Produced on 05/21/2019 with Xpress Selection V8.6.4 - database DIL 13.8.

Project name Monte Ritz

Project address Philippines
Reference -
Client name -
Revision -

Selection parameters of the indoor units can be found under the chapter Indoor unit details
Selection parameters of the outdoor units can be found under the chapter Outdoor unit details
Only the data published in the data book are correct. This program uses close approximations of these data.

1. Material List
Model Qty Description Material cost Install. cost Subtotal
RXMQ4AVE 1 Cooling only VRV IV S PH
RXMQ6AVE 2 Cooling only VRV IV S+RA PH
RXMQ6AVE 1 Cooling only VRV IV S PH
BPMKS967A2 2 BP unit
FTKS71KVM 3 Split FTKS-K - Wall Mounted
FXAQ40PVE 1 VRV AP - Wall Mounted(Flat Panel)
FXAQ50PVE 2 VRV AP - Wall Mounted(Flat Panel)
FXHQ100MAVE 2 VRV H - Ceiling Suspended
KHRP26A22T 3 Refnet branch piping kit
BRC1E63 5 Wired Remote Controller (Navigation Remote
Controller)
KAF952B42 3 Titanium apatite deodorising filter
Wireless R/C 3 Standard accessory for Split Indoor units
Total cost

2. Indoor Unit Details

2.1. Table of Abbreviations
Name Logical name of the device
FCU Device model name
Tmp C Indoor conditions in cooling (dry bulb temp. / wet bulb temp.)
Rq TC Required total cooling capacity
Max TC Available total cooling capacity
TC Total cooling capacity
Rq SC Required sensible cooling capacity
Max SC Available sensible cooling capacity
SC Sensible cooling capacity
Tevap Evaporating temperature of indoor unit coil
Tdis C Indoor unit discharge air temperature in cooling
Tmp H Indoor temperature in heating
Rq HC Required heating capacity
Max HC Available heating capacity
HC Heating capacity
Tdis H Indoor unit discharge air temperature in heating
Airflow Supplied airflow

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 1
Sound Sound pressure low and high
PS Power supply (voltage and phases)
MCA Minimum Circuit Amps
WxHxD WidthxHeightxDepth
Wght Weight of the device

2.2. ACCU-1 - RXMQ6AVE

Capacity data at conditions and connection ratio (93%) as entered
Name FCU Tmp C Rq TC Max TC Rq SC Max SC Tevap Tdis C Tmp H Rq HC Max HC Tdis H Airflow
°C kW kW kW kW °C °C °C kW kW °C cfm
FCU-1 FXHQ100MAVE 27.0 / 19.0 n/a 11.2 n/a 8.0 6.0 11.4 n/a n/a n/a n/a 883
FCU-2 FXAQ40PVE 27.0 / 19.0 n/a 4.5 n/a 3.5 6.0 12.8 n/a n/a n/a n/a 424

Required cooling capacity towards the outdoor unit: 15.7kW.

Simultaneous operation calculation

Name FCU Tmp C TC SC Tmp H HC
°C kW kW °C kW
FCU-1 FXHQ100MAVE 27.0 / 19.0 11.2 8.0 n/a
FCU-2 FXAQ40PVE 27.0 / 19.0 4.5 3.5 n/a n/a
Σ 15.7 n/a

The calculation shows the peak discharge temperatures (lowest temperature in case of cooling mode / highest
temperature in case of heating mode), assuming the indoor unit is running at full load at the given indoor
temperature design conditions. In practice the discharge temperature will modulate based on actual capacity
requirements and during defrost mode (heating mode).
The analysis of the suction and discharge temperature values may help in preventing a cold draft and to ensure a
thermal comfort level.

Name Sound PS MCA WxHxD Wght

dBA A mm kg
FCU-1 37-45 220V 1ph 1.3 1400×195×680 33
FCU-2 34-39 220V 1ph 0.4 1050×290×238 14

Outdoor unit placed at the same level as the indoor units.

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 2
 2.3. ACCU-2 - RXMQ6AVE
Capacity data at conditions and connection ratio (114%) as entered
Name FCU Tmp C Rq TC Max TC Rq SC Max SC Tevap Tdis C Tmp H Rq HC Max HC Tdis H Airflow
°C kW kW kW kW °C °C °C kW kW °C cfm
FCU-3 FXHQ100MAVE 27.0 / 19.0 n/a 8.7 n/a 6.8 9.0 13.7 n/a n/a n/a n/a 883
FCU-4 FTKS71KVM 27.0 / 19.0 n/a 7.1 n/a 5.5 9.0 11.6 n/a n/a n/a n/a 614

Required cooling capacity towards the outdoor unit: 15.8kW.

The sum of the required indoor unit capacities is 15.8kW for cooling.
However, the outdoor unit selection uses reduced load values for cooling of 14.2kW (= -10%).
Be aware that unrealistic reductions may lead to reduced comfort levels, different noise levels or increased wear
and tear.

Simultaneous operation calculation

Name FCU Tmp C TC SC Tmp H HC
°C kW kW °C kW
FCU-3 FXHQ100MAVE 27.0 / 19.0 8.3 6.6 n/a
FCU-4 FTKS71KVM 27.0 / 19.0 6.8 5.2 n/a n/a
Σ 15.0 n/a

The calculation shows the peak discharge temperatures (lowest temperature in case of cooling mode / highest
temperature in case of heating mode), assuming the indoor unit is running at full load at the given indoor
temperature design conditions. In practice the discharge temperature will modulate based on actual capacity
requirements and during defrost mode (heating mode).
The analysis of the suction and discharge temperature values may help in preventing a cold draft and to ensure a
thermal comfort level.

Name Sound PS MCA WxHxD Wght

dBA A mm kg
FCU-3 37-45 220V 1ph 1.3 1400×195×680 33
FCU-4 37-46 1050×290×238 12

Outdoor unit placed at the same level as the indoor units.

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 3
 2.4. ACCU-3 - RXMQ6AVE
Capacity data at conditions and connection ratio (95%) as entered
Name FCU Tmp C Rq TC Max TC Rq SC Max SC Tevap Tdis C Tmp H Rq HC Max HC Tdis H Airflow
°C kW kW kW kW °C °C °C kW kW °C cfm
FCU-5 FTKS71KVM 27.0 / 19.0 n/a 7.1 n/a 5.5 9.0 11.6 n/a n/a n/a n/a 614
FCU-6 FTKS71KVM 27.0 / 19.0 n/a 7.1 n/a 5.5 9.0 11.6 n/a n/a n/a n/a 614

Required cooling capacity towards the outdoor unit: 14.2kW.

Simultaneous operation calculation

Name FCU Tmp C TC SC Tmp H HC
°C kW kW °C kW
FCU-5 FTKS71KVM 27.0 / 19.0 7.1 5.4 n/a
FCU-6 FTKS71KVM 27.0 / 19.0 7.1 5.4 n/a n/a
Σ 14.2 n/a

The calculation shows the peak discharge temperatures (lowest temperature in case of cooling mode / highest
temperature in case of heating mode), assuming the indoor unit is running at full load at the given indoor
temperature design conditions. In practice the discharge temperature will modulate based on actual capacity
requirements and during defrost mode (heating mode).
The analysis of the suction and discharge temperature values may help in preventing a cold draft and to ensure a
thermal comfort level.

Name Sound PS MCA WxHxD Wght

dBA A mm kg
FCU-5 37-46 1050×290×238 12
FCU-6 37-46 1050×290×238 12

Outdoor unit placed at the same level as the indoor units.

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 4
 2.5. ACCU-4 - RXMQ4AVE
Capacity data at conditions and connection ratio (100%) as entered
Name FCU Tmp C Rq TC Max TC Rq SC Max SC Tevap Tdis C Tmp H Rq HC Max HC Tdis H Airflow
°C kW kW kW kW °C °C °C kW kW °C cfm
FCU-7 FXAQ50PVE 27.0 / 19.0 n/a 5.6 n/a 4.2 6.0 13.3 n/a n/a n/a n/a 530
FCU-8 FXAQ50PVE 27.0 / 19.0 n/a 5.6 n/a 4.2 6.0 13.3 n/a n/a n/a n/a 530

Required cooling capacity towards the outdoor unit: 11.2kW.

Simultaneous operation calculation

Name FCU Tmp C TC SC Tmp H HC
°C kW kW °C kW
FCU-7 FXAQ50PVE 27.0 / 19.0 5.6 4.2 n/a
FCU-8 FXAQ50PVE 27.0 / 19.0 5.6 4.2 n/a n/a
Σ 11.2 n/a

The calculation shows the peak discharge temperatures (lowest temperature in case of cooling mode / highest
temperature in case of heating mode), assuming the indoor unit is running at full load at the given indoor
temperature design conditions. In practice the discharge temperature will modulate based on actual capacity
requirements and during defrost mode (heating mode).
The analysis of the suction and discharge temperature values may help in preventing a cold draft and to ensure a
thermal comfort level.

Name Sound PS MCA WxHxD Wght

dBA A mm kg
FCU-7 37-42 220V 1ph 0.5 1050×290×238 14
FCU-8 37-42 220V 1ph 0.5 1050×290×238 14

Outdoor unit placed at the same level as the indoor units.

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 5
 3. Outdoor Unit Details
3.1. Table of Abbreviations
Name Logical name of the device
Model Device model name
Tmp C Outdoor temperature in cooling
CC Available cooling capacity
Rq CC Required cooling capacity
Tmp H Outdoor conditions in heating (dry bulb temp. / wet bulb temp.)
HC Available heating capacity (integrated heating capacity)
Rq HC Required heating capacity
Piping Largest distance from indoor unit to outdoor unit
Bse Refr Standard factory refrigerant charge (5m actual piping length)
excluding extra refrigerant charge
For calculation of extra refrigerant charge refer to the databook
PS Power supply (voltage and phases)
MCA Minimum Circuit Amps
WxHxD WidthxHeightxDepth
Wght Weight of the device

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 6
 3.2. Outdoor Details
Name Model Comb Tmp C CC Rq CC Tmp H HC Rq HC
% °C kW kW °C kW kW
ACCU-1 RXMQ6AVE 93 35.0 16.0 15.7
ACCU-2 RXMQ6AVE 114 35.0 15.0 14.2
ACCU-3 RXMQ6AVE 95 35.0 14.3 14.2
ACCU-4 RXMQ4AVE 100 35.0 11.2 11.2

Name Model Piping Refrigerant

m Type Bse Refr Ex Refr
kg kg
ACCU-1 RXMQ6AVE 7.5 R410A 3.6 n/a
ACCU-2 RXMQ6AVE 7.5 R410A 3.6 n/a
ACCU-3 RXMQ6AVE 7.5 R410A 3.6 n/a
ACCU-4 RXMQ4AVE 7.5 R410A 2.9 n/a

Name Model PS MCA WxHxD Wght

A mm kg
ACCU-1 RXMQ6AVE 220V 1ph 27 900×1345×320 104
ACCU-2 RXMQ6AVE 220V 1ph 27 900×1345×320 104
BP 1 BPMKS967A2 230V 1ph 0.25 294×180×350 8
ACCU-3 RXMQ6AVE 220V 1ph 27 900×1345×320 104
BP 2 BPMKS967A2 230V 1ph 0.45 294×180×350 8
ACCU-4 RXMQ4AVE 220V 1ph 16.5 940×990×320 71

3.2.1. ACCU-1 - RXMQ6AVE

Model Qty Description Material cost Install. cost Subtotal
RXMQ6AVE 1 Cooling only VRV IV S PH
FXAQ40PVE 1 VRV AP - Wall Mounted(Flat Panel)
FXHQ100MAVE 1 VRV H - Ceiling Suspended
KHRP26A22T 1 Refnet branch piping kit
BRC1E63 2 Wired Remote Controller (Navigation Remote Controller)
Total cost

Piping Limitations
Maximum total length 300.0m
Maximum longest actual length 120.0m
Maximum longest equivalent length 150.0m
Maximum equivalent length (size up of main pipe required if longer) 89.9m
Maximum length first branch to indoor unit (size up of intermediate pipes required if longer) 40.0m
Maximum length first branch to indoor units 40.0m
Maximum length of indoor units to nearest branch 888.0m
Maximum length difference between longest and shortest distance to indoor units 888.0m
Maximum height difference between indoor units 15.0m
Connection ratio range 50-130%

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 7
Pipe Capacities
Maximum Connection Index Diameters
195 ⅜"×⅝"
> 195 ⅜"×⅝"
Main pipe size up ⅜"×⅞"

3.2.2. ACCU-2 - RXMQ6AVE

Model Qty Description Material cost Install. cost Subtotal
RXMQ6AVE 1 Cooling only VRV IV S+RA PH
BPMKS967A2 1 BP unit
FTKS71KVM 1 Split FTKS-K - Wall Mounted
FXHQ100MAVE 1 VRV H - Ceiling Suspended
KHRP26A22T 1 Refnet branch piping kit
BRC1E63 1 Wired Remote Controller (Navigation Remote Controller)
KAF952B42 1 Titanium apatite deodorising filter
Wireless R/C 1 Standard accessory for Split Indoor units
Total cost

Piping Limitations
Maximum total length 250.0m
Maximum longest actual length 100.0m
Maximum longest equivalent length 125.0m
Maximum equivalent length (size up of main pipe required if longer) 888.0m
Maximum length first branch to indoor unit (size up of intermediate pipes required if longer) 30.0m
Maximum length first branch to indoor units 70.0m
Maximum length of indoor units to nearest branch 888.0m
Maximum length difference between longest and shortest distance to indoor units 888.0m
Maximum height difference between indoor units 15.0m
Connection ratio range 50-130%
Maximum height difference between outdoor unit and BP units 40.0m
Maximum height difference between BP units 15.0m

Pipe Capacities
Maximum Connection Index Diameters
149.9 ⅜"×⅝"
> 149.9 ⅜"×¾"
Main pipe size up ⅜"×⅞"

3.2.3. ACCU-3 - RXMQ6AVE

Model Qty Description Material cost Install. cost Subtotal
RXMQ6AVE 1 Cooling only VRV IV S+RA PH
BPMKS967A2 1 BP unit
FTKS71KVM 2 Split FTKS-K - Wall Mounted
KAF952B42 2 Titanium apatite deodorising filter
Wireless R/C 2 Standard accessory for Split Indoor units
Total cost
The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 8
Piping Limitations
Maximum total length 250.0m
Maximum longest actual length 100.0m
Maximum longest equivalent length 125.0m
Maximum equivalent length (size up of main pipe required if longer) 888.0m
Maximum length first branch to indoor unit (size up of intermediate pipes required if longer) 30.0m
Maximum length first branch to indoor units 70.0m
Maximum length of indoor units to nearest branch 888.0m
Maximum length difference between longest and shortest distance to indoor units 888.0m
Maximum height difference between indoor units 15.0m
Connection ratio range 50-130%
Maximum height difference between outdoor unit and BP units 40.0m
Maximum height difference between BP units 15.0m

Pipe Capacities
Maximum Connection Index Diameters
149.9 ⅜"×⅝"
> 149.9 ⅜"×¾"
Main pipe size up ⅜"×⅞"

3.2.4. ACCU-4 - RXMQ4AVE

Model Qty Description Material cost Install. cost Subtotal
RXMQ4AVE 1 Cooling only VRV IV S PH
FXAQ50PVE 2 VRV AP - Wall Mounted(Flat Panel)
KHRP26A22T 1 Refnet branch piping kit
BRC1E63 2 Wired Remote Controller (Navigation Remote Controller)
Total cost

Piping Limitations
Connected indoor type(s): VRV
Maximum total length 250.0m
Maximum longest actual length 50.0m
Maximum longest equivalent length 65.0m
Maximum equivalent length (size up of main pipe required if longer) 888.0m
Maximum length first branch to indoor unit (size up of intermediate pipes required if longer) 40.0m
Maximum length first branch to indoor units 40.0m
Maximum length of indoor units to nearest branch 888.0m
Maximum length difference between longest and shortest distance to indoor units 888.0m
Maximum height difference between indoor units 10.0m
Connection ratio range 50-130%

Pipe Capacities
Maximum Connection Index Diameters
130 ⅜"×⅝"
> 130 ⅜"×⅝"
The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 9
Main pipe size up ⅜"×¾"

4. Piping Diagrams
Pipes marked with * in the diagrams must be connected to the device with a reducing joint.

R
CCU
A
X MQ
-1
6 A
VE

⅜ "× ¾ "*
KH
RP2
⅜ "×
A2 2
6 T
⅝"

XH
F
CU
F - 1
Q1 0 M
AVE
4.1. Piping ACCU-1
¼ "×
½"

CU
F - 2
FX
A Q4
0 P
VE

Warning: The pipe diameter values are purely indicative. Depending on the required pipe lengths, a
different pipe diameter might be required.

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 10
 AC U-2
R MQX 6AV E

⅜"× ¾"
K HRP 26A 2T
⅜"× ⅝"

FCU -3
FXH 10Q 0MA VE
4.2. Piping ACCU-2
⅜"× ⅝" * ¼"× ⅝"

BP 1 FCU -4

BPM KS9 67A 2 FTK S71 KVM

Warning: The pipe diameter values are purely indicative. Depending on the required pipe lengths, a
different pipe diameter might be required.

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 11
A CU -3
RX MQ6 AV E

⅜ "×¾ "

BP 2
BPM SK 967 A2
¼ "×⅝ "

FCU -5
FTK 7S 1KV M
4.3. Piping ACCU-3
¼ "×⅝ "

FCU -6

FTK S7 1KV M

Warning: The pipe diameter values are purely indicative. Depending on the required pipe lengths, a
different pipe diameter might be required.

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 12
 CCU
A
X MQ
R
-4
4 A

⅜ "×
⅝"
VE

KH
RP2
¼ "×
A2 2
6 T
½"

FX
CU
F
A Q5
- 7
0 P
VE
4.4. Piping ACCU-4
¼ "×
½"

CU
F - 8

FX
A Q5
0 P
VE

Warning: The pipe diameter values are purely indicative. Depending on the required pipe lengths, a
different pipe diameter might be required.

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 13
 5. Wiring Diagrams
P1P2 = Please select the cable type and size in accordance with the databook.
F1F2 = Please select the cable type and size in accordance with the databook.

L,N
AC CU-1
R MQX 6A VE
INF 1,F2
27A 1p h
FCU -1
P 1,P2
F XHQ 01 MAV EL
F1, 2F
BRC 1E6 3

,N 1 .3A 1ph
5.1. Wiring ACCU-1
P 1,P2
FCU -2 BRC 1E6 3
FXA 4Q 0PV EL
F1, F2 ,N 0 .4A 1ph

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 14
A CU-2
RXM Q6AV E
IN F1,2

L,N 27 A1ph
FCU- 3
P1, 2 BR C1E6 3
FX Q10H 0MAV EL,
F1 F2, N 1. 3A1p h
5.2. Wiring ACCU-2
L, N0. 25A1 ph
BP 1 FCU- 4 W irels sR/C
BP KS9M 67A2 FT S71K KVM
F1 F2,

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 15
A CU-3
RXM Q6AV E
IN F1,2

L,N 27 A1ph
BP 2
BP KS9M 67A2
F1 F2,
L, N0. 45A1 ph
FCU- 5
FT S71K KVM
W irels sR/C
5.3. Wiring ACCU-3
FCU- 6 W irels sR/C
FT S71K KVM

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 16
L,N
AC CU-4
R MQX 4A VE
INF 1,F2

1 6.5A 1p h
F1, F2
FCU -7
P 1,P2 BRC 1E6 3
FXA 5Q 0PV EL
,N 0 .5A 1ph
5.4. Wiring ACCU-4
P 1,P2
FCU -8 BRC 1E6 3
FXA 5Q 0PV EL
F1, F2 ,N 0 .5A 1ph

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 17
 6. Device Options
6.1. Indoor Unit Options
Model Description Used by
KAF952B42 Titanium apatite deodorising filter FCU-4 [FTKS71KVM] FCU-5 [FTKS71KVM] FCU-6 [FTKS71KVM]

The Xpress Selection Program is property of Daikin Europe NV. Daikin Europe NV cannot be held liable for any inaccuracy, reliability of the outcome of the Xpress Selection
Program.

Page 18