0% found this document useful (0 votes)
270 views2 pages

Fingerprint Door Lock Manual E6092

This document provides instructions for using a Techsense fingerprint lock. It details how to: 1. Modify the default master code and reset the system. 2. Activate the lock by exposing the sensor and keypad. 3. Unlock the lock using fingerprints, passwords, or magnetic tags. 4. Add and delete users using fingerprints, passwords, or tags. 5. Enable and disable passage mode for temporary unlocked access. 6. Modify passwords including the master code. 7. Perform a master reset to restore default settings.

Uploaded by

irene_aye
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
270 views2 pages

Fingerprint Door Lock Manual E6092

This document provides instructions for using a Techsense fingerprint lock. It details how to: 1. Modify the default master code and reset the system. 2. Activate the lock by exposing the sensor and keypad. 3. Unlock the lock using fingerprints, passwords, or magnetic tags. 4. Add and delete users using fingerprints, passwords, or tags. 5. Enable and disable passage mode for temporary unlocked access. 6. Modify passwords including the master code. 7. Perform a master reset to restore default settings.

Uploaded by

irene_aye
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Techsense™ Fingerprint Lock User Manual

E6092

Important:
1. Default master code is “11111111”. Please modify it immediately after installation.
2. System resetting will erase all the fingerprint users and password users. It will restore the master code to
the default value.
3. To activate the lock, slide up the front cover and expose the sensor and keypad, blue light in the sensor
indicates active status. System goes back to “sleeping mode” after 5 seconds if there is no operation.
Close and open the front cover to activate the system.
4. System sound indication
I. Dee- (Short): Keypad pressed
II. Dee— (Long): Operation succeeds
III. Dee- Dee- Dee-: Operation fails
IV. Dee- Dee- Dee- Dee-: Low battery

Functions
Unlocking
1. Using Fingerprint: lift up the front cover to expose the fingerprint sensor, press the registered finger
against fingerprint sensor with normal pressure. Rotate the handle upon successful verification.
2. Using Password: lift up the front cover to expose the keypad, key in 8-digit registered password. Rotate
the handle upon successful verification.

TECHSENSE VENTURE GROUP PTE LTD 1


Tel: 63279051 Fax: 63279026 Email: [email protected] Web: www.techsvg.com
3. Using magnetic tag: Press the button on the magnetic sensor and place the key tag close to the sensor
when the red light starts blinking. Rotate the handle upon successful verification.

Add user
A. Password user
Press ‘1’ + ‘*’ + master code + 3-digit user ID + user password + user password + ‘#’
B. Fingerprint user without user ID
I. Press ‘1’ + ‘#’ + master code + ‘#’
II. Press finger against the sensor with normal pressure
C. Fingerprint user with User ID (if a user’s fingerprint may be deleted in future, please enroll his or her
fingerprint with a User ID)
I. Press ‘1’ + ‘#’ + master code + 3-digit user ID + ‘#’
II. Press finger against the sensor with normal pressure
D. Magnetic tag
I. Press the button on the magnetic sensor and place the “Master Tag” close to the sensor
when the red light starts blinking.
II. Place the “Key Tag” close to the sensor when red and green light blinking alternatively.
The enrollment is done!

User-friendly tips: For users who have dry or peeling fingers, it is suggested to apply more pressure during
enrollment. This is for the purpose of better recognition during usage.

Delete user
A. Delete password user by user ID
Press ‘2’ + ‘*’ + master code + 3-digit user ID+ 3-digit user ID + ‘#’
B. Delete all password users
Press ‘3’ + ‘*’ + master code + ‘#’
C. Delete fingerprint user by user ID
Press ‘2’ + ‘#’ + master code + ‘3-digit user ID’ + ‘3-digit user ID’ + ‘#’
D. Delete all fingerprint users
Press ‘3’ + ‘#’ + master code + ‘#’
E. Magnetic tag
Press the button on the magnetic sensor and place the “Master Tag” close to the sensor
when the red light starts blinking. Hold until the fifth beeping sound.

Passage mode
Under passage mode, the lock will be unlocked once the front cover was lift up. Make sure it is disable when
there is nobody in the house.
A. Enable passage mode: Press ‘*’ + ‘*’ + master code + ‘#’
B. Disable passage mode: Press ‘*’ + ‘*’ + master code + ‘#’

Modify password (Including master code)


Press ‘0’ + ‘*’ + old password + new password + new password + ‘#’
Password can only contain numerical numbers, no ‘#’ or ‘*’allowed

Master reset
I. Open the back cover and remove a battery
II. Press the button ‘1’ and ‘2’ on the keypad and hold
III. Put back battery and hold button ‘1’ and ‘2’ for 10 seconds, a long ‘Dee---’ sound is the indication of
successful master reset

TECHSENSE VENTURE GROUP PTE LTD 2


Tel: 63279051 Fax: 63279026 Email: [email protected] Web: www.techsvg.com

You might also like