentration of non explosive components (N2, CO2) is high
and leads to misfiring.
It is necessary to work for determine the MN method of calculation of the gas. In fact several
calculation methods exist but none of them has been unanimously accepted.
25
http://www.iea-amf.org/content/fuel_information/methane#emissions
33/48
5.1.1 Methane number calculation26

The knowledge about the methane number is important, among other things, because the
manufacturers can only optimise engines if they know to which minimum methane number the engine
will have to handle. High methane numbers mean high knock resistance; high knock resistance, in turn,
means high efficiencies and thus lower CO emissions. If methane numbers are too low, knock may
cause engine damage or lead to losses in efficiency and performance if engine operation has to be
adjusted to avoid knocking combustion. A low methane number might also have detrimental (rising)
impact on the emissions of the engine.
The calculation methods are the followings:
• Calculation of Methane Number from Motor Octane Number (ISO 15401-1:2006: Natural gas –
Natural gas for use as a compressed fuel for vehicles — Part 1:Designation of the quality):
o Linear Correlation method.
o Hydrogen/Carbon (H/C) Ratio method
• One of the most frequently used method for determining the methane number was developed
by AVL in the 1970s. For all existing pipeline quality natural gases the AVL method for
determining the methane number works reliably and sufficiently accurate if nitrogen is
excluded from the gas composition. The AVL calculation tool is proprietary, however it can be
licensed from AVL for a small fee.
• EON-GasCalculation produces end results similar to those of the AVL programme. EON-
GasCalculation has the additional advantage that corrections for Nitrogen can be easily made.
When using EONGasCalculation the option without Nitrogen should be used.
• Various engine manufacturer methods.
It should be noted that today’s methods for calculating the methane number were developed for the
natural gas qualities we currently see in pipelines. If in the future new types of gas, which comprise C5
and higher, are included in pipeline gas, corrections need to be made when calculating the Methane
Number. This includes a number of rich LNG qualities currently on the market.
In case hydrocarbons higher than butane are present, additional corrections have to be made to
compensate for the high knock sensitivity of these components.
26
www.gie.eu.com/index.php/publications/doc_download/19528-gie-position-on-including-
methane-number-in-eu-standard-for-natural-gas
34/48
Figure 5-1 Variations of MN depending on the calculation method (2008-2009)
It should also be noted that some of these calculation methods do not consider components heavier
than butane. As the quantity present should be small these additional components are normally added
to the quantity of butane as an approximation, but for Methane Number determination, additional
development of the calculation method may be needed.
Similarly, the only methods to calculate Methane Number included in an international standard (ISO
15401-1:2006) were not developed to or are not able to predict the right trend of Methane Number
when hydrogen is injected to the natural gas.
During the European Comission Workshop on Gas Quality held on 5 December 2011 is considered the
different possibilities to decide a range of methane number for use. As you can see in the following
figure if the range of methane number considered is between 80 and 100 which would exclude the
majority of avalaible LNG from coming Europe.
During the European Commission Workshop on Gas Quality held on 5 December 2011, Euromot asked
for a Methane Number between 80 and 100 which would exclude the majority of available LNG from
coming to Europe as shown in the figure 6-2.
It was proposed during a CEN/TC 234 WG 11 meeting to set the methane number >65 (±2 calculated
with AVL method) in the European gas standard. This lower limit would cover all the supplies currently
coming to Europe. It should also be noted that representatives of the automotive industry
participating in the CEN/TC 19 have confirmed that a methane number of 65 could be acceptable (but
raised to 75 in the future, which would endanger security of gas supplies to Europe).
35/48
Figure 5-2 Methane Number (AVL method) vs. Wobbe Index for LNG dource during 2011
The proposal on the range to methane number between 80 and 100 was to EUROMOT, his argument
is that a MN below 80 reduces the efficiency of the gas fuelled reciprocating engines and may incrase
the emissions or create problems to the engine as it is shown in the following figure.
Figure 5-3 Example of efficiency of gas motors (CHP) for different methane numbers
5.2 Impact of Gas Characteristics on the Dual Fuel Operation –

engines derating
Influence of the quality of gas is confirmed in operation; troubles with gas quality (high nitrogen
content & superheated LNG) have been observed leading to a derating of the Dual Fuel engines and
therefore a speed limitation.
5.2.1 Knocking
Knocking problems have been experienced due to the Gas Quality and High Temperature, illustrated
by two examples:
36/48
First Example: on ballast voyage, in the case experienced, the forced boil off content had been about
30% of total gas consumption.
Engines tripped many times from Gas to Diesel Oil. When content of forced boil off had been reduced,
from 30% to about 8%, knocking phenomenon has decreased significantly.
The heavy carbon removal tank fitted on board was not sufficient to face this higher flow of forced
boil-off.
In order to run in best way, the gas quality must be considered during uploading and transfer to have
even load and stable temperatures during transfer.
It’s has been observed as well that the impact of gas quality is depending on engines running hours
and ambient temperature conditions
Electronic control of the combustion is very sensitive. Depending on the different loads and various
conditions, engine needs time to “learn” and adjust them selves. In particular in duration offsets of the
gas valves of each engine due to total running hours. A too big offset step during switch-over and
transfer, will make the cylinder drop out or start knocking.
Second example: a couple of times, High exhaust gas temperature was observed and exhaust gas
valves burnt leading to the replacement of cylinder covers.
Dual Fuel Engines Maker, Wärstilä is considering that this failure of the exhaust valve may be due to
dust deposit, originated from lubrication oil
But it was as well observed that the engines having higher exhaust gas temperatures made them more
sensitive regarding knocking. Therefore gas quality could be one of the root causes of these damages.
5.2.2 Misfiring
After loading the percentage of nitrogen could reach 30% in the Boil-Off Gas composition; therefore
to avoid misfiring, gas admission valve of the engines should remain open longer to allow the
admission of the required quantity of methane
A standard fuel content specification for LNG is currently under development. Indications are that
these standards will allow reasonably low levels of methane content (less than 90%). This means that
engines designed to this standard may be capable of accepting fuel that has experienced a higher
degree of weathering. Under lower methane content standards, there will be an even greater need to
be aware of the quality of fuel as it is delivered, and to properly manage fuel usage.
For better understanding of the LNG's Wathering we explain this phenomenon in a form more detailed
bellow.
Wathering is one effect of LNG’s cryogenic properties, and it is important to understand, especially
when LNG is to be used as a vehicle fuel. This effect, called “weathering” or “enrichment,” is a
phenomenon that arises from the fact that natural gas is a chemical mixture. LNG produced from
pipeline gas has varying percentages of methane and other hydrocarbons. The methane content can
vary from 92% 99%. The other hydrocarbons found in natural gas are ethane (1% 6%), propane (1%
37/48
4%), butane (0% 2%), and other compounds. Each chemical element or compound in the liquid
vaporizes at its own unique boiling point.
Consequently, over time, concentrations of the heavier hydrocarbons (such as ethane, propane, and
butane) increase. Higher concentrations of these hydrocarbons will cause premature ignition and
“knock.” Because uncontrolled knock causes engine damage, LNG must be used before it becomes
weathered. Recognizing this potential difficulty, Liquid Carbonic set out to manufacture 99.4% pure
methane LNG. With this high percentage of methane, LNG weathering cannot create harmful fuel
mixtures because the potentially harmful constituents are largely absent.
5.3 Silloxanes
The European Comission presented to CEN a standarization Mandate, M/475, for biomethan in
November 2010. The aim was for the development of a European Standard for quality specification for
biomethane to be used as a fuel for vehicle engines and to be injected in natural gas pipelines.
This work is done by CEN/TC 408 “Project Committee – Natural gas and biomethane for use in
transport and biomethane for injection in the natural gas grid”. They draft of a common list of
parameters which should be included in the standard (Common (fossil) gas distribution requirements,
requirements for injection into the grid and additional requirement for use as automotive fuel).27
Among the parameters identified, siloxanes are expected to have potential impacts on the engines and
appliances. Siloxanes are organosilicon compounds found in fermentation gases from landfill and
waste water treatment. Upon combustion, siloxanes in biogases from silicon dioxide (silica SiO2), which
is known to deposit in engines, domestic equipment and turbines.
The deposition of silica in engines causes a number of problems. Ignition failure can occur as a result
od filica deposits that cover and electrically insulate the spark plug. Small silicon dioxide particles can
also cause wear of the engine as these sand-like particles are very abrasive. SiO2 accumulates in the
lubricating oil and coats/lacquers the cylinder wall filling the honing pattern thus ruining the
lubrication of the engine.
A study28 revealed that large ash content in the oil may even enhance the silica depposition. Large
build-up of deposits increases the compression ratio of an engine which promotes knock. Heavy
knocking can destry an engine in seconds. Compressed Natural Gas vehicles running on biomethane
may experience additional problems, for example, silica deposition can mask the catalyst thus lowering
the catalysts efficiency and increasing the emissions. Besides this effect, sillica deposition can also
affect the functioning of sensors installed in the engine.29
27
http://www.afnor.org/en/news/news/2013/march-2013/biomethane-for-injection-in-the-natural-gas-grid-
and-for-use-a-fuel-for-vehicle-engines-call-for-tenders-from-cen
28
Einfluss der Schmierölwahl auf den Betrieb von Gasmotoren mit Biogasen. MWM Dessauer
Gasmotorenkonferenz | 26. März 2009
29
https://www.sgn.co.uk/uploadedFiles/Marketing/Content/SGN-Documents/Environment-Docs/SGN-
Siloxanes-In-Biomethane-Apr-13.pdf
38/48
Organoziloxanes are semi-volatile organosilicon compounds which, while not an aggressive gas
component in terms of emissions, can be converted to solid inorganic siliceous deposits within the
engine combustion chamber. They form a coating or lacquer on all surfaces contacted by the
lubricating oil and can alter the oil retaining surface finish of cylinder liners.
The siloxanes can:
• Enter the engine as insoluble matter in the gas fuel, forming a white deposit in the combustion
chamber.
• Be produced in the combustion chamber itself.
Siloxanes in the landfill and sewage gas convert into silicon dioxide when combustion takes place
in the engine. The silicon dioxide combines with other elements in the gas, and with the
lubrication oil to form a hard matrix that accumulates on the combustion surfaces.
With the deposits accumulate, the engines efficiency falls causing detonation in the combustion
chambers. The resultant unburned fuel contaminates the exhaust gas increasing emissions. At this
point the engine may need to be "de-rated” (Output reduced) to prevent significant engine
damage and to reduce emissions.
If run unchecked, severe damage can occur to valves, pistons, piston rings, liners, cylinder heads,
spark plugs and turbochargers, necessitating premature servicing and costly repairs.30
• From a golden lacquer on components outside the combustion chamber. This lacquer can be
especially evident o the piston-ring wiped surface of the cylinder liner. The lacquer has a
tendency to fill the oil retaining honing pattern but rarely builds to the excent of requiring
attention prior to routine overhaul.
30
www.pptek.co.uk Brochure “Siloxane contamination and solutions”
39/48
Figure 5-4 Golden laquer of siloxanes bild-up evident on cylinder liner
At the combustion conditions within landfill gas engines, organic silicon compounds present in the
landfill gas may be deposited on the cylinder head as solid inorganic silicon compounds. This
deposited material is white to light grey, somewhat laminar, generally opaque, and may exhibit a
partial to poor crystalline structure. Few analyses of these deposits are given in the literature; existing
data indicate that crystalline SiO2 is present alongside other metals in solid forms (Niemann et al.,
1997; Hagmann et al, 1999; M. Niemann, personal communication, 2001).
These deposits severely reduce engine life. The engine has to be stripped down and the solids scraped
manually from the piston, cylinder head and valves.
During the combustion process, some silicon compounds are also partitioned to the engine oil, which
needs to be changed more frequently at sites with high siloxane levels in the inlet gas fuel. Engine
manufacturers thus recommend direct monitoring of silicon build-up in the engine oil. The increasing
use of these compounds in consumer and commercial products suggests that problems with volatile
siloxanes in landfill gas engines are likely to increase.
Siloxanes do not directly cause problems with gas engine exhaust emissions, though the increased
wear may show itself as an increase in SOx emissions as lubricating oil is burnt. Typically, this is unlikely
to exceed any risk-based criterion for emissions management and the decision to implement gas
clean-up for siloxane management purposes is entirely based on cost.31
31
www.sepa.org.uk “Guidance on gas treatment technologies for landfill gas engines” - .www.environment-
agency.gov.uk
40/48
5.4 Hydrogen
In the context of the development of renewable energy sources there are various projects in Europe
focusing on the injection of Hydrogen into the gas grid. It should be noted that any addition of
Hydrogen (Methane number 032) will decrease the Methane Number of the gas transported, potentially
limiting that supply or preventing the use of this form of renewable energy. In particular the following
technical limitations have to be assessed:
• Stress cracking at steel installations, which might potentially occur under typical gas storage
operations (Cycle pressure loading).
• Possible substrate for undesired bacteria.
• Possible production of organic acid or hydrogen sulphide.
• Possible undesired impact on gas engines.
Additional parameters and limitations will be developed and reported later in the LNG-BC project.
32
Pure Hydrogen is used as the knock sensitive reference fuel with a methane number of 0.
41/48
6 Measuring gas quality

The combination of small scale LNG, use of LBG, potential change of gas quality along the delivery
chain and varying sensitivity of gas quality for different truck engine technologies increase the need to
be able to secure that the delivered fuel is following the agreed specification.
Based on experiences from the CNG market it is also expected that a developed LNG-market for trucks
will require an open ongoing dialogue regarding interaction between gas quality delivered to the
trucks and the robustness of the truck engine technology.
As the gas quality for LNG might vary along the delivery chain the measuring shall be able to be done
at the filling station. Testing equipment is available commercially but normally designed for large
scale LNG terminals. To be able to take recurrent tests at truck refueling site a technology and
methodology for taking low-cost representative gas samples is required.
Based on financing from actors participating in LNG-BC a test method different gas qualities has been
developed and described in a separate report, “SGC rapport 288 Method development for gas quality
determination in the LNG storage of a LNG/LCNG refueling station”, see link below33. As main results
the ability to take representative tests has given satisfying results, proven by careful evaluation towards
experimental and calculated gas qualities. Some further improvements needs to be done especially
regarding heat exchange in the vaporizer. The LNG-BC project will further consider results from this
study and also include additional potential projects in this area to make cost efficient gas quality
testing more widely available. This will be described in the coming project delivery D3.11 “Studies
regarding ageing of fuel”.
The actual results from tests described in the SGC report 288 shows that regardless if LNG or LBG is
used the gas quality in liquid phase is changing, but not significantly, as the level of fuel in the storage
tank is getting lower and lower. For LBG an increase of concentration of methane in gaseous form was
measured, while the concentration of methane in liquid form decreased from 99,0%-vol, when storage
tank was just refueled, to 97,9%-vol. when a quarter of the tank remained. For LNG an increase of
ethane was measured both in gaseous and liquid form. Another result from the study was that
blending LNG and LBG in the same storage quite rapidly mixed together to the expected quality. Only
1- 2 hours after blending the LNG and LBG the measured result was in line with the expected gas
quality for the blended fuel qualities. Generally, additional tests need to be done to confirm the initial
results.
33
Link to report: http://www.sgc.se/ckfinder/userfiles/files/SGC288.pdf.
42/48
7 Conclusions
Gas quality will vary depending on the source of LNG, the production of LBG and the handling of the
fuel along the distribution chain up to the delivery of the truck. The variation of the gas quality will not
be a show-stopper, but could affect the possibility of optimizing truck engines and will also continue
to be an issue of interest after the launch of trucks on the market. Therefore, continuous focus on gas
quality will remain to be a critical area to keep track on.
In the LNG supply chain most BOG is generated by the LNG ships themselves. The used LNG cargo or
losses of LNG cargo due to boil-off reduce the amount of cargo delivered by LNG tankers to the
receiving terminal while the ageing process steadily changes the composition, quality and properties
of LNG cargo during a ship’s voyage. Therefore, the quantity and quality of unloaded LNG are the key
factors for the economic assessment of the LNG supply chain.As described below, geopolitical
relations can make a country to use a rich or lean gas (USA uses in majority gas coming from Alaska).
Despite these differences, each country has its own way to manage the gas quality. Japan and the USA
are able to keep a similar gas quality over the country thanks to different management process. From
the other side, Europe shows a high diversity between the different countries. Due to different gas
specifications, each member imports its gas from several parts of the world so the quality at each
terminal differs on the composition (Methane Number, Wobbe Index…). To get a similar quality on
Europe, several measures have to be applied starting by introducing quality standards. To establish
these standards different processes can be used as:
• Ballasting (N2 injection to reduce the Wobbe Index)

• Propane / Butane injection or removal (for small Wobbe Index corrections)
• CO2 or N2 removal ( only applicable for pipeline gas)
• Blending ( Blend of LNG coming from different sources)
These measures can help to make the LNG available through Europe in the way to interchangeability.
During the report we have explained different topics related to LNG vehicle technology which could be
affected by gas quality. New design parameters depending on technology platform might be found or
highlighted during the demonstrations. This needs consideration regarding benefits of the amount of
increased efficiency in vehicle technology vs. possibilities to provide specific gas quality at competitive
price for customers.
The test method of taking samples of gas quality at the LNG filling station will have to be further
developed. The increased ability to follow-up the gas quality at the filling station will lead to improved
fact-based knowledge that in turn will facilitate defining potential causes of quality problems, thereby
improving the LNG market for trucks as a whole.
As we already explained before Euromot recommend a methane number to 80, in this report about the
gas quality, the topic to market, we have shown that this number would endanger the security of
natural gas supply to the European Market.
Another important aspect to consider is that there is no commonly agreed Methane Number
calculation method and one would need to be agreed, or even developed and made available in the
public domain.
43/48
Including the Methane Number in the European Standard requires an agreed and reliable method of
determination and should incur minimum costs.
The Methane Number can’t directly be used to optimise engine operation as there is no guarantee
that the Methane Number at the point of measurement will correspond to the gas quality at the
engine. Automation of engine emissions monitoring and automatic optimisation is the best method of
ensuring optimum operation over a range of gas qualities.
The influence of hydrocarbons from biomass gasification on the fuel quality is not that different from
that corresponding to hydrocarbons from NG. It is not worth to have a fuel production line different
from that of LNG the gas from gasification should be cracked to syngas and converted to the final fuel.
However the CO2 and H2 removal in the final upgrade should be optimized to meet specific value of
MN and LFL (Lower Flammable Limit) instead of Wobbe index, used for injection in the NG grid.
Talking about reducing the effect of silicon dioxide deposits, in the engine, various methods have been
employed. Fluid injection systems do allow the silicon matrix to soften making removal easier, however
in the long term it is preferable to remove the siloxanes from the gas before they reach the engine
preventing the formation of deposits. This aspect is very important in order to ensure the engine life.
Active carbon filtration systems are available, it filters the contaminants for a finite period. These can
be long installations (Requiring planning permissions) and need manual removal of spent activated
carbon and disposal of the contaminated medium. Recently derivatives of the active carbon principal
have been developed which offer a cartridge / silo replacement and removal service of the spent
carbon. Although this avoids some of the disposal and safety issues, it is costly and requires constant
maintenance. Normally these installations have a large footprint and require site planning before
commissioning and a costly chiller to remove the water from the gas.
44/48
8 Recommendations for the LNG-BC project

Based on the conclusions in this report it is recommended that the project LNG-Blue Corridor project
keeps continuous attention to the issue of gas qualities by keeping the dialogue open between the
actors. This discussion is going to be developed through the trials developed during the project. The
importance of the gas quality is going to be analyzed.
In order to ensure the european import, export and market it is necessary to create, or develop gas
quality standarization. The progress in gas interchangeability is vital for the market development and
work in the study of the vehicle technology.
One important topic recomended about the LNG quality is to ensure a common MN calculation
method for the standarization in the european market and to have a reliably criteria.It is important to
know the MN and LFL index in order to optimize engines, instead of wobbe index which is used to in
injection to grid gas.
In order to ensure long engine durability, it is important to reduce the siloxanes the fuel. For this
reason is necessary to study the best way to perform the cleaning or filtration. In this report is talked
about the active carbon as possible solution.
• About the topic to discussions on how to find marked- and technology solutions to handle
varying gas qualities, bellow detailed a list about it has already been done during the project
and which is being worked on:Sourcing of gas
• Fuel management solutions throughout the delivery chain.
• Solutions to secure gas quality are kept within agreed specification.
• Measuring of gas quality in small scale LNG facilities
• Evaluation regarding design criteria and possibilities for different engine technologies to be
optimized toward different gas qualities in terms of robustness, engine efficiency and emission
control. The project consortium is recommended to monitor and report accordingly during the
demonstration period, at what extent gas quality will effectively influence engine performance,
setting through substantiated observations the range of quality indicators and parameters
jointly with target range values to be met to ensure proper functioning of engines
45/48
9 Glossary
Biogas Raw gas from digesting plant. To yet upgraded to vehicle quality. High content of
CO2 (~40%)
Biomethane Upgraded biogas suitable as vehicle fuel
BOG Boil-Off Gas
CBG Compressed Biomethane
CNG Compressed Natural Gas
DFE Diesel substitution factor – The share of diesel replaced with gas in a duel-fuel engine.
Dual-Fuel Engine technology based on compression ignition, mixing diesel and gas.
EURO class European emission standard. EURO 5 valid for trucks sold until end of 2013. All trucks
sold on market from 2014 must fulfill EURO 6.
H-Gas Gas with methane content between 87 und 99,1 Vol. %. Energy content is normally
between 10,0 to 11,1 kWh/m3, i.e. high energy content compared to L-Gas, see below
LBG or LBM Liquefied Biomethane suitable as vehicle fuel.
L-CNG CNG station with the gas provided by an LNG tank
station
L-Gas Gas with methane content between 79,8 und 87 Vol. %. Energy content is normally
between 8,2 to 8,9 kWh/m3. Offered on some markets mainly due to historical
reasons to be compatible with existing appliances.
LNG/LCNG Refueling station using liquefied gas for storage offering both liquefied and
station compressed gas to vehicles.
46/48
References
List of Tables
Table 2-1 Boilin temperatures and densities – LNG Componenets .........................................................................9
Table 2-2 Parameters in ISO 15403:2006 .......................................................................................................................... 16
.
Table 2-4 Examples of aspects covered in biomethane standard SS 15 54 38 ................................................ 16
Table 4-1 Worldwide average LNG compositions ......................................................................................................... 20
Table 4-3 International Comparision of Wobbe Index Ranges ................................................................................ 23
List of figures
Figure 1-1. Impression of the LNG Blue Corridors............................................................................................................6
Figure 2-1. Composition CNG and LNG ................................................................................................................................9
Figure 2-3 the saturation curve for natural gas (100% methane), defines the conditions where the liquid
and vapour phases can coexist (ºF=1.8 ºC+32 and 1psi=6.90 kPa) ....................................................................... 12
Figure 2-4 pressure-density conditions of LNG fuel systems ................................................................................... 13
Figure 2-5 Temperature-density conditions of LNG fuel systems........................................................................... 14
Figure 3-1 Generic description of different distribution chains for LNG and LBG ............................................ 18
Figure 4-1 worldwide overseas LNG importation ......................................................................................................... 21
Figure 4-2 Development of gas quality specifications ............................................................................................... 26
Figure 4-3 Composition of European pipeline gas and LNG (the relative size of the bubbles indicates
the methane content); Source Report EUR 23818 EN .................................................................................................. 27
Figure 4-4 Physical properties of European pipeline gas and LNG (the relativesize of bubbles indicates
the density of gas relative to air) Report EUR 23818 EN............................................................................................. 27
Figure 4-5 Typical Wobbe index for LNG source ........................................................................................................... 28
Figure 4-6 Wobbe number requirements at EU LNG import terminals ................................................................ 28
Figure 4-7 Wobbe Index region and the consequences of operating in objectionable ranges ................. 29
Figure 4-8 Worlwide heating value specifications ......................................................................................................... 29
Figure 5-2 Methane Number (AVL method) vs. Wobbe Index for LNG dource during 2011 ...................... 36
Figure 5-3 Example of efficiency of gas motors (CHP) for different methane numbers ................................ 36
Figure 5-4 Golden laquer of siloxanes bild-up evident on cylinder liner ............................................................. 40
47/48
Partners

LNG Gas Quality PDF

Uploaded by

Copyright:

Available Formats

LNG Gas Quality PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LNG Gas Quality PDF

Uploaded by

Copyright:

Available Formats

EUROPEAN COMMISSION

SEVENTH FRAMEWORK PROGRAMME

GC.SST.2012.2-3 GA No. 321592

Deliverable No. LNG BC D3.2

Author Organization Description

5.2.1 Knocking ........................................................................................................................ 36

Figure 1-1. Impression of the

1.2 Aim of this deliverable

2 Gas quality – Compressed vs. Liquefied

2.1 Differences between CNG and LNG

Figure 2-1. Composition CNG and LNG

2.2 LNG specifications 3

Table 2-1 Boilin temperatures and densities – LNG Componenets

Boiling temperature at Liquid density (kg/dm3)

Nitrogen -195.8 0.810

Methane -161.5 0.421

Ethane -88.6 0.546

Propane -42.0 0.585

N-Butane -0.5 0.600

2.2.1 Methane number

Figure 2-2. Methane number versus Wobbe index of importers LNG

2.2.2 LNG saturation

Figure 2-4 pressure-density conditions of LNG fuel systems

Figure 2-5 Temperature-density conditions of LNG fuel systems

2.2.3 Wathering of LNG fuel8

2.3 LNG fuel quality standarization

Criteria handled in ISO15403:2006 are:

Table 2-2 Parameters in ISO 15403:2006

Parameter Level Unit

CO2 < 0.03 Volume fraction

Table 2-4 Examples of aspects covered in biomethane standard SS 15 54 38 10.

Wobbe index lower: 43,9 – 47 MJ/m3

Water content max. 32 mg/m3

3 LNG delivery chain

4 Gas quality by market: source, import and

Table 4-1 Worldwide average LNG compositions

Parameter Lidköping Biogas (SE) Gasrec (UK) Unit

4.1.2 Western Europe

4.2 Differences between the markets

• Group L: 39.1 < W < 44.8 MJ/m3

Table 4-3 International Comparision of Wobbe Index Ranges

USA White Paper3 ± 4.0% Wobbe

UK GS(M)R ± 4.3% Wobbe

EASEE-gas Proposed CBP Gas Quality ± 5.6% Wobbe

France Transmission Entry Spec. ± 7.0% Wobbe

Germany National Standards ± 10.1% Wobbe

Italy National Standards ± 5.0% Wobbe

Korea National Standards ± 4.6% Wobbe

New Zealand National Standards ± 6.1% Wobbe

UAE Abu Dhabi Spec. ± 3.0% Wobbe

4.3 Gas Quality Management 15

• Ballasting with inert gas.

4.3.2 Propane/butane removal/injection

4.3.3 Carbon dioxide or nitrogen removal

Energy content Gross Calorific Value Billing

4.4.1 Country Gas Quality Programmes

4.4.2 Interchangeability parameters19

Different interchangeability measures have been specified by countries.

Figure 4-5 Typical Wobbe index for LNG source