FAQ Install An eCOM PartP Interface With DTS V8.06

FAQ frequently asked questions
How To: Install an eCOM Part P Interface with DTS V8.06.xxx

Requirements
• Diagnostic Tool Set with a version of at least 8.06.011
• eCOM interface with USB to Ethernet Converter
• Windows 7 or Windows 8.1
• Administration rights for your computer
Prepare your eCOM Hardware
If you use the OBD cable to connect your eCOM to the vehicle busses, it will be power-supplied by the vehicle this way.
When you use the Part F connector box, you should power the eCOM over the connectors Vbat and GND of the Part F box.
Connect the CAN Bus of your test setup to the CAN sockets of the Part F box. Unless your DTS project specifies other CAN
connection pins, use CAN1 sockets. Make sure your bus is terminated correctly. Check polarity of the CAN lines, when connecting
them to your CAN bus.
Install the Hardware Driver
The hardware drivers for the USB to LAN adapter are provided in the folder 3rdPartyDrivers of your DTS 8 installation media. Choose
the correct driver for your operating system, i.e. AX88772A_772_Win7_v3.x.5.0_Drivers_Setup_v2.0.1.0 for Windows 7 and
AX88772C_772B_772A_772_Win8.x_v3.16.10.0_Drivers_Setup_v3.0.3.0 for Windows 8.
For a more up to date driver you also may download the most recent version from the webpage of ASIX Electronics Corporation
http://www.asix.com.tw/products.php?op=pItemdetail&PItemID=97;71;101&PLine=71. Select AX88772A and search for the Windows 7 32-bit/64-bit WHCK drivers
setup program or, in case of Windows 8, the Windows 8.1/8.0 32-bit/64-bit WHCK drivers setup program. Download the archive file to a local disk drive and unzip it.
Make sure the eCOM interface is not connected to your computer yet.
Start the Setup.exe installation program in the folder you have unzipped the archive. You need administration rights to execute the
driver installation successfully. Confirm any UAC (user account control) requests.
After the Setup was finished, power the eCOM interface and connect it with the USB to Ethernet Converter to a USB port of your
computer. Let Windows install the drivers for the device.
A new virtual network adapter named ASIX AX88772A USB2.0 to Fast Ethernet Adapter will be created on your computer.
Setup the Network Connection
Usually you do not have to do any configuration for the eCOM USB to LAN adapter. Windows assigns an Automatic Private IP
Address in the range 169.254.x.x/255.255.0.0 to the adapter. This address corresponds to the default IP settings of the eCOM
interface (169.254.255.42/255.255.00).
FAQ - How To: Install an eCOM Part P Interface for DTS V8.06.xxx 2015/09/27 – V 1.00
[email protected] Hotline: +49 (0) 89 4565 444
ASIX AX88772A USB2.0 to Fast Ethernet Adapter:

Default TCP/IP settings for use with Automatic Private IP Address
In case of problems or when the Automatic Private IP Address does not work for you, please assign the adapter ASIX AX88772A
USB2.0 to Fast Ethernet Adapter a static IP Address:
On Windows 7 open item Network and Internet in Windows Control Panel. Select View network status and tasks. Click Change
adapter settings on the left side. Choose the LAN-Connection that was created for the ASIX AX88772A USB2.0 to Fast Ethernet
Adapter. Double Click the LAN connection icon.
Select Internet Protocol (TCP/IPv4) and press the button Properties.
ASIX AX88772A USB2.0 to Fast Ethernet Adapter:

TCP/IP settings with static IPAddress
Choose Use the following IP address and enter the static IP address 169.254.255.41 with the subnet mask 255.255.0.0 in the
appropriate fields. Click OK and close the Local Area Connection Properties window.
Firewall Issues
eCom requires the ports 4500, 4394 (TCP) and 4009, 4011(UDP) not to be blocked by a local Firewall. The network connection may
also be restricted by other security software as virus protection software.
Check the Network Connection
Open a Command Prompt and enter ping 169.254.255.42. You should see ping responses from the eCom as shown below:
Install Diagnostic Tool Set 8 with Daimler Add-On
If you did not install Diagnostic Tool Set 8 yet, please start the DTS V8 Setup by executing the file Setup.exe. This will install the
Standard Version of Diagnostic Tool Set 8 without the Daimler Add-Ons. To install the Daimler Add-Ons please execute the Daimler
Add-On Setup Addon_DAG_Setup.exe after the Standard Version Setup has finished.
Start the DTS System Configurator from the program group Diagnostic Tool Set 8\Tools in the Windows Start Menu.
Open the item Interfaces in the System Settings tab on the left side.
Make sure the eCOM_SMR entry is check-marked and the settings correspond to the settings shown in the following image. The
eCOM_SMR entry is required when you work with ODX (i.e. SMR) files and your ECU is connected to a CAN bus.
Make sure the DoIP_SMR entry is check-marked and the settings correspond to the settings shown in the following image. The
DoIP_SMR entry is required when you work with ODX (i.e. SMR) files and your ECU is connected to a Ethernet bus.
Make sure the eCOM_CBF entry is check-marked and the settings correspond to the settings shown in the following image. The
eCOM_CBF entry is required when you want to use Caesar binary files on a CAN or Ethernet bus.
Start Monaco
Start Monaco and open the Monaco workspace of your DTS project.
Check the communication to a vehicle or ECU.
Contact [email protected] for further help.

FAQ Install An eCOM PartP Interface With DTS V8.06

Uploaded by

Copyright:

Available Formats

FAQ Install An eCOM PartP Interface With DTS V8.06

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FAQ Install An eCOM PartP Interface With DTS V8.06

Uploaded by

Copyright:

Available Formats

FAQ frequently asked questions

How To: Install an eCOM Part P Interface with DTS V8.06.xxx

• Diagnostic Tool Set with a version of at least 8.06.011

• eCOM interface with USB to Ethernet Converter

• Windows 7 or Windows 8.1

• Administration rights for your computer

Prepare your eCOM Hardware

Install the Hardware Driver

Setup the Network Connection

ASIX AX88772A USB2.0 to Fast Ethernet Adapter:

Select Internet Protocol (TCP/IPv4) and press the button Properties.

ASIX AX88772A USB2.0 to Fast Ethernet Adapter:

Check the Network Connection

Install Diagnostic Tool Set 8 with Daimler Add-On

Check the communication to a vehicle or ECU.

Contact [email protected] for further help.

You might also like