TECHNICAL HANDBOOK

PRE-ENGINEERED BUILDINGS
PEB Skeleton Structure

1. Concrete Footing 8. Framed Opening (Window/Louver) 15. Lean To Frame 22. Eave Strut
2. Anchor Bolts 9. End Wall Wind Column 16. Crane Beam 23. Side wall Girt
3. Base Plate 10. Roof Bracing (Angle/Rod/Cable) 17. Crane Column 24. Flush Fascia Frame
4. End Wall Girt 11. Main Frame Rafter 18. EOT Crane 25. Cage Ladder
5. Portal Bracing 12. Jack Beam 19. Roof Purlin 26. Deck Panel with Steel Mesh
6. Main Frame Straight Column 13. Main Frame Tapered Column 20. Flange Brace 27. Hand Rail (Steel)
7. Wall Bracing (Angle/Rod/Cable) 14. Cantilevered Fascia Frame 21. Sag Rod 28. Staircase (Checker Plate/C Channel
29. Crane Bracket

PEB Advantages
Faster construction High quality and durability Minimal maintenance

Economical Environmentally friendly Seismic (earthquake resistant) design

Space flexibility - Larger spans for Adjustable design -Can cater to

flexible interior design future expansions (vertical and horizontal)
TABLE OF CONTENTS

INTRODUCTION
4.5 Open Web Steel Joists 44
Chapter Page
4.6 Hangar Door System 47
1.1 Introduction 1
4.7 Special Canopies 48
1.2 Drawings, Calculations & 2
4.8 Special Fascias 49
Company Profile
4.9 Built-up Roofs 50
1.3 Definition of Terms 4
4.10 Roof Monitor 52
4.11 Curved Built-up Members 53
SPECIFICATIONS 4.12 Secondary Members 54

2.1. General 16
2.2. Design 17 ENGINEERING DATA
2.3 Structural Framing 17
2.4 Roof and Wall Covering 18 5.1 Purlin & Girt 55
2.5 Accessories 20 200 Z 250 Z Section Properties
2.6 Sandwich Panel 24 5.2 Eave Strut - 0.5:10 & 1:10 56
Slope Section Properties
5.3 Cold Formed “C” Sections
STANDARD STRUCTURAL Section Properties 57
5.4 Base & Cap Channel 58
SYSTEMS Section Properties
5.5 Kirby Roof & Liner Sheeting ( KR) 59
3.1 Standard Frames 27
Section Properties & Load Tables (Steel)
3.2 Standard Loadings 28
5.6 Kirby Roof & Liner Sheeting ( KR) 60
3.3 Standard Buildings 30
Section Properties & Load
3.4 Standard Cable Bracing System 31
Tables(Aluminum)
3.5 Portal Frame Bracing System 32
5. 7 Kirby Wall Sheeting ( KW) 61
3.6 Knee Bracing System 32
Section Properties & Load Tables
3.7 Diaphragm Bracing System 33
(Steel)
3.8 Standard Eave Canopy 34
5.8 Kirby Wall Sheeting ( KW) 62
3.9 Standard Fascia 34
Section Properties & Load Tables
3.10 Standard Expansion Joint 35
(Aluminum)
3.11 Standard Endwall Systems 36
5.9 Kirby Standard Steel Panel
3.12 Standard Wind Column Spacing 37
( KCS 40-200)
3.13 Standard Wind Column Spacing 38
5.10 Kirby Decking ( KD), Light Decking 65
with Mezzanine
Section Properties & Load Tables
3.14 Standard Anchor Bolts Details 39
5.11 Kirby Insulated Sandwich Panels 67
Roof, Wall & Partition Panels
SPECIAL STRUCTURAL & PEB 5.12 KRIP Sandwich Panel Data Sheet 68
PRE-ENGINEERED BUILDING 5.13 KWIP Sandwich Panel Data Sheet 69
5.14 KCIP Sandwich Panel Data Sheet 70
SYSTEMS 5.15 Concealed Fastener Panels 71
5.16 Concealed Fastener Single Skin
4.1 Rigid Frames with Overhead Cranes 40 Cladding 72
4.2 Multi-span Frames & Trusses 41 5.17 Concealed Fastener Insulated
4.3 Multi-storey Buildings 42 Cladding Type KCIP 73
4.4 Mezzanine Flooring System 43 5.18 Concealed Fastener Insulated
Panel Cladding 74
5.19 Fiber Glass Insulated Panels 75 6.13 Valley Gutter & Downspouts 116
5.20 Fiber Glass Insulated Panel 76 6.14 Kirby "M" Liner 117
6.15 Kirby "M" Partition 118
5.21 Self-Drilling Screw 78 6.16 Light Partitions 119
5.22 Cable Bracing 79 6.17 False Ceiling 120
5.23 ASTM A36 Anchor Bolts 80
5.24 ASTM A325 High Strength Bolts 81
5.25 Standard Crane System 82 INSTALLATION DETAILS
5.26 Standard Crane System Type ‘K’ 83
5.27 Standard Crane System 7.1 Endwall Details 121
Type ‘K’ Hoist Details 84 7.2 Purlins, Girts & Eave Strut
5.28 Standard Crane System Connections 131
Type ‘K’ End Carriage Detail 85 7.3 Bracing Details 135
5.29 Standard Crane System 7.4 Expansion Joint Details 137
Type ‘K’ Load Spectrum 86 7.5 Canopy & Lean-to Connections 139
5.30 Service Loads 7.6 Fascia Details 143
Hanging Details & Allowable Loads 87 7.7 Mansard Details 146
5.31 Ventilation Calculation 88 7.8 Roof Framed Opening Details 150
5.32 Ventilation Calculation Nomograph 89 7.9 Walk Door Details 152
5.33 Kirby Insulation ( KIB-12 ) 90 7.10 Slide Door Details 154
5.34 Roof Lighting Requirements 91 7.11 Sliding Folding Door Details 160
5.35 Roof Drainage Calculations 92 7.12 Roll-up Door Details 164
5.36 Fire Protection System 93 7.13 Hangar Door Details 168
5.37 Building Material Weights 94 7.14 Crane System Details 172
5.38 Conversion Factors 95 7.15 Mezzanine Details 175
5.39 Aircraft Dimensions 96 7.16 Roof & Wall Panel Details 179
7.17 Roof & Wall Liner Details 189
7.18 Insulation Details 195
ACCESSORIES 7.19 "KR" False Ceiling Details 197
7.20 Partition Details 198
6.1 Walk Doors 98 7.21 Ridge Ventilator Details 202
6.2 Sliding Doors 99 7.22 Roof Curb & Jack Details 206
6.3 Roll up Doors 102 7.23 Window & Louver Details 208
6.4 Insulation 105 7.24 Roof Sandwich Panel Details 212
6.5 Roof Curb 106 7.25 Standard Buildings 214
6.6 Roof Jack 107 (Continuation from Chapter 3.3)
6.7 Window 108
6.8 Louvers 109
a. Louver 109
b.Sand Trap Louver 110
6.9 Translucent Panels 111
6.10 Ventilators 113
a. Ridge Ventilators
b. Powered Ventilators
6.11 Gutters, Flashings & Trims 114
6.12 Gutters & Downspouts 115
INTRODUCTION
1.1 INTRODUCTION

The purpose of the Kirby Technical Handbook Dimensions and units used in this manual are
is to assist the building designer or potential in accordance with SI-the International System
metal building owner in the proper and of Units. Where applicable, the unit now in
economical use of the pre-engineered buildings common use is also shown for reference.
( PEB ) and structural steel systems.
It is further intended that building officials, This manual is the property of Kirby Building
architects, designers, consultants and engineers Systems and will be revised periodically as
will refer to and apply the data in this manual changes are innovated. Architectural, structural
when considering approval of Kirby buildings. and mechanical adaptations shown in this
manual are intended to be typical only and
Kirby buildings are designed by professional Kirby therefore accepts no responsibility unless
engineers and this manual was prepared under specifically agreed in writing.
their direct supervision.

1
1.2 DRAWINGS,
CALCULATIONS &
COMPANY PROFILE
Prices for all buildings include one set of Company profile:
printed building installation drawings, shipper
and one building installation procedure
Kirby Building Systems is the pioneer
manual sent with shipment and four sets of
manufacturer of steel buildings and
building installation drawings issued to the
structures in GCC, Middle East, Eastern
client via the sales office prior to the time of
Europe & CIS, Africa, Indian Sub-Continent
shipment.
and South East Asia. In operation since
If required, two sets of standard computer 1976, Kirby maintains a strong reputation
calculations for main frame cross section, and for providing cost effective solutions for
load tables for purlins, girts, and covering will buildings manufactured to the highest quality
be furnished upon request. If calculations are standards. ‘Quality’ for KIRBY epitomizes
required, under no circumstances will Kirby a combination of speed of construction,
begin fabrication until one set is returned safety of the structure, sustainability against
approved, unless approval is waived in writing natural and man-made disasters, suitability to
by the client. In lieu of calculations, a Letter the purpose, unmatched pre and post­ sales
of Certification (signed by a Professional service, scalability, and substantial savings in
Engineer) can be furnished at no charge. terms of both time and money.

When requested, four sets of approval Kirby’s state of the art manufacturing plants
building installation drawings will be furnished. produce hundreds of custom made steel
No further work will be done by Kirby until buildings each year. Kirby plants are located in
one set of drawings Is returned “Approved” Mina Abdullah- Kuwait, Ras Al Khaimah- UAE,
or “Approved as Noted”. Resubmittal of Hyderabad and Haridwar- India. Combined
approval drawings will be only at the request Kirby has a total production capacity of
of the client, otherwise Kirby will incorporate 425,000 MT per year. Kirby has been ISO
the noted amendments in the final building 9001:2008 certified company since 2010.
installation drawing when issued for
In the Middle East and African region, Kirby
construction.
manufactures Pre-Engineered and Structural
Drawings submitted for approval constitute Steel out of two manufacturing locations in
an integral part of the contract between the Ras Al-Khaimah, UAE and Mina Abdullah, Kuwait.
client and Kirby. The contents of the Approval In Southeast Asia, a manufacturing plant in Ho
Building installation drawings are intended Chin Minh City, Vietnam.
specifically for the job at hand; and therefore,
Kirby’s sales and distribution network includes
they supersede, in case of contradiction, any
24 offices in the GCC countries (Kuwait, Saudi
other information published for general use.
Arabia- Riyadh, Dammam and Jeddah, Qatar,
Anchor bolt plans will be issued “For Oman, Bahrain and Dubai and Abu Dhabi in
Construction” after receipt of signed approval the UAE), the Middle East, and Africa.
drawings. Only drawing stamped “For
Construction” shall he used for setting anchor
bolts and building installation.

2
Kirby has designed, manufactured and The group’s major areas of activity are trading
supplied more than 50,000 steel buildings and distribution of consumer electronics,
and established its presence as an industry- food and consumables, automotive vehicles
leading steel structures company. Kirby and products, industrial manufacturing,
delivers customized pre-engineered and steel engineering, technology, travel, shipping
structures to a broad range of customers and transportation services, advertising,
in sectors such as Oil & Gas, Infrastructure, insurance and contracting.
Industry and Commercial building applications.
Furthermore each of Alghanim’s separate
Kirby’s customer base covers thousands of businesses employs operating autonomy
satisfied clients including General Motors, with its own general manager, marketing
AT&T, PepsiCo and Coca Cola, Ministries of managers and finance managers. Corporate
Defense, Oil companies and Petrochemical policy matters remain centrally controlled
projects and other key international and direction is provided through strategic
organizations over the world. business planning processes, quarterly
operating review meetings and long term
Kirby Building Systems is a wholly-owned forecasting.
subsidiary of Alghanim Industries. Alghanim
Industries has consistently maintained its Multinational in both outlook and operation,
position as a leading private sector trading Alghanim Industries has offices in countries
and industrial group both in Kuwait and the that span four continents. The diverse
GCC during the past 60 years. It is a privately nationalities of the employees contribute
owned, professionally managed holding to the company’s strength and widen
company. The executive management is its perspective. Alghanim Industries has
composed of professionals with international
successfully fused progressive business
education and experience in varying areas
procedures, local market place requirements
of expertise. Overall, with the company’s
and international resources.
wholly owned subsidiaries, joint ventures and
associations, Alghanim Industries employs
over 8,000 people from over 40 different
countries around the world.

3
1.3 DEFINITION OF TERMS

ACCESSORY - BASE CHANNEL -

A building component added to a basic Kirby A light gauge cold formed channel which
structure, such as door, window, ventilator, etc. replaces the base angle when liner panel or
AISI - double sheeted partitions are required.
American Iron and Steel Institute BASE PLATE -
AISC - A plate attached to that portion of a beam or
American Institute of Steel Construction column that rests on the supporting surface,
ALUMINIZED - usually secured with anchor bolts.
Aluminum coated steel BAY (END) -
ANCHOR BOLTS - The distance between first interior frame and
Bolts used to anchor structural members to a inside of endwall panel.
foundation or other support BAY (INTERIOR) -
ANCHOR BOLT DRAWINGS - The distance between center lines of two
Show the size, location and projection of all rigid frames or transverse bents, measured
anchor bolts for the components of the metal parallel to the ridge.
building system, the length and width of the BEAM -
foundation (which may vary from the nominal A structural member usually horizontal
size of the metal building system) and column carrying vertical loads which is ordinarily
reactions(magnitude and direction). The subjected to bending.
maximum base plate dimensions may also be BEAM, CANTILEVER -
shown. A beam supported at one end only and free
APPROVAL DRAWINGS - at the other; such as brackets, canopies,
Include anchor bolt drawing, framing plans, flagpoles.
elevations and sections through the building BEAM, CONTINUOUS -
for approval of the buyer / or his consultant. A beam which has more than two points of
ASSEMBLY - support, (continuous span).
Two or more components welded together. BEAM, SIMPLE -
AUTOMATIC WELDING - A beam simply supported at both ends,
A welding procedure utilizing a machine to theoretically with no rotational end restraint.
make a weld. BEARING FRAME -
AUXILIARY LOADS - Frame made up of beams and columns so
All dynamic live loads required by the contract constructed that joints are not capable of
documents such as cranes and material transferring moment due to lateral
handling systems. loads, usually used at sheeted endwalls of
A. W.S. - a metal building, and when not subject to
American Welding Society auxiliary loads or to further building
AXIAL FORCE - expansion.
A force tending to elongate and shorten a BILL OF MATERIALS -
member. A list of items or components used for
BC- fabrication, shipping, receiving and accounting
Beam and Column building. A single gable, rigid purposes.
frame building with interior columns. BIRD SCREEN -
BASE ANGLE Wire mesh used to prevent birds from entering
A continuos angle secured to foundation to the building through ventilators and louvers.
support wall panel

4
BLIND RIVET- forming a connection. Sometimes called a splice
A small headed pin with expandable shank for plate or bolted end plate.
joining light gauge metal. Typically used to attach BY-FRAMED WALL -
flashing, gutter, etc. A wall framing system where the girts are
BRACE RODS, ANGLES - mounted on the outside of the column.
Braces used in roof and walls to transfer BUTTERFLY CANOPY -
loads, such as wind loads, seismic and crane A free standing, single column supporting roof
longitudinal load to the foundation. structure, having a valley gutter at the centerline
BRACKET - of the building, and the two outer edges of the
A structural support projecting from a wall or roof projecting upwards.
column on which to fasten another structural “C” SECTION -
member. Examples are canopy brackets, lean-to A member cold formed from steel sheet in the
brackets and crane runway brackets. shape of a block “C” with or without lips at edge
BRIDGE CRANE - of flanges.
A load lifting system consisting of a hoist which CALORIE -
moves laterally on a beam, girder or bridge which Quantity of heat required to raise the
in turn moves longitudinally on a runway made temperature of one gram of water through 1°C (1
of beams and rails. Loads can be moved to any BTU = 252 Calories)
point within a rectangle formed by the CAMBER -
bridge span and runway length. Upward curvature of a beam in the plane of its web
BRIDGING - before loading, to offset an anticipated deflection
Structural members used to give weak axis when load is applied
stability to open web joists. CANOPY -
BRITISH THERMAL UNIT (BTU) - A projecting beam that is supported and restrained at
one end only.
That amount of heat required to raise the
CAPILLARY ACTION -
temperature of one pound (0.454 kg.) of water
That action which causes movement of liquids when
by 1°F (0.560°C). in contact with two adjacent surfaces such as panel
BUILDER - sidelaps.
A general contractor or sub-contractor CAP PLATE -
responsible for providing and erecting pre- A plate located at the top of a column or end of a
engineered buildings. beam for capping the exposed end of the member.
BUILDING CODE - CAULK -
Regulations established by a recognized agency See sealant.
describing design loads, procedures and CHANNEL- HOT ROLLED -
construction details for structures. A “c” shaped member formed while in a semi-molten
BUILT-UP ROOFING - state at the steel mill to a shape having standard
A roof covering made up of alternating layers of dimensions and properties.
tar and asphaltic materials (mostly used for flat CLIP -
A plate or angle used to fasten two or more members
roofs).
together.
BUILT-UP SECTION -
CLOSURE STRIP -
A structural member, usually an “ I “ section, A resilient strip formed to the contour of ribbed
made from individual flat plates welded together. panels and used to seal around openings created
BUTT PLATE - by metal panels joining other components and at
The end plate of a structural member usually horizontal and vertical corners of a building.
used to rest against a plate of another member in COLD FORMING -

5
The process of using press brakes of rolling mills
to shape steel into desired cross sections at room CURTAIN WALL -
temperature. Perimeter wall panels which carry only their own
COLLATERAL LOAD - weight and wind load.
All additional dead loads required by the contract
DAMPER -
documents other than the weight of the metal
building system such as sprinklers, mechanical and
A baffle used to open or close the throat of
electrical systems and ceilings. ventilators.
COLUMN - DEAD LOAD -
A main member used in a vertical position on a The self weight of the metal building system
building to transfer loads from main roof beams, construction, such as framing, and covering
trusses, or rafters to the foundation members.
COMPONENT - DEFLECTION -
A part of a metal building system. The displacement of a structural member or
COMPRESSION - system under load.
The act of causing material to contract or shorten.
DESIGN LOADS -
CONCENTRATED LOAD -
A load applied on a member at a point or over a very
The loads expressly specified in the contract
short distance. documents which the metal building system is
CONTINUITY - designed to safely resist.
The terminology given to a structural system denoting DIAGONAL BRACING -
the transfer of loads and stresses from member to See Brace Rods
member as if there were no connections. DIAPHRAGM ACTION -
CONTRACT DOCUMENTS - The capacity of a roof, wall, or floor system to
The documents which define the responsibilities resist load in its own plane. (As building roof
of the parties involved in the sale, design, supply and wall systems resisting longitudinal wind load
and building installation ( if any ) of a metal building
without rod bracing).
system. Such documents normally consist of a
contract and specification. Plans may be included.
DOOR GUIDE -
CORNER TRIM - An angle or channel guide used to stabilize or
Preformed sheet metal trim used to close the junction keep plumb a sliding or rolling door during its
of sidewall and endwall sheets. operation.
COVERING - DOWNSPOUT -
The exterior metal roof and wall paneling of a metal A conduit used to carry water from the gutter of
building system. a building.
CRANE - DRIFT PIN -
A machine designed to move material by means of a A tapered pin used during building installation to
hoist.
align holes in steel members to be connected by
CRANE RAIL -
A track supporting and guiding the wheels of a bridge
bolting ( also called spud wrench).
crane or trolley system, and mounted on crane runway EAVE -
beams. The line along the sidewall formed by the
CRANE RUNWAY BEAM - intersection of the planes of the roof and wall.
The member that supports a crane rail and is EAVE GUTTER -
supported by columns or rafters depending on See Gutter.
the type of crane system. On under hung bridge EAVE HEIGHT -
cranes, runway beams also act as crane rail. The vertical dimension from bottom of column
CURB - base plate to top of the eave strut.
A raised edge on a concrete floor slab. EAVE STRUT -

6
A structural member located at the eave of a
building which supports roof and wall paneling. FIELD -
Also member which transmits longitudinal wind The “job site”, “building site” or general
forces on endwall from roof brace rods to wall marketing area.
brace rods. FILLER STRIP -
ELASTIC DESIGN - See “Closure”.
A design concept utilizing the proportional FIXED BASE -
behavior of materials when all stresses are A column base that is designed to resist rotation
limited to specified allowable values of the yield as well as horizontal or vertical movement
stress of the materials. (develops bending moment).
END FRAME - FLANGE -
A frame located at the end wall of a building The projecting portion of a structural member
which supports the loads from a portion of the ( C, I, H shapes ).
end bay. FLANGE BRACING -
END WALL - A bracing member used to provide lateral
An exterior wall which is perpendicular to the support to the compression flange of a beam,
ridge of the building. girder or column.
END WALL COLUMN - FLASHING -
A vertical member located at the end wall of a See Trim.
building which supports the girts. FLUSH FRAMES -
END WALL EXTENSION - A wall framing system where the outside flange
The projection of the roof past the endwall. of the girts and columns are flush.
BUILDING INSTALLATION - FOOTING -
The on-site assembling of fabricated A pad or mat, usually of concrete, located under
components to form a complete structure. a column, wall or other structural member, that
BUILDING INSTALLATION DRAWINGS - is used to distribute the loads from that member
A package of drawings, issued for construction into the supporting soil.
and includes anchor bolt drawings and roof and FOUNDATION -
Wall framing (building installation) plans that The substructure which supports a building or
identify individual components and accessories other structure.
furnished by Kirby in sufficient detail to permit FRAME -
proper building installation of the building. Primary structural members made up of columns,
EXPANSION JOINT - rafters which support secondary framing.
A break or space in construction to allow for FRAMED OPENING -
thermal expansion and contraction of the Jambs, headers and flashing which surround an
materials used in the structure. opening in the wall of a metal building.
FABRICATION - GABLE -
The manufacturing process performed in a The triangular portion of the endwalllocated
plant to convert raw material into finished metal above the elevation of the bottom of eave strut.
building components. The main operations are GABLE ROOF -
cold forming, cutting, punching, welding, cleaning A ridged roof that terminates in gables.
and painting. GAGE -
FASCIA - Distance between holes along transverse axis of
A structural framing member projecting from the plate.
face of a wall for decorative purposes. GAUGE -

7
Numerals referring to thickness of thin sheeting The deep-end portion of a column or rafter
materials. No direct mathematical relation designed to accommodate the higher bending
between gauge number and moments at such point. (Usually occurs at the
thickness; the higher the gauge number, the connection of column and rafter). Also referred
thinner the sheeting material. to as Knee.
GALVANIZED - HAUNCH BRACE -
Steel coated with Zinc for corrosion resistance. A diagonal brace from the intersection of the
GIRDER - column and rafter section of the rigid frame
A main horizontal or near horizontal structural to the eave to prevent lateral buckling of the
member that supports vertical loads. It may haunch.
consist of several pieces. HEADER -
GIRT - The horizontal framing member located at the
A horizontal structural member that is attached top of a framed opening.
to sidewall or endwall columns and supports HEM -
panelling. Edge of trim or flashing turned 180 degrees on
GLAZE OR GLAZING - itself for increased strength.
The process of installing glass in windows and HIGH STRENGTH BOLTS -
doors. Any bolt made from steel having a tensile
GRADE - strength in excess of 100,000 pounds per
The term used when referring to the ground square inch(690 MPa).
elevation around a building. HIGH STRENGTH STEEL -
GRADE BEAM - Structural steel having a yield stress in excess of
A concrete beam around the perimeter of a 36,000 pounds per square inch (250 MPa).
building. HINGED BASE -
GROUT - A column base which is designed to resist
A mixture of cement, sand and water used horizontal and vertical movement but not
to fill cracks and cavities. Sometimes used rotation. Also referred to as pinned base.
under base plates or leveling plates to obtain HIP ROOF -
uniform bearing surfaces. Not normally used in A roof which rises by inclined planes from all four
conjunction with metal building systems. sides of a building. The line where two adjacent
GUSSET PLATE - sloping sides of a roof meet is called the Hip.
A steel plate used to reinforce or connect HOIST -
structural elements. A mechanical lifting device usually attached to a
GUTTER - trolley which travels along a bridge, monorail or
A light gauge metal member at an eave, valley or jib crane. May be chain or electric operated.
parapet designed to carry water from the roof to HOOD -
downspouts or drains. Metal flashing to cover exterior sliding door track
“H” Section - along the full length of the door header.
A steel member with an H cross section. HOT ROLLED SHAPES -
HAIRPIN - Steel section (angles, channels, S-shapes,
U-shaped reinforcing steel or round bar hooked W-shapes, etc.) which are formed by rolling mills
around anchor bolts and embedded in concrete while the steel is in a semi-molten state.
floor mass, to transfer the horizontal thrust at IMPACT LOAD -
the base of the rigid frames to the concrete floor. A dynamic load resulting from the motion of
HAUNCH - machinery, elevators, crane ways, vehicles, and

8
other similar moving forces. See Auxiliary Loads. Standard corrugated panel used for roof, liner
IMPACT WRENCH - and soffits.
A pneumatic device used to tighten nuts on KIRBY-WALL PANELS -
bolts. Standard corrugated panel used for exterior
INSULATION - surface of walls.
Any material used in building construction to KNEE BRACE -
reduce heat transfer. A diagonal brace designed to resist horizontal
INTERNAL PRESSURE - loads usually from wind or moving equipment
Pressure inside a building which is a function connecting the column to a beam by forming a
of wind velocity and number and location of rigid triangle.
openings. LEAN - TO -
JACK BEAM - A structure such as a shed, having only one
A beam used to support another beam or rafter column and depending upon another structure
or truss and eliminate a column support. for partial support.
JAMB - LEVELING PLATE -
The vertical framing members located at the A steel plate used on top of a foundation or
sides of wall openings. other support on which a structural column can
JIB CRANE - rest.
A cantilevered boom or horizontal beam with LINER PANEL -
hoist and trolley. This lifting machine may pick up A metal panel attached to the inside flange of
loads in all or part of a circle around the column the girts, or the purlin.
to which it is attached. LINTEL -
JIG - A beam: concrete, steel or stone, in masonry
A device used to hold pieces of material in a walls, placed above doors, openings or windows
certain position during fabrication. to support masonry above.
JOIST - LIP -
Open web beam for supporting the floor or roof, A stiffener at the edge of flange of cold formed
made of continuous angular top and bottom members.
chords which are connected with vertical and LIVE LOAD -
diagonal angles. For open web joist, the joist can Any moving or variable load which the structure
be built-up or hot rolled. must support due to the use or occupancy of the
KICK-OUT - building.
An extension attached to the bottom of a LOUVER -
downspout to direct water away from a wall. Also An opening provided with fixed or movable,
referred to as Turn-Out or Elbow. slanted fins to allow flow of air.
KILO-CALORIE (K.CAL) - MAIN MEMBERS -
Quantity of heat required to raise the The main load carrying members of a structural
temperature of one Kilogram of water by 1°c. system including columns,end wall posts, rafters
KILOGRAM - and other main support members.
Metric Unit of Mass. ( 1 Kg 2.2 Ibs). MANSARD FASCIA -
KIP - An imperial unit to measure force equal to A tilted fascia projected from the wall and
1000 pounds equivalent to 4.4 kilo newtons. extended above roof line to form as decorative
KIRBY-DECK PANEL - appearance and to hide the roof line.
Standard corrugated panel used for floor deck. MASONRY -
KIRBY-RIB PANEL - Construction materials such as bricks, concrete

9
blocks, ceramic blocks, and concrete. Raised gable or triangular portion of main
MASTIC - building at ridge location to allow lighting or
Material used to seal cracks, joints and laps. ventilation at vertical sides of monitor.
MBMA - MONOLITHIC CONSTRUCTION -
Metal Building Manufacturers Association. A method of pouring concrete grade beam
MBMA CODE OF STANDARD PRACTICES - and floor slab together to form the building
A listing of normal conditions that apply to the foundation without forming and pouring each
sale, design, fabrication and building installation separately.
of a metal building system. MONORAIL -
METAL BUILDING SYSTEM - A single rail support for a material handling
A metal building system consists of a group of system. Normally a standard hot rolled I-Beam.
coordinated components, including structural MPa -
members, exterior covering panels, fastening Mega Pascal
devices and accessories, which have been MULLION -
designed for specific loads, which will work Vertical member connecting two windows
together compatibly and which have been located side by side.
engineered so that they may be mass produced MULTI-SPAN BUILDING -
and assembled in various combinations, or in a Building consisting of more than one gable
combination with various collateral materials, across the width that may or may not have
to provide an enclosed or partially enclosed interior columns within each gable.
structure. NEWTON -
METER - Metric unit of force (1 N = O.2248 Ibf)
Metric unit of length (1 m = 3.28 ft.) PANEL -
MEZZANINE - Gauge metal sheets usually with ribbed
An intermediate floor within a metal building configuration and used for Roof and Wall skins
used for offices or storage, may or may not be PARAPET -
connected to main frame building, and consisting That portion of the wall which extends vertically
of beams, columns, joists, deck and edge angles above the roof line to form a fascia type
to receive reinforced concrete. appearance.
MICRON - PARTITION -
Equivalent to 0.001 Millimeter. An interior dividing wall.
MIL - PASCAL -
Equivalent to 0.001 inch Metric unit of stress or pressure, force per unit
MOMENT - area (N /M2)
The tendency of a force to cause rotation or PEAK -
bending about a point or axis. Force times a The uppermost point of a gable.
distance (Torque). PEAKPANEL -
MOMENT CONNECTION - A” Kirby-Rib” panel located at the building peak
A connection designed to transfer moment conforming to roof slopes.
as well as axial and shear forces between PEAK SIGN -
connecting members. A sign attached to the peak of the building
MOMENT OF INERTIA - at endwall showing Kirby as the building
A physical property of a member which helps manufacturer.
define strength and deflection characteristics. PERSONNEL DOOR -
MONITOR - A door used by personnel for access to and exit

10
from a building. ROOF SNOW LOAD -
PIECE MARK - The load induced by the weight of snow on the
A number given to each separate part of the roof of the structure.
building for building installation identification. ROPESEAL -
Also called mark number and part number. (See “Sealant”).
PIER - PRE-ENGINEERED BUILDING -
A concrete structure designed to transfer A building structure that consists of pre-
vertical load from base of column to a footing. engineered, pre-fabricated factory components
PIG SPOUT - that are combined together and
A sheet metal section designed to direct the flow engineered structurally.
of water out through the face of the gutter rather PRE-PAINTED COIL -
than through a downspout. Coil metal which received a paint coating prior to
PILASTER - the forming operation.
A reinforced or enlarged portion of a masonry PRESS BRAKE -
wall to provide support for roof loads or lateral A machine used in cold-forming metal sheet or
loads on the wall. strip into desired cross section.
PINNED BASE - PRESTRESSED CONCRETE -
A column base that is designed to resist Concrete in which the reinforcing cables, wires
horizontal and vertical movement, but not or rods in the concrete are tensioned before
rotation. there is load on the member, holding the
PIN CONNECTION - concrete in compression for greater strength.
A connection designed to transfer the axial and PRISMATIC BEAM -
shear forces between connecting members, but A beam with uniform rectangular cross section.
not moments. PURLIN -
PITCH - A horizontal structural member attached to the
Distance between holes along longitudinal axis of main frames which supports roof panels.
plate. RF -
PLASTIC DESIGN - A single gable rigid frame building.
A design concept based on multiplying the actual RAFTER -
loads by a suitable load factor using the yield The main beam of the frames supporting the
stress as the maximum stress in any member. roof system.
PLASTIC PANELS - RAKE -
See Translucent Light Panels. The intersection of the plane of the roof and the
PONDING - plane of the endwall.
The gathering of water at low or irregular areas RAKEANGLE -
on a roof. Angle fastened to purlins at rake for attachment
POP RIVET - of endwall sheets.
See” Blind Rivet”.’ RAKETRIM -
PORTAL FRAME - Sheet metal flashing used to cover the
A rigid frame structure so designed that it offers intersection of the roof and the endwall of a
rigidity and stability in its plane. It is used to building.
resist longitudinal loads where diagonal bracing REACTIONS -
is not permitted. (also “Wind Bent”). The resisting forces at the column bases of a
POST (END POST) - frame, holding the frame in equilibrium under a
See” End Wall Column”. given loading condition.

11
REINFORCING STEEL - A tension member used to limit the deflection of
The steel bars placed in concrete to help carry a girt or purlin in the direction of the weak axis.
the tension, compression and shear stresses, as SANDWICH PANEL -
well as temperature stresses. A panel assembly used as covering; consists of
RIDGE - an insulating core material with inner and outer
Highest point on the roof of the building which skins.
describes a horizontal line running the length of SAND TRAP LOUVER -
the building. A type oflouver having fixed C-shaped sections
RIDGE CAP - placed altenatively in a vertical configuration
A transition of the roofing materials along the allowing sand and heavy dust separation.
ridge of a roof. SCREEDING -
RIGID CONNECTION - The process of striking off the excess concrete to
See” Moment Connection”. bring the top surface of the concrete to proper
RIGID FRAME - finish and elevation.
A structural frame consisting of members joined SEALANT -
together with rigid (or moment) connections so Any material which is used to seal cracks, joints
as to render the frame stable with respect to the or laps.
design loads, without the need for bracing in its SECTION MODULUS -
plane. A physical property of a structural member. It
ROLL-UP DOOR - is used to design and basically describes the
Door that is supported on a shaft or drum and a bending strength of a member.
vertical track. SEISMIC LOAD -
ROOF COVERING - The assumed lateral load acting in any horizontal
The exposed exterior roof skin consisting of direction on a structural system due to the
panels or sheets, action of an earthquake,
ROOF LIVE LOAD - usually a proportion of dead load.
Those loads induced by the use and occupancy SELF DRILLING SCREW -
of the building, not including wind load, seismic A fastener which combines the functions of
load, dead load or snow load. drilling and tapping. It is used for attaching
ROOF OVERHANG - panels to purlins and girts.
A roof extension beyond the endwall or sidewall SELF TAPPIN G SCREW -
of a building. A fastener which taps its own threads in a pre-
ROOF PITCH - drilled hole. It is for attaching panels to purlins
Ratio of rise to total width of a single slope. and girts, for connecting trim, flashing, and panel
ROOF SLOPE - side lap.
The angle that a roof surface makes with the SHEAR -
horizontal. Usually expressed in units of vertical The force tending to make two contacting parts
rise to 10 units of horizontal run. slide upon each other in opposite directions
SS- parallel to their plane of contact.
Single Slope clear span buildings SHEET NOTCH -
SV- A notch or block formed along the outside edge
Space Saver building - a single gable clear span of the foundation to provide support for the wall
with straight columns and flush girts to offer panels and serve as a closure along their bottom
maximum clearances. edge,
SAG ROD, STRAP, OR ANGLE - SHEETING ANGLE -

12
An angle used to support sheeting. support condition for a beam, girt, purlin, etc,
SHIM - which offers no resistance to rotation at the
A piece of steel used to level base plates or supports; opposite to continuous.
square beams. SINGLE SLOPE -
SHIPPER - A slope in one plane. The slope is from one wall
A list that enumerates by part number or to the opposite wall.
describes each piece of material or assembly SINGLE SPAN -
to be shipped. Also called talley sheet or bill of A building or structural member without
materials. intermediate support.
SOLDIER COLUMN - SKYLIGHT -
A column in sidewalls, outside the main frame A translucent panel. A roof accessory to admit
lines, located in extended bays to support light, made of fiber glass reinforced polyester to
sidewall girts framed at top with the profiles of Kirby standard sheeting profiles.
jack beam to adjacent two main frames. SLIDING DOOR -
SHOP PRIMER PAINT - A single or double leaf door which opens on a
The initial coat of primer paint applied in the horizontal track by means of overhead trolleys.
shop. SLIDING FOLDING DOORS -
SHOULDER BOLT - A form of manual sliding doors where-in
A fastener used to attach wall and roof paneling the doors are made of leaves suspended and
to the structural frame. It consists of a large connected in a manner so as to fold
diameter shank and a small diameter stud. The against each other.
shank provides support for the panel rib. SOFFIT -
SHOT PIN - A metal panel which covers the underside of an
A device for fastening items by the utilization of overhang, canopy, or fascia.
a patented device that uses powdered charge to SOIL PRESSURE -
imbed the item in the concrete and/ or steel. The load per unit area a structure will exert
SI - through its foundation on the soil.
The International symbol for the metric unit used SPALL -
by the United States (Le Systeme International A chip or fragment of concrete which has
d’Unites). chipped, weathered or otherwise broken from
SIDE LAP FASTENER - the main mass of concrete.
A fastener used to connect panels together at SPAN -
the side lap. The out-to-out of steel lines for building frames,
SIDE WALL - or the distance between supports of beams for
An exterior wall which is parallel to the ridge of secondary members.
the building. SPLICE -
SIDE WALL OVERHANG - A connection in a structural member.
A projection of the roof past the sidewall. STAINLESS STEEL -
SILL - An alloy of steel which contains a high
The bottom horizontal framing member of an percentage of chromium. Also may contain nickel
opening such as a window or door. or copper.
SILL ANGLE - STIFFENER -
See” Base Angle” A member used to strengthen a plate against
SIMPLE SPAN - lateral or local buckling. Usually a flat bar welded
A term used in structural analysis to describe a perpendicular to the longitudinal axis of the

13
member. expressed as BTU per hour per square foot per
STIFFENER LIP - inch thickness per °F.
A short extension of material at an angle to the THERMAL CONDUCTANCE (C) -
flange of cold formed structural members, which The rate of heat flow, in BTU’s per hour, through
adds strength to the member. a square foot of material of specified thickness
STILES - whose surfaces have a temperature differential
The vertical side members off ramed and of 1°F.
paneled doors. THERMAL RESISTANCE (R) -
STRESS - Resistance to heat flow. The reciprocal of
A measure of the load on a structural member conductance (C).
in terms of force per unit area (kips per sq. in.) THERMAL TRANSMITTANCE (U) -
(MPa) . The rate of heat transmission in unit time
STRUT - through unit area of an assembly of materials
A brace fitted into a framework which resists for unit temperature difference,
axial compression forces. expressed as BTU per hour per square foot
STRUT PURLIN - per °F. This is also referred to as the overall
An additional purlin in braced bays located close coefficient of heat transfer.
to the purlin at the intersection of roof brace THROAT -
rods and the frame rafter as required by design. Minimum width of ventilator air inlet.
STUD - THRUST -
A vertical wall member to which exterior or The horizontal component of a reaction
interior covering or collateral material may be TIE -
attached. May be either load bearing or non- A structural member that is loaded in tension
Ioad bearing. TORQUE WRENCH -
SUCTION - A wrench containing an adjustable mechanism
A partial vacuum resulting from wind loads on for measuring and controlling the amount of
a building which cause a load in the outward torque or turning force to be exerted, often used
direction. in tightening nuts and high strength bolts.
TAPERED MEMBER - TRANSLUCENT LIGHT PANELS -
A built-up plate member consisting of flanges Translucent plastic panels used to admit sunlight.
welded to a variable depth web. TRANSVERSE -
TEMPERATURE REINFORCING - The direction perpendicular to the ridge.
Light weight deformed steel rods or wire mesh TRIBUTARY AREA -
placed in concrete to resist possible cracks from The area which contributes load to a specific
thermal expansion or contraction. structural component.
TENSILE STRENGTH - TRIM -
The longitudinal pulling stress a material can The light gauge metal used in the finish of a
bear without tearing apart. building especially around openings and at
THERMAL BLOCK - intersection of surfaces. Often referred to as
A spacer of low thermal conductance material. flashing.
THERMAL CONDUCTIVITY (k) - TRACK -
The rate of heat transmission by conduction A metal guide for moving components; consisting
in unit time through unit area of an infinite of angles or channels, with fastenings, ties, etc.
slab in a direction perpendicular for a crane way, monorail or slide door.
to the surface for unit temperature difference, TRUSS -

14
A structure made up of three or more members, than its own weight.
with each member designed to carry a tension or WALL COVERING -
compression force. The entire structure in turn The exterior wall skin consisting of panels or
acts as a beam. sheets.
TURNOUT - WALL, NON BEARING -
See” Kickout “. Wall capable of supporting its own weight only.
TURN-OF-THE-NUT METHOD - WEB -
An approved method for pre-tensioning high That portion of a structural member between
strength bolts. The nut is turned from the snug- the flanges.
tight position, corresponding to a few blows of an WEB MEMBER -
impact wrench or the full effort of a man using an A secondary structural member vertical or
ordinary spud wrench, the amount of rotation diagonal interposed between the top and bottom
required being a function of the bolt diameter chords of a truss.
and length. WICKET DOOR -
UNIFORM LOAD - An access door within one leaf of a sliding door.
A load which is evenly spread over a large area of WIND BENT -
a framing system. See” Portal Frame”.
UPLIFT - WIND COLUMN -
Wind load on a building which causes a load in A vertical member supporting a wall system
the upward direction. (See “Suction”) designed to withstand horizontal wind loads
VALLEY GUTTER - usually at end walls.
A channel used to carry off water from the “V” of WIND LOAD -
roofs of multi-gabled buildings. The load caused by the wind blowing from any
VENTILATOR - horizontal direction.
An accessory, usually used on the roof, that “Z” SECTION -
allows the air to pass through. A member cold formed from steel coil in the
WAINSCOT - shape of a block “Z”.
Wall material, used in the lower portion of a wall, ZINC-ALUMINIUM COATED -
that is different from the material in the rest of Steel coated with zinc and aluminum for
the wall. corrosion resistance
WALL, BEARING -
Wall capable of supporting a vertical load, other

15
2 : SPECIFICATIONS
2.1 GENERAL

2.1.1 Scope:
building shall consist of single straight columns fixed
2.1.1.1 The standard building scope of supply shall include at base at each frame with a single cantilever roof
the structural framing, metal roofing & siding,bracing, sloping towards the column.
doors, windows. insulation, hardware, fasteners, sealants
and any other component parts for the metal building as 2.1.2.7 Lean-To Buildings: ‘LT’( Lean-To). The building
specified or shown on the drawings. shall have a single slope roof and connected on the
high side to the main building on which it depends for
2.1.1.2 All buildings shall have diagonal cable bracing partial support. The roof slope shall be either 1/10 or
in the roof, side walls; common walls between main 0.5/10 matching with the main building roof slope and
building and Lean-to’s, between interior columns wall sheeted with flush girts.
under valley lines for multi span type buildings, unless
otherwise stated in KBS offer. 2.1.3 Building nomenclature:
2.1.1.3 In case of discrepancies, the provisions of the
Final Order Acknowledgement Form shall govern 2.1.3.1 The building “width” and “length” shall be
unless agreed by Kirby Building Systems in writing. measured from inside to inside of wall covering.
2.1.3.2 The building eave height shall be
2.1.2 Standard building description: measured from bottom of primary frame base
plate to top of the eave strut. The top of the
2.1.2.1 Clear-span, Rigid Frame Buildings: “RF” ( Rigid eave strut is the point of intersection between
Frame ). The building shall be a single gable, clear the inside surfaces of the wall and roof covering.
span, tapered column. pin base, by-frame girts, 1/10
roof slope, rigid frame type. 2.1.3.3 The bay spacing shall be measured as
follows:
2.1.2.2 Clear-span Spacesaver Buildings: “ SV “ (
Spacesaver ). The building shall be a single gable, a. Interior bays from center-line to center-line of
clear span, straight column, pin base, flush framed interior frames.
girts, 0.5/1 0 roof slope, rigid frame type.
b. End bays from inside of Endwall sheets to
2.1.2.3 Beam and Column Buildings: “ BC “ ( Beam center-line of first interior frame.
and Column ). The building shall be a single gable,
tapered column, pin base, by-frame girts, 1/10 roof
slope, rigid frame type, supported by intermediate
2.1.4 Drawings & calculations:
columns as shown on drawings.
The following shall be provided free of charge in
2.1.2.4 Clear Span, Single Slope Buildings: ‘SS’ ( Single 3 sets each after the receipt of the Final Order:
Slope). The buildings shall have a single slope roof
with tapered columns pinned at base and straight 2.1.4.1 Anchor bolt setting plans will be provided by
rafters. The roof slope shall be 0.5/10 and sidewalls Kirby Building Systems or the franchised builder.
sheeted with by-framed girts.
2.1.4.2 Building installation drawings will be
2.1.2.5 T-Canopy Buildings: ‘T-CAN’ ( T-Canopy ). The provided by Kirby Building Systems
building shall consist of single straight columns fixed
at base at each frame with a double cantilever roof 2.1.4.3 Preliminary drawings, design calculations
sloping towards the center columns. and/ or letter of Certification for the structural
framing and covering panels, signed by a
2.1.2.6 L-Canopy Buildings: ‘L-CAN’( L-Canopy). The Professional Engineer, may be submitted for
client’s approval upon request.
16
2.2 DESIGN

2.2.1.1 All structural steel sections and welded 2.3.1.2 All framing members shall be cleaned by
plate members shall be designed in accordance power or hand-wire brushing to remove all dirt,
with the applicable sections, relating to design grease, oil, loose mill scale, weld slag, flux deposit
requirements and allowable stresses, of the and other foreign matter, and given one shop
latest edition of the American Institute of Steel coat of red oxide, air drying, phenol modified
Construction “Specification for the Design, alkyd resin primer to a nominal dry film thickness
Fabrication and Building installation of the of 25 microns.
Structural Steel for Buildings.”
2.3.2 Primary members :
2.2.1.2 All light-gauge, cold formed, structural
members and covering shall be designed in 2.3.2.1 Primary structural framing shall refer to
accordance with the applicable sections, relating the transverse rigid frames, lean-to rafters and
to design requirements and allowable stresses, columns canopy rafters, interior columns (beam
of the latest edition of the American Iron and and column frames), bearing frame rafters and
Steel Institute “ Specification for the Design of corner columns, and endwall wind columns.
Cold Formed Steel Structural Members”. a. Members fabricated from plate or bar stock
shall have flanges and webs joined on one side
2.2.2 Design loads: of the web by a continuous welding process.
This plate or bar stock shall have a minimum
2.2.2.1 The design loads shall be as stated in part I ( yield strength of 345 MPa (50,000 psi) and will
Building description of Kirby Building Systems offer ) conform to the physical specifications of ASTM
A-572 (Grade 50) or equivalent.
2.2.2.2 Loads are applied as follows :
a. Seismic loads shall be applied in accordance to b. Members fabricated by cold forming process
International Building Code ( IBC ) shall have a minimum yield strength of 345 MPa
(50,000 psi) and will conform to the physical
b. Other loads applications :. specifications of ASTM A653 (Galvanised G90)
The minimum loads required in applying on or equivalent.
the structure in order to ensure the safety
c. Members fabricated from hot rolled structural
and serviceability of the building shall be in
shapes shall have a minimum yield strength
accordance to the International building Code
of 250 MPa (36,000 psi) and will conform to
( IBC ) latest edition.
the physical specifications of ASTM A-36 or
2.2.2.3 Basic design load combinations shall be equivalent.
in accordance to IBC latest edition. Other load
combination as applicable per MBMA code. d.Beam and Column interior columns will be
fabricated from tube sections according to
2.3 STRUCTURAL FRAMING ASTM A500 Grade C, which have a minimum
yield strength of 345 MPa (50,000 psi)
2.3.1 General:
2.3.3 Secondary members:
2.3.1.1 All framing members shall be shop
fabricated or bolted field assembly, unless 2.3.3.1 Secondary structural framing shall refer to
otherwise noted on building installation drawing. purlins, girts, eave struts, wind bracing, flange
bracing, base angles, clips and other

17
miscellaneous structural parts. with the applicable sections, relating to design
requirements and allowable stresses, of the
a. Purlins, girts and eave struts shall be cold latest editions of the American Welding Society
formed from steel which has a minimum yield “Structural Welding Code”.
strength of 345 MPa (50,000 psi) and will
conform to the physical specifications of ASTM
A-653 (Grade 50) or equivalent. 2.4 ROOF AND WALL COVERING
1. Purlins and girts shall be roll formed Z sections, 2.4.1 General:
200 mm deep with 64mm flanges. Each flange
shall have a 16mm stiffening lip formed at 45° to 2.4.1.1 Typical roof, wall and liner panels shall be
the flange. color coated, 26 gauge, galvalume or galvanized
coated steel, ribbed panels. (Other materials and
2. Eave struts are 200mm deep with a 105mm
thickness available upon request).
wide top flange, a 117.5mm wide bottom flange,
both are formed parallel to the roof slope. Each
flange has a 22.5mm stiffener. 2.4.2 Panel materials:

b .Cable bracing shall have a minimum tensile 2.4.2.1 Base material for color coated galvanized
force of 119 kn and will conform to the physical or galvalume substrate steel panels shall have a
specifications of ASTM A475 or equivalent. minimum yield strength of 345 MPa (50,000 psi)
All other miscellaneous secondary members and will conform to the physical specifications of
shall have a minimum yield strength of 250MPa ASTM A-653 or A-792 or equivalent.
(36,000 psi).
2.4.2.2 The zinc coating is a hot dip galvanization
2.3.4 Connections: process conforming to ASTM Specification A653
with a coating class of G-90 (0.90 oz/ft2 or 275
g/m2) or with galvalume coating to ASTM A-792 -
2.3.4.1 All field connections shall be bolted
AZ 150 (150 g/m2) or equivalent.
(unless otherwise noted).
2.4.2.3 The painting shall be baked enamel
a. All primary bolted connections, as shown on
polyester or High Durability ( HD ) polyester
drawings, shall be furnished with high strength
for color sheeting with a film thickness of 25
bolts conforming to the physical specifications
microns. The reverse side shall be white with 10
of ASTM A-325 (or equivalent). All high strength
microns film thickness.
bolts, nuts and washers shall be zinc plated with
a bronze iridite finish for easy identification.
2.4.3 Panel configuration:
b.All secondary bolted connections, as shown
on drawings, shall be furnished with machine 2.4.3.1 “Kirby Rib” panel shall have 32 mm deep
bolts conforming to the physical specifications of major ribs which taper in width from 11 mm to 40
ASTM A-307 (or equivalent). Machine bolts, nuts mm, and are spaced 333mm on center. Between
and washers will be zinc plated. major ribs are additional minor stiffening ribs
spaced at 111 mm on center. Each panel shall
2.3.4.2 All shop connections shall be welded provide one meter coverage.
using either submerged or shielded arc
process, and welding shall be in accordance 2.4.3.2 “Kirby Wall” panel shall have 26.4 mm

18
deep major ribs which taper in width from 29 the panel shall be spliced, and endlap shall be 100
mm to 59 mm and are spaced 333mm on center. mm wide (minimum) and occur over a wall girt.
Between the ribs the panel shall be formed into
a sculptured “Valley” shape. Each panel shall 2.4.6.3 Endwall panels shall be continuous from
provide one meter coverage. the eave to 40 mm below the column base plate,
except where the required panel length would
2.4.3.3 “Kirby Deck” panel shall have 41 mm exceed 9.0m. For a panel length in excess of
deep major ribs which taper in width from 12 9.0m, the panel shall be spliced and the endlap
mm to 42 mm, and are spaced 164 mm on center. shall be 100mm wide (minimum) and occur over a
Additional minor stiffening ribs are located wall girt. All endwall panels shall be square cut in
between major ribs, at 82 mm on center. Each the factory for 1:10 slope buildings, or bevel cut
panel shall provide 820 mm coverage. in the field for 3:10 slope buildings.

2.4.4 Fasteners: 2.4.6.4 All laps of roof panels shall be sealed

with a continuous ribbon of tape sealer.
2.4.4.1 Standard fasteners shall be No 14, Type 2.4.6.5 Roof panels shall be secured to
A, self-drilling sheet metal screws with metal intermediate framing members with No. 14 sheet
and EPDM washers, which conform to American metal screws at a maximum spacing of 333mm.
Standards Association Specifications. All screws At endlaps, the maximum spacing of screws shall
shall have hex heads. be 111 mm. At four corners of the buildings, panel
to structural fastener spacing shall not exceed 111
2.4.5 Sealer: mm, to an area equivalent to x2. Dimension x is
determined by the following rule:
2.4.5.1 Sealer for sidelaps, endlaps and self-
flashing windows shall be 6 mm wide x 5 A. The smaller of
mm thick, composed of synthetic rubbers,
plasticisers and inert fillers. The sealer shall be (1) 10 % of the least horizontal dimension of the
non-asphaltic, non-shrinking, non drying and non- building (span or length)
toxic and shall have superior adhesion to metals,
(2) 40 % of the eave height.
plastics and painted surfaces at temperatures
from -40°C to +90°C. B. But not less than

2.4.6 Installation of roof & wall panels: (1) 4% of the least horizontal dimension of the
building
2.4.6.1 Roof panels shall be continuous from
ridge to eave for buildings 18m wide or less, (2) 0.9 meter
where endlaps are required, the width shall
2.4.6.6 Wall panel shall be secured to
be approximately 150 mm (as specified on the
intermediate framing members with No. 14 sheet
drawings), and shall occur over a roof purlin.
metal screws at a maximum spacing of 333mm.
2.4.6.2 Sidewall panels shall be continuous from At endlaps, the maximum spacing of screws shall
the eave to 40 mm below the column base plate, be 166mm.
except where the required panel length would
2.4.6.7 Sidelaps of roof panels shall be stitched
exceed 9.0m. For a panel length in excess of 9.0m,
through the high rib with two, equally spaced,

19
 2.5 ACCESSORIES

No. 14 sheet metal screws between supports 2.5.1 Personnel doors:

(screw spacing not to exceed 525 mm). Sidelaps
of wall panels shall be stitched through the low
2.5.1.1 Single swing doors are designated as
rib with one No. 14 sheet metal screw centered
3070M and 3070G. Double Swing doors are
between two supports (screw spacing not to
designated as 6070M and 6070G
exceed 1050 mm).
2.5.1.2 Door leaves shall be 45 mm thick, full
2.4.7 Flashing, trim & closures: flush, fabricated from electro galvanized steel of
0.9 mm nominal thickness (20 gauge) including
2.4.7.1 Flashing and/or trim shall be furnished the base steel and zinc coating. Door shall have a
at the rake, corners, eaves, framed openings, solid core of rigid polyurethane (foamed in place)
and wherever necessary to provide weather to completely fill the inside of door. 3070G and
tightness and finished appearance. Color shall be 6070G doors shall be provided with opening
selected from Kirby Building Systems standard for glass for field glazing (glass and glazing by
colors, with the exception of the corner trim, others).
which matches the building wall color.
2.5.1.3 3070 doors shall be furnished with a
2.4.7.2 Color coated steel for flashing, metal cylindrical lock set which meets or exceed U.S.
closure, trim and other miscellaneous uses shall Federal specification F.F.H. 106a -Series 160A.
be 26 gauge of the same specification as the roof
and walls covering material. 2.5.1.4 6070 doors shall be furnished with a
cylindrical lock set on one leaf and a cylindrical
2.4.7.3 A formed peak panel matching the slope handle set on the other leaf.
and profile of adjoining panels shall be provided
along the building ridge. 2.5.1.5 Inactive leaf of the 6070 door (R.H.
inactive) shall have a fool, head and a chain
2.4.7.4 Solid or closed cell, preformed, E.T.P. bolt supplied loose for field installation, unless
(Ethylene Polypropylene Terpolymer) closures specified otherwise astragal shall be installed on
matching the profile of the panel shall be right hand inactive leaf.
installed along the eave, rake and other locations
specified on Kirby Building Systems drawings. 2.5.1.6 Each door leaf shall swing from three 114
x 114mm galvanized steel, interlocking template
2.4.8 Color finish: butt hinges.

2.5.1.7 Door frame consisting of jambs and

2.4.8.1 Unless specified otherwise, all wall and header is of knock down type for field assembly
roof panels, flashing, trim and other exposed through bolted connections, jambs and header
steel surfaces shall be color coated. are made from cold formed 1.5mm thick 36 KSI
steel 210mm deep.
a. Color of panels and corner trim shall be
selected by the customer from Kirby Building 2.5.1.8 Door leaves and frames shall be shop
Systems standard colors. painted with one coat of vinyl base neutral gray
primer.
b. The gutters, downspouts, rake trim, eave trim and
door flashing shall be white unless otherwise selected 2.5.1.9 The threshold shall be an extruded aluminum
from Kirby Building Systems standard colors. shaped to provide adequate weather seal

20
2.5.2 Sliding doors: locking devices and handles, single slide doors
shall have a retainer at one end.
2.5.2.1 Sliding door shall be constructed from 2.5.2.9 Door framed opening jambs shall be cold
cold formed channel or Zee shaped steel formed shapes. The cold formed members shall
framing, having a minimum yield strength of 345 be given one shop coat of standard primer.
MPa (50,000 PSI). The framing shall be covered
on the outer face with panels as specified for the
wall. The door leaves shall be adequately flashed
2.5.3 Roll-up doors:
and counter flashed. Doors are field assembled
with bolted connections. Roll-Up doors are supplied as buyouts generally
in accordance with the following specifications:
2.5.2.2 Door leaf covering the framed opening
of the door when split into two parts, each part 2.5.3.1 Door curtain shall be color coated 22
sliding in the opposite direction shall be referred gauge galvanized steel having a minimum yield
to as double slide door. strength of 345 MPa (50,000 psi) and will
conform to the physical specifications of ASTM
2.5.2.3 Door leaf covering the framed opening of A653 or equivalent. Class G-90 (0.90 ozjft2
the door with a single leaf sliding in one direction or 275gjm2) or its equivalent. Curtain shall be
shall be referred to as single slide door. constructed of interlocking roll formed slats,
to provide curtain stiffness to withstand wind
2.5.2.4 The door leaves shall be suspended from pressures of 1.25 KNj m2. Alternate slats are to
trolley which is guided on a header assembly. be equipped with endlocks to prevent lateral
The header is cold formed C section, track is movement of the slats. Endlocks are made of
welded to header channel, header assembly is Nylon secured to the slat by Nylon rivets. The
supported at four points by brackets which are bottom of each curtain shall be reinforced by
connected to the building wall framing. Header cold formed steel trims.
assembly is protected by a counter flashed hood.
2.5.3.2 Guides are to be fabricated from 3mm
2.5.2.5 Trolleys are galvanized sheet metal minimum thickness steel having minimum yield
stamping having four wheels on two axel, the strength of 345 MPa (50,000 psi), assembled
axel is supported on nylon (teedelrin) bearings with 10 mm DIA. bolts to the door jambs.
housed in the trolley body. A pivoted bolt with
two nuts is provided at the center of the body 2.5.3.3 Door curtain is secured to spiders which
for suspending the door leaf. is welded to 40 N.B.M.S. pipe, each end of the
pipe is fitted with precision machined shafts to
2.5.2.6 Adequate weather sealing is provided at accept the bearing. Antifriction ball bearings are
center and at ends by neoprene rubber closures provided which are housed in a pillow block or
and strips. flange mounting.

2.5.2.7 Wind reaction and swaying at the bottom 2.5.3.4 Brackets are constructed from steel
is absorbed by V shaped cold formed guide plates of 6mm thick minimum or structural
made of 3.5mm thick 50 KSI steel embedded angles. Holes are prepunched on the bracket
in the concrete foundation through angle guide to install it on the supporting column or door
provided for this purpose. jambs, and to receive the bearing block and the
operator.
2.5.2.8 The doors shall have inside and outside

21
2.5.3.5 Operation: 2.5.4 Windows:
a) Manual Operator: 2.5.4.1 Aluminum windows are specifically
designed for installation with exterior wall panel.
Manually operated by means of endless Windows shall be singleslide
galvanized hand chain. Locking clip shall be
provided for securing the chain. Hand chain (horizontal) self flashing with preglazed clear
wheel is attached to worm reduction gear box, glass and removable half insect screen, complete
the output shaft of the reducer is connected to with latching device, weather stripping.
the door shaft by means of a rigid coupling.
2.5.4.2 Single windows are IM wide x IM high
b) Electric Operator: nominal size, double or multiple windows are
formed by joining the window jamb fins together.
Electric operation is by means of an integral
motor reducer, connected to the door shaft by 2.5.4.3 Windows shall be fitted with 2.4 mm (
a set of sprockets and roller drive chain. The 3/32” )D.S.B clear glass using vinyl glazing beads
unit is mounted on the support brackets. Motor and shall be back bedded
operates on 380- 415 volts, 3 phase 50/60 Hz.
rated for the specific application-with high 2.5.4.4 All structural members shall be
starting torque. Insulation class F or E, type of extruded aluminum with a minimum thickness
motor is T.E.F.C. of 1mm, assembled with screws and sealed
at junctions, and shall meet or exceed the
Primary reduction is by worm and worm wheel American Aluminum Manufacturers Association
with an extended shaft to accept a chain wheel Specification HS-B2.
for emergency manual operation by hand chain.
2.5.4.5 Nylon roller and roller housing is attached
Limit switches shall be provided for upper to each end of sash bottom rail.
and lower limit, mounted on reducer housing,
actuated by rotary gear with adjustable strikers. 2.5.5 Sky light:
Control buttons are set in a rigid box for up and
down door operation, with emergency stop and 2.5.5.1 Sky Light are made of translucent
built in overload cut out. fiberglass reinforced polyester to the profile
of Kirby rib panel called skylight and Kirbywall
Electro-magnetic spring set disc brake is fitted panel called wall light and are available only in
to the motor end, totally enclosed to protect 2.44 Kg/m2 (8 ounces/ft2). Conforming to U.S.
against damage from dust and moisture, manual Commercial Standard CS-214-517.
release attachment (auto reset) for emergency
operation in case of power failure is provided for 2.5.5.2 Each panel has a coverage of 1 meter.
hand chain operation. Standard length for skylight is 3305 mm and for
wall light is 4140mm. Panel shall be of 1.5mm thick.
Brakes are provided for door above 16M2 area
only, the braking is effected on smaller doors by 2.5.5.3 Color of the panel shall be white with
means of self-locking gear box. smooth surface finish with a light transmitting
capacity of 60 % ± 5%

2.5.5.4 Installation of light panels is similar to that

22
of steel panel, it can be worked with ordinary furnished to ensure weather tightness.
tools and may be drilled, sawed, punched
without damage to panel and are shatter 2.5.7.3 Individual ventilators are furnished with
resistant. one set of Standard accessory package for
damper control. Multiple units are furnished with
2.5.5.5 Light panels have low heat transmission one set of accessory package for two ventilators
acts as insulation. (K factor 1.0 to 1.5; U factor and shall be manually operated pull type.
1.09) and are not affected over a temperature
range of 50°F below zero to 200°F. (fire 2.5.7.4 Outer shell, damper, rain shield, end
resistance 25 flame spread, test according to UL- cap and skirts shall be fabricated from 26 GA
94 tunnel test). galvanized steel painted white base metal
conforming to ASTM specifications A653 Grade
Panels are corrosion resistant and most 50, G90 or its equivalent.
chemicals do not affect the panels.
2.5.7.5 Skeleton of the ventilator is made of
2.5.6 Eave gutters and down spouts: galvanized sheet metal stamping and cold-
formed members of 1mm thick minimum,
assembled with rivets.
2.5.6.1 Eave gutters shall be box shaped, color
coated, 0.5 mm nominal thickness (26gauge) 2.5.7.6 Ventilators shall be furnished with bird
galvanized steel. The outside face of the gutters screen.
shall be supported with color coated, 0.5 mm
nominal thickness (26 gauge) galvanized straps to
2.5.8 Louvers:
the eave member at a maximum spacing of 1.20 m.

2.5.6.2 Downspouts shall be rectangular shaped, 2.5.8.1 Std Louvers are adjustable with
color coated, 0.5mm nominal thickness (26 overlapping type blades providing maximum
gauge) galvanized steel. Downspouts shall have weather tightness while closed, allowing free air
a 45-degree elbow at the bottom and shall be flow while open. Standard nominal size of louver
supported by attachment to the wall covering at is 1M wide by 1M height, self supporting on K.W.
3.0 m maximum spacing. profile wall panel and self flashing,

2.5.7 Ventilators: 2.5.8.2 Sandtrap Louver

2.5.8.2 Multiple units are formed by joining the

There are 2 types of ventilators supportfins; suitable jamb supports shall be
furnished for multiple unit installation.
1. 300mm throat ( Standard with adjustable damper)
2.5.8.3 Std Louver frames are fabricated from
2. 600mm throat ( KRV-600 with fix type) 1.2mm thick (18 gauge) galvanized steel, and
blades from 0.9mm thick (20 gauge) galvanized
Ventilators shall be supplied in length of 3m
steel, conforming to ASTM specification
shopassembled. Ventilators shall be supplied in
A653 Grade 50 steel,G-90 galvanizing or its
length of 3m shop assembled.
equivalent. Louver shall be painted white.
2.5.7.2 Ventilators are designed specifically to
2.5.8.4 Std Louvers are furnished with crank
fit on top of Kirby rib roof panel, end cap skirt
and levers for the adjustment of blades and the
assembly, closure strips and sealants shall be

23
outside face of louver is fitted with removable manufactured from a self- extinguishing glass
insect screen. fiber reinforced polyester 3 mm thick with 15 mil
polyester gel coated weathering surface on
2.5.9 Insulation:

2.5.9.1 The insulation shall be fiber-glass, blanket exterior. Unit shall be white in color and opaque
type and suitable for application to roofs and to light. Base shall have the same configuration
walls of industrial buildings. The insulation shall as the Kirby rib profile. The top of the curb shall
be made of long and fine fiber-glass evenly provide a level surface at 1.10 roof slope.
distributed and of uniform density bonded with
phenolic thermosetting resins with a vinyl facing 2.5.10.2 Curbs shall be available in sizes of 600 x
resulting in strength, long life and low water 600 mm, 900 x 900 mm and 1200 x 1200 mm.
permeability.
2.5.11 Roof jack:
2.5.9.2 The standard insulation thickness shall be
50mm and 75mm supplied in rolls. The density
of the insulation shall be 10 kg/m3 with a thermal 2.5.11.1 Roof jacks shall be a one-piece
conductivity of 0.31 BTU in/ft2 hr °F at a mean construction manufactured from self-
temperature of 77 °F. extinguishing fiber glass reinforces polyester
3mm thick with 15 mil polyester gel coated
2.5.9.3 The fire resistance of the facing shall be in weathering surface on exterior. Unit shall be
accordance with the Underwriters’ Laboratories white in color and opaque to light. Base shall
Test Method UL723, and shall have a fire hazard have the same configuration as Kirby rib profile.
classification for flame spread 15 and smoke
developed 105 2.5.11.2 Roof jacks shall be available in opening
sizes of 50-100 mm and 150-300 mm in jack
2.5.9.4 The vinyl facing shall have a high vapor heights of 365 mm and 290 mm respectively.
barrier efficiency with a low perm rating to
prevent condensation. 2.6 SANDWICH PANEL
2.5.9.5 The insulation material shall neither POLYURETHANE
promote nor accelerate corrosion on steel. The
insulation shall be tough, resilient, dimensionally
INSULATED PANELS
stable and have a high ageing resistance. It shall
be odorless, non hygroscopic, chemically inert 2.6.1 General:
and resistant to humidity, corrosive vapors,
moisture and insects. Sandwich Panels shall be manufactured by
the press injection method to produce a rigid
2.5.9.6 The insulation shall be easy to install polyurethane core between exterior steel
and can be cut with an ordinary knife to allow facings. The manufacturing process shall be
installation even on special profiles, curves, carefully controlled with steel facings maintained
T-pieces etc. at around 40 C during the injection process to
ensure proper reaction and adhesion. Also the
2.5.10 Roof curb: pressure on the moulds shall not be released till
completion of reaction.
2.5.10.1 Curbs shall be one-piece construction

24
2.6.2 Panel types: 2.6.4 Panel thickness:

The Sandwich Panels are available in three types, Type KRIP Panels shall have a nominal thickness
i.e. KRIP, KWIP, and KCIP. Panel type KRIP is of 40mm, 50 mm, 60mm, 75 mm or 100 mm at
suitable for application as an exterior roof or wall bottom of ribs.
panel, Type KWIP is suitable for wall panel, and
KCIP for wall and partition panels. All three types Type KWIP panels shall have a nominal thickness of
of panels shall be supplied in 1 Meter net coverage. 40mm, 50 mm, 65 mm or 75 mm at bottom of ribs.

2.6.3 Panel facing: Type KCIP panels shall have a nominal thickness
of 50 mm, 60 mm, 75 mm or 100 mm.

Standard panels shall have both exterior and

2.6.5 Panel core:
interior facings of 26 Gauge steel galvanized and
color coated having a minimum yield strength
of 345 MPa (50,000 psi) and shall conform to Standard panels shall have core insulation of
the physical specifications of ASTM A-653 or rigid polyurethane foam which shall be foamed-
equivalent. The zinc coating shall be by hot dip in-place between panel facings and shall have
galvanization process G90 ( 0.90 oz/ft or 275 g/ an approximate total density of 40Kg/m3, with a
m2) and for galvalume coated panels to A-792 AZ heat transmission value of 0.0198 Watt/M2.
150 or its equivalent. The painting shall be baked
The mechanical properties of the foam shall have
enamel polyester (white) or silicon polyester
approximately the following values:
(color blue or gold) with a film thickness of 25
microns. The reverse side shall be white with 10
Compression Strength
microns film thickness.
(at 10% deformation) = 1.6 Kg/cm2
Compression Modulus = 36 Kg/cm2
The panel facing profiles shall be as follows:
Shear (with metal sheet) = 1.63 Kg/cm2
a) Type KRIP & KWIP Shear Modulus = 20.4 Kg/cm2
Adhesion to metal sheet = 1.5 Kg/cm2
Standard panels shall have exterior skin Water Vapor Transmission = 80 gr/24hm2
26 Gauge steel galvalume / galvanized and Water Absorption = 4 % in volume
prepainted Kirby rib or Kirby wall profile Closed Cell Content = 95 % min
sheets. The interior skin shall be 26 Gauge steel
galvanized and color coated, generally flat profile
2.6.6 Fasteners:
sheet with low ribs at 250 mm centers.
Standard fasteners shall be No. 14 self drilling
screws with EPDM washers. All screws shall have
b) Type KCIP
hex heads.
Standard panels shall have both exterior and 2.6.7 Sealer:
interior skins of 26 Gauge steel galvanized
or galvalume substrate and color coated of
generally flat profile. KCIP panels are provided Panel type KRIP shall have sealer for sidelaps
with tongue & groove joints with concealed and endlaps of 6mm wide x 5thick pressure
fasteners. sensitive butyl tape. The sealer shall be non-
asphaltic, non shrinking, non drying and non
toxic and shall have superior adhesion to metals,

25
plastics and painted surfaces at temperatures building
from 50°C to + 104°C. KCIP panels are supplied
(2) 0.9 meter
with tube sealant for field application and joints.
2.6.8.6 Wall panels shall be secured to
2.6.8 Installation of roof & wall panels intermediate framing members with No. 14 self-
(type KRIP/KWIP): drilling and tapping screws at a maximum spacing
of 333 mm. At endlaps the maximum spacing of
2.6.8.1 Roof panels shall be continuous from screws shall be 111 mm.
ridge to eave for buildings 18m wide or less,
where endlaps are required, the width shall 2.6.8.7 Sidelaps of roof and wall panels shall be
be approximately 150 mm (as specified on the stitched through the high rib with No. 12 sheet
drawings), and shall occur over a roof purlin. metal screws at 500 mm centers.

2.6.8.2 Sidewall panels shall be continuous from 2.6.9 Flashing, trim & closures:
the eave to 40 mm below me column base plate,
except where the required panel length would
2.6.9.1 Flashing and/or trim shall be furnished
exceed 9.0 m. For a panel length in excess of 9.0 m,
at the rake, corners, eaves, framed openings,
the panel shall be spliced, and endlap shall be 100
and wherever necessary to provide weather
mm wide (minimum) and occur over a wall girt.
tightness and finished appearance. Color shall be
2.6.8.3 Endwall panels shall be continuous from selected from Kirby Building Systems standard
the eave to 40 mm below the column base plate, colors, with the exception of the corner trim,
except where the required panel length would which matches the building wall color.
exceed 9.0 m. For a panel length in excess of 9.0
m, the panel shall be spliced and the endlap shall 2.6.9.2 Color-coated, galvanized steel for
be 100 mm wide (minimum) and occur over a wall flashing, metal closure, trim and other
girt. All endwall panels shall be square cut in the miscellaneous uses shall be 26 gauge of the
field for 3:10 slope buildings. same specification as the roof and walls covering
material.
2.6.8.4 All laps at roof panels shall be sealed with
a continuous ribbon of tape sealer, 2.6.9.3 A formed peak panel matching the slope
and profile of adjoining panels shall be provided
2.6.8.5 Roof panels shall be secured to along the building ridge.
intermediate framing members with No. 14 sheet
metal screws at a maximum spacing of 333 mm. 2.6.10 Color finish:
At endlaps, the maximum spacing of screws shall
be 111mm. At four corners of the buildings, panel
2.6.10.1 Unless specified otherwise, all wall and
to structural fastener spacing shall not exceed 111
roof panels, flashing, trim and other exposed
mm, to an area equivalent to x2 Dimension x is
galvanized steel surfaces shall be color coated.
determined by the following rule:
A. The smaller of a. Color of panels and corner trim shall be
selected by the customer from Kirby Building
(1) 10% of the least horizontal dimension of the
Systems standard colors.
building (span or length)
(2) 40% of the eave height. b.The gutters, downspouts, rake trim, eave trim
and door flashing shall be white unless otherwise
B. But not less than
selected from Kirby Building Systems-Kuwait
(1) 4% of the least horizontal dimension of the standard

26
3 : STANDARD STRUCTURAL SYSTEMS

3.1 STANDARD FRAMES

MAIN FRAMES
Standard frame types:
Suggested width range (metres) for most economical buildings.

Standard Eave height : 3 m - 8 m The table above is a general guideline on

Standard bay spacing : 6m / 7.5m / 9m recommended frame types for different widths.
Standard Loadings : Live load 0.5/0.6/1.0 kN/M2 Kirby custom designs each order to the specified
type, width, height, bay spacing, loading
Wind load 0.75/1.0/1.25 kN/M2 and other building parameters to customer
requirements.

27
3.2 STANDARD LOADINGS

Single Gable buildings:

Standard buildings are available for the following Design wind co-efficients for enclosed
loadings: single gable buildings
Dead load = building self weight Asce 7 -10
Live load = 0.57 Kn /m2 ( GCPe - GCPI )
Wind load = 1.25 Kn /m2

C1 C2 C3 C4
h<60 ft.
Balanced +0.22 -0.87 -0.55 -0.47 w/h<1
Un-Balanced +0.58 -0.51 -0.18 -0.11

P = (wind pressure)
P = q (c ), where c is wind co-efficient

28
Single slope buildings:

T-canopy:

L-Canopy:

ƒƒ S
tandard loadings are same as for single gable applied as per table for single gable buildings.
buildings. ƒƒ F
ull wind load (c=1.3 ) Is applied for t-canopy &
ƒƒ Wind coefficients for single slope buildings are l-canopy structures.

29
3.3 STANDARD BUILDINGS

Width Length Eave height Bay Project no. Page

(M) (M) (M) spacing
36.00 48.00 6.00 [email protected]. BC-36660 212
36.00 48.00 8.50 [email protected]. BC-36685 218
36.00 48.00 6.00 [email protected]. BC-36860 224
36.00 48.00 8.50 [email protected]. BC-36885 230
18.00 48.00 6.00 [email protected]. RF-18660 236
18.00 48.00 8.50 [email protected]. RF-18685 242
18.00 48.00 8.50 [email protected]. RF-18885 248
21.00 48.00 6.00 [email protected]. RF-21660 254
21.00 48.00 8.50 [email protected]. RF-21685 260
21.00 48.00 6.00 [email protected]. RF-21860 266
21.00 48.00 8.50 [email protected]. RF-21885 272
36.00 48.00 6.00 [email protected]. RF-36660 278
36.00 48.00 6.00 [email protected]. RF-36685 284
36.00 48.00 6.00 [email protected]. RF-36860 290
36.00 48.00 8.50 [email protected]. RF-36885 296

Building installation drawings are located at chapter 7,

7.26 Page 211- standard buildings continuation

30
3.4 STANDARD CABLE
BRACING SYSTEM

Wind forces acting transversely are transferred foundation. The reactions at the top of each wind
to the foundation by means of “Frame Action”. column is transmitted to the Roof system where
However, wind forces acting longitudinally (i.e. each braced bay takes it proportional share of
On the end wall) are transferred by means of wind reaction. Full Wind is applied in accordance
roof and walls bracing between frames. Number with asce 7 -10.
of braced bays depends on width and length of Standard roof and wall bracing consists of
building. galvanised extra high strength seven
Strand cable of 12.7Mm diameter ( 1/2”) acting
All braced bays share equally in transmission always in tension.
of wind reactions from the wind column to the

31
3.5 PORTAL FRAME
BRACING SYSTEM

When sidewalls are open for access (passage) mounted on main frame columns just to clear the
or where there are accessories such as doors haunch connection of m.F. Column and rafter.
etc., Portal bracing (wind bents) is substituted The structural design of portal frames is based
in walls of braced bays instead of cable bracing. on rigid connection between portal
Horizontal and vertical clearance must be Columns and beam, and a pinned base condition.
considered since the portal bracing members are

3.6 KNEE BRACING SYSTEM

When diagonal bracing is not allowed in sidewalls continuous as required by design with diagonal
because of access or accessories such as doors angle braces connecting the beam to the main
etc. And portal frame cannot be used for bracing frame column web.
because of clearance, a knee brace is used as The structural design of knee brace is based on
shown in sketch above. the beam being pinned at both ends
A knee brace consists of a hot rolled beam in With the main column designed for weak axis
the purling line either only at braced bays or bending.

32
3.7 DIAPHRAGM BRACING
SYSTEM
Diaphragm bracing system
Diaphragm action:

Kirby wall panels properly fastened to sheeting acting as a diaphragm is approximately

supporting structural framing form structural 2.2 Kn/m (150 lbs/ft).
units capable of resisting loads through in-plane The minimum effective lenghts of sheeting
shear resistance. This shear resistance required at sidewalls of standard space saver
Effects a shear transfer of these loads to Buildings and at endwalls of all standard
the foundation with a minimum amount of buildings with bearing endwalls for the
Deflection. Such resistance is referred to as Standard windload of 1.25 Kn/m2 are shown
‘diaphragm action’. in the following tables. The effective lengths
The wind loads acting on the endwalls of shall be exclusive of any framed openings for
standard space saver and lean-to buildings and accessories etc.
on a portion of the sidewall at standard bearing Diaphragm action table:
endwalls are transferred to the
Foundation by diaphragm action of the flush girts
Effective length of sidewall sheeting (meters)
and sheeted walls. The resistance of kirby-wall
required for diaphragm action:
Effective length of endwall sheeting (meters)
required for diaphragm action:

Span Eave height (meters)

(meters) 3 4 5 6 7 8
6 2.0 2.7 3.3 3.9 4.6 5.2
9 3.0 4.0 5.0 5.9 6.9 7.9
12 4.1 5.4 6.7 7.9 9.2 10.5
15 5.2 6.8 8.4 10.0 11.6 13.2
18 6.3 8.2 10.1 12.0 14.0 15.9

Effective length of endwall sheeting (meters)

required for diaphragm action:

Eave Ht. (Meters) 6.0 M End bay 7.5 M Endbay

3 2.0 2.4
4 2.6 3.2
5 3.3 4.1
6 3.9 4.9
7 4.5 5.7
8 5.2 6.5

33
3.8 STANDARD EAVE
CANOPY can be added to any of the standard frame type
buildings.
A standard eave canopy up to 1.5M wide and a
For canopies other than standard, refer to sales
standard endwall purlin extension of up to 1.73M
office or headquarters for a special price and
details.

3.9 STANDARD FASCIA

The standard fascia extends out 667 mm from
A standard fascia of upto 1.8 Meters height can the sidewall and endwall steel line, is single
be added to any of the standard frame type sheeted and provided with soffit.
buildings. For fascias other than standard refer to sales
office or headquarters for a special price and
details.

34
3.10 STANDARD
EXPANSION JOINTS
Expansion joint at roof:

Expansion joint at wall:

A longitudinal expansion joint is provided for If the width of the building exceeds 120 meters,
buildings with length greater than 120 meters as double columns are used to cater for Expansion.
shown above.

35
3.11 STANDARD ENDWALL
SYSTEMS

Standard endwall systems: Main end frames:

Endwalls of standard buildings have two light A main end frame is normally used when a future
endwalls. The light endwall rafter is a hot-rolled extension to the building is required. It is also used
I-section and is designed as a continuous beam over for buildings with cranes or full open endwalls. A main
wind column supports. The Standard corner columns end frame is designed for a full bay loading similar
are i-sections designed as pinned at both ends. to an interior frame. Main end frame centerline is
The endwall girts are fwsh with the wind columns. located 356 mm from the endwall steel line.
As there is no frame action at a light end frame, the
lateral wind-load from the half-bay tributary area A building with only two bays shall have at least one
acting on the frame is resisted by the diaphragm main end frame while building with only one bay shall
action of the sheeted endwall. have both main end frames.

36
3.12 STANDARD WIND
COLUMN SPACING

All dimensions are in meters

37
3.13 STANDARD WIND
COLUMN SPACING WITH
MEZZANINE

All dimensions are in meters

38
3.14 STANDARD ANCHOR
BOLTS DETAIL

39
4 : SPECIAL STRUCTURAL &
PRE-ENGINEERED BUILDING SYSTEMS
4.1 RIGID FRAMES WITH
OVERHEAD CRANES

Rigid frames with overhead cranes:

considered in the design of the main frames and
Rigid frame buildings with electric overhead the crane system. Cranes travelling outside the
travelling cranes are designed for the effect of building are supported on independent ‘a’ or ‘h’
the loads in accordance with the aisc manual. frames as required.
Cranes of 3.2 Mt., 5.0 Mt. ,10.0 Mt. and 15.0
Mt. up to a span of 21 meters are mounted on
brackets welded to the main frame columns. For
Cranes:
crane capacities in excess of 1o ml. It is generally
recommended to provide independent support Buildings can be designed to support any
columns tied laterally to the main frame columns. required crane system. Generally, overhead
The complete crane system includes brackets/ travelling cranes up to 15 mt are supported on
columns, bracing beam and crane runway. brackets. for higher capacities, an independent
support system is provided. Crane support
In the design of the rigid frame an impact for overhead travelling cranes includes brackets,
allowance of 10 % of max. Wheel load is beams and bracings.
considered for pendant operated and 25 % of
max. Wheel load for cab operated cranes. The
lateral force due to the effect of moving crane
trolley is 20 % of the sum of the lifted load and
crane trolley (exclusive of other parts of the
crane). The longitudinal force is 10 % of the
max. Wheel load. The lateral and longitudinal
forces are applied at the top of rail. The loading
conditions in accordance with MBMA are:

Dead + wind load,

Dead + crane loads + one-half live or wind load
Dead + crane loads + 3/4 snow load
Whichever is critical.

In buildings with multiple Cranes effect of the

moving loads for the worst case of loading is Al-adasani pipe factory - kuwait

40
4.2 MULTI-SPAN FRAMES &
TRUSSES

Multi-span frames:
and building heights are possible by running
Multi-span frames up to 6 spans or 120 meters service pipes/ducts through the trusses.
are analysed without lateral expansion joint. For Foundation costs are also reduced due to fewer
frame widths in excess of the above, a double columns being required to support larger spans.
column expansion joint is provided. Exterior The kirby truss system structures are individually
columns are built-up sections tapered or straight, designed to meet the specific requirements of
pinned or fixed at base depending on eave each building and are fabricated utilizing high
height of building. Exterior columns have rigid quality efficient fixtures. The system allows for
(moment) connection at top and the rafters are easy building installation as all connections are
built-up sections and continuous throughout the field bolted. Except for field splices on very large
length. Interior columns are generally pinned at spans, no site welding is required.
both ends. Valley gutters are designed assuming
interior downspouts (supplied by others) at
bay spacing. However if internal drainage is not
allowed larger valley gutters can be supplied
depending on the drained area of the roof.

Trusses:

Kirby truss system is one of the company’s most

popular and highly economical products. It is a
rigid structure, ideal for large span roof systems,
multiple bay buildings and as mezzanine floor
framing. Significant reductions in clearances Sultan centre - kuwait

41
4.3 MULTI-STOREY
BUILDINGS

Multi storey bank building

Multi-storey structures are available in

the following types:

Type No. of spans No. of floors

Al 1 2
A2 1 3
A3 1 4
Bl 2 2
B2 2 3
Cl 3 2
Dl 4 2

Columns and joists are fabricated from hot deck is profiled galvanised sections suitable
rolled sections and beams from either hot for supporting the dead load of the reinforced
rolled or built-up sections. Floor and roof steel concrete slab and 0.5 Kn/m2 construction load.

The standard design loads are:

Floor - live load = 4 kn/m2 suitable for residential and office occupancy.
Dead load = 4 kn/m2 which covers self wt. of steel framing, concrete slab
(100 mm), light floor finishes (carpets, vinyl tiles) light weight
partitions, ceilings and services.
Roof - live load = 1 kn/m2
- Dead load = 5 kn/m2 which covers all loads as for floor plus built-up roof.
-Wind load = 1.25 Kn/m2
All beam to column connections are moment resisting connections field bolted with H.S. Bolts.

42
4.4 MEZZANINE FLOORING
SYSTEM

The standard mezzanine framing consists Beams and joists are designed as simply
of profiled steel deck, joists, beams and supported at both ends and the intermediate
intermediate support columns. Beams are support columns are designed as pinned at both
built-up sections spanning in the longitudinal ends. The standard design live load is 5 kn/m21
direction, joists are hot rolled sections spanning covering most of the occupancies encountered
in the lateral direction and intermediate support in usual practice per aisc tables and the Design
columns are either pipe sections or hot rolled Dead Load is 3 kn/m2 which covers self weight of
aisc shapes. framing, 100 mm concrete slab and light finishes.
Refer to tables for the standard intermediate
The standard mezzanine finished floor level is column spacings and the occupancies covered
3.5 Meters with a clear height at bottom of joists for the standard live load.
of 3.1 Meters. The total thickness of floor slab
inclusive of deck and finishings is assumed to be Mezzanine floors of non-standard dimensions
100 mm. and loading to suit special customer
requirements are also available upon request.

43
4.5 OPEN WEB STEEL
JOISTS
Definition:
increasing the weight.
The Open Web Steel Joist is a secondary steel
ƒƒ Ducts and mechanical accessories can be
truss member fabricated from crimped angles
installed in between the web openings .
welded onto top and bottom chords. The
ƒƒ Cambering will prevent tiles, partitions or
elements of the open joist are made of hot rolled
any other delicate finishings from cracks by
as well as cold formed grade 50 steel. Open
maintaining the finish floor level straight.
Web Steel Joists are used as mezzanine joists,
roof purlins, among others.

Advantages:

ƒƒ Offers an economical solution for long spans Aircraft Hangar with 14 m open web cantilever
carrying heavy loads or light loads compared joist erected at Kuwait International Airport.
to conventional steel structure .
ƒƒ Allows more clearance to the building by Kirby offered the customer a high quality
minimizing the mezzanine overall depth by economical solution using open web steel joists
designing beams at the short direction and in this project instead of a rival space frame
the joists at the long direction without option.

44
Detailing:

Open Web Steel Joist Connection Detail Section A -A

OPEN WEB STEEL JOIST

Specifications: Load tables:

Kirby Open Web Steel Joist is designed in Kirby’s Open Web Steel Joists is recognized
accordance with the latest editions of: Steel Joists by Kirby’s standard designation as follows: KJ
Institute (SJI), American Iron and Steel Institute (Depth mm)-(Chord Size-Letter) Example: KJ
(AISI), American Institute of Steel Construction 400-A.
(AISC), American Welding Society (AWS).

Material specifications are in accordance with

ASTM A570, A572, A10ll or equivalent.
Allowable total load (kN/lm) Open Web Steel
Joists
Span KJ 300-A KJ 300-B KJ 300-C KJ 300-D KJ 300-E KJ 300-F KJ 300-G KJ 300-H
(mm) 7.20 kg/m 8.93 kg/m 10.74 kg/m 13.53 kg/m 16.03 kg/m 19.4 kg/m 22.6 kg/m 26.33 kg/m
6000 3.20 4.80 6.00 8.50 10.10 13.00 15.30 18.40
7000 2.35 3.53 4.41 6.24 7.42 9.55 11.24 13.52
8000 1.80 2.70 3.38 4.78 5.68 7.31 8.61 10.35
9000 1.30 2.05 2.55 3.60 4.30 5.50 6.50 7.80
10000 1.05 1.66 2.07 2.92 3.48 4.46 5.27 6.32
11000 1.37 1.71 2.41 2.88 3.68 4.35 5.22
12000 1.10 1.30 1.90 2.30 3.00 3.50 4.20

45
 Span KJ 400-A KJ 400-8 KJ 400-C KJ 400-D KJ 400-E KJ 400-F KJ 400-G KJ 400-H
(mm) 7.4 kg/m 9.21 kg/m 11.09 kg/m 13.96 kgm 16.37 kg/m 19.88 kg/m 23.4 kg/m 27.26 kg/m
6000 4.30 6.60 8.20 11.60 13.90 17.70 21.00 25.20
7000 3.16 4.85 6.02 8.52 10.21 13.00 15.43 18.51
8000 2.42 3.71 4.61 6.53 7.82 9.96 11.81 14.18
9000 1.80 2.80 3.50 4.90 5.90 7.60 9.00 10.70
10000 1.55 2.38 2.95 4.18 5.00 6.37 7.56 9.07
11000 1.28 1.96 2.44 3.45 4.14 5.27 6.25 7.50

Span KJ 600-A KJ 600-8 KJ 600-C KJ 600-0 KJ 600-E KJ 600-F KJ 600-G KJ 600-H

(mm) 8.22 kg/m 10.19 kg/m 12.29 kg/m 15.45 kg/m 18.32 kg/m 21.98 kg/m 25.5 kg/m 29.42 kg/m
6000 6.60 10.10 12.60 17.80 21.40 27.40 32.40 38.90
7000 4.85 7.42 9.26 13.08 15.72 20.13 23.80 28.58
8000 3.71 5.68 7.09 10.01 12.04 15.41 18.23 21.88
9000 2.80 4.30 5.40 7.60 9.20 11 .70 13.90 16.70
10000 2.27 3.48 4.37 6.16 7.45 9.48 11 .26 13.53
11000 1.87 2.88 3.61 5.09 6.16 7.83 9.30 11 .18
12000 1.50 2.50 2.95 4.20 5.00 6.50 7.70 9.20
13000 2.00 2.50 3.50 4.30 5.50 6.50 7.80
14000 1.72 2.16 3.02 3.71 4.74 5.60 6.73

Span KJ 800-C KJ 800-D KJ 800-E KJ 800-F KJ 800-G KJ 800-H KJ 800-1 KJ 800-J

(mm) 13.45 kg/m 16.54 kg/m 19.43 kg/m 23.34 kg/m 27.42 kg/m 31.63 kg/m 34.24 kg/m 35.61 kg/m
11000 4.79 6.86 8.26 10.58 12.56 15.04 16.28 17.52
12000 3.99 5.63 6.81 8.68 10.33 12.44 13.50 14.55
13000 3.40 4.80 5.80 7.40 8.80 10.60 11.50 12.40
14000 2.93 4.14 5.00 6.38 7.59 9.14 9.92 10.69
15000 2.50 3.53 4.21 5.46 6.49 7.85 8.42 9.10
16000 2.20 3.10 3.70 4.80 5.70 6.90 7.40 8.00
17000 2.75 3.28 4.25 5.05 6.11 6.56 7.09
18000 2.34 2.90 3.68 4.46 5.35 5.79 6.24
19000 2.10 2.60 3.30 4.00 4.80 5.20 5.60
20000 2.35 2.98 3.61 4.33 4.69 5.05

For direct order, use the above tables 2. Move to the right until you Find your desired
load or nearest higher value.
as follows:
3. Read the column header KJ (Depth mm)-
(Size-Letter) and make your direct order from
Kirby’s Sales Offices.
1. Select your span from the First left column
[SPAN (mm)]

46
4.6 HANGAR DOOR
SYSTEM

Aircraft hangar - Jordan

Buildings with hangar doors are designed to The hangar door system is available as either
accommodate air crafts types DC8, DC9, B707, manually or electrically operated. For manually
B727 & B737. The maximum available door operated doors the top guide beams are hot
opening size is 51 meters clear width and 15 rolled angles or tee sections and for electrically
meters clear height. operated doors the top guide beams are hot
rolled i-sections which prevent the door leaves
For smaller doors up to a height of approx. 9 from slipping due to uplift of the frame from
meters an overhang header support system is wind forces. Hangar doors are supported on
provided and for larger doors above 9 meters rails embedded in concrete. The door leaf is
height an additional frame is used at the exterior adequately braced to resist the wind forces
to minimise deflection. and are offered with either one side sheeted or
both sides sheeted. Door pockets at ends are
supplied with either sheeted or open walls.

47
4.7 SPECIAL CANOPIES

Special canopies of width in excess of the standard as required. Canopies are supplied with or without
canopy width of 1.5 Meters and up to 6 meters are soffit. Canopies exceeding 6 meters are treated as
made of either hot rolled i-sections or built -up part of the frame through continuation of the roof
sections bolted to rafter end plate or column flange rafter.

48
4.8 SPECIAL FASCIAS

Special fascias:

Fascias are used for architectural purposes to Fascias are cantilevered from the main frame columns
conceal the gable of the building. A variety of fascias on the sidewall and from the wind columns on
either straight or inclined can be provided as shown the endwall. Flush fascias or parapets can also be
in the sketches. provided.

Fascias and canopies:

KIRBY provides fascias especially designed

to customer requirements. This can be either
vertical, horizontal or with curved sheeting to
enhance the architectural look of your building.
Wall canopies at eaves, endwalls, over doors and
windows are also available.
Kisr office building - Kuwait

49
4.9 BUILT-UP ROOFS

Built up roofs: 4.9A CONVENTIONAL

Built-up roofing is required for flat roofs and may be
BUILT-UP ROOFING SYSTEM
used for roofs with low slopes. It can be applied (not
by KBSK) over Kirby roof deck to weatherproof the Conventional built-up roof system may be
building to meet client specifications or architectural composed of some or all of the following elements
requirements. Buildings requiring built-up roofs shall depending on end use of the building, geographical
be identified at the design stage to ensure structural location, desired aesthetic effect, cost and other
adequacy for the required additional dead loads and factors. Roofing elements from inside to outside
compatibility to receive the specified built-up roofing of building over roof purlins/joists are Kirby steel
system. The two commonly used built-up roofing deck, vapor barrier, rigid insulation, reinforced
systems are briefly described below: concrete slab, alternate layers of saturated felt
and moppings of bitumen and an optional top
pouring of pitch or asphalt in which slag or gravel
may be embedded which completes the built-up
roof. Vapor barrier protects the insulation from
condensation wherever conditions of high humidity
exist inside the building or on roof decks in cold
climates and on decks of heated buildings where
winter temperature may fall below 7° C. Vapor
barrier materials commonly used are coated base
sheets, saturated felts, laminated kraft papers and
PVC sheets. Concrete slab supporting flat built-
up roofing is normally pitched towards drains at
the center of the slab areas connected to internal
drainage system.
50
4.9B INVERTED BUILT-UP
ROOFING SYSTEM

Also known as upside down roof assembly, an This roofing system is based on the theory
inverted built-up roofing system consists of that the insulation set above the roofing both
several layers installed in a sequence as shown in insulates the building and protects the built-
sketch. First a standard built-up roofing (without up roofing from the harmful effects of thermal
insulation and vapor barrier) is applied directly cycling, ultraviolet degradation, weathering
to the concrete deck. Then, rigid insulation that and roof traffic. This virtually eliminates the
is impervious to moisture such as extruded common defects caused by these elements such
polystyrene foam is bonded to the top of the as blistering, ridging, cracking, alligatoring and
built-up roofing with a mopping of steep asphalt. wrinkling, however the inverted built-up roof
A layer of 3/4 inch crushed stone on top of the system is relatively heavier than the conventional
insulation completes the assembly. Gravel or slag built-up roof system due to the increased stone
should not be used because the sharp edges content.
would damage the bare insulation underneath.

51
4.10 ROOF MONITOR

Typical section of monitor roof:

A roof monitor is a structure mounted on the It is generally used when a standard ridge
ridge of the building and is used for ventilation ventilator is not adequate to give the required
purposes. It is fabricated from either cold number of air changes inside the building.
formed channel sections or hot rolled I-sections.

52
4.11 CURVED BUILT UP
MEMBERS
Curved process conducted during
fabrication:
ƒƒ Design and production system is integrated
with that of the building structure, ensuring
on-time delivery.
ƒƒ Accurate detailing and manufacturing
techniques assure correct appearance and
perfect fit at site.
ƒƒ Flanges range from 125mm x 5 mm to
400mm x 16mm.
ƒƒ Depth range from 200mm to 1200mm
ƒƒ Mass production of members with 10m
radius or more.
ƒƒ Variable depth and tapered members
ƒƒ Capability of curvature in three dimensions.

Semi auto curve beam welders:

a. Single Fillet to each flange in one pass

Min Fillet Size = 3mm
Max Fillet Size = 6.Smm
b. Length of Built up member
Min = 200mm
Max = 14000mm
c. Max Flange Thickness = 16 mm
d. Uniform Flange width per member
e. Max Web Taper = 0-10 Meters
f. Max Feed = -120 in\min
i.e= -3048 mm\min -3mm fillet
g. Filler AWS/ASME SF AS.l7 EM13K
Delhi Metro Station, India

Arc - Curved Aircraft Hangar, Yemen Curved Roof, Enma Mall, Bahrain

53
4.12 SECONDARY
MEMBERS

Bracings:
Cold formed members:
The Cable Bracing is a secondary structural
member that ensures the stability of the building Secondary structural framing refers to purlins,
against forces in the longitudinal direction such girts, eave struts, wind bracing, flange bracing,
as wind, cranes and earthquakes. base angles, clips and other miscellaneous
structural parts.
Purlins, girts, and eave struts are cold formed
from steel which has a minimum yield strength
of 345 MPa (50,000 psi) and will conform to the
physical specifications of ASTMA 570 (Grade
50) or ASTM A-653 (Grade 50) or equivalent.

Z - purlin / girt:

Purlins and girts shall be roll formed Z sections, 200 mm deep

with 64 mm flanges shall have a 16 mm stiffening lip formed at
45º to the flange.

Eave strut:

Eave struts are 200 mm deep with a 104 mm wide top flange, a
118 mm wide bottom flange, both are formed parallel to the roof
slope. Each flange has a 24 mm stiffener lip.

C - section:

C- Sections are 200mm deep with a 100mm flange. The flanges

are perpendicular to the web and have a 24mm stiffening lip.

54
CHAPTER 5 : ENGINEERING
DATA
5.1 PURLIN & GIRT
200Z / 250Z - SECTION
PROPERTIES

Minimum Specified Yield Stress Fy= 34.5 Kn/cm2 (50 KSI)

Table of properties for Z section

Deflec- Allowa-
Elastic Allowable
General information tion ble
modulus moment
Section Inertia shear
Girth Area Weight Lx Sx Va Ma Ma* Ma**
(mm) (cm2) (Kg/1m) (cm4) (cm3) (KN) (KN-m) (KN-m) (KN-m)
200Z1 .5 346 5.19 4.07 310.11 26.02 10.90 5.37 3.49 3.76
200Z1.75 346 6.06 4.75 364.43 31 .51 17.35 6.50 4.23 4.55
200Z2.0 346 6.92 5.43 420.87 37.27 25.97 7.69 5.00 5.39
200Z2.5 346 8.65 6.79 520.33 48.80 45.35 10.07 6.55 7.05
250Z2.5 400 10.00 7.85 883.44 67.28 40.28 13.89 6.94 9.72

Section Properties are calculated in accordance with the 2001 Edition

of the American Iron and Steel Institute “Specifications” (A.I.S .I). Updated on 10 January 2003

1. Top Flange : Fully braced

2. Bottom Flange : Fully unbraced
3. Ma: Capacity under Gravity Load
4. Ma*: Wind Uplift for simply supported beam
5. Ma **: Wind Uplift for continuous beam
6. Stress Increment of 33% is not allowed any more

55
5.2 EAVE STRUT - 0.5:10
AND 1:10 SLOPE - SECTION
PROPERTIES

Minimum Specified Yield Stress Fy = 34.5 Kn/

Cm2 (50 Ksi)

Table of properties for eave strut

Allowa- Allowa-
Top in Compression Bot in Compression
ble ble
General Information Slope
Shear Comp. Deflection Allowable Deflection Allowable
Section
Force Force Inertia Moment Inertia Moment
Girth Area Weight Slope Va Pa Deflx Ma Deflx Ma
(mm) (cm2) (Kg/1m) (:10) (KN) (KN) (cm4) (KN-m) (cm4) (KN-m)
200x1 .5 451 6.77 5.31 0.5 10.93 64.51 433.02 6.51 419.04 6.53
200x1 .75 451 7.89 6.20 0.5 17.40 80.29 502.09 8.06 487.52 8.21
200x2.0 451 9.02 7.08 0.5 26.04 97.30 575.48 9.34 561.50 9.57
200x2.5 451 11 .28 8.85 0.5 45.47 135.46 738.70 12.04 694.37 12.42
250x4.0 501 20.04 15.73 0.5 116.34 289.65 1947.42 28.88 1931 .01 29.76
200x1 .5 451 6.77 5.31 1.0 11 .02 64.52 430.59 6.39 419.56 6.44
200x1.75 451 7.89 6.20 1.0 17.54 80.30 499.67 7.76 488.34 8.18
200x2.0 451 9.02 7.08 1.0 26.25 97.31 572.24 8.99 562.69 9.54
200x2.5 451 11 .28 8.85 1.0 45.82 135.48 735.84 11 .59 693.44 12.37
250x4.0 501 20.04 15.73 1.0 117.03 289.87 1942.95 28.11 1927.81 29.37

Section Properties are calculated in accordance 1. Section is considered fully braced

with the 2001 Edition of the American Iron and 2. Stress Increment of 33% is NOT ALLOWED
Steel Institute “Specifications” (A.I.S.I). Updated ANY MORE
on 10 January 2003

56
5.3 COLD FORMED ‘C’
SECTIONS - SECTION
PROPERTIES

Minimum Specified Yield Stress Fy = 34.5 Kn/Cm2 (50 Ksi)

Table of properties for C section
Deflection Elastic Allowable Allowable
General Information
Interia Modulus Shear Moment
Section
Girth A B C Area Weight lx Sx Va Ma Ma* Ma**
(mm) (mm) (cm2) (Kg/1m) (cm4) (cm3) (KN) (KN-m) (KN-m) (KN-m)
100x50C1 .5 226 100 50 24 3.38 2.66 54.21 10.54 16.33 2.18 1.31 1.31
1 00x50C1. 7 5 226 100 50 24 3.95 3.10 62.54 12.63 20.25 2.61 1.56 1.56
100x50C2.0 226 100 50 24 4.51 3.54 70.68 14.27 23.01 2.95 1.77 1.77
100x50C2.5 226 100 50 24 5.64 4.43 86.37 17.44 28.44 3.60 2.16 2.16
1 00x50DC1.5 226 100 50 24 6.77 5.31 108.43 21 .08 32.65 4.35 2.61 2.61
100x50DC1 .75 226 100 50 24 7.89 6.20 125.09 25.25 40.50 5.21 3.13 3.13
1 00x50DC2.0 226 100 50 24 9.02 7.08 141 .35 28.54 46.02 5.89 3.53 3.53
1 00x50DC2.5 226 100 50 24 11.28 8.85 172.74 34.88 56.88 7.20 4.32 4.32
200x 1 OOC1 .5 451 200 100 35 6.77 5.31 412.67 32 .97 10.90 6.81 4.08 4.08
200x1 OOC1 .75 451 200 100 35 7.89 6.20 493.73 42.33 17.35 8.74 5.24 5.24
200x1 OOC2.0 451 200 100 35 9.02 7.08 577.30 50.78 25.97 10.48 6.29 6.29
200x1 OOC2.5 451 200 100 35 11.28 8.85 730.54 68.14 45.35 14.07 8.44 8.44
200x1 OODC1 .5 451 200 100 35 13.53 10.62 825.34 65.94 21 .80 13.61 8.17 8.17
200x1 OODC1 .75 451 200 100 35 15.79 12.39 987.45 84.65 34.70 17.48 10.49 10.49
200x1 OODC2.0 451 200 100 35 18.04 14.16 1154.61 101.57 51 .94 20.97 12.58 12.58
200x1 OODC2.5 451 200 100 35 22.55 17.70 1461 .08 136.28 90.70 28.13 16.88 16.88
250x80C1 .5 440 250 80 24 6.60 5.18 617.34 40.22 8.63 8.30 4.98 4.98
250x80C1 .75 440 250 80 24 7.70 6.04 727.55 50.37 13.73 10.40 6.24 6.24
250x80C2.0 440 250 80 24 8.80 6.91 826.83 59.31 20.54 12.24 7.35 7.35
250x80C2.5 440 250 80 24 11.00 8.64 1021 .94 77.49 40.28 16.00 9.60 9.60
250x80DC1.5 440 250 80 24 13.20 10.36 1234.68 80.43 17.26 16.60 9.96 9.96
250x80DC1 .75 440 250 80 24 15.40 12.09 1455.10 100.73 27.46 20.79 12.48 12.48
250x80DC2.0 440 250 80 24 17.60 13.82 1653.65 118.63 41 .08 24.49 14.69 14.69
250x80DC2.5 440 250 80 24 22.00 17.27 2043.88 154.98 80.56 31.99 19.20 19.20

1. Top Flange: Fully braced

Section Properties are calculated in accordance 2. Bottom Flange: Fully unbraced
with the 2001 Edition 3. Ma : Capacity under Gravity Load
of the American Iron and Steel Institute 4. Ma* Wind Uplift for sim ply supported beam
“Specifications” (AI.S.I ). Updated on 10 January 5. Ma**: Wind Uplift for continuous beam
2003 6. Stress Increment of 33% is NOT ALLOWED
ANY MORE
* not applicable for 100x50DC

57
5.4 BASE AND CAP CHANNEL
- SECTION PROPERTIES

Minimum Specified Yield Stress Fy= 34 .5 Kn/cm2 (50 Ksi)

Table of properties for cap channel

Deflection Elastic Allowable Allowable
General Information Moment
Inertia Modulus Shear
Section
Girth Area Weight Def lx Sx Va Ma Ma* Ma**
(mm) (cm2) (Kg/lm) (cm4) (cm3) (KN) (Kn-m) (KN-m) (KN-m)
206x76C01.5 346 5.19 4.07 264.65 17.39 10.56 3.59 2.15 2.15
206x76CO1.75 346 6.06 4.75 313.45 23.65 16.82 4.88 2.93 2.93
206x76CO2.0 346 6.92 5.43 365.37 29.30 25.17 6.05 3.63 3.63
206x76CO2.5 346 8.65 6.79 476.88 38.86 45.35 8.02 4.81 4.81

Section Properties are calculated in accordance 1. Top Flange: Fully braced

with the 2001 Edition 2. Bottom Flange: Fully unbraced
of the American Iron and Steel Institute 3. Ma: Capacity under Gravity Load
“Specifications” (A.I.S.I). Updated on 10 January 4. Ma*: Wind Uplift for simply supported beam
2003 5. Ma**: Wind Uplift for continuous beam
6. Stress Increment of 33% is not allowed any
more

58
5.5 KIRBY - RIB, ROOF &
LINER SHEETING ( KR )
SECTION PROPERTIES &
LOAD TABLES ( STEEL )

Pull out Pull over

Fastener Data Sheet Purlin Thickness (mm) 1.50 1.75 2.00 2.50 Panel Thickness (mm) 0.50 0.60 0.70
Ultimate Pull Out (KN) 1.16 1.83 2.09 2.32 Ultimate Pull Over (KN) 5.12 5.72 6.67

Minimum specified yield stress fy = 34.5 Kn/cm 2 (50 ksi)

Steel panel properties (KR)

Panel Shear & Web
Top Flat in Compression Bot Flat in Compression
Nominal Crp
Thickness Girth Weight Va Pa (Def) lx Sx (top) Sx (bot) Ma (Def) lx Sx (top) Sx (bot) Ma
(mm) (mm) (kg/m2) (KN) (KN) (cm4) (cm3) (cm3) (KN-m) (cm4) (cm3) (cm3) (KN-m)
0.5 1145 3.93 5.39 3.27 4.82 1.45 7.10 0.30 4.12 1.75 3.12 0.36
0.6 1145 4.83 8.88 4.96 5.99 2.04 8.71 0.42 5.38 2.19 4.78 0.45
0.7 1145 5.73 13.11 5.91 7.28 2.75 10.69 0.57 6.92 2.72 7.18 0.56

Section Properties are Calculated in accordance Steel Institute “Specifications” (AI.S.I). Updated
with the 2001 Edition of the American Iron and on 10 January 2003

Allowable Uniform Load (Kn/m2)

Panel Nominal Load Purlin
Thickness Case Thick Span (m)
(mm) (-) (mm) 1.00 1.20 1.40 1.50 1.60 1.75 2.00 2.20
D+L - 2.32 1.78 1.41 1.27 1.15 1.00 0.81 0.70
Roof system Allowable WP - 2.32 1.78 1.41 1.27 1.15 1.00 0.81 0.70
Capacity (KN/m2) based WS 1.50 1.55 1.29 1.11 1.03 0.97 0.88 0.74 0.61
0.5
on 3 spans and WS 1.75 2.44 2.00 1.48 1.30 1.14 0.96 0.74 0.61
3 fasteners per lm WS 2.00 2.79 2.00 1.48 1.30 1.14 0.96 0.74 0.61
WS 2.50 2.83 2.00 1.48 1.30 1.14 0.96 0.74 0.61
D+L - 3.22 2.45 1.93 1.73 1.57 1.36 1.09 0.92
Roof system Allowable WP - 3.22 2.45 1.93 1.73 1.57 1.36 1.09 0.92
0.6 Capacity (KN/m2) based WS 1.50 1.55 1.29 1.11 1.03 0.97 0.88 0.77 0.70
on 3 spans and WS 1.75 2.44 2.04 1.74 1.63 1.53 1.36 1.04 0.86
3 fasteners per lm WS 2.00 2.79 2.33 1.99 1.84 1.62 1.36 1.04 0.86
WS 2.50 3.10 2.58 2.11 1.84 1.62 1.36 1.04 0.86
D+L - 3.92 2.99 2.36 2.12 1.91 1.66 1.34 1.14
Roof system Allowable WP - 3.92 2.99 2.36 2.12 1.91 1.66 1.34 1.14
0.7 Capacity (KN/m2) based WS 1.50 1.55 1.29 1.11 1.03 0.97 0.88 0.77 0.70
on 3 spans and WS 1.75 2.44 2.04 1.74 1.63 1.53 1.40 1.22 1.11
3 fasteners per lm WS 2.00 2.79 2.33 1.99 1.86 1.74 1.60 1.40 1.16
WS 2.50 3.10 2.58 2.21 2.07 1.94 1.77 1.41 1.16

1. D+L : Dead Load + Live Load.

2. Deflection Criteria L/240 for D+L
3. Web Crippling is based on a minium Flange
Width of 100 mm
59
5.6 KIRBY - RIB, ROOF &
LINER SHEETING ( KR )
SECTION PROPERTIES &
LOAD TABLES ( ALUMINUM )

Pull out Pull over

Fastener Data
Purlin Thickness (mm) 1.50 1.75 2.00 2.50 Panel Thickness (mm) 0.50 0.70
Sheet
Ultimate Pull Out (KN) 1.16 1.83 2.09 2.32 Ultimate Pull Over (KN) 2.15 2.80
Minimum Specified Yield Stress Fy = 14.49 Kn/Cm 2 (21 Ksi)
ALUMINUM PANEL PROPERTIES (KR)
Panel
Shear & Web Crp Top Flat in Compression Bot Flat in Compression
Nominal
Thickness Girth Weight Va Pa (Def) lx Sx (top) Sx (bot) Ma (Def) lx Sx (top) Sx (bot) Ma
(mm) (mm) (kg/m2) (KN) (KN) (cm4) (cm3) (cm3) (KN-m) (cm4) (cm3) (cm3) (KN-m)
0.5 1145 1.55 3.09 1.93 5.76 1.81 8.44 0.16 5.03 2.10 4 .09 0.18
0.7 1145 2.11 5.81 3.48 7.98 3.00 11 .66 0.26 7.58 2.97 7.83 0.26
Section Properties are Calculated in accordance
with the 2001 Edition of the American Iron and Steel
Institute “Specifications” (AI.S.I). Updated on 10
January 2003
Allowable uniform load (Kn/m2)
Panel Nominal Load Purlin
Thickness Case Thick Span (m)
(mm) (-) (mm) 1.00 1.20 1.40 1.50 1.60 1.75 2.00 2.20
Roof system Allowable D+L - 1.28 0.97 0.77 0.69 0.62 0.54 041 0.31
Capacity (KN/m2) WP - 1.28 0.97 0.77 0.69 0.62 0.54 0.44 0.37
based on 3 spans and WS 1.50 1.50 1.06 0.78 0.69 0.60 0.51 0.39 0.32
0.5
3 fasteners per lm WS 1.75 1.50 1.06 0.78 0.69 0.60 0.51 0.39 0.32
WS 2.00 1.50 1.06 0.78 0.69 0.60 0.51 0.39 0.32
WS 2.50 1.50 1.06 0.78 0.69 0.60 0.51 0.39 0.32
D+L - 2.04 1.54 1.20 1.08 0.97 0.83 0.56 0.42
Roof system Allowable WP - 2.04 1.54 1.20 1.08 0.97 0.83 0.64 0.53
0.7 Capacity (KN/m2) based WS 1.50 1.55 1.29 1.11 1.03 0.97 0.84 0.64 0.53
on 3 spans and WS 1.75 2 .44 1.76 1.30 1.14 1.00 0.84 0.64 0.53
3 fasteners per lm WS 2.00 2.51 1.76 1.30 1.14 1.00 0.84 0.64 0.53
WS 2.50 2.51 1.76 1.30 1.14 1.62 0.84 0.64 0.53

1. D+L : Dead Load + Live Load WP.· Wind 4. Fasteners Uplift Capacity is based on the
Pressure WS.· Wind Suction manufacturer’s Pull Out and Pull Over Data
2. Minumum deflection = Span/180 for D+L
3. Stress Increment of 33% is not allowed any
more

60
5.7 KIRBY WALL SHEETING
( KW)
SECTION PROPERTIES &
LOAD TABLES ( STEEL )
Pull out Pull over
Fastener
Purlin Thickness (mm) 1.50 1.75 2.00 2.50 Panel Thickness (mm) 0.50 0.60 0.70
Data Sheet
Ultimate Pull Out (KN ) 1.16 1.83 2.09 2.32 Ultimate Pull Over (KN) 5.12 5.72 6.67
Minimum specified yield stress Fy = 34.5 KN/cm 2 (50 KSI)
Aluminum panel properties (Kr)
Panel Nom- Shear & Web
Top Flat in Compression Bot Flat in Compression
inal Crp
Thickness Girth Weight Va Pa (Def) lx Sx (top) Sx (bot) Ma (Def) lx Sx (top) Sx (bot) Ma
(mm) (mm) (kg/m2) (KN) (KN) (cm ) 4
(cm )
3
(cm ) 3
(KN-m) (cm ) 4
(cm )
3
(cm ) 3
(KN-m)
0.5 1145 3.93 6.62 3.84 1.74 1.00 1.43 0.21 2.36 1.93 1 .46 0.30
0.6 1145 4.83 9.03 5.78 2.34 1.36 1.80 0.28 3.01 2.45 1.91 0.39
0.7 1145 5.73 11.41 6.89 2.79 1.77 2.17 0.37 3.59 2.96 2.38 0.49

Section Properties are Calculated in accordance Institute “Specifications” (A.I.S.I). Updated on 1 0

with the 2001 Edition of the American Iron and Steel January 2003

Allowable uniform load (Kn/m2)

Panel Nominal Load Purlin
Thickness Case Thick Span (m)
(mm) (-) (mm) 1.00 1.20 1.40 1.50 1.60 1.75 2.00 2.20
Wall system Allowable D+L - 2.32 1.67 1.05 0.86 0.71 0.54 0.36 0.27
Capacity (KN/m 2) based WP - 2.32 1.75 1.32 1.15 1.01 0.81 0.54 0.41
on 3 spans and WS 1.50 1.55 1.29 1.05 0.91 0.80 0.67 0.51 0.43
0.5
3 fasteners per lm WS 1.75 2.03 1.42 1.05 0.91 0.80 0.67 0.51 0.43
WS 2.00 2.03 1.42 1.05 0.91 0.80 0.67 0.51 0.43
WS 2.50 2.03 1.42 1.05 0.91 0.80 0.67 0.51 0.43
D+L - 3.24 2.25 1.42 1.15 0.95 0.73 0.49 0.37
Wall system Allowable WP - 3.24 2.44 1.79 1.56 1.37 1.09 0.73 0.55
06 Capacity (KN/m 2 ) based WS 1.50 1.55 1.29 1.11 1.03 0.97 0.88 0.70 0.58
on 3 spans and WS 1.75 2.44 1.93 1.42 1.24 1.09 0.91 0.70 0.58
3 fasteners per lm WS 2.00 2.76 1.93 1.42 1.24 1.09 0.91 0.70 0.58
WS 2.50 2.76 1.93 1.42 1.24 1.09 0.91 0.70 0.58
D+L - 3.96 2.69 1.69 1.38 1.13 0.87 0.58 0.44
Wall system Allowable WP - 3.96 2.98 2.33 2.03 1.70 1.30 0.87 0.65
Capacity (KN/m 2 ) based WS 1.50 1.55 1.29 1.11 1.03 0.97 0.88 0.77 0.70
07
on 3 spans and WS 1.75 2.44 2.04 1.74 1.61 1.42 1.19 0.91 0.75
3 fasteners per lm WS 2.00 2.79 2.33 1.85 1.61 1.42 1.19 0.91 0.75
WS 2.50 3.10 2.51 1.85 1.61 1.42 1.19 0.91 0.75

1. D+L : Dead Load + Live Load

2. Deflection Criteria L/240 for D+L
3. Web Crippling is based on a minium Flange
Width of 100 mm

61
5.8 KIRBY WALL
SHEETING ( KW) SECTION
PROPERTIES & LOAD
TABLES (ALUMINUM)

Pull out Pull over

Fastener Data
Purlin Thickness (mm) 1.50 1.75 2.00 2.50 Panel Thickness (mm) 0.50 0.70
Sheet
Ultimate Pull Out (KN) 1.16 1.83 2.09 2.32 Ultimate Pull Over (KN ) 2.15 2.80
Minimum Specified Yield Stress Fy = 14.49 Kn/Cm 2 (21 Ksi)

Aluminum panel properties (KR)

Panel Nom- Shear & Web
Top Flat in Compression Bot Flat in Compression
inal Crp
Thickness Girth Weight Va Pa (Def) lx Sx (top) Sx (bot) Ma (Def) lx Sx (top) Sx (bot) Ma
(mm) (mm) (kg/m ) 2
(KN) (KN) (cm )
4
(cm )
3
(cm )
3
(KN-m) (cm ) 4
(cm )
3
(cm )
3
(KN-m)
0.5 1145 1.55 3.54 2.26 2.11 1.22 1.71 0.11 2.83 2.31 1.76 0.15
0.7 1145 2.11 4.92 4.03 3.49 1.92 2.37 0.17 3.94 3.22 2.59 0.23
Section Properties are calculated in accordance
with the 2001 Edition of the American Iron and
Steel Institute “Specifications” (AI.S.I). Updated
on 10 January 2003
Allowable uniform load (Kn/m2)
Panel Nominal Load Purlin
Thickness Case Thick Span (m)
(mm) (-) (mm) 1.00 1.20 1.40 1.50 1.60 1.75 2.00 2.20
Wall system Allowable D+L - 1.19 0.69 0.43 0.35 0.29 0.22 0.15 0.11
Capacity (KN/m 2) based WP - 1.26 0.92 0.65 0.53 0.44 0.33 0.22 0.17
on 3 spans and WS 1.50 1.04 0.73 0.54 0.47 0.41 0.34 0.26 0.22
0.5
3 fasteners per lm WS 1.75 1.04 0.73 0.54 0.47 0.41 0.34 0.26 0.22
WS 2.00 1.04 0.73 0.54 0.47 0.41 0.34 0.26 0.22
WS 2.50 1.04 0.73 0.54 0.47 0.41 0.34 0.26 0.22
D+L - 1.97 1.14 0.72 0.58 0.48 0.37 0.25 0.18
Wall system Allowable WP - 2.01 1.45 1.06 0.87 0.72 0.55 0.37 0.28
Capacity (KN/m2) based WS 1.50 1.55 1.14 0.84 0.73 0.65 0.54 0.41 0.31
0.7
on 3 spans and WS 1.75 1.63 1.14 0.84 0.73 0.65 0.54 0.41 0.31
3 fasteners per lm WS 2.00 1.63 1.14 0.84 0.73 0.65 0.54 0.41 0.31
WS 2.50 1.63 1.14 0.84 0.73 0.65 0.54 0.41 0.31

1. D+L ·Dead Load+ Live Load WP · Wind 4. Fasteners Uplift Capacity is based on the
Pressure WS: Wind Suction manufacturer’s Pull Out and Pull Over Data
2. Minimum deflection= Span/180 for D+L
3. Stress Increment of 33% is not allowed any
more

62
5.9A KIRBY STANDARD
STEEL PANEL
( KCS 40-200)

Pull out Pull over

Fastener Data
Purlin Thickness (mm) 1.50 1.75 2.00 2.50 Panel Thickness (mm) 0.50 0.60
Sheet
Ultimate Pull Out (KN) 1.16 1.83 2.09 2.32 Ultimate Pull Over (KN ) 5.12 5.72
Minimum Specified Yield Stress fy = 34.5 KN/cm2 (50 KSI)

Steel panel properties (KR)

Panel Nom- Shear & Web
Top Flat in Compression Bot Flat in Compression
inal Crp
Thickness Girth Weight Va Pa (Def) lx Sx (top) Sx (bot) Ma (Def) lx Sx (top) Sx (bot) Ma
(mm) (mm) (kg/m ) 2
(KN) (KN) (cm )
4
(cm )
3
(cm )
3
(KN-m) (cm ) 4
(cm )
3
(cm ) 3
(KN-m)
0.5 1219 4.19 6.97 5.29 9.54 2.71 8.33 0.56 8.23 3.25 4.59 0.67
0.6 1219 5.14 13.44 8.12 12.55 2.65 6.15 0.80 10.96 4.16 6.54 0.86

Section Properties are Calculated in accordance

with the 2001 Edition of the American Iron and
Steel Institute “Specifications” (A.I.S.I). Updated
on 10 January 2003.

Allowable uniform load (Kn/m2)

Panel Nominal Load Purlin
Thickness Case Thick Span (m)
(mm) (-) (mm) 1.00 1.20 1.40 1.50 1.60 1.75 2.00 2.20
Roof system Allowable D+L - 3.97 3.07 2.45 2.21 2.01 1.75 1.42 1.22
Capacity (KN/m2) based WP - 3.97 3.07 2.45 2.21 2.01 1.75 1.42 1.22
on 3 spans and WS 1.50 2.58 2.15 1.84 1.72 1.61 1.47 1.29 1.13
0.5
5 fasteners per lm WS 1.75 2.58 2.15 1.84 1.72 1.61 1.47 1.29 1.13
WS 2.00 2.58 2.15 1.84 1.72 1.61 1.47 1.29 1.13
WS 2.50 2.58 2.15 1.84 1.72 1.61 1.47 1.29 1.13
Roof system Allowable D+L - 5.65 4.33 3.43 3.09 2.80 2.43 1.96 1.68
Capacity (KN/m2) based WP - 5.65 4.33 3.43 3.09 2.80 2.43 1.96 1.68
0.6 on 3 spans and WS 1.50 2.58 2.15 1.84 1.72 1.61 1.47 1.29 1.17
5 fasteners per lm WS 1.75 2.58 2.15 1.84 1.72 1.61 1.47 1.29 1.17
WS 2.50 2.58 2.15 1.84 1.72 1.61 1.47 1.29 1.17

1. D+L: Dead Load + Live Load WP: Wind 4. Fasteners Uplift Capacity is based on the
Pressure WS: Wind Suction manufacturer’s Pull Out and Pull Over Data
2. Minumum deflection = Span/180 for D+L
3. Stress Increment of 33% is not allowed any
more

63
5.9B KIRBY STANDARD
ALUMINUM PANEL
( KCS 40-200)

Pull out Pull over

Fastener Data
Purlin Thickness (mm) 1.50 1.75 2.00 2.50 Panel Thickness (mm) 0.50 0.70
Sheet
Ultimate Pull Out (KN) 1.16 1.83 2.09 2.32 Ultimate Pull Over (KN ) 2.15 2.8
Minimum Specified Yield Stress fy = 14.5 KN/cm2 ( 21 KSI)

Aluminum panel properties (KR)

Panel Nom- Shear & Web
Top Flat in Compression Bot Flat in Compression
inal Crp
Thickness Girth Weight Va Pa (Def) lx Sx (top) Sx (bot) Ma (Def) lx Sx (top) Sx (bot) Ma
(mm) (mm) (kg/m ) 2
(KN) (KN) (cm )
4
(cm )
3
(cm )
3
(KN-m) (cm ) 4
(cm )
3
(cm ) 3
(KN-m)
0.5 1219 1.62 4.29 3.28 11.91 3.51 10.12 0.30 10.40 4.01 5.97 0.35
0.7 1219 2.25 10.95 6.29 17.07 5.87 14.01 0.51 15.96 5.85 10.28 0.51

Section Properties are Calculated in accordance

with the 2001 Edition of the American Iron and
Steel Institute “Specifications” (A.I.S.I). Updated
on 10 January 2003.

Allowable uniform load (Kn/m2)

Panel Nominal Load Purlin
Thickness Case Thick Span (m)
(mm) (-) (mm) 1.00 1.20 1.40 1.50 1.60 1.75 2.00 2.20
Roof system Allowable D+L - 2.29 1.75 1.39 1.25 1.13 0.98 0.80 0.63
Capacity (KN/m2) based WP - 2.29 1.75 1.39 1.25 1.13 0.98 0.80 0.68
on 3 spans and WS 1.50 2.58 1.99 1.49 1.30 1.15 0.97 0.74 0.62
0.5
5 fasteners per lm WS 1.75 2.58 1.99 1.49 1.30 1.15 0.97 0.74 0.62
WS 2.00 2.58 1.99 1.49 1.30 1.15 0.97 0.74 0.62
WS 2.50 2.58 1.99 1.49 1.30 1.15 0.97 0.74 0.62
Roof system Allowable D+L - 3.85 2.91 2.29 2.05 1.85 1.59 1.20 0.90
Capacity (KN/m2) based WP - 3.85 2.91 2.29 2.05 1.85 1.59 1.26 1.04
on 3 spans and WS 1.50 2.58 2.15 1.84 1.72 1.81 1.47 1.26 1.04
0.7
5 fasteners per lm WS 1.75 2.58 2.15 1.84 1.72 1.81 1.47 1.26 1.04
3 fasteners per lm WS 2.00 2.58 2.15 1.84 1.72 1.81 1.47 1.26 1.04
WS 2.50 2.58 2.15 1.84 1.72 1.81 1.47 1.26 1.04

1. D+L: Dead Load + Live Load WP: Wind 4. Fasteners Uplift Capacity is based on the
Pressure WS: Wind Suction manufacturer’s Pull Out and Pull Over Data
2. Minumum deflection = Span/180 for D+L
3. Stress Increment of 33% is not allowed any
more

64
5.10A KIRBY DECKING ( KD),
LIGHT DECKING
SECTION PROPERTIES &
LOAD TABLES

Minimum Specified Yield Stress Fy = 34.5 Kn/Cm2

(50 KSI)
Steel deck properties (KD)
Panel Shear & Web Crp Top Flat in Compression Bot Flat in Compression
Nominal
Thickness Girth Weight Va Pa (Def) lx Sx (top) Sx (bot) Ma (Def) lx Sx (top) Sx (bot) Ma
(mm) (mm) (kg/m ) 2
(KN) (KN) (cm ) 4
(cm )
3
(cm )
3
(KN-m) (cm )
4
(cm )
3
(cm ) (KN-m)
3

0.5 1145 4.80 10.55 8.46 7.94 5.72 2.64 0.54 8.10 7.75 2.24 0.46
0.6 1145 5.89 18.43 12.65 10.24 7.82 3.33 0.69 10.55 9.51 3.05 0.63
0.7 1145 6.99 26.19 17.54 12.55 10.10 4.03 0.83 12.56 11.28 3.95 0.81

Section Properties are calculated in accordance

with the 2001 Edition of the American Iron and
Steel Institute “Specifications” (AI.S.I). Updated
on 10 January 2003

Allowable uniform load (Kn/m2)

Panel Type
Thickness of Span (m)
(mm) Span 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90
2 Spans 4.23 3.62 3.09 2.64 2.28 1.99 1.75 1.55 1.38 1.24
0.5
>3 Spans 5.10 4.37 3.79 3.27 2.83 2.47 2.18 1.93 1.72 1.55
2 Spans 5.95 5.02 4.22 3.60 3.11 2.71 2.39 2.12 1.89 1.70
0.6
>3 Spans 7.19 6.15 5.26 4.49 3.88 3.38 2.98 2.64 2.36 2.12

NOTES:

1- Deck Panel must be designed to width stand the concrete net weight of 0.5 Kn/m2 construction load
2- Deflection Criteria L/240 for D+L
3- Web Cripling is based on a minimum Flange Width of 100 mm
4- Allowable uniform load for KD0.7 is available on next page

65
5.10B KIRBY DECK PANELS
KD 40-200 AND KD 0.7
LOAD TABLES
Kirby deck panels are designed in accordance with 1219mm coil unlike the KR, KW and KD panels which
the 2001 Edition of the American Iron and Steel Insti- are made from 1145mm coil.
tute Specifications (A.I.S.I.).
KD 0.7: The profile is the same as KD 0.5 and 0.6 deck
KD 40-200: The application of KCS 40-200 panel panels. Panel thickness is 0.7mm and is made from
has been extended to mezzanine deck panels. The 1145mm coil. Refer to Section 5.10A on Page 65 for
thickness available is 0.7mm. This panel is made from section properties.

Material Specification and Sizes:

1. The KD 40-200 and KD 0.7 are available in

steel only.
2. The specific yield stress for steel = Fy = 34.5
KN/cm2 as per ASTM A792 GRADE 50 or
ASTM A653 GRADE 50
3. The steel panel thickness is 0.7 mm.
4. KD 40-200 and KD 0.7 are available as
galvanized or AluZinc based on availability.
5. Deflection limited to l / 240 for gravity loads.

Allowable uniform load (Kn/m2zz)

Deck Panel Span (m)
Type 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.75 1.8 1.9 2 2.2
KD 40-200 7.67 6.65 5.83 5.16 4.60 4.12 3.72 3.38 3.22 3.08 2.95 2.82 2.19
KD 0.7 9.27 7.93 6.82 5.82 5.03 4.38 3.86 3.42 3.23 3.05 2.74 2.38 1.79

NOTES:

1. Deck panel must be designed to withstand 3. F

or panel thickness of 0.5mm & 0.6mm
Concrete Wet Weight + 0.5 kN/m2 properties, check Kirby Decking (KD) Section
construction load Properties & Load Tables on Chapter 5.10a
2. The type of span is equal or greater than 3
continuous spans.

66
5.11 KIRBY INSULATED SANDWICH
PANELS ROOF,
WALL & PARTITION PANEL

ƒƒ N
.T. - Nominal Thickness / P.U. Core Thickness
ƒƒ T.T. - Total Thickness = N.T. + Depth of Panel

67
5.12 KRIP SANDWICH
PANEL

Specifications:
Minimum Specified Yield Stress for Steel Fy = 34.5 kN/cm2 (50 KSI) ASTM A792 Grade 50
Panel Core Specifications are as follows:
Approximate Total Density = 40 kg/m3 Heat Transmission Value = 0.0198 W /m2
Compression Strength (at 10% deformation) = 1.6 kg/cm 2
Compression Modulus = 36 kg/cm2
Shear (with metal sheet) = 1.63 kg/cm2 Shear Modulus = 20.4 kg/cm2
Adhesion to metal sheet = 1.5 kg/cm2 Water Vapour Transmission = 80 g/24h.m2
Water Absorption = 4% in volume Closed Cell Content = 95% (min)
Pull out Pull over
Fastener Data
Purlin Thickness (mm) 1.50 1.75 2.00 2.50 Panel Thickness (mm) 0.50 0.60
Sheet
Ultimate Pull Out (kN) 1.16 1.83 2.09 2.32 Ultimate Pull Out (kN) 5.12 5.72
Thermal Heat Transmission U-Values:
KRIP 40 KRIP 50 KRIP 60 KRIP 75 KRIP 100
BTU /FT2 h.f. 0.085 0.070 0.059 0.048 0.037
KCAL/M2K 0.414 0.340 0.288 0.234 0.179
WATT/M2K 0.482 0.396 0.335 0.273 0.208

Allowable Loading for KRIP (Kn/m2):

Span in meters
1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00 3.25 3.50 3.75 4.00
KRIP 50 6.83 5.47 4.56 3.90 3.42 3.04 2.73 2.48 2.28 2.10 1.95 1.60 1.32
KRIP60 8.20 6.56 5.47 4.69 4.10 3.64 3.28 2.98 2.73 2.54 2.34 2.17 1.79
KRIP 75 10.25 8.20 6.83 5.86 5.13 4.56 4.10 3.37 3.42 3.15 2.93 2.73 2.56
KRIP100 13.66 10.94 9.12 7.80 6.84 6.08 5.46 4.96 4.56 4.20 3.90 3.20 2.64

Allowable LoadIing due to Fasteners Capacity (Kn/m2) ..

Span in meters
1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00 3.25 3.50 3.75 4.00
3 Fasteners/m 3.48 2.78 2.32 1.99 1.74 1.55 1.39 1.27 1.16 1.07 1.00 0.93 0.87
6 Fasteners /m* 6.96 5.56 4.64 3.98 3.48 3.10 2.78 2.54 2.32 2.14 2.00 1.86 1.74
*In case of KRIP 50, please refer to the above Kirby Building Systems reserves the right to make
table values. changes without prior notice KBS-KRIP-2 80811-00
ƒƒ N
.T. - Nominal Thickness / P.U. Core Thickness
ƒƒ T.T. - Total Thickness = N.T. + 32
68
5.13 KWIP SANDWICH
PANEL

Specifications:
Minimum Specified Yield Stress for Steel Fy = 34.5 kN/cm2 (5O KSI) ASTM A792 Grade 5O
Panel Core Specifications are as follows:
Approximate Total Density = 40 kg/m3 Heat Transmission Value = 0.0198 W /m2
Compression Strength (at 10% deformation) = 1.6 kg/cm 2
Compression Modulus = 36 kg/cm2
Shear (with metal sheet) = 1.63 kg/cm2
Shear Modulus = 20.4 kg/cm2
Adhesion to metal sheet = 1.5 kg/cm 2
Water Vapour Transmission = 80 g/24h.m2
Water Absorption = 4% in volume Closed Cell Content = 95% (min)

PaneI StructuraI Properties:

Pull out Pull over
Fastener Data
Purlin Thickness (mm) 1.5o 1.75 2.oo 2.50 Panel Thickness (mm) 0.50 0.60
Sheet
Ultimate Pull Out (kN) 1.16 1.83 2.o9 2.32 Ultimate Pull Out (kN) 5.12 5.72

Thermal Heat Transmission U-Values:

KWIP 40 KWIP 50 KWIP65 KWIP75 KWIP100
BTU /FT2 h.f. 0.071 0.060 0.049 0.043 0.035
KCAL/M2K 0.347 0.293 0.238 0.211 0.170
WATT/M2K 0.404 0.341 0.277 0.246 0.198

Allowable Loading for KWIP 40, 50, 65, 75, 100mm (Kn/m2):
Span In meters
1.00 1.25 1.5 1.75 2.0 2.25 2.5 2.75 3.00 3.25 3.5 3.75 4.00

KWIP 40 5.46 4.38 3.65 3.12 2.74 2.43 2.18 1.98 1.82 1.68 1.56 1.36 1.12
KWIP 50 6.83 5.47 4.56 3.90 3.42 3.04 2.73 2.48 2.28 2.10 1.95 1.70 1.40
KWIP 65 8.88 7.11 5.92 5.08 4.44 3.95 3.55 3.23 2.96 2.73 2.54 2.37 2.20
KWIP 75 10.25 8.20 6.83 5.86 5.13 4.56 4.10 3.37 3.42 3.15 2.93 2.73 2.56
KWIP 100 13.67 10.93 9.11 7.81 6.84 6.08 5.47 4.49 4.56 4.20 3.91 3.64 3.41

Allowable Loading due to Fasteners Capacity (Kn/m2):

Span In meters
1.00 1.25 1.5 1.75 2.0 2.25 2.5 2.75 3.00 3.25 3.5 3.75 4.00

3 Fasteners/m 3.48 2.78 2.32 1.99 1.74 1.55 1.39 1.27 1.16 1.07 1.00 0.93 0.87

6 Fasteners/m 6.96 5.56 4.64 3.98 3.48 3.10 2.78 2.54 2.32 2.14 2.00 1.86 1.74

*In case of KWIP 50, please refer to the previous Kirby Building Systems reserves the right
table values. to make changes without prior notice KBS-
ƒƒ N
.T. - Nominal Thickness / P.U. Core Thickness KWIP-050911-00
ƒƒ T.T. - Total Thickness = N.T. + 26
69
5.14 KCIP SANDWICH
PANEL

Specifications:
Minimum Specified Yield Stress for Steel Fy = 34.5 kN/cm2 (5O KSI) ASTM A792 Grade 50
Panel Core Specifications are as follows:
Approximate Total Density = 40 kg/m3 Heat Transmission Value = 0.0198 W /m2
Compression Strength (at 10% deformation) = 1.6 kg/cm2 Compression Modulus = 36 kg/cm2
Shear (with metal sheet) = 1.63 kg/cm2 Shear Modulus = 20.4 kg/cm2
Adhesion to metal sheet = 1.5 kg/cm2 Water Vapour Transmission = 80 g/24h.m2
Water Absorption = 4% in volume Closed Cell Content = 95% (min)
PaneI Structural Properties:
Pull out Pull over
Fastener Data
Purlin Thickness (mm) 1.5o 1.75 2.oo 2.50 Panel Thickness (mm) 0.50 0.60
Sheet
Ultimate Pull Out (kN) 1.16 1.83 2.o9 2.32 Ultimate Pull Out [kN) 5.12 5.72

Thermal Heat Transmission U-Values:

KCIP 50 KCIP 60 KCIP 75 KCIP 100
BTU /FT2 h.f. 0.077 0.065 0.052 0.038
KCAL/M2K 0.378 0.315 0.252 0.189
WATT/M2K 0.440 0.367 0.293 0.220

Allowable Loading for KCIP (Kn/m2):

Span in meters
1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00 3.25 3.50 3.75 4.00

KCIP 50 6.83 5.47 4.56 3.90 3.42 3.04 2.73 2.48 2.18 1.70 1.40 1.12 0.92
KCIP 60 8.20 6.56 5.47 4.69 4.10 3.64 3.28 2.98 2.73 2.47 1.98 1.62 1.32
KCIP 75 10.25 8.20 6.83 5.86 5.13 4.56 4.10 3.37 3.42 3.15 2.93 2.50 2.08

Allowable Loading due to Fasteners Capacity (Kn/m2):

Span in meters
1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00 3.25 3.50 3.75 4.00

3 Fasteners/m 3.48 2.78 2.32 1.99 1.74 1.55 1.39 1.27 1.16 1.07 1.00 0.93 0.87

6 Fasteners fm* 6.96 5.56 4.64 3.98 3.48 3.10 2.78 2.54 2.32 2.14 2.00 1.86 1.74

* In case of KCIP 50, please refer to the previous Kirby Building Systems reserves the right
table values. to make changes without prior notice KBS-
KCIP-050911-00

70
5.15 CONCEALED FASTENER
CLADDING
SINGLE SKIN CLADDING - TYPE KC

Features: Benefits:

ƒƒ Single concealed fastener cladding type- kc ƒƒ An attractive architectural look for

is used for exterior wall cladding and interior commercial and Institutional buildings .
roof and wall Liner panels . ƒƒ Flat surface without exposed fasteners & no
ƒƒ Panels have interlocking tongue & groove corrugation .
joints. ƒƒ For external panel only.
ƒƒ Supplied in covering widths of 333mm &
666mm with Thickness of 0.5 And 0.6Mm .
ƒƒ Available in all kirby standard colours.

71
5.16 CONCEALED FASTENER
SINGLE SKIN CLADDING
TYPE ( KC) SPECIFICATIONS
1.0 GENERAL hexagonal heads and shall be zinc plated and
1.1 The Kirby concealed fastener panel system color coated to match the panel colors.
type ‘KC’ shall be furnished with other 5.2 No panel to panel fasteners are required .
integral components to form the exterior All fasteners shall be made from the outside,
envelope and/or the interior partitions of the hidden in the panel joint thus eliminating
building as described herein. exposed fasteners.
1.2 Installation of the panel system shall be in
accordance with Kirby Building installation 6.0 FLASHINGS AND TRIMS
drawings. 6.1 Flashing and trims shall be furnished at
2.0 PANEL DESCRIPTION corners, eaves, rake, framed openings and
2.1 Exterior wall panels shall be 333mm covering wherever necessary to provide weather
width, 26G or 24G thickness and interlocking tightness and a good finished appearance .
joints to conceal the fasteners to the 6.2 Flashing and trims shall be of the same
structural members within the joints . specifications as the panel materials.
2.2 Interior liner or Partition panels shall be 7.0 ACCESSORIES
either 333mm-26G/24G or 666mm-24G
thickness and interlocking joints to conceal 7.1 Accessories as specified such as doors
the fasteners to the structural members , windows, etc.. , shall be furnished or
within the joints . framed openings provided as shown in the
2.3 Panels shall be precision roll formed at the building installation drawings . Accessories
factory to a total panel depth of 35mm using when supplied shall be to Kirby standard
precoated sheeting coils. specifications unless otherwise noted on
2.4 Panels shall be one piece from base to top of wall building installation drawings.
or partition upto a maximum length of 9 meters. 7.2 Location and type of accessories shall be as
2.5 Both ends of the panel shall be square cut shown in Kirby building installation drawings .
and unpunched.
7.3 Blanket insulation may be used with the
3.0 PANEL MATERIAL AND FINISH panel system. Panel configuration can
3.1 Panel material shall be either zincalum accommodate up to 1OOmm thick, 12 Kg/m3
coated or galvanized steel to ASTM A792 density insulation.
Grade 50B AZ150 or ASTM A653 Grade 50
with G90 coating. 8.0 PACKAGING AND SHIPPING
3.2 The finish coating shall be polyester or 8.1 For shipments, panel faces and corners shall
silicon polyester coating 25 microns on be suitably protected . Panel bundles shall be
exterior face and 10 microns on interior packaged for safe and ease of handling and
face of the panel. Other finish coatings are transport.
available upon request. 9.0 FIELD INSTALLATION
3.3 Panel color shall be one of Kirby standard colors .
Other colors are available upon request. 9.1 Structural system shall be plumb within
4.0 PANEL DESIGN AISC/MBMA tolerances before wall/partition
panels are attached to girts.
4.1 Panel design shall be in accordance with AISI
Cold Formed Steel Design Manual and good 9.2 Sealant shall be applied at panel joints to
engineering practices . ensure weather tightness . Flashing and trim
5.0 FASTENERS shall be installed true and in proper alignment
for best appearance.
5.1 Panels shall be fastened to structural
9.3 All installation shall be done in accordance
members using #14 self tapping screws with
metal and EPDM washers. Screws shall have with Kirby building installation drawings and
good working practices.

72
5.17 CONCEALED
FASTENER INSULATED
CLADDING TYPE KCIP

Features:

ƒƒ Sandwich panel concealed fastener cladding

type-kcip is used for exterior wall cladding
and exterior partition.
ƒƒ Panels have interlocking tongue & groove
joints.
ƒƒ Supplied in covering widths of 666mm &
1000mm and thickness of 0.5 & 0.6Mm ,top
& bottom skin thickness.
ƒƒ Available in all kirby standard colours.

Benefits:

ƒƒ An attractive architectural look for

commercial and Institutional buildings.
ƒƒ Flat surface without exposed fasteners & no
corrugation.
ƒƒ Ideal for internal office & room partitions.

73
5.18 CONCEALED FASTENER
INSULATED PANEL CLADDING
TYPE ( KCIP) SPECIFICATIONS
1.0 GENERAL 5.0 FASTENERS
1.1 The Kirby concealed fastener insulated 5.1 Panels shall be fastened to structural
panel system type 'KCIP' shall be furnished membersusing #14 self tapping screws with
with other integral components to form metal and EDPM washers. Screws shall have
the exterior envelope and/or the interior hexagonal heads and shall be zinc plated and
partitions of the building as described herein. color coated to match the panel colors.
1.2 Installation of the panel system shall be in 5.2 No panel to panel fasteners are required.
accordance with Kirby Building installation All fasteners shall be made from the outside,
drawings. hidden in the panel joint thus eliminating
2.0 PANEL DESCRIPTION exposed fasteners.
2.1 Exterior wall and partition panels shall be 6.0 FLASHINGS AND TRIMS
1000mm covering width and maximum 6.1 Flashing and trims shall be furnished at
possible length(not to exceed 9 meters), to corners, eaves, rake, framed openings and
minimise the number of joints. The panels wherever necessary to provide weather
shall be manufactured by the press injection tightness and a good finished appearance.
method to produce a rigid polyurethane core 6.2 Flashing and trims shall be of the same
of 35 Kg/m3 nominal density between steel specifications as the panel facing materials.
facings. Panels shall have a generally flat
7.0 ACCESSORIES
profile with minor ribs and interlocking joints
to conceal the fasteners to the structural 7.1 Accessories as specified such as doors,
members. windows, etc .. , shall be furnished or framed
2.2 The panels shall be available in nominal openings provided as shown in the building
thickness of 50mm, 60mm, 75mm and 100mm. installation drawings. Accessories when
2.3 Panels shall be one piece from base to top of wall supplied shall be to Kirby standard
or partition upto a maximum length of 9 meters. specifications unless otherwise noted on
2.4 Both ends of the panel shall be square cut building installation drawings.
and unpunched. 7.2 Location and type of accessories shall be as
3.0 PANEL MATERIAL AND FINISH shown in Kirby building installation drawings.
3.1 Panel facings shall be precision roll formed 8.0 PACKAGING AND SHIPPING
from either zincalum coated or galvanized 8.1 For shipments, panel faces and corners shall
steel substrate to ASTM A792 Grade 50B be suitably protected. Panel bundles shall be
AZ150 or ASTM A653 Grade 50 with G90 packaged for safe and ease of handling and
coating. transport.
3.2 The finish coating shall be polyester or 9.0 FIELD INSTALLATION
silicon polyester coating 25 microns on
exterior face and 1 0 microns on interior face 9.1 Structural system shall be plumb within
of the panel facings. Other finish coatings are AISC/MBMA tolerances before wall/
available upon request. partition panels are attached to girts.
3.3 Panel color shall be one of Kirby standard 9.2 Sealant shall be applied at panel joints to
colors. Other colors are available upon ensure weather tightness. Flashing and
request. trim shall be installed true and in proper
4.0 PANEL DESIGN alignment for best appearance.
9.3 All installation shall be done in accordance
4.1 Panel design shall be in accordance with AISI
with Kirby building installation drawings and
Cold Formed Steel Design Manual and good
engineering practices. good working practices.

74
5.19 FIBER GLASS
INSULATED PANEL

WITH EXCELLENT
PERFORMANCE
CHARACTERISTICS

Kimmco
Fiber Glass
FIRE SAFE
Insulation
SUPERB THERMAL
INSULATION

EXCELLENT ACOUSTIC
INSULATION

ENVIRONMENT FRIENDLY

KRGP- fiber glass insulated panel

For roof & wall

COST EFFICIENT
EASY TO INSTALL
SUITABLE TO RETROFIT
COMPATIBLE WITH KIRBY BLDGS

Kimmco
Fiber Glass
Insulation

KFGP- fiber glass insulated panel for partitions

75
5.20 FIBER GLASS
INSULATED PANEL
KRGP
Applications :

As Roof and Wall cladding system on·:

ƒƒ New Pre-engineered steel buildings.
ƒƒ Retrofit applications on
ƒƒ existing steel buildings

Fiber glass insulated panel for roof & wall

Description:
Top facing : Trapezodial profile 32mm deep at
333mm spacing, Steel 26g or 24g.
Bottom facing : Generally flat profile with minor
stiffening ribs at 250 mm spacing, Steel 26g or
24g. The steel facings are high strength steel Dimensions :
to ASTM A 792 grade 345 Mpa with zincalum Length : upto 9000 mm
coating to AZ150. The substrate is polyester width : 1000 mm
coated to 25 microns nominal Thickness : 50,60,70 or
thickness on exposed side and 12 microns on 100 mm at low rib (add 32 mm to thickness at high rib)
reverse side. Available in full range of Kirby
standard colors. Insulation :
FIRE SAFE CFC free fiberglass insulation (which NOTE :
does not emit TOXIC SMOKE) laminated to the
steel facings with special chemical glue, completely Panels in other thickness can also made
filling the insulation cavity. available to meet any specified ‘R’ or ‘U’ value

Performance Values:
ƒƒ Thermal Heat Transmission (U-Value)

Krgp 50 Krgp 60 Krgp 75 Krgp 100

BTU/ft .h.f
2
0.108 0.092 0.076 0.59
W/M .K
2
0.613 0.524 0.431 0.332

ƒƒ Maximum working temperature - 230º C

ƒƒ Fire Safety - Non-combustible
ƒƒ Acoustics - KRGP 60 : STC - 32dB

76
 KFGP
Applications :
ƒƒ AS Interior Partition Panels.
ƒƒ Interior wall liner Panels.

Fiber glass insulated panel for partitions

Description:
Top facing and Bottom facing : Trapezodial profile Dimensions :
32mm deep at 333mm spacing, Steel 26g or 24g. Length : upto 9000mm
Bottom facing : Generally flat profile with minor stiff- width : 1000mm
ening ribs at 250 mm spacing, Steel 26g or 24g. Thickness : 50, 60, 75 or
The steel facings are high strength steel to ASTM A 100 mm
792 grade 345 Mpa with zincalum coating to AZ150.
The substrate is polyester coated to 25 microns NOTE :
nominal thickness on exposed side and 12 microns on
reverseside. Available in full range of Kirby standard Panels in other thickness can also made
colors. available to meet any specified ‘R’ or ‘U’ value
Insulation : Performance Values:
FIRE SAFE CFC free fiberglass insulation (which
does not emit TOXIC SMOKE) laminated to the steel
facings with special chemical glue, completely filling
the insulation cavity.

Performance Values :

ƒƒ Thermal Heat Transmission (U-Value)

Krgp 50 Krgp 60 Krgp 75 Krgp 100

BTU/ft .h.f
2
0.114 0.097 0.079 0.60
W/M .K
2
0.645 0.548 0.447 0.342

ƒƒ Maximum working temperature - 230º C

ƒƒ Fire Safety - Non-combustible
ƒƒ Acoustics - KRGP 100 : STC - 37dB

77
5.21 SELF DRILLING SCREW
( SDS )

Dimensions:

HEAD ACROSS FLATS 9.33 - 9.52 mm

THREAD DIA ( O.D ) 6.10 - 6.25 mm
THREAD DIA ( I. D ) 5.45 - 5.55 mm
EPDM WASHER DIA 19 mm

Pull out (Ultimate)

Purlin Thickness (mm) 1.50 1.75 2.00 2.50
Ultimate Pull Out (KN) 1.16 1.83 2.09 2.32

Pull over (Ultimate)

Panel Material Steel Aluminium
Purlin Thickness (mm) 0.5 0.6 0.5 0.7
Ultimate Pull Over (KN) 5.12 5.72 2.15 2.80

78
5.22 CABLE BRACING

Definition:

The Cable Bracing is a primary member suitable

to insure the stability of the building against
forces in the longitudinal direction due to Wind,
Cranes, Earth Quake ... etc.

Kirby’s Cable Bracing is designed in accordance

with the latest edition of the American Institute
of Steel Construction AISC 2005.

Specifications: Advantages:

1. Cables are made of Galvanized Extra High ƒƒ Higher Strength 60 KN

Strength Seven Strand Cable of 1/2” diameter ƒƒ Better corrosion resistance (Galvanized)
conforming to ASTM A475 - 2003 Class 1 ƒƒ Easy packing and shipping (Round Packing)
(G40). ƒƒ Cable can be fabricated and shipped for any
2. Terminals are made of Galvanized (G40) 25 required length.
mm diameter rods conforming to ASTM A36 ƒƒ Easy building installation.
3. Hill Side Washers are made of Aluminum ƒƒ Light weight (Economical)
Alloy

Revision Date : 01-01-07

79
5.23 ASTM A36 ANCHOR
BOLTS COMPONENT
SECTION PROPERTIES &
LOAD TABLES
Standard specifications bolts:

ASTM designation - A36

Connection Type- N (Bearing type connection
with threads included in shear plane)
Hole Type- STD (Standard round holes)

Fu =58 ksi (39.98 kN/cm2)

Ft = 19.1 ksi (13.16 kN/cm2)
Fv = 9.9 ksi (6.82 kN/cm2)

Anchor Bolt Setting

Table 3.7.1 - Allowable Loads
Bolt L A B C D a Pitch C/s
Le
Diam
mm mm mm mm mm mm mm (P) mm2
16 400 100 75 325 100 545 2.0 201.06
20 500 120 100 400 150 670 2.5 314.16
24 650 140 100 550 150 870 3.0 452.39
32 950 200 100 850 150 1290 3.5 804.24

Allowable Comb. Allowable comb.

Max Corresponding Corresponding Max Pull-out
shear tension shear tension strength
kN kN kN kN kN
13.68 9.90 4.43 26.55 30.13
21.37 15.46 6.91 41.49 46.31
30.78 22.27 9.96 59.75 62.90
54.72 39.59 17.70 106.21 93.26
Effective length, Le = C + A + 8*Bolt diameter - Bolt radius
NOTE:
4. Pull out strength is based on 28 days
1. Shear and tension loads based on gross concrete compressive strength 2.07 kN/cm2
nominal area of bolt. 5. Pull out strength is calculated as per ACI
2. Allowable loads are including combined (American Concrete Institute) Building Code 318.
shear and tension. 6. Bolt specifications based on AISC 2005
3. Stress increase of 33% is NOT ALLOWED Edition.
ANY MORE.
REV DT 07/06/05 07/12/05 24/02/14

80
5.24 ASTM A325 HIGH
STRENGTH BOLTS
COMPONENT SECTION
PROPERTIES & LOAD TABLE
Specifications:

Bolts, Nuts & Washers Finishing

Electro-Galvanized ASTM F 1135M Grade 1
Bolts Specification
Heavy Hex Structural ASTM A325M Type 1
Nuts Specification
Hex ASTM A 563M 10S
Washers Specification (Washers/Bolt)
Hardened Flat ASTM F 436M Type 1

For Detailers:

List the Bolt, Nut and Washers Seperatly in Shipper

List
Add 2% extra (Minimum Extra is 2 Bolts)

Bolts W Min-Max Grip (3 mm Building Allowable Forces

Installation Tolerance)
Nom Bolt Threaded Threads Nom Max Max Combined
Dia Length Length Pitch Thick 0 10 20 30 40 50 60 70 120 Tension S. Shear Tension
mm mm mm mm/Thr mm KN KN KN
18
12 40 Full 1.75 35.06 18.66 10.52
29
16 55 Full 2.00 3.10 62.33 33.18 18.70
39
20 70 Full 2.50 97.39 51.84 29.22
38
75 Full
24 3.00 4.0 58 140.24 74.64 42.07
95 Full
75
30 120 Full 219.12 116.63 65.74
3.50 4.50 73
32 120 Full 249.32 132.70 74.80

* Maximum Grip (including 3mm tolerance) = Bolt Length - 3mm Erection Tolerance - 1 Washer - 1 Nut - (2 x Threads)
X Y Z

X: Minimum Grip For Combined Tension and Shear refer to Table J3.2,
Y: Maximum Grip inluding 3mm erection tolerance and equations:
Z: Maximum Grip excluding 3mm erection tolerance (J3-2), (J3-3a), (J3-3b) from the AISC 2005 Edition

81
5.25 STANDARD CRANE SYSTEM

General:
on center, lathed toa diameter of 200 mm, and
The kirby standard crane system is a single properly aligned in a uniaxial direction, and
girder, pendant operated, top running system equipped with derailment protection suitable
which includes a structural bridge member for travel along rails (aisc 30 lb. Rail) which
fabricated by kirby building systems, and electro- are mounted on crane runway beams which in
mechanical components fabricated by selected turn are supported on shop welded brackets
vendors and supplied as a complete Package. to the frame columns. The rails are aligned by
hook bolts which interlock the flange of the cap
Crane bridge: channel of the crane .Runway beams and through
the adjusting nuts on. Either side of the rail neck.
The structural design of the crane bridge
conforms to the allowable stresses as defined Hoist and trolley:
in the american institute of steel construction
manual. The crane bridge is designed for the The hoisting trolley moves along the bonom
Crane capacity magnified by 10% for impact, flange of the crane bridge, and has special
and the total weight of bridge, hoist and trolley. mounting at which the hoist is bolted. The hoist
Deflection under total load is limited to 0.001 Of is a low headroom type to allow greater lifting
span. The ends of the crane bridge are prepared heights needed particularly in low spaces. The
with special connecting plates which are bolted hoist capacity is rated in accordance with fem
to the end carriage. Field welding is required 1am (federation europeenne de la manutention)
for the connection of bridge to end carriage standards which is based on load spectrum
and for bridges of spans larger than 12m require (% lifting load per % time), average operating
field welded splice to be performed under high time per day, daily working time and starting
quality control to ensure full penetration welds. frequency, and as shown on the following page .
Maximum span supplied with the standard end
carriage is 21 m to control grabbing.
Crane runway beams:
End carriage:
The crane runway beams are oriented in the
longitudinal direction of the crane travel and
The end carriages are made of reinforced consist of h-sections with cap channels, designed
welded box sections. Each end carriage is for maximum combined·stresses generated from
equipped with its separate travelling machinery maximum wheel loads positioned at critical
to eliminate the drawback of a long oscillating locations and acting vertically and Horizontally.
drive shaft. Motors are totally enclosed. The maximum wheel load is magnified by 10%
Insulation class f, protection ip54. The end for impact. The horizontal load is generated from
carriages come with double flange wheels, .3.4M 20% of the sum of the crane capacity and the
weights of hoist and trolley.

82
5.26 STANDARD CRANE
SYSTEM TYPE ‘K’
CLEARANCES & WHEEL LOADS

K I. THE LONGITUDINAL FORCE APPLIED

AT THE TOP OF RAIL, AT EACH WHEEL.
K II. THE LATERAL FORCE OF CRANE RUNWAY DUE TO
EFFECT OF MOVING LOAD AT THE TOP OF RAIL,
AT EACH WHEEL.

Crane C E1 E2 Span of H Wheel loan KD

Capacity M.t. mm mm mm Bridge mm Dyn.max Ki Kii
6 500 21.0 2.1
9 500 23.9 2.39
12 500 26.2 2.62
3.2 660 740 825 1.74
15 750 31.3 3.13
18 750 31.3 3.13
21 800 32.0 3.20
6 500 30.4 3.04
9 500 34.4 3.44
12 500 37.3 3.73
5.0 590 815 790 2.65
15 750 40.7 4.07
18 750 43.2 4.32
21 900 43.6 4.36
6 600 59.9 5.99
9 600 64.2 6.42
12 600 68.0 6.80
10.0 685 1015 1110 5.32
15 850 72.0 7.20
18 900 75.8 7.58
21 1000 77.5 7.75

83
5.27 STANDARD CRANE
SYSTEM TYPE ‘K’ HOIST
DETAILS

Crane Hoist Hoist Ht. Hoisting Cross Dimensions

capacity type Wt. Lift speed travel speed A B C D L
M.t. Kg M M/Min M/Min mm mm mm mm mm
3.2 1221G 340 8 8 20 108 480 660 950 910
5 1441F 400 8 5 20 108 535 590 950 1080

Crane Fem Hoisting motor Wire rope

Capacity M.t. group K.W. % ED NoS. DIA. mm
3.2 1 AM 4.5 30 2 10
5 1 AM 4.5 30 4 10

NOTE :

A. THE TRAVEL SPEED BY 2 STEP POLE

CHANGE MOTOR.

Crane Hoist Ht. Hoisting Cross Dimensions

Capacity Hoist Wt. Lift speed travel speed A B C D L
M.t. type Kg M M/Min M/Min mm mm mm mm mm
10 2441B 850 8 4 20 125 670 685 820 1255

Crane Fem Hoisting motor Wire rope

Capacity M.t. Group K.W. % ED NoS. DIA. mm
10 1 AM 7.5 50 4 14

84
5.28 STANDARD CRANE
SYSTEM TYPE ‘K’ END
CARRIAGE DETAIL

Electrical Specifications:

( FOR 3.2 T , 5.0 T & 10 T )

1. Motor voltage - 380v i 440v
2. Control voltage - 220v
3. Frequency - 3 phase, 50 cis 60 cis
4. Push button pendant control

Type L L1 L2 L3 D H H1 B Long travel speed

M / Min
USP 3680 3400 140 3820 200 325 300 200 32 AND 10
206

85
5.29 STANDARD CRANE
SYSTEM TYPE ‘K’ LOAD
SPECTRUM
Fem group Fem 1Am Fem 2Am Fem 3Am
load spectrum Operating time Hours / Day
LIGHT < =4 4-8 8-16
Light

MEDIUM < =2 2-4 4-8

Medium

HEAVY <= 1 1-2 2-4

Heavy

Severe SEVERE < 0.5

= 0.5-1 1-2

RATED REDUCED REDUCED

CAPACITY CAPACITY CAPACITY
EQUIVALET CRANE
CAPACITIES (TONS)
3.2 2.5 2.0
FOR HIGHER FEM GROUP
CLASSIFICATION 5.0 4.0 3.2

10.0 8.0 6.3

86
5.30 SERVICE LOADS
HANGING DETAILS &
ALLOWABLE LOADS
Service loads may be suspended from the Kirby roof for roof slope upto 10%. Multiple suspended loads
purlins provided that the intensity and location of shall be equi·spaced in a bay.
these loads are pre·defined at time of sales. Only suggested suspension details as shown should
For standard buildings, where service loads are not be used to prevent localized buckling of purlins. For
pre·calculated, the suggested hanging details and heavier auxiliary loads, additional framing members
maximum allowable suspended load table may be will be needed.
used for a specific bay length, purlin size and lap, and The suspension angles and fasteners are not supplied
number of suspended loads per bay. by Kirby.
The recommended suspension details are intended

Maximum allowable suspended load, p ( kg), in addi-

tion to Roof live load of 0.6 Kn / m2

Bay spacing (meter)

6.0 7.5
Purlin Lap
No. of loads / bay No. of loads / bay
1 2 3 4 1 2 3 4
200 Z 107 65 45 30 25 0 0 0 0
1.5
706 130 95 65 50 30 20 15 10
107 140 100 70 55 40 30 20 15
1.8
706 245 180 120 100 105 80 50 45
107 275 205 135 110 145 105 70 60
2.5
706 445 330 220 185 245 185 120 100

87
5.31 VENTILATION
CALCULATION

The number of standard Kirby ridge ventilators and Procedure:

louvers can be determined from following proce-
dure based on a given unit of air changes and known
building geometry.
Using the following nomograph, draw a line con-
necting the known value of air changes per hour
Building volume: and the volume of the building to get the rate of
air flow (cfm-m3/min). Then draw a line connecting
the determined value of the rate of air flow and the
V = W X L X (EH + WS/40) stack height (sh) to find the length of ridge ventilator
W = SPAN, L = LENGTH required, divide the length of ridge ventilator by 3m
EH = EAVE HEIGHT to get the number of kirby standard ridge ventilators.
S = ROOF SLOPE IN TERMS OF 10 Wall openings ( louvers, doors and windows) must be
provided and well distributed. To ensure air inlet and
proper ventilation cycle for each linear meter of ridge
ventilators, one square meter of wall opening for air
Ventilation rates for types of building: inlet is required.

If the required air changes cannot be achieved using

Type Of Building Air Changes / Hour natural ventilation as above, forced ventilation using
power vents may be provided: consult head office
Boiler house/engine room 15-30 for details. Refer to accessories for Kirby’s standard
Living quarters, rooms & louver and ridge ventilator details.
wards 15-20
Classrooms, canteen 5-15
Offices, commercial shops,
factories 5-10

88
5.32 VENTILATION
CALCULATION NOMOGRAPH
NOMOGRAPH
For Determining Ridge Ventilators / Louvers

* Stack Height Is Actual

Distance From Top Of Inlet
15 4-6 Sill To Elevation Of
Ventilator Stack Effect Is
Based On 15°F Temperature
Differential.

89
5.33 KIRBY INSULATION
( KIB-12) INSTALLED “U”
VALUES

At roof with 50 mm insulation At wall with 50 mm insulation

Element Construction Resistance R Element Construction Resistance R
1 Outside surface 0.25 1 Outside surface 0.25
(7.5 Mph wind) 2 Wall sheeting 0.00
2 Roof sheeting 0.00 3 Insulation 50 mm 6.79
3 Insulation 50 mm (@100ºf) 6.79 4 Air space 0.52
EXAMPLE :
4 Air space 1.62 5 Liner 0.00
5 Liner 0.00 6 Inside surface (still air) 1.35
6 Inside surface (still air) 1.10 Total 8.91
Total 9.76

INSULATION INSTALLED VALUES:

AT ROOF WITH 50mm INSULATION AT WALL WITH 50mm INSULATION

U= 1= 1 = 0.102 BTU / HRFt2ºF U= 1= 1 = 0.112 BTU / HRFt2ºF
= 0.500 K Cal / HR M ºC
2
= 0.548 K Cal / HR M2ºC

Table of insulation installed values

Thickness of “U” values
insulation At roof At wall
mm K cal / hr m2 ºc Btu / hr ft2 ºf K cal / hr m2 ºc Btu / hr ft2 ºf
50 0.500 0.102 0.548 0.112
75 0.371 0.076 0.397 0.081
100 0.295 0.060 0.311 0.064
150 0.215 0.044 0.220 0.045

90
5.34 ROOF LIGHTING
REQUIREMENTS
Recommended roof lighting:

Daylight factors recommended for diferent activities

are shown in table below:

In order to obtain the net area of skylights required,

apply a multiplication factor from the
graph to cover variations in wall to floor area ratio and
location.
To allow for possible change in the use of a building, a
daylight factor below 5 % is not recommended. Also
any required daylight factors above 10 % should be
supplemented by local artificial lighting. This minimis-
es the heat transmission from sunlight.

Operation or type of building recommended %

Daylight factor
Warehouses, packing, large assembly heavy forging or casting, 2.0
sawmills
Ordinary bench and machine work, average general lighting, fine 4.0
casting, motor repair, general office work, Indoor tennis.
Drawing work, medium assembly, weaving. small type setting. 6.0
Small inspection and assembly.
Small bench and machine work. 10.0

EXAMPLE :

Building in an industrial area of 30m span x 60m

long x 8m eave ht.
Used as a weaving mill.
Floor area = 30x60 = 1800m2
Wall area = 8x180 = 1440 m2
Floor area = 1.25
Wall area

From table, daylight factor = 6 %

From’ graph m’ultiplication constant = 1.9
,’ . Net area of lighting required = 1.9X6x30x60 = 205 m2
100
Approx. net area of one skylight (3305 lg) = 3 m2
No. of skylights required = 205/3 = 68.33, Say 70 nos.
Use 70 nos. Skylights evenly distributed on each
roof slope.

91
5.35 ROOF DRAINAGE
CALCULATIONS
Drainage calculations: Valley gutters:

The assumed standard rain’fall to’ be used on Kirby Since it would be undesirable to have valley gutters
buildings shall be as follows: overflow even on extreme conditions.
The value of 12 ½ inches per hour shall be used unless
Eave gutters: otherwise specified. The following
appropriate design coefficients may be used to obtain
the size of the gutter.
Since it would not normally cause trouble to have the 12 ½ In/hr = 2.35 Sq. In of valley gutter per
eave gutter overflow under extreme conditions. = 100 sq.ft. of roof area
drained
The value of 7 ½ inches per hour shall be used unless
otherwise specified. The following approximate design
Down spouts:
coefficients may be used to obtain the size of the
gutter. Standard downspouts are provided along each
7½ In/hr = 1.66 Sq. In. of eave gutter per 100 sq. ft. of sidewall at spacing as recommended on roof drainage
roof area drained. reuirements have been based on formula derived by
“The Copper Development Association Inc.” From
tests conducted on level gutters at the U.S. bureau
of standards in washington D.C. The formula are as
follows:

= 28/13 16/13
DOWNSPOUT “S” (U) (M)
(0.4810 28/13 (W1/43200) 10/13

WHEN GUTTER CAPACITY GOVERNS
OR “S” = 1200A
WI WHEN DOWNSPOUT CAPACITY GOVERNS

Where S = downspout spacingin feet

U = average width of gutter (ft)
M = depth/width of gutter
W = width of area being drained (ft)
I = maximum intensity of rainfall (in/hr)
A = area of downspout (sq.In)

The following approximate design coefficient may be used to calculate size of downspouts.

7 ½ 1/2 In/hr = 187.5 Sq.Ft. of roof area drained per so. In of downspout area.

92
5.36 FIRE PROTECTION
SYSTEM
Fire resistant coating mandoval p20 or equal can be
applied to Kirby steel structure to achieve a given fire
rating. Applied by spray, it provides a monolithic tex-
tured finish and has good in· sulation, sound absorp-
tion and bonding properties. The material is factory
Pre-mixed and consists of vermiculite and portland
cement. It does not spall or crack under impact and
also highly resistant to both hot and cold thermal
shocks. Mandolite p-20 contains no asbestos or fibre
content and presents no known health hazard during
or after application. An alkali resistant paint is applied
to the main frames to receive the coating and on gal-
vanised surfaces no special paint is required.

Physical properties (Mandolite p-20)

ƒƒ Density - 320 kg/m3

ƒƒ Bond strength - to bare steel 62 kn/m2
ƒƒ To galvanised steel 59 kn/m2
ƒƒ Compressive strength - 380 kn/m2
ƒƒ Ph value - 12 -12.5
ƒƒ Thermal conductivity - 0.078 Kcal m/m2 hr º c

93
5.37 BUILDING MATERIALS
WEIGHTS
Materials weight Materials weight
Psf kg/m2 PSF kg/m2
Ceilings Roofs
Channel suspended system 1 4.9 Kirby-rib 26g 1 4.8
Accoustical fiber tile 1 4.9 Kirby-rib 24g 1.2 5.9
Partitions 3-Pl y ready roofing 1 4.9
Clay tile 3-Ply felt & gravel 5.5 26.9
31 IN. (76mm) 17 83.0 5-Pl y felt & gravel 6 29.3
4 IN. (100mm) 18 87.9 Shingles
Wood 2 9.8
6 IN. (150mm) 28 136.7
Asphalt 3 14.7
8 IN. (200mm) 34 166.0
Clay tile 9-14 43.9-68.4
10 IN. (250mm) 40 195.3
Slate 1/4 in. (6mm) 10 48.8
Gypsum block Sheathing
21 IN. 9.5 46.4 Wood 3/4 in. (19mm) 3 14.7
31 IN. 10.5 51 .3 Gypsum 1 in. (25mm) 4 19.5
41 IN. 12.5 61.0 Insulation 1 in.(25mm)
51 IN. 14.0 68.4 Loose 0.5 2.5
61 IN 18.5 90.3

}
Poured in place 2 9.8
Wood studs 2”x4” (50xl00mm) Rigid 1.5 7.3
12-16 In.(300-400mm/o.C.) 2 9.8 Walls
Steel partitions 4 19.5 Kirby-wall 26g 1 4.8
Plaster 1 in. (25mm) Kirby-wall 24g 1.2 5.9
Cement 10 48 Brick
Gypsum 5 24.4 4 In. (100mm) 40 195.3
Lathing 8 In . (200mm) 80 390.6
Metal 0.5 2.4 12 In .(300mm) 120 586.0
Gypsum board 1/2 in. (12mm) 2 9.8 Hollow concrete
Floors Block ( heavy Aggregate)
Kirby deck-26g 1.1 5.5 4 In . (100mm) 30 146.5
Concrete re·inforced 1 in. (25mm) 6 In. (150mm) 43 210.0
Stone 12.5 61.0 8 In. (200mm) 55 268.6
Slag 11 .5 56.2 12.5 In. (318mm) 80 390.6
Lightweight 6-10 29.3-48.8 Hollow concrete
Block (light aggregate)
Concrete plain 1 in. (25mm)
Concrete plain 1 in. (25mm)
Stone 12 58.6
4 IN. (100mm) 21 102.6
Slag 11 53.7
6 IN. (150mm) 30 146.5
Lightweight 3-9 14.7-43.9 8 IN. (200mm) 38 185.6
Fills 1 in. (25mm) 12 IN. (300mm) 55 268.6
Gypsum 6 29.3 CLAY TILE (LOAD BEARIN)
Sand 8 39.1 4 IN . (100mm) 25 122.1
Cinders 4 19.5 61N. (150mm) 30 146.5
Finishes 8 IN. (200mm) 33 161.2
Terrazzo 1 in. (25mm) 13 63.5 12 IN. (300mm) 45 219.7
Ceramic tile 3/4 in. (19mm) 10 48.8 STONE 4 IN. (100mm) 55 268.6
Linoleum 1/4 in. (6mm) 1 4.9 Glass block 4 in. (100mm) 18 87.9
Mastic 3/4 in. (19mm) 9 43.9 Windows, glass, frame & Sash 8 39.1
Hardwood 7/8 in. (22mm) 4 19.5 Struct. Glass 1 in. (25mm) 15 73.3

94
Softwood 3/4 in. (19mm) 2.5 12.2
}
Corrugated cement
Asbestos 1/4 in. (6mm) 3 14.7
5.38 CONVERSION
FACTORS
MEASURE TO CONVERT MULTIPLY BY

From TO
Length Inch mm 25.40
Foot meter 0.3048
Micron meter 1.0 X 10-6
Mil meter 2.540 X 10-5
Area Mile meter 1609.30
Yard meter 0.9144
Inch2 mm2 645.16
Foot2 meter2 0.0929
Volume Acres kilometer2 4.04687 X 10-3
Inch 3
meter3 1.638706 X 10-5
Foot meter3
3
2.831685 X 10-2
Gallon (U .S.) Meter3 3.785412 X 10-3
Mass Gallon (U .S.) Liters 3.78543
Gallon (British Imperial) gallon (U.S.) 1.20091
Meter3 liters 1000.0
Pounds kilograms 0.45359
Velocity Metric Ton pounds 2204.62
Metric Ton long ton 0.98421
Metric Ton short ton 1.10231
Foot/hour mile/hour 0.000190
Pressure Mile/hour (U . S . ) Kilometer/hour 1.609344
Or Feet/minute meter/second 0.00508
Stress Miles/hour meter/second 0.44704
Pound force/foot newton/meter2 47.88026
Kg/cm2 newton/meter2 9.806650 X 104
Kn/m 2
pounds/Foot2 (psf) 20.885
Density Kn/cm 2
kips/in2 (ksi) 1.4504
Kg/mm2 newton/mm2 (pascal) 9.8066
Pounds/ft3 kg/m3 16.0185
Pounds/inch3 grams/cm3 27.680
Temperature °F °C (°F-32)/1.8
°C °F (°C x 1.8) + 32
BTU/FT2 KCal/m2 2.71
Heat BTU/FT HR F º
KCal/m2 Hr °C 4.88
BTU/FPHR F º
WATT/m2°C 5.674466

95
5.39 AIRCRAFT DIMENSION

Aircraft type L (m) W(m) H (m)

TUPOLEV
TU-154 154B-2 54.10 44.84 16.50
154M 54.10 44.84 16.50

Aircraft type L (m) W(m) H (m)

EMBRAER
170 29.90 26.00 9.85
175 31.68 26.00 9.73
190 36.24 28.72 10.57
195 38.65 28.72 10.55

96
 Aircraft type L (m) W(m) H (m) Aircraft type L (m) W(m)
BOEING AIRBUS
020 41.25 39.90 12.65 600 54.10 44.84 16.50
B707 120B 44.07 39.90 12.93
A300 600F 54.10 44.84 16.50
320B 46.61 44.42 12.93
B717 200 37.80 28.47 8.92 600ST 56.75 44.84 17.24
100 40.60 32.90 10.30 A310 - 46.66 43.90 15.80
B727 200 46.70 32.90 10.30 A319 33.84 34.10 11.76
200F 46.70 32.90 10.30 A320 A320 37.57 34.10 11.00
100 28.65 28.35 11.23
A321 44.51 34.10 11.76
200 30.53 28.35 11.23
300 33.40 28.90 11.10 200 58.82 60.30 17.39
B737 400 36.40 28.90 11.10 A330 200F 58.82 60.30 16.88
500 31.00 28.90 11.10 300 63.69 60.30 16.83
600/700 31.20 34.30 12.60 300 63.69 60.30 16.91
800/900 42.10 35.80 12.60
200 59.40 60.30 16.80
100B 70.60 59.60 19.30 A340
200B 70.60 59.60 19.30 500 67.93 63.45 17.28
B747 300 70.60 59.60 19.30 600 75.36 63.45 17.22
400/400ER 70.60 64.40 19.40 800 60.54 64.75 17.10
8I 76.25 68.50 19.40 A350 900 66.89 64.75 17.10
200 47.32 38.05 13.56
1000 73.88 64.75 17.90
B757 200F 47.32 38.05 13.56
300 54.47 38.05 13.56 A380 800 72.72 79.75 24.09
200 48.50 47.60 15.80
200ER 48.50 47.60 15.80
B767
300 48.50 47.60 15.80 Aircraft type L (m) W(m) H (m)
300ER 48.50 47.60 15.80
COMAC
300F 54.90 47.60 16.00
C919 - 38.90 35.80 11.95
400ER 61.40 51.90 16.80
700 33.50 27.30 8.40
200 63.70 60.90 18.50
700ER 33.50 27.30 8.40
200ER 63.70 60.90 18.50 ARJ21
900 36.40 27.30 8.40
200LR 63.70 64.80 18.60
B777 900ER 36.40 27.30 8.40
Freighter 63.70 64.80 18.60
300 73.90 60.90 18.50
300ER 73.90 64.80 18.50 Aircraft type L (m) W(m) H (m)
8 57.00 60.00 17.00
B787 CANADIAN REGIONAL JET
9 63.00 60.00 17.00
Bombardier crj-1000
39.10 26.20 7.10
Aircraft type L (m) W(m) H (m)
ANTONOV
100A 29.10 28.90 87.30
AN-148 100B 29.10 28.90 87.30
100E 29.10 28.90 87.30

Aircraft type L (m) W(m) H (m)

SUKHOI
SSJ 95 29.80 27.80 10.30
Superjet 100
SSJ 95LR 29.80 27.80 10.30

97
6 : ACCESSORIES
6.1 WALK DOORS

Specifications:

Doors are fabricated from electro-galvanised Standard sizes are 914 mm wide x 2134 mm high
steel (20 gauge), with a solid core of rigid (ref 3070 M or G) single swing doors and 1830
polyurethane insulation: Doors are provided mm wide x 2134 mm high (ref 6070 M or G)
either all metal (ref ‘M’), or with opening for glass double swing doors. All universal swing type. All
(ref ‘G’). Glass and glazing are not supplied by doors shop painted one coat vinyl based. neutral
Kirby. grey primer.

Each single door is supplied complete with one Availability:

cylindrical lock, double doors have a cylindrical
handle also. Panic hardware is available on special order as
are removable mullions for 6070 doors where
both leaves are active.

For standard details refer Installation Drawings.

98
6.2A SLIDING DOORS

Specifications:
1. D oors are located in increments of 167mm
All structural components are from cold formed The maximum dimension a single slide door
steel sections. with panels on the outerface, can extend beyond the jamb is the door
to match with the building walls. Doors will be width + 167mm.
provided with liner if the building has also K.R. 2. The maximum dimension a double slide door
liners. can extend beyond the jamb is half the door
width+167mm.
Doors are suspended by top track system within
3. No doors or windows may be located within
a header assembly and fitted with guides only at
operating limits of slide doors.
the base.
4. Doors are not operable beyond the corner of
Single sliding door height available 3000(M), the building, nor within 500mm of the corner
3500(M), 4000(M), 4500(M), 5000(M), of a side wall with down spouts.
5500(M) Door width available 3000(M), 5. A maximum of one door may be located in each bay.
4000(M), 5000(M), 6. Jamb to header member connections must
be field drilled, girt and base angles must be
Double sliding door height availability 3000(M), field cut.
3500(M), 4000(M), 4500(M), 5000(M), 7. Slide direction for single slide doors must
5500(M) 6000(M) double width available always be specified.
3000(M), 4000(M), 5000(M), 6000(M) 8. For single slide door details refer Installation
Dwg. 7.10
Availability: 9. For double slide door details refer Installation
Dwg. 7.10
10. For slide door details in masonry walls refer
The following parameters should be followed: Installation Dwg. 7.10

99
6.2B SLIDING FOLDING
DOOR

Description:

Kirby Sliding Folding Doors (KSFD) consist of without additional structural framing
1040 mm leaves suspended and connected in and additional cost.
a manner in order to move by folding against ƒƒ Track header is concealed without additional
each other and designed to have maximum clear flashing.
opening with minimum occupied space. ƒƒ Aluminium and neoprene strip are provided
for tight closure to prevent the penetration
Door leaf is covered with KR, KW, KCS or KC of light and dust from outside
panels with standard colors. The width of the ƒƒ Bottom guide can be set after the door is
opening is minimum 3.5 m and maximum 16 m; erected to provide a better alignment
in excess of 16 m width, floating door units are ƒƒ Variety of profile colors is available for door
used. sheeting.
ƒƒ Easy to relocate and reinstall with minimum
Features: foundation cost

ƒƒ K SFD provides a large clear opening with

easy movement
ƒƒ Doors are supported on top guide roller
assembly
ƒƒ Leaf frames are manufactured and shipped Kirby Building Systems reserves the right to
with “ready to erect” condition make changes without prior notice
ƒƒ Track headers are manufactured from built- KBS-KSFD-120911-00
up members that are very easy to install

100
Material Specification:

Specific Yield stress of steel, Fy = 34.5 kN/cm2 (ASTM A792 grade 50)
Door leaf frame 100 mm x 50 mm channel (pre-galvanized) with thicknesses 1.75,
2.0 and 2.5 mm
Top guide LG-305 Kirby standard door guide
Door Guide Brackets 3A-305 and 3A-305C Kirby standard support brackets
Hangar Trolley Kirby standard hanger trolley designed to turn 360º
Bottom roller Kirby standard 104P /97
Bottom guide Kirby standard channel guide 97P /3000 with channel lugs and
universal coupler
Hinges Heavy duty hinge
Panels KC panels (333 coverage), KR, KWand KCS panels (1000 mm
coverage)
Top stud roller Top stud roller assembly with bronze bush

Plan showing door @ closed condition

Detail of door leaf with top guide Detail of door leaf with bottom guide
Kirby building systems reserves the right to make
changes without prior notice Kbs-ksfd-120911-00

101
6.3 ROLL-UP DOORS -
MANUALLY OPERATED

PLAN

VIEW ‘X-X’

Door height (m) A (mm) B (mm) C (mm) D (mm)

3.0 50 610 580 640
3.5 40 620 580 640
4.0 30 630 580 640
4.5 20 670 600 690
5.0 - 690 600 690

Standard door sizes

DOOR WIDTH (M) DOOR HEIGHT (M)
3.0, 4.0 3.0,3.5, 4.0, 4.5, 5.0
5.0 3.0, 3.5, 4.0

102
6.3 ROLL-UP DOORS -
ELECTRICALLY OPERATED

Door height (m) A (mm) B (mm) C (mm) D (mm)

3.0 380 650 590 660
3.5 350 660 590 660
4.0 340 670 590 660
4.5 485 680 680 690
5.0 465 680 680 690
5.5 455 710 700 730
6.0 445 730 700 730

Standard door sizes

Door width (m) Door height (m) Motor
3.0, 4.0 3.0,3.5, 4.0, 1 H.P.
4.0 4.5,5.0, 5.5, 6.0 2 H.P
5.0, 6.0 3.0,3.5, 4.0, 4.5, 5.0,6.0 2 H.P

POWER SUPPLY: NOTE:

1 H.P. -{220/380 V.
3Ø-50/60 Hz.
2 H.P. -{220/460 V. Operating voltage to be furnished, while
3Ø-50/60 Hz. ordering the electrically operated roll-up door.

103
6.3 ROLL-UP DOORS -
CLEARANCES
A. Doors in a sidewall:

B. Doors in a light (bearing) endwall:

C. Doors in a main frame endwall:

ƒƒ Dimensions are determined per job to ensure

that drive system and fittings clear main
frame.
104
6.4 INSULATION

Physical Properties:

Type - KIB / 12
Density - 12 Kg / M3

Thermal properties
Mean temp. K U (Btu / Ft2 Hr of)
Deg. F. Btu In/Ft2 Hr of 50mm 75mm 100mm 150mm
50 0.27 0.137 0.091 0.069 0.046
100 0.29 0.147 0.098 0.074 0.049
125 0.34 0.173 0.115 0.986 0.058
150 0.39 0.198 0.132 0.099 0.066

Conversion factors:

1 Btu ft2 hr of = 4.88 K cal / m2 Hrºc

= 5.67 W / m2 °c

105
6.5 ROOF CURB

Specifications: Design:
Curbs shall be a one-piece construction The top of the curb provides a level surface at the 1:
manufactured from a self-extinguishing glass fiber 10 roof slope.
reinforced polyester, 3mm thick, with 15 mil polyester
gel coated weathering surface on exterior. Unit shall The upper end of the monolithic panel of the curbs
be white in colour and opaque to light. Base shall is reduced in thickness to 2 mm to provide nesting
have the same configuration as the Kirby Rib profile. under the above splice panel. The upper end splice
portion may be cut off to install the unit as a patch on
Availability: an existing roof.

The roof curbs are designed for installation on Kirby

rib profile. Care should be taken in using either
type unit in areas where the temperature exceeds
93 degrees C. as the strength of the unit will be
reduced.

CURBED OPENING DIMENSIONS

Curb Size Curb height Adapter Panel Weight (Kg)
Dimensions
Front(min) Back(min) Width Length
1200 x 1200 360 mm 240 mm 1667 mm 1700 mm 21.00 max.
900 x 900 330 mm 240 mm 1334 mm 1700 mm 17.00 max.
600 x 600 300 mm 240 mm 1000 mm 1700 mm 13.50 max.

106
6.6 ROOF JACK

Specifications: Design:

Roof Jacks shall be a one-piece construction manufac-

tured from.a self-extinguishing glass fiber reinforced The upper end of the monolithic adapter panel of
polyester, 3 mm thick, with 15 mil polyester gel coated the curbs is reduced in thickness to 2 mm to provide
weathering surface on exterior. Unit shall be white in nesting under the above splice panel. The upper end
color and opaque to light. Base shall have the same splice portion may be cut off to install the unit as a
configuration as Kirby rib profile. patch on an existing roof.

Availability:

The Roof Jacks (all sizes) are designed for installation

on Kirby rib profiles. Care should be taken in using
either type unit in
areas where the temperature exceeds 93 degrees C
as the strength of the unit will be reduced.

Roof Jack Dimensions

Opening size Jack height Base dimensions Weight (Kg)
Width Length
50mm t0 100mm 265mm 334mm 500mm 2.25 MAX.
150mm to 300mm 290mm 667mm 700mm 4.00 MAX.

107
6.7 WINDOWS

Sliding windows
( Aluminum )

Specifications: Availability:

All structural members are from extruded Windows are self flashing if located at a standard
aluminium, with a minimum thickness of 1mm. location within K.W. panel. When using multiple
Windows are single slide; supplied preglazed units to form continuous
with clear glass and complete with half insect
screen. windows, jamb fins are butted together and pop
riveted.
Standard, nominal window size is 1m wide x 1 m
high. For standard location of windows refer to
standard building installation Dwg. No. C-18.

108
6.8 LOUVER

6.8A ADJUSTABLE LOUVER

Specifications: Availability:

Louver frames are fabricated from 1.2 mm Single unit is self supporting and self flashing
thick (18 gauge) galvanized steel with 0.9 thick when used with K.W.panel only. When using
(20 gauge) galvanized steel blades. Blades are multiple units, with K.W. panel, to form
adjusted by use of a hand crank. All louvers are continuous louvers supporting jambs are
complete with bird screens. Finished color of provided.
louvers is white.
For use with K.R., supporting jambs are provided
for both single and continuous louvers. For
standard location of louvers refer to Installation
Details.

109
6.8 B. SAND TRAP LOUVER

Sand trap louver - data sheet

Description:
The specific yield stress for steel = fy = 34.5
The sand trap louver is recognized by Kirby’s
kN/cm2 as per ASTM A792 Grade 50.
standard designation as: STL1-1000 or STL1-2000
since it can be produced with a 1 m or 2 m
Height. Engineering and performance data:
U - shaped profiles are placed alternatively in a
vertical configuration allowing sand and heavy
dust separation. These vertically arranged Effective area factor.
sections and the opening at the bottom ensure
that the sand trap louver is self-cleaning and Air flow rate
maintenance free.
The sizes of the STL1-1000 or STL1-2000 are 1.0 Vf -→ face velocity (m/s)
M height x 1.0M width and 2.0 M height x 1.0M L → sand trap louver length (mm)
width, respectively. The STL is available in 24 H → sand trap louver height (mm)
Ga (0.6 mm) steel only.

Air flow rate values in I/s For STL1-1000 or STL1-2000

H 1000 2000
L
Vf = 1.0 Vf = 1.5 Vf = 1.0 Vf = 1.5
1000 254 382 554 832

Filtration Efficiency :
For normal operation conditions, Sand Trap Louvers
The filtration performance is dependant on the dust used for natural ventilation purpose are rated at a rec-
type and the velocity of the air. ommended Face Velocity not exceeding 1.0 - 1.5 m/s.

Partical size range Approx. Filtration efficiency in (%)

@ 1.0 m/s @ 1.5 m/s
350-700 80 75
75-700 55 35

110
6.9 TRANSLUCENT PANELS

Skylights and wall lights: Translucent panels:

Made of translucent GRP to match Kirby roof and wall Skylights and wall lights are translucent corrugated
panels, with an estimated light transmitting capacity sheets matching the profile of kirby-rib and kirby-wall
of 60%. sheets respectively. The translucent sheets are made
from glass fiber reinforced polyester structural plastic
panels and provide an economic form of general pur-
pose natural lighting.

111
6.9 TRANSLUCENT PANEL

Specifications: Mechanical Properties:

Thickness = 1.5 mm Tensile Strength = 8.7 kN/cm2 (ASTM D638)
Covering Width = 1 m Compressive Strength = 16.2 kN/cm2 (ASTM D695)
Standard Length = 3.305 m Flexural Strength = 13.83 kN/cm2 (ASTM D790)
Light Transmission = 60% (ASTM D1494) Flexural Modulus = 728 kN/cm2 (ASTM D790)
Solar Transmission = 35% (ASTM E424) Shear Strength = 10.34 kN/cm2 (ASTM D732)
Infra-red Transmission = <10% (ASTM E424) Barcol Hardness = 40 to 60 (ASTM D2583)
Impact Strength = 470 J/m (ASTM D256)
Physical Properties:
Density = 1431.9 kg/m3 (ASTM D792) Thermal Properties:
Water Absorption = <0.25% (ASTM D570) Thermal Transmittance (U Value) = 5.7 W/m2.K
(ASTM C518)
Operating Temperature: Linear Thermal expansion Coefficient = 1.6 x 10 -6 / F
The parameter is -30 ºC to + 75 ºC (ASTM D 696)

Panel Structural Properties:

Pull out
Fastener Data Sheet Purlin Thickness (mm) 1.50 1.75 2.00 2.50
Ultimate Pull Out (kN) 1.16 1.83 2.09 2.32

Base Material Thickness Covering Weight Area Full Elastic

(mm) width (kg/m) (cm2) section modulus (E)
(mm) (Ix) (cm4) kN/cm2
Fibre Glass 1.50 1000 2.387 17.17 15.82 718

Allowable Uniform Loads kN/m2):

Thickness Span in Meters
(T) No. of Load
(mm) Spans Case 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.50

1.5 D+L 2.99 1.92 0.99 0.57 0.36 0.24 0.17 0.12
1 WP 2.99 1.92 0.99 0.57 0.36 0.24 0.17 0.12
WS 2.99 1.92 0.99 0.57 0.36 0.24 0.17 0.12
D+L 1.96 1.31 0.93 0.69 0.53 0.42 0.34 0.28
2 WP 1.96 1.31 0.93 0.69 0.53 0.42 0.34 0.28
WS 1.96 1.31 0.93 0.69 0.53 0.42 0.34 0.28
The Allowable loads for winds are without 33% NOTE:
increase
D+L - Dead + Live Load WP - Wind Pressure Skylights are not designed for walk-on. Building
Load WS - Wind Suction Load installation/ maintenance staff should avoid
Allowable Deflection = Span / 45 crawling boards walking on the skylights else
that span over the skylight must be used.
Kirby Building Systems reserves the right to
make changes without prior notice KBS-SKY-l10811-01

112
6.10 VENTILATORS

RIDGE VENTILATORS Availability:

Specifications: Continuous ventelators are formed by joining

end skirts together. Providing the building length
is divisible by 3 m, maximum length of ventilator
Ventilators are gravity type, fabricated from
is building length minus 333mm.
galvanized steel sheets, shop assembled with
pop rivets.
Powered Ventilators:
Minimum throat width is 300 mm, with each
complete length being 3m. Manually operated Kirby ‘C’ whirlwind low silhouette extract
mechanical control dampers are provided, one ventilator with spun aluminum non- return
set for each 6m length of continuous vent or one shutter and one
single vent. Bird screens are also provided. piece base and throat.

Mounted on GRP roof curb moulded to suit

Kirby rib roof panels.

113
6.11 GUTTERS, FLASHINGS
& TRIMS

114
6.12 GUTTERS &
DOWNSPOUTS

Span Downspout spacing

6,9 & 12M 24.00M.O.C.
15M 22.00M.O.C.
18M 19.00M.O.C.
501 Series

20M 17.50M.O.C.
21M 17.00M.O.C.
24M 15.00M.O.C.
30M 13.00M.O.C.
36M 11.00M.O.C.
42M 10.00M.O.C.
45M 9.50M.O.C.

48M 13.50M.O.C.
54M 12.50M.O.C.
502 Series

60M 11.50M.O.C.
72M 10.00M.O.C.
84M 8.50M.O.C.
96M 8.00M.O.C.

115
6.13 VALLEY GUTTER &
DOWNSPOUT

* To be calculated based on drained area and downspout Spacing as given in formulae on sheet #
5.34

116
6.14 KIRBY ‘ M ’ LINER

Specifications: Availability:

Kirby ‘M’ liner consists of sheet metal panel and Wall liners are supplied either full height or
flashing (26Ga.) attached to the girt from inside partial height. Partial height wall liners are
of the building by self tapping screws. Standard stopped at a standard girt locations. If the liners
panelling is Kirby rib profile, galvanised or color are stopped at non-standard girt locations an
coated (white only). additional line of girt is required to support the
liner.

At translucent panels, the liner panel shall be cut

and the ends are trimmed with flashing unless
double layer of translucent panels are ordered.

Slide doors shall be lined for building with wall

liner. All framed openings and cut edges shall be
furnished with flashings around the opening.

Wall liners are supported by base channel at

base (base channel is supplied plain without
holes.holes are to be field drilled to the exact
spacing of anchor bolts as cast on site), by girts
at the middle and by liner support flashing at
eave. Roof liners are supported by the purlins.

117
6.15 KIRBY ‘ M ’ PARTITION

Specifications:

Kirby ‘M’ partitions consist of steel frame work Standard transverse partitions are located
of columns and girts covered with galvanised 356mm minimum away from the center line of
color coated panel, either one side or both sides. main frame.Transverse partitions can also be
Standard partition panels are 26 Ga. Kirby rib in the center line of the main frame provided
profile color coated ( white only ). the flange width of the frame does not exceed
200mm.
Availability:
An angle section shall be provided at base and
rake to support sheeting for single side sheeted
Longitudinal partition columns are connected
partitions. A channel section shall be provided
at base to foundation slab and at top to the
for double side sheeted partition.Base channel
rafter, generally same bay spacing as main frame
is supplied plain for field drilling of holes to the
columns. Girts are flush framed into the column.
set-out anchor bolt dimensions.
When sheeted from both sides of the framework
it gives a neat appearance. Single side sheeted Standard partitions are not supplied with
partitions are sheeted on one side of the insulation. However, insulation can be provided if
framework. specified.

Accessories such 3070 and 6070 doors, slide

doors, roll-up doors etc. can be fitted to the
partition

118
6.16 LIGHT PARTITIONS

Light partitions are generally not supplied by Kriby, Gypsum board panelS-shall be 13mm thick
consisting of a core of gypsum reinforced with
Following are suggested specifications only as a
approximately 40 mm long glass fiber pieces on
guideline to specifiers:
both sides. The gypsum board shall be covered by
The partition system shall be a complete and 0.8mm glued vinyl wall paper. Meanwhile board
functional system suitable for interior partitions panels shall consist of 12mm chipboard covered
or wall liner with acoustical and fire resistant on both sides by white melamine (80 g/m) added
properties and supplied as a finished product to the chipboard under pressure and heat.
with no further treatment like painting, etc,
Covered gypsum boards are used in dry areas
required prior to occupation, The partition
like offices, shops, bedrooms, etc .. , melamine
system shall allow for change in layout with all
boards in semi dry areas like kitchen, toilets, etc.
components fully reusable, The partition system
and plain gypsum boards to which ceramic tiles
shall be supplied in modular width of 0,9m x
can be glued (by others) are used in wet areas
2,7,1 m height with boards finished with vinyl wall
like bathrooms, etc.
paper of light grey color. The partition system
shall comprise of gypsum board or melamine Insulation shall be 50mm glass wool in rolls of 0.9
board panels mounted on both sides of vertical x 10 m with a heat transmission value of 0.0387
Z shaped steel studs and held by aluminum Kca/m 2 Hr. C, and density of approx 14 kg/m3,
connection profiles which shall envelop the
Galvanized steel profiles shall be of commercial
board panels to conceal the vertical joints, The
quality with a thickness of 0.75mm and
aluminum profiles shall be fixed to vertical Z
galvanized on both sides.
steel studs from either side by self penetrating
screws. The vertical Z studs shall be spaced at Aluminum profiles shall be made of natural
cms C/C and held into their vertical position by anodized materials. Thickness of profile shall be
bottom horizontal steel rails and top aluminum 1.0/1 .2/2.25 mm depending on type of profile
ceiling profiles. The bottom steel rails shall be with an anodization thickness of 10 microns.
‘C’ shaped profiles fixed to floor by suitable Internal doors in partitions shall consist of 830 x
fasteners. Aluminum ‘C’ profiles shall be used 2040mm mahogany veneered channel door leaf
as upper rails and wall starters and fixed to the in aluminum frame fixed to partition by special
ceiling or wall by means of suitable fasteners. fittings . The door shall be furnished with a steel
Black vinyl profile shall be used to cover the door handle and cylinder lock.
screws in the aluminum connection profiles.
At corners, steel corner profiles shall be used Internal windows shall be 880 x 970 mm
instead of steel studs and supported by upper provided with aluminum profile window frames
and lower rail. and suitable for glazing (by others) with 4mm
glass which is secured with vinyl window profiles.

119
6.17 FALSE CEILING

False Ceilings are generally not supplied by parallel to one another at a module of 120 cm in
Kirby. which the cross T form the network which hold
the tile in position. The main runners shall be
Following are suggested specifications only as a held to the structural ceiling by galvanized wires
guideline to specifiers: at intervals of 120cm.
The suspended ceiling shall be a flexible modular Edge moulding shall be L-shaped profiles to be
system of visible structure type and easily used as edge trim around the perimeter of the
demountable. Suspended ceiling tiles shall be room . These shall be secured to the wall by
60 x 60cm either of mineral fiber for application suitable fasteners at a spacing of 50cm.
in dry areas or asbestos tiles for application
in wet areas. Mineral fiber tiles shall consist All galvanized steel for main runner, cross T and
of 15mm hard pressed mineral wool and glue. edge moulding shall be hot dipped galvanized to
The exposed surfaces shall be sprayed white. 20 micron Zinc. The steel thickness shall be 0.4
Asbestos ceiling tiles shall be of non-inflammable mm for cross T and main runner and 0.25mm for
asbestos cellulose cement manufactured by the edge moulding. The edge moulding shall be
using asbestos fiber, cellulose and cement. The covered on the two outer sides by epoxy primer
tiles shall be hard pressed with a plain surface whereas the main runner and cross T shall be
and a greyish color. The material composition coated on exposed side only. Edge moulding
shall provide fire resistant properties, strength shall be finished on one side by 20 micron
and flexibility. polyester coating with 20% light reflection
according to girder 60 degree.
Main runners shall be T-shaped profiles running

120
7 : INSTALLATION DETAILS
7.1 ENDWALL DETAILS -
MAIN END FRAME

121
7.1 ENDWALL DETAILS -
MAIN END FRAME

NOTE :

1. Details shown on this drawing may not occur all 2. All high strength bolts shall have one H.S.
together in one building. Use those details which Washers and one H.S. Nut and shall be installed
comply with the structural framing, refer building in accordance with astm a 325 bolt specifications.
installation drawing.

122
7.1 ENDWALL DETAILS - “C”
BEARING FRAME

123
 NOTE:
NOTE:
Rake angle at top & bottom of purlin for
buildings with insulation up to roof slope 1. Details shown on this drawing may not occur
1.25:10. Rake angle at top of purlin only all together in one building. Use those details
for roof slopes 1.3:10 And above (with or which comply with the structural framing,
without insulation). refer building installation drawing.
Building installation marks shown on this 2. All high strength bolts shall have one H.S.
drawing is for building with roof slope 1:10. Washer and one H.S. Nut and shall be
See table below for corresponding building installed in accordance with astm a 325 bolt
installation marks for roof slopes other than specifications.
1:10.
Building installation Corresponding building installation mark for Remarks
Mark for slope 1:10 Slope 0.5:10 Slope 3:10 others
1-114 1-115” 1-114 See Building installation Dwg. ‘ For Flush Frame Slog. “
1-114” For By-Frame Slog.
1-83 1-85 1-84 See Building installation Dwg.
1-3 1-10 1-8 See Building installation Dwg.
1-13 1-13 1-13 1-13
1-1 1-5 1-6 See Building installation Dwg.
3-1250 Ur 3-1250Ur 3-1250Ur 3-1250Ur

124
7.1 ENDWALL DETAILS- “I”
BEARING FRAME (ALT,L)

125
7.1 ENDWALL DETAILS- “I”
BEARING FRAME (ALT,L)

NOTE :

1. Details shown on this drawing may not occur

all together in one building use. Those details
which comply with the structural framing,
refer to building installation drawings.
2. All high strength bolts shall have one H.S.
Washers and one H.S. Nut and shall be
installed in accordance with astm a 325 bolt
specifications.

126
7.1 ENDWALL DETAILS- “I”
BEARING FRAME (ALT,2)

127
 NOTE:

1. Details shown on this drawing may not occur

all together in one building use. Those details
which comply with the structural framing,
refer to building installation drawings.
2. All high strength bolts shall have one H.S.
Washer and one H.S. Nut and shall be
installed in accordance with astm a 325 bolt
specifications.
3. Part marks given are for 1:10 roof slope only.
Refer to building installation drawings if roof
slope is other than 1:10.

128
7.1 ENDWALL DETAILS-
GABLE

129
NOTE:

1. Details shown on this drawing may not occur 2. All high strength bolts shall have one H.S.
all together in one building use. Those details Washer and one H.S. Nut and shall be
which comply with the structural framing, installed in accordance with astm a 325 bolt
refer to building installation drawings. specifications.

130
7.2 PURLINS, GIRTS & EAVE
STRUT CONNECTIONS

131
132
7.2 GIRT CONNECTIONS

133
134
7.3 BRACING DETAILS

BRACE ROD FIXING DETAILS

135
NOTE :
of diaphragm strength of the fully sheeted
1. Details shown on this drawing may not occur wall.
all together in one building, use those details 4. When a sidewall of "s.V. Building" or light
which comply with the structural framing endwall (all buildings) is opened to a height
drawings furnished with the building greater than 2.2M rod bracing must be
2. Brace rods are indicated thus: 2r-6940 on installed.
building installation drawings, meaning 160 5. Bracings should never be dismantled for
rod 6940mm long. whatsoever the reasons may be. Connection
3. ( 1R=120, 3r=200, 4r=220 , 5r=240) bracing are bolts & nuts to be tight
not used in light endwalls or "s.V. Buildings" 6. And brace rods to be inspected periodically
in fully sheeted condition as the lateral wind for anyslackness.
force is carried to the foundation by means

136
7.4 EXPANSION JOINT
DETAILS

137
138
7.5 CANOPY & LEAN-TO
CONNECTIONS TO MAIN
BUILDING

139
7.5 EAVE CANOPY & PURLIN
EXTENSION DETAILS

140
NOTE :

1. All canopy eave purlins as well as eave purlin

laps are same as the required purlins in the
main building.
2. Rake channel is made of un punched material
(206x76cx1 .8)
3. All dimensions are in millimeters.
4. Part marks shown on this drawing are for roof
slope 1:10 only.Refer to building installation
drawings if roof slope is other than 1:10.

141
7.5 OVERHANG CANOPY
DETAILS

142
7.6 VERTICAL FASCIA
DETAILS

143
NOTE :

SCREWS 333 O.C. At each support for k.R. Panel stitch

(one@each support and (one) between per side
333 O.C. At each girt for k.W. Panel stitch (2 lap.
nos.) Between girt per side lap, 500 o.C. For mf
501a both sides.

144
7.6 FLUSHWALL FASCIA
DETAILS

145
7.7 VERTICAL MANSARD
DETAILS

146
147
7.7 CONVENTIONAL
MANSARD DETAILS
TYPE- III:

TYPE-V:

148
TYPE- IV:

TYPE-V:

149
7.8 ROOF FRAMED
OPENING DETAILS

150
151
7.9 WALK DOOR DETAILS

3’x7’ WALK DOOR 6’x7’ WALK DOOR

(914X2134) (1830X2134)

152
 6’x7’ door accessory package:
One no. Lockset consisting of:
2-Circular handles, 1-single point latch, 1-strike
and 8-fixing screws.
6 Nos. Hinges with 108-fixing screws. One no.
Foot bolt set consisting of: 1-6" foot bolt, 1-base
strike,1-bolt housing,1-surface strike,1-sprjng,
1-Chajn, 1-chain clip and
10-Screws. One no. Threshold.
2 Nos. Aluminium strips.
2 Nos. Vinyl strips.
14 Nos. Screws.
8 Nos. No.10Tampins.
4 Nos. M10x20/25 m.S. Bolts with nuts.
25 Nos. No.12X20 SDTS

3’x7’ door accessory package:

One no. Lockset consisting of:
2-Circular handles, 1-single point latch,
1-Strike and 8-fixing screws.
3 Nos. Hinges with 54-fixing screws.
One no. Threshold.
One no. Aluminium strips.
NOTE : One no. Vinyl strips.
8 Nos. Screws.
4Nos. No.10Tampins.
1. Glass & glazing for doors 6’x7’ g and 3’x7’g not 4 Nos. M10x20125 M.S. Bolts with nuts.
by kirby. 25 Nos. No.12X20 SDTS
2. A stragal installed on right hand inactive Door
leaf as a standard for 6’x7’ doors . Installation
on left hand on request .

153
7.10 SINGLE SLIDE DOOR
DETAILS

154
 Door stile schedule
DOOR HEIGHT LEFT HAND STYLE RIGHTHAND SffiE CENTER STYLES
30 0 0 10 x-110 L 1 0x-1 1 0 R 1 0x-2 1 5 L & R
3 50 0 10 x-112 L 1 0x-1 1 2 R 1 0x-2 1 6 L & R
40 0 0 10 x-114 L 1 0x-1 1 4 R 1 0x-2 1 7L & R
4 50 0 10 x-116 L 1 0x-1 1 6 R 1 0x-2 1 8 L & R
50 0 0 10 x-118 L 1 0x-1 1 8 R 1 0x-2 1 9 L & R
5 50 0 10 x-12 0 L 1 0x-1 2 0 R 1 0x-2 2 2 L & R

Door jamb schedule

DOOR HEIGHT DOORJAMB
3000 6-3x0
3500 6-3x5
4000 6-4x0
4500 6-4x5
5000 6-5x0
5500 6-5x5

Door track & bracket schedule

DOOR TRACK (LG-305) BRACKET
DOOR WIDTH LENGTH QTY. 3A-305C 3A-305
3000 6000 ONE 2 6
4000 6000+2000 ONE EACH 2 11
5000 6000+4000 ONE EACH 2 12

155
7.10 SINGLE SLIDE DOOR
DETAILS

156
NOTE:

1. Check the level of trackheader assembly and 2. Door handle w/dpm-1 to be fixed inside or
make sure that it matches clear opening of outside of building on any steel member of
door before building installation of door leaf. door leaf.

157
7.10 DOUBLE SLIDING
DOOR DETAILS.

158
159
7.11 SLIDING FOLDING DOOR
DETAILS

NOTE :

Door to be assembled on a level surface all

corners to be 90' after completion door leaves to
be sheeted in position

160
Position all doors (leaf) accurately lined & then second stage of conc. Tobe Done (to have botiom guide
in lined after alignment)

161
162
163
7.12 ROLL-UP DOOR
DETAILS

Part list:

1-2 Left & Right Brackest 10 Bottom Bar Angle

3-4 Right & Left Door Guide 11 WEATHER STRIP
5 Guide Brackets 12 HEAD STOP
6 Double Saddle 13 ALUM. STRIP
I Door curta1n 16-20 Axle- Spring BKT.
8-9 Locking Assembly 21 CUSHION HEAD STOP
9A-9B Outside & Inside Locking Bar 22 KEEPER PLATE
23 JAMB

164
165
7.12 ROLL-UP DOOR
DETAILS
Step-1 bracket fixing:

1. Fix left & right bracketto the clip 1-500l &

1-500r respectively
2. General tolerance for rud. Framing dimension
shall not exceed+/- 2 mm for vertical &
horizontal level.
3. Check all dimension and make sure that the
dimension are within tolerance limits before
assembling door.

Step-2 position door on bracket:

With the door correct way round (the curtain

rolls down rear of the opening) carefully lift
door onto the brackets, using block and tackles
attached to the door axles, or other suitable
lifting equipments.
A. Do not cut the band that holds the door in a
roll.
B. Rest axle between two cast iron saddles and
loosely secure to bracket arms with keeper
plate, bolts, nuts and washer provided. See
sketch b below. If chain gear is fitted, ensure
that the chain is placed around the chain
wheel and hangs down freely. As shown in
view x1

Before tightening saddle bolts, position the door

1. So that it overlaps the opening evenly both
side.
2. So that the axle is positioned on the bracket
arm slots as far forward
Possible, while still allowing the bottom rail to
pass the lintel or header when the door roll is
rotated. See sketch a. 3) Rotate both the door
and the axle so that bottom rail is level with
bracket arm . See sketch a.

166
Fixing or above the bracket arm
by dimension 'G' for restricted headroom
Door height dimension 'G'
upto4200mm 65mm
4200mm to 5100 mm 45mm

Step 3 Install guide:

Guide must be the correct length, top of the

guide should be level with top of bracket arm for
door height. If guides need to be shortened cut
from the bottom of guide.

Position the guide true and plumb of each side of

the opening allowing 3-4 mm of working clearance
between the door and the inside of each guide,
mark, drill and fix both the guides with coach
screw and washer supplied.

Step 4 Spring tensioning and bottom

rail sto:

Check top of the guide-in to ensure that the

door does not make contact when rotated apply
tension to spring by rotating door approximately
two complete turn in a forward direction (see
arrow on sketch a) after ensuring axle is securely
clamped. The amount of tension required for
satisfactory operation may vary with individual
doors, depending on size. Hold the door firmly
cut the bands, feed the door down into guides
below the head stop. Fit bottom rail stop using
self locking nuts provided. Allow the door to rise
and to rest against head stop.
(See sketch b)
Operate door up and down a number of times to
check the operation.

167
7.13 HANGAR DOOR
DETAILS

NOTE :

1. Clear height & clear opening are customers'

option.
2. Dimensions 'a' & 'b' are determined by type
of doors, cladding etc.
3. For common usage customer is required
to specify the range of aircraft to be
considered.

168
1. Clear height & clear opening are
customers' requirement.
2. Dimensions 'a' & 'b' are detirmined by
type of doors, cladding etc.
3. For common usage customer is
required
To specify the range of aircraft to be
considered.

169
7.13 HANGAR DOOR
DETAILS

170
171
7.14 CRANE SYSTEM DETAILS

172
7.14 CRANE BEAM & RAIL
DETAILS

NOTE :

Crane beam support bracket is provided with

slotted holes for easy assembly of bracing and
diaphragm angles. Adjustment of rail centers are
to be carried out by hook bolts. Where welded
bar rails are used, the adjustment of rail centers
are carried out by cranebeam. After aligning, if
the bracing and diaphragm angles does not fit
properly, weld them at the column end to their
Respective clips. Scrapepaint at welding area.
Repaint all field welds.

173
7.14 CRANE BEAMS &
RAILS- EXPANSION JOINT
DETAILS

174
7.15 MEZZANINE DETAILS

175
176
 General notes:

1. Mezzanine floors and flat roofs are designed

for concrete slab of a maximum thickness of
100mm including the thickness of corrugated
'kirby' deck panel.
2. Concrete is not the responsibility of kirby
building systems and must be designed by a
qualified civil engineer.
3. Reinforcing steel or wire mesh shall be placed
in the concrete as required by the design and
Design data: in accordance with the concrete compressive
strength and recognized Building codes.
1. Large openings in the mezzanine slab which 4. Live load deflection of structural members
require the partial removal of steel joists are limited to L/240 unless otherwise
must be specified in size and location to required or specified.
'kirby' and will require steel framed openings. 5. The mezzanine deck panel is considered
Any loading, from staircase, for example, on to carry only the Weight of the concrete
the steel framed openings must be defined (100mm maximum thickness).
in magnitude and location. The supply of 6. The concrete slab should be designed to
staircase by 'kirby' is limited to only when top carry the full Live load and any additional
of concrete is at 3.5 And 4.0 M from bottom floor finishes.
of base plate.
2. Mezzanine i flat roof live load must be 7. Concentrated loads due to storage of materials
specified in addition to any loadings from and Placing of concrete should be avoided.
floor finishes, suspended ceiling, mechanical 8. Mezzanine deck panels must be fastened at
ducts, piping, etc. every Corrugation to mezzanine joist using
3. Top elevation of concrete or clearance under s.O.S. Fasteners.
steel Joists i beams must be specified. 9. Openings in the mezzanine slab between
4. Depth of mezzanine construction varies steel joists May be made without affecting
between 60 em And 100 em depending on the steel mezzanine Framing, provided
loading support column Spacing and other proper reinforcement around the Openings
design criteria. is considered in the design of the slab.
177
7.15 STAIRCASE DETAILS

178
7.16 WALL PANEL &
DOWNSPOUT DETAILS

SDS I SOTS TABLE

INSULATION PANEL TO PANEL TO
SIZE STRUCTURE PANEL
0 to 60 No. 14 x 25 No. 12 x 20
75 to 100 No. 14 x 50 No. 12 x 20
110 to 150 No. 14 x 76 No. 12 x 20

179
 Span
SPAN Down-
DOWN- Span Down-
SPOUT
spout
SPACING
spout
6,9&12m spacing
24.0 m O.C.
Spacing
6,9&12m 24.0 m O.C.
O.C. 48 m 13.5 m O.C.
15m 22.0 m
15m 22.0 m O.C.
O.C. 54m 12.5 m O.C.
18m 19.0 m
18m 19.0 m O.C.
O.C. 60 m 11.5m0.C.
20m 17.5 m
20m 17.5 m 72 m 10.0 m O.C.
24m 15.0 m O.C.
O.C.
24m 15.0 m 84m 8.5m0.C.
30m 13.0 m O.C.
O.C.
30m 13.0 m O.C. 96 m 8.0m0.C.
36m 11.0m0.C.
36m
42 m 11.0m0.C.
10.0 m O.C.
42 m
45 m 10.0 m O.C.
9.5mO.C.
45 m 9.5mO.C.

General notes

1. Panel module- there is a plus or minus

tolerance Bull t into K.W. Panel.
Measure and mark *1000 O.C. (Begining on
the Steel line for endwalland '167 from steel
Line for sidewall) along base angle to check
Any dimensional gain or loss during
installation.
*Dimensions are applicable for buildings
having 333 Increments. Refer building
installation drawings for others.
2. Foundation must be square, level and of
correct Out to out dimensions for the
required building.
3. Building must be tight and plumb before
Sheeting begins.
4. Installation of panels should always Be as
showm in section 'a-a'.
5. Building installation crew is to clean all wall
panels Before leaving job site.
180
7.16 WALL PANEL DETAILS
WITH EAVE TRIM

181
 General sheeting notes

1. The building is to be tight and plumb before

sheeting is to begin.
2. Sheeting is to begin at the leeward end of
building so that all Panel laps will be away
SDS I SOTS TABLE from prevailing wind.
INSULATION PANEL TO PANEL TO 3. Skylights receive same screw pattern as roof
SIZE STRUCTURE PANEL panels except Skylight to skylight stitch. Use
0 to 60 No. 14 x 25 No. 12 x 20 grommet screws at this Condition.
75 to 100 No. 14 x 50 No. 12 x 20 4. After building installation, fill all unused
110 to 150 No. 14 x 76 No. 12 x 20 screw holes in the roof with No. 17X20 self
tapping screws.
5. Building installation crew is to sweep roof
panels clear of all metal shavings.
6. All dimensions are in millimeters.
182
7.16 WALL PANEL DETAILS
WITH EAVE GUTTER

183
 General sheeting notes:

1. The building is to be tight and plumb before

sheeting is to begin.
2. Sheeting is to begin at the leeward end of
building so that all Panel laps will be away
from prevailing wind.
3. Skylights receive same screw pattern as roof
panels except Skylight to skylight stitch. Use
grommet screws at this Condition.
4. Building installation crew is to sweep roof
panels clear of all metal shavings.
5. All dimensions are in millimeters.
SDS I SOTS TABLE
INSULATION PANEL TO PANEL TO
SIZE STRUCTURE PANEL
0 to 60 No. 14 x 25 No. 12 x 20
75 to 100 No. 14 x 50 No. 12 x 20
110 to 150 No. 14 x 76 No. 12 x 20

184
7.16 ROOF PANEL DETAILS
WITH VALLEY GUTTER

185
 General sheeting notes:

1. The building is to be tight and plumb before

sheeting is to begin.
2. Sheeting is to begin at the leeward end of
building so that all Panel laps will be away
from prevailing wino.
3. Skylights receive same screw pattern as roof
panels except Skylight to skylight stitch. Use
SDS I SOTS TABLE grommet screws at this Condition.
INSULATION PANEL TO PANEL TO 4. Afitr building installation. Fill all unused screw
SIZE STRUCTURE PANEL holes in the roof with No. 17X20 self tapping
0 to 60 No. 14 x 25 No. 12 x 20 screws.
75 to 100 No. 14 x 50 No. 12 x 20 5. Building installation crew is to sweep roof
110 to 150 No. 14 x 76 No. 12 x 20 panels clear of all metal shavings.

186
7.16 PANEL & TRIMS
FOR EAVE & PUR LIN
EXTENSION CANOPIES

187
188
7.17 WALL LINER PANEL
DETAILS

• Panel to Structure use SDS

• Panel to Panel & Trims use STDS
189
 NOTE :

1. Details shown on this drawing may not Occur

all together in one building. Use those details
which comply with the Structural framing.
Refer to building installation Drawing.
2. Refer sheet no. For roof and wall liner
Combination.
3. All dimensions are in millimeters.

190
191
192
7.17 LINER PANEL DETAILS
FOR SLIDE DOORS

193
NOTE:

Keep girt connection bolt head direction facing

upward and use round head bolts at flashings.

194
7.18 INSULATION DETAILS

195
NOTE:

1. An additional rake angle (on 1:10 bldg. Only) 3. For building having insulation of 80 & 150 mm
andacorner Angle will be furnished by k.B.S. thick blanket Type, use# 14 x 50 sds to fasten
When customer specifies That building is to panel to structure and 12 X 20 sdts panel to
be insulated (see details) panel.
2. For building having insulation of 50 & 75 mm 4. Slide doors are to be insulated if waiuls have
thick blanket Type, use# 15x25 sds to fasten insulation
panel to structure and Panel to panel. 5. All dimensions are in millimeters.
6. Patching tape is provided for patching of torn
vinyl facing.

196
7.19 ‘KR’ FALSE CEILING
DETAILS

NOTE:

1. The building is to be tight and plumb

before Panel-support is erected; however,
it is preferred To be done after external
sheeting is completed.
2. Panel-supportto be checked for constant
level Througholt before panel fixing begins.
3. Alignment of cutouts and misc. Fixings;
(lighting, Ducts, etc.) Are the responsibility
of the building installers.
4. F.C. Panels shall be installed in the
sequence shown.
5. Protective measures are to be taken to
prevent Personnel damaging the panels.
6. Do not punch holes or make marks with
permanent Ink or paint on the visible face.
7. Building installation crew is to clear off all
metal shavings and No sharp edges to be
left projecting hazardously.

197
7.20 SINGLE SHEETED
PARTITION DETAILS

198
NOTE :

1. Details shown on this drawing may not occur

all together in One building. Use those details
which comply with the Structural framing,
refer building installation drawing.
2. Column and girt spacing for partition walls is
same as that Required end wall.
3. All column and girt connections (unless
noted) are same As standard girt
connections.
4. All dimensions are in millimeters.

199
7.20 DOUBLE SHEETED
PARTITION DETAILS

200
NOTE :

1. Details shown on this drawing may not occur

all together in One building. Use those details
which comply with the Structural framing,
refer building installation drawing.
2. Column and girt spacing for partition walls is
same as that Required end wall.
3. All column and girt connections (unless noted)
are same As standard girt connections.
4. All dimensions are in millimeters.

201
7.21 RIDGE VENTILATOR
(300MM THROAT W/DAMPER)

202
203
7.21 RIDGE VENTILATOR
(600MM THROAT W/O DAMPER)

204
205
7.22 ROOF CURB DETAILS

NOTE:

Roof curb shall be installed as roof is sheeted

and in the sequence shown.

Protective measures are to be taken to prevent

personnel damaging the roof curb. Do not walk
on the roof curb.

206
7.22 ROOF JACK DETAILS

NOTE:

Roof jack shall be installed as roof is sheeted

Field cut appropriate opening for roof jack in
Roof panel.

Protective measures are to be taken to prevent

Personnel damaging the roof jack.

207
7.23 WINDOW DETAILS

208
7.23 SANDTRAP LOUVERS
( FIXED TYPE).

S/N PIECEMARK SIZE OF LOUVER MATERIAL

1 STL1-1000 1000W X 1000H STEEL

2 STL1-2000 1000W X 2000H STEEL

3 STL2-1000 2000W X 1000H STEEL

4 STL1-1000 AL 1000W X 1000H ALUMINIUM

209
 NOTE:

1. Opening for windows are field cut unless

otherwise noted on building installation
drawings furnished with the building.
2. Details shown are for windows at standard
locations.
3. Windows are self flashing when rtted at
standard locations.
4. Double windows in way of liner panels should
have a sill girt also.

210
7.23 ADJUSTABLE LOUVER
DETAILS
Louver details:

211
7.24 ROOF SANDWICH
PANEL DETAILS

212
General sheeting notes

1. The building is to be tight and plumb before

sheeting is to begin.
2. Sheeting is to begin at the leeward end of
building so that all Panel laps will be away
from prevailing wind.
3. Fiberglass insulation for filling the gaps to be
fixed With adhesive tape to prevent it from
flying. (Tape not supplied by kirby.)
4. Building installation crew is to sweep roof
panels clear of all metal shavings.

213
7.25 SUSPENSION OF
LOADS FROM MAIN &
SECONDARY MEMBERS

NOTE :

1. Drawing details shows the proper methods of 2. The total load suspended from purlin & rafter
suspending Loads from purlins & rafters. shall not Exceed the value of collateral load
indicated on this Drawing. If in doubt, please
contact kirby's nearest Representative for
confirmation.

214
7.25 STANDARD BUILDINGS
ERECTION DRAWINGS
( CONTINUATION FROM
CHAPTER 3.3 )
Index for standard buildings:

Width Length Eave height Bay Project no. Page

(m) (m) (m) spacing
36.00 48.00 6.00 [email protected] M. BC-36660 212
36.00 48.00 8.50 [email protected] M. BC-36685 218
36.00 48.00 6.00 [email protected] M. BC-36860 224
36.00 48.00 8.50 [email protected] M. BC-36885 230
18.00 48.00 6.00 [email protected] M. RF-18660 236
18.00 48.00 8.50 [email protected] M. RF-18685 242
18.00 48.00 8.50 [email protected] M. RF-18885 248
21.00 48.00 6.00 [email protected] M. RF-21660 254
21.00 48.00 8.50 [email protected] M. RF-21685 260
21.00 48.00 6.00 [email protected] M. RF-21860 266
21.00 48.00 8.50 [email protected] M. RF-21885 272
36.00 48.00 6.00 [email protected] M. RF-36660 278
36.00 48.00 6.00 [email protected] M. RF-36685 284
36.00 48.00 6.00 [email protected] M. RF-36860 290
36.00 48.00 8.50 [email protected] M. RF-36885 296

215
STANDARD STRUCTURAL
SYSTEM
3.3 STANDARD BUILDINGS -
BC-36660

216
Main frame column reactions:

Sign convensions:
Positive hor.Reaction : to the right
Positive ver.Reaction : upward
Positive moment : counter clockwise

Mainframe- 2-8

Reaction For Combined Loads:

Description Horz Vert Momt Load

KN KN KN-m combination
INT. COL. 1 0.0 88.9 KN-M 1DL+1LL
INT. COL. 1 0.0 -30.9 0.0 1DL+1WLL
INT. COL. 1 0.0 -30.9 0.0 1DL+1WLR
INT. COL. 1 0.0 18.4 0.0 1DL+1SEI
LEFT COL. 13.2 37.9 0.0 1DL+1LL
LEFT COL. -10.3 -19.1 0.0 1DL+1WLL
LEFT COL. 2.7 -6.7 0.0 1DL+1WLR
LEFT COL. 0.1 7.6 0.0 1DL+1SEI
RIGT COL. -13.2 37.9 0.0 1DL+1LL
RIGT COL. -2.7 -6.7 0.0 1DL+1WLL
RIGT COL. 10.3 -19.1 0.0 1DL+1WLR
RIGT COL. -5.1 9.2 0.0 1DL+1SEI

217
218
219
220
SIDE WALL SHEETING ELEVATION @ GL A (AS DRAWN)
SIDE WALL SHEETING ELEVATION @ GL G (OPP HAND)
S.W.D @ GL-A ONLY
221
3.3 STANDARD BUILDINGS -
BC-36685

222
Main frame column reactions:

Sign convensions:
Positive hor.Reaction : to the right
Positive ver.Reaction : upward
Positive moment : counter clockwise

Mainframe- 2-8
Reaction For Combined Loads:

Description Horz Vert Momt Load

KN KN KN-M combination
INT. COL. 1 0.0 88.9 0.0 1DL+1LL
INT. COL. 1 0.0 -30.9 0.0 1DL+1WLL
INT. COL. 1 0.0 -30.9 0.0 1DL+1WLR
INT. COL. 1 0.0 18.4 0.0 1DL+1SEI
LEFT COL. 13.2 37.9 0.0 1DL+1LL
LEFT COL. -10.3 -19.1 0.0 1DL+1WLL
LEFT COL. 2.7 -6.7 0.0 1DL+1WLR
LEFT COL. 0.1 7.6 0.0 1DL+1SEI
RIGT COL. -13.2 37.9 0.0 1DL+1LL
RIGT COL. -2.7 -6.7 0.0 1DL+1WLL
RIGT COL. 10.3 -19.1 0.0 1DL+1WLR
RIGT COL. -5.1 9.2 0.0 1DL+1SEI

223
224
225
226
227
3.3 STANDARD BUILDINGS -
BC-36860

228
Mainframe- 2-8
Reaction For Combined Loads:

Description Horz Vert Momt Load

KN KN KN-M combination
INT. COL. 1 0.0 92.8 0.0 1DL+1LL
INT. COL. 1 0.0 -35.7 0.0 1DL+1WLL
INT. COL. 1 0.0 -35.7 0.0 1DL+1WLR
INT. COL. 1 0.0 19.5 0.0 1DL+1SEI
LEFT COL. 7.6 36.7 0.0 1DL+1LL
LEFT COL. -11.9 -21.6 0.0 1DL+1WLL
LEFT COL. 9.0 -5.7 0.0 1DL+1WLR
LEFT COL. -1.1 7.4 0.0 1DL+1SEI
RIGT COL. -7.6 36.7 0.0 1 DL+1LL
RIGT COL. -9.0 -5.7 0.0 1DL+1WLL
RIGT COL. 11.9 -21.6 0.0 1DL+1WLR
RIGT COL. -4.1 9.8 0.0 1DL+1SEI

229
230
231
232
3.3 STANDARD BUILDINGS
BC-36860

233
3.3 STANDARD BUILDINGS -
BC-36885

234
Mainframe- 2-6
Reaction For Combined Loads:

Description Horz Vert Momt Load

KN KN KN-M combination
INT. COL. 1 0.0 124.1 0.0 1DL+1LL
INT. COL. 1 0.0 -48.2 0.0 1DL+1WLL
INT. COL. 1 0.0 -48.2 0.0 1DL+1WLR
INT. COL. 1 0.0 25.8 0.0 1DL+1SEI
LEFT COL. 9.1 47.6 0.0 1DL+1LL
LEFT COL. -15.7 -29.7 0.0 1DL+1WLL
LEFT COL. 12.1 -8.4 0.0 1DL+1WLR
LEFT COL. -1 .6 8.9 0.0 1DL+1SEI
RIGT COL. -9.1 47.6 0.0 1DL+1LL
RIGT COL. -12.1 -8.4 0.0 1DL+1WLL
RIGT COL. 15.7 -29.7 0.0 1DL+1WLR
RIGT COL. -5.0 11.9 0.0 1DL+1SEI

Main frame column reactions:

Sign convensions:
Positive hor.Reaction : to the right
Positive ver.Reaction : upward
Positive moment : counter clockwise

235
236
237
238
239
3.3 STANDARD BUILDINGS -
RF-18660

240
Main frame column reactions:

Sign convensions :
Positive hor.Reaction : to the right
Positive ver.Reaction : upward
Positive moment : counter clockwise

Mainframe- 2-8
Reaction For Combined Loads:

Description Horz Vert Momt Load

KN KN KN-M combination
LEFT COL. 19.5 41.6 0.0 1DL+1LL
LEFT COL. -13.0 -18.7 0.0 1DL+1WLL
LEFT COL. 0.8 -8.9 0.0 1DL+1WLR
LEFT COL. 2.4 8.4 0.0 1DL+1SEI
RIGT COL. -19.5 41.6 0.0 1DL+1LL
RIGT COL. -0.8 -8.9 0.0 1DL+1WLL
RIGT COL. 13.0 -18.7 0.0 1DL+1WLR
RIGT COL. -5.0 10.0 0.0 1DL+1SEI

241
242
243
3.3 STANDARD BUILDINGS -
RF-1866

244
3.3 STANDARD BUILDINGS -
RF-18660

245
3.3 STANDARD BUILDINGS -
RF-18685

246
Main frame column reactions:

Sign convensions:
Positive hor.Reaction : to the right
Positive ver.Reaction : upward
Positive moment : counter clockwise

Mainframe- 2-8
Reaction For Combined Loads:

Description Horz Vert Momt Load

KN KN KN-M combination
LEFT COL. 13.2 42.3 0.0 1DL+1LL
LEFT COL. -13.2 -20.4 0.0 1DL+1WLL
LEFT COL. 6.8 -5.8 0.0 1DL+1WLR
LEFT COL. 1.1 8.6 0.0 1DL+1SEI
RIGT COL. -13.2 42.3 0.0 1DL+1LL
RIGT COL. -6.8 -5.8 0.0 1DL+1WLL
RIGT COL. 13.2 -20.4 0.0 1DL+1WLR
RIGT COL. -3.9 11.2 0.0 1DL+1SEI

247
248
249
250
251
252
Main frame column reactions:

Sign convensions:
Positive hor.Reaction : to the right
Positive ver.Reaction : upward
Positive moment : counter clockwise

Description Horz Vert Momt Load

KN KN KN-M combination
LEFT COL. 17.9 55.6 0.0 1DL+1LL
LEFT COL. -17.7 -28.0 0.0 1DL+1WLL
LEFT COL. 8.9 -8.6 0.0 1DL+1WLR
LEFT COL. 1.7 10.8 0.0 1 DL+1SEI
RIGT COL. -17.9 55.6 0.0 1DL+1LL
RIGT COL. -8.9 -8.6 0.0 1DL+1WLL
RIGT COL. 17.7 -28.0 0.0 1DL+1WLR
RIGT COL. -5.1 14.0 0.0 1DL+1SEI

253
254
255
256
257
3.3 STANDARD BUILDINGS -
RF-21660

258
Main frame column reactions:

Sign convensions:
Positive hor.Reaction : to the right
Positive ver.Reaction : upward
Positive moment : counter clockwise

Mainframe- 2-8
Reaction For Combined Loads:

Description Horz Vert Momt Load

KN KN KN-M combination
LEFT COL. 27.3 48.6 0.0 1DL+1LL
LEFT COL. -15.6 -21.0 0.0 1DL+1WLL
LEFT COL. -2.1 -11.1 0.0 1DL+1WLR
LEFT COL. 3.8 10.0 0.0 1DL+1SEI
RIGT COL. -27.3 48.6 0.0 1DL+1LL
RIGT COL. 2.1 -11.1 0.0 1DL+1WLL
RIGT COL. 15.6 -21.0 0.0 1DL+1WLR
RIGT COL. -6.8 11.6 0.0 1DL+1SEI

259
260
261
 ENDWALL SHEETING ELEVATION @ GRID 9
KW PANEL-0.5MM THK(ARCTIC WHITE)

262
263
3.3 STANDARD BUILDINGS -
RF-21685

264
Main frame column reactions:

Signconvensions:
Positive hor.Reaction : totheright
Positive ver.Reaction : upward
Positive moment : counter clockwise

Mainframe- 2-8
Reaction For Combined Loads:

Description Horz Vert Momt Load

KN KN KN-M combination
LEFT COL. 19.2 49.8 0.0 1DL+1LL
LEFT COL. -16.6 -24.6 0.0 1DL+1WLL
LEFT COL. 4.8 -9.5 0.0 1DL+1WLR
LEFT COL. 2.1 10.7 0.0 1DL+1SEI
RIGT COL. -19.2 49.8 0.0 1DL+1LL
RIGT COL. -4.8 -9.5 0.0 1DL+1WLL
RIGT COL. 16.6 -24.6 0.0 1DL+1WLR
RIGT COL. -5.5 13.3 0.0 1DL+1SEI

265
266
267
268
269
3.3 STANDARD BUILDINGS -
RF-21860

270
Main frame column reactions:

Sign convensions:
Positive hor.Reaction : to the right
Positive ver.Reaction : upward
Positive moment : counter clockwise

Mainframe- 2-6
Reaction For Combined Loads:

Description Horz Vert Momt Load

KN KN KN-M combination
LEFT COL. 36.3 64.2 0.0 1DL+1LL
LEFT COL. -21.1 -28.5 0.0 1DL+1WLL
LEFT COL. -3.0 -15.4 0.0 1DL+1WLR
LEFT COL. 5.0 12.8 0.0 1DL+1SEI
RIGT COL. -36.3 64.2 0.0 1DL+1LL
RIGT COL. 3.0 -15.4 0.0 1DL+1WLL
RIGT COL. 21.1 -28.5 0.0 1DL+1WLR
RIGT COL. - 8.8 14.8 0.0 1DL+1SEI

271
272
 SIDEWALL SHEETING ELEVATION @ GL A

273
274
275
3.3 STANDARD BUILDINGS -
RF-21885

276
Main frame column reactions:

Sign convensions:
Positivehor.Reaction : to the right
Positive ver.Reaction : upward
Positivemoment : counter clockwise

Mainframe- 2-6
Reaction For Combined Loads:

Description Horz Vert Momt Load

KN KN KN-M combination
LEFT COL. 25.1 64.2 0.0 1DL+1LL
LEFT COL. -22.2 -28.5 0.0 1DL+1WLL
LEFT COL. 6.3 -15.4 0.0 1DL+1WLR
LEFT COL. 6.3 12.8 0.0 1DL+1SEI
RIGT COL. -25.1 64.2 0.0 1DL+1LL
RIGT COL. -6.3 -15.4 0.0 1DL+1WLL
RIGT COL. 22.2 -28.5 0.0 1DL+1WLR
RIGT COL. 22.2 14.8 0.0 1DL+1SEI

277
278
 SIDEWALL SHEETING ELEVATION @ A

279
 ENDWALL SHEETING ELEVATION @ GRID 1

280
281
3.3 STANDARD BUILDINGS -
RF-36660

282
Main framecolumnreactions:

Sign convensions:
Positive hor.Reaction : to the right
Positivever.Reaction : upward
Positivemoment : counterclockwise

Mainframe- 2-8
Reaction For Combined Loads:

Description Horz Vert Momt Load

KN KN KN-M combination
LEFT COL. 86.6 86.9 0.0 1DL+1LL
LEFT COL. -32.5 -30.1 0.0 1DL+1WLL
LEFT COL. -19.8 -17.8 0.0 1DL+1WLR
LEFT COL. -16.5 21.2 0.0 1DL+1SEI
RIGT COL. -86.6 86.9 0.0 1DL+1LL
RIGT COL. 19.8 -17.8 0.0 1DL+1WLL
RIGT COL. 32.5 -30.1 0.0 1DL+1WLR
RIGT COL. -22.7 23.0 0.0 1DL+1SEI

283
284
285
286
287
3.3 STANDARD BUILDINGS -
RF-36685

288
Main frame column reactions:

Sign convensions:
Positive hor.Reaction : to the right
Positive ver.Reaction : upward
Positive moment : counter clockwise

Mainframe- 2-8
Reaction For Combined Loads:

Description Horz Vert Momt Load

KN KN KN-M combination
LEFT COL. 61.3 89.0 0.0 1DL+1LL
LEFT COL. -30.1 -33.5 0.0 1DL+1WLL
LEFT COL. -9.7 -17.8 0.0 1DL+1WLR
LEFT COL. 10.6 22.7 0.0 1DL+1SEI
RIGT COL. -61.3 89.0 0.0 1DL+1LL
RIGT COL. 9.7 -17.8 0.0 1DL+1WLL
RIGT COL. 30.1 -33.5 0.0 1DL+1WLR
RIGT COL. -17.4 25.7 0.0 1DL+1SEI

289
290
291
292
293
3.3 STANDARD BUILDINGS -
RF-36860

294
Main frame column reactions:

Sign convensions:
Positive hor.Reaction : to the right
Positive ver.Reaction : upward
Positive moment : counter clockwise

Mainframe- 2-6
Reaction For Combined Loads:

Description Horz Vert Momt Load

KN KN KN-M combination
LEFT COL. 113.7 114.9 0.0 1DL+1LL
LEFT COL. -43.9 -41.1 0.0 1DL+1WLL
LEFT COL. -27.0 -24.6 0.0 1DL+1WLR
LEFT COL. 21.1 27.3 0.0 1DL+1SEI
RIGT COL. -113.7 114.9 0.0 1DL+1LL
RIGT COL. 27.0 -24.6 0.0 1DL+1WLL
RIGT COL. 43.9 -41.1 0.0 1DL+1WLR
RIGT COL -29.1 29.7 0.0 1DL+1SEI

295
296
297
298
299
3.3 STANDARD BUILDINGS -
RF-36885

300
Main frame column reactions:
Sign convensions:
Positive hor.Reaction : to the right
Positive ver.Reaction : upward
Positive moment : counterclockwise

MAINFRAME - 2-8
REACTION FOR COMBINED LOADS:

Description Horz Vert Momt Load

KN KN KN-M combination
LEFT COL. 79.5 117.7 0.0 1DL+1LL
LEFT COL. -40.0 -45.7 0.0 1DL+1WLL
LEFT COL. -12.7 -24.6 0.0 1DL+1WLR
LEFT COL. 13.5 29.4 0.0 1DL+1SEI
RIGT COL. -79.5 117.7 0.0 1DL+1LL
RIGT COL. 12.7 -24.6 0.0 1DL+1WLL
RIGT COL. 40.0 -45.7 0.0 1DL+1WLR
RIGT COL. -22.3 33.2 0.0 1DL+1SEI

301
302
303
304
305
NOTES:

306
SALES OFFICE CONTACT DETAILS
SALES OFFICE CONTACT NO. EMAIL ID
KUWAIT (965)24962700 [email protected]
DAMMAM (966)138331678 [email protected]
RIYADH (966)114763334 [email protected]
JEDDAH (966)126600139 [email protected]
DUBAI (971)42591192 [email protected]
ABU DHABI (971)26260024 [email protected]
BAHRAIN (973)17214168 [email protected]
QATAR (974)44439973 [email protected]
OMAN (968)24478935 [email protected]

EGYPT (202)24173892 [email protected]

YEMEN (9671)202837 [email protected]
JORDAN (962)65526540 [email protected]
ETHIOPIA (251)911255400 [email protected]
SUDAN (249)183228050 [email protected]
TANZANIA (255)776607547 [email protected]
NIGERIA (234)7045660669 [email protected]

LAHORE (92)4235172473 [email protected]

KARACHI (92)2135380072 [email protected]
 HARIDWAR
KUWAIT

RAK, UAE

HYDERABAD
VIETNAM

SALES NETWORK
OUR MARKET
MANUFACTURING
FACILITIES

www.kirbyinternational.com

2016 Edition
Follow us at

Middle East & Africa Corporate Office & India Corporate Office & Southeast Asia Corporate Office &
Kuwait Plant Hyderabad Plant Vietnam Plant
Kirby Building Systems-Kuwait Kirby Building Systems India Pvt Ltd. Kirby Building Systems Southeast Co Ltd
P.O.Box 23933, Safat 13100 Plot No 8-15, IDA Phase III, 7th Floor, SPT Building, 199 Dien Bien Phu,
Kuwait Pashamylaram, Medak Dist. - 502 307 Ward 15, Binh Thanh District,
Telangana, India Hochiminh City, Vietnam
Tel: (965) 2326 2800 Tel.: (91) 8455 224401 / 02 / 03 / 04 Tel.: (84) 5422 1155
Fax: (965) 2326 1793 Fax: (91) 8455 224419 / 27 Fax: (84) 5422 1156
Email: [email protected] Email: [email protected] Email: [email protected]

Ras Al Khaimah Plant, UAE Haridwar Plant, India Kirby is a wholly owned subsidiary of
Alghanim Industries
Kirby Building Systems - UAE LLC, Kirby Building Systems India (Uttaranchal)
Al Jazeera Industrial Area II, Pvt. Ltd.
PO Box No. 6624, Plot No 2, Sector 11,
Ras Al Khaimah Integrated Industrial Estate,
UAE. Haridwar, Uttarakhand - 249403, India Alghanim Industries,
Tel.: (971) 7204 3333 Tel: (91) 1334 235317, 235318, 235319 P.O. Box 223, Safat,
Fax: (971) 7244 7830 Fax: (91) 1334 235314, 235397 Kuwait 13003
Email: [email protected] Email: [email protected]