www.ejointech.

com GSM/CDMA/WCDMA Gateway

Ejoin

GoIP User Manual

Shenzhen Ejoin Technology Co., Ltd.

 www.ejointech.com GSM/CDMA/WCDMA Gateway

CONTENT

1 Introduction........................................................................................................................................... 4

1.1 Overview ................................................................................................................................. 4

1.2 Glossary.................................................................................................................................. 4

2 Equipment Information....................................................................................................................... 5

2.1 Product Brief.......................................................................................................................... 5

2.2 Appearance ............................................................................................................................ 5

2.3 Special Features ................................................................................................................... 6

2.4 Specification .......................................................................................................................... 7

2.5 Mobile Features ..................................................................................................................... 8

2.6 Maintenance and Management ......................................................................................... 8

3 Equipment Installation........................................................................................................................ 9

3.1 Network Setup ....................................................................................................................... 9

3.2 Equipment IP Address ...................................................................................................... 10

3.3 Equipment Connection...................................................................................................... 10

3.4 LED Indicators..................................................................................................................... 10

4 Web Settings ....................................................................................................................................... 11

4.1 Login ...................................................................................................................................... 11

4.2 Basic Settings ..................................................................................................................... 12

4.3 SIP Protocol ......................................................................................................................... 14

4.4 GoIP Settings ....................................................................................................................... 17

4.4.1 Port Settings .................................................................................................................... 17

4.4.2 Base Stations .................................................................................................................. 19

4.4.3 IMEI Settings .................................................................................................................. 21

4.4.4 PIN Settings .................................................................................................................... 23

4.4.5 SMS Send ........................................................................................................................ 23

Shenzhen Ejoin Technology Co., Ltd. 1
www.ejointech.com GSM/CDMA/WCDMA Gateway
4.4.6 SMS Receive................................................................................................................... 26

4.4.7 Lock/Switch Card .......................................................................................................... 28

4.4.8 Port Inter-Calling ........................................................................................................... 32

4.4.9 SIM Num Settings ......................................................................................................... 33

4.4.10 AT Command ................................................................................................................. 34

4.4.11 Billing Settings .............................................................................................................. 35

4.4.12 Call Dur. Control ........................................................................................................... 38

4.5 Application Settings .......................................................................................................... 39

4.5.1 Phone Book .................................................................................................................... 39

4.5.2 Dial Plan........................................................................................................................... 41

4.5.3 Number Translation...................................................................................................... 41

4.5.4 Incoming Translation ................................................................................................... 42

4.5.5 Incoming Black List...................................................................................................... 43

4.5.6 Incoming White List ..................................................................................................... 44

4.6 Advanced Settings ............................................................................................................. 45

4.6.1 Network ............................................................................................................................ 45

4.6.2 Voice and Codec ........................................................................................................... 46

4.6.3 other settings ................................................................................................................. 47

4.7 System Settings .......................................................................................................................... 49

4.7.1 User Mgmt ....................................................................................................................... 49

4.7.2 Device Mgmt ................................................................................................................... 51

4.7.3 File Management ........................................................................................................... 52

4.7.4 System Update............................................................................................................... 52

4.8 Debugging Tools......................................................................................................................... 54

4.8.1 Test Network .................................................................................................................. 54

4.9 Running Status ............................................................................................................................ 55

4.9.1 Port Status ...................................................................................................................... 55

4.9.2 Call Status ....................................................................................................................... 57

4.9.3 System Status ................................................................................................................ 57

Shenzhen Ejoin Technology Co., Ltd. 2

 www.ejointech.com GSM/CDMA/WCDMA Gateway
4.9.4 Call Statistics ................................................................................................................. 58

4.9.5 Inter-call Stats ................................................................................................................ 59

4.10 Save and Reboot....................................................................................................................... 60

5 Typical Used Scenario ...................................................................................................................... 61

5.1 Landing from IP to Mobile Network ............................................................................... 61

5.2 Access from Mobile Network to IP ................................................................................. 62

Shenzhen Ejoin Technology Co., Ltd. 3

www.ejointech.com GSM/CDMA/WCDMA Gateway

1 Introduction

1.1 Overview

A VoIP GSM Gateway (GoIP Gateway) is a device which reduces costs when
calling from a fixed telephone line to mobile network. It enables direct routing
between IP, digital, analog and mobile networks.
GoIP Gateway is now used more and more for telephone carriers to land their IP
calls to mobile network. In those areas where fixed line services are unavailable
or much more expensive than the mobile cost, GoIP Gateway is an irreplaceable
alternative.
The following figure shows a basic topology of GoIP Gateway usage.

1.2 Glossary

VoIP: Voice over Internet Protocol.

SIP: Session Initial Protocol.
DTMF: Dual Tone Multiple Frequency.
IMEI: International Mobile Equipment Identity.
LCR: Least Cost Routing.
USSD: Unstructured Supplementary Service Data.
GSM: Global System Communications.
CDMA: Code Division Multiple Access.
W CDMA: Wideband Code Division Multiple Access.

Shenzhen Ejoin Technology Co., Ltd. 4

 www.ejointech.com GSM/CDMA/WCDMA Gateway

2 Equipment Information

2.1 Product Brief

ACOM516 GSM/CDMA/WCDMA series VoIP Gateway is a multi-functional and

high performance product, which is designed with advanced embedded technology.
ACOM516 series is able to process traditional voice call service and internet data
service. Compare to the ACOM508 GSM/CDMA/WCDMA series VoIP Gateway,
ACOM516 series adopt new hardware and software structure, which supports up to 16
concurrent calls and perfectly support G729a/b/e、G723.1、G.711 a/u law and iLBC
codecs at the same time.
ACOM516 series VoIP Gateway includes: ACOM516-16, ACOM516-64, most of
their features and structure are same, please check the following table about the
difference:
Channel Sim capacity in Total sim capacity

each channel
ACOM516-16 16 1 16
ACOM516-64 16 4 64

2.2 Appearance

Here, we take ACOM516-64 as the sample to show the interface and indicators at the
front and back panel.
Back Panel

Front Panel
Shenzhen Ejoin Technology Co., Ltd. 5
www.ejointech.com GSM/CDMA/WCDMA Gateway

 16 Antennas
 1 USB Serial Port (Baudrate 115200)
 2 Network Interface (RJ45)
 1 Power Interface (DC 12V 5A)
 1 Reset Button
 64 sim card slots
 64 LED lights

2.3 Special Features

 Support G729a/b/e,G723.1,G.711 A/U law, iLBC auto-selecting

 EBO(Ejoin Bandwidth Optimization)
 Proxy Encryption Solution for IP Block
 Support SIM Bank
 VPN(pptp)
 SIM Card Rotating(ACOM516-64)
 Solution to solve the SIM card blocked by:
 Accumulated Call Duration
 Accumulated Connected Calls
 Accumulated Calls
 Consecutive Failed Calls
 Consecutive No-Alert Calls
 Consecutive No-Answer Calls
 Consecutive No Carrier Calls
 Consecutive Short-Duration Calls
 Station intelligent switching
 ERMS(Ejoin Remote Management System)
 Port Inter-Calling
 Fake Ringback

Shenzhen Ejoin Technology Co., Ltd. 6

 www.ejointech.com GSM/CDMA/WCDMA Gateway
 Call Duration Limitation for SIM Card/Single
 Dial Plan/Prefix Inward Translation/Intelligent Routing
 Web Browser: Firefox/Chrome /IE/Opera

2.4 Specification

Model ACOM 516-16/64

Number of Channels 16 channels
GSM: 850/900/1800/1900MHz
Frequency CDMA:450/800/1900MHz
WCDMA:850/900/1800/1900/2100MHz
SIP/2.0 RFC3261
SIP Specification Session Timer RFC4028
STUN
DHCP/PPPoE/VPN(pptp)
NTP Telnet/HTTP/FTP/TFTP
Network Protocols
Encryption:Ejoin,VOS2000,RC4,XOP.Base64

Hot-line call ,Dial plan, Speed dial, Phone book, CDR, LCR,
Telephony Features
White/Black list
DTMF tone dectection/generation
DTMF relay: in-band, RFC 2833 and SIP info
Telephony Signaling Call forward: unconditional, no answer and busy
N-way conferencing
Caller ID display/generation, Mobile Number Portability
Voice codecs:G729a/b/e,G723.1,G.711 A/U law, iLBC
Echo cancellation
Silence suppression & detection（VAD, CNG）
Voice Capability
Adaptive jitter buffer
Volume adjustable
IVR customized

1 WAN 10/100Base-T ethernet(RJ-45 connector)

Number of Ports 1 LAN 10/100Base-T ethernet(RJ-45 connector)
1 Console(USB)
LEDs 1 Power and 16 groups of card online and running status indicator
Power Supply 100-240VAC, 50 - 60 Hz IN, 12V/5A OUT
Operating Operating temperature: 0 - 50ºC
Environment Operating humidity: 10 – 90%RH
Warranty 12 Months

Shenzhen Ejoin Technology Co., Ltd. 7

www.ejointech.com GSM/CDMA/WCDMA Gateway

2.5 Mobile Features

 SMS Send, Receive and Forward(GSM/SIP/HTTP)

 SMS Inbox
 AT Command , USSD
 SMS Format: PDU/TXT
 PIN Code Management
 CDMA Delay Answer
 GSM Polarity Reversal
 Carrier Selection
 Caller ID Hidden(need SIM Card support)

2.6 Maintenance and Management

 Multi-language Interface
 USB Serial COM
 Configuration Backup and Restore
 Support HTTP/TFTP Upgrade
 Call statistics: ASR,ACD,PDD
 Ejoin Remote Management System

Shenzhen Ejoin Technology Co., Ltd. 8

www.ejointech.com GSM/CDMA/WCDMA Gateway

3 Equipment Installation

This chapter describes how to install a new GoIP Gateway to a physical network
environment, how to initialize it and start it in a proper way.

3.1 Network Setup

Network is a prerequisite to install GoIP Gateway. The following figure shows the
topology of LAN with a VoIP Gateway connected.

WAN

IP network

Switch/Router

Shenzhen Ejoin Technology Co., Ltd. 9

 www.ejointech.com GSM/CDMA/WCDMA Gateway
3.2 Equipment IP Address

The default IP of GoIP Gateway WAN port is 192.168.1.67, while the default

LAN port IP is 192.167.1.1.

3.3 Equipment Connection

Follow the steps below to install the GoIP Gateway to LAN.

1) Fix the antenna to the GoIP Gateway. (Optional)

2) Insert SIM card(s) to slots.
3) Connect an Ethernet Cable to the WAN port of GoIP Gateway. The other end
of the Ethernet Cable should be connected to LAN port of route or switch.
4) Connect an Ethernet Cable to the LAN port of GoIP Gateway. The other end
of the Ethernet Cable should be connected to PC or other network device.
(Optional)
5) Plug in the GoIP Gateway.

3.4 LED Indicators

There are a set of LED lights in the front of GoIP Gateway. Lights will be on or
glittering when the GoIP Gateway is power on and running. The following table
describes various meanings of status corresponding to LED lights in different
display color.

Power It indicates whether the system is running or not.

Calling It indicates which module is calling.
Chosen card It indicates was chosen.

Shenzhen Ejoin Technology Co., Ltd. 10

 www.ejointech.com GSM/CDMA/WCDMA Gateway

4 Web Settings

This chapter describes how to set up GoIP Gateway through W eb Page. There is
a built-in web server which can be accessed at URL: http://GATEWAY_IP/, while
GATEWAY_IP is the WAN IP address of the GoIP Gateway, such as
192.168.1.67.

As an example, the following introduction will base on the GoIP Gateway with

WAN IP 192.168.1.67.

4.1 Login

Open web browser and access URL http://192.168.1.67/. The default login page
will be displayed as following.

The default login account and password are:

Account root
Password root

Shenzhen Ejoin Technology Co., Ltd. 11

 www.ejointech.com GSM/CDMA/WCDMA Gateway
It is recommended to use IE or FireFox to access the web pages. After
successfully logged in, the main page to set Gateway is as following:

4.2 Basic Settings

Basic Settings will be described in this paragraph. The most frequently modified
parameters and most of the individual parameters are listed in this page.

WAN port is to connect to switch or route then you can use PC that on the same

LAN to login. There’s three types of wan.

Static IP: You can set WAN IP,IP Mask, Default Gateway and DNS Server of

WAN port to connect the Internet.

Shenzhen Ejoin Technology Co., Ltd. 12

www.ejointech.com GSM/CDMA/WCDMA Gateway

Dynamic IP:You can get IP address ,IP Mask ,Default Gateway and DNS
Server dynamically from your DHCP server.

PPPoE:In this mode,you can use GOIP device to dail-up network. You can
set User Name and Password which you get from your ISP. And you also can set
MTU and Service Name.

SIP Server Settings is for SIP communication with IP network. Fields are
specified as following:
 Protocol Mode: Specify SIP client working mode. Option values are
Registration/Point-to-Point. If set to Registration, SIP client will send registration
messages to SIP server.
 Encryption Method: Specify the encryption method for messages between
SIP server and SIP client.
 SIP Server IP: Specify the IP of SIP server.
 SIP Server Port: Specify the port of SIP server.
 Phone Number: Specify the caller phone number for SIP client. It can also be
regarded as the SIP port number which can be called.

Shenzhen Ejoin Technology Co., Ltd. 13

 www.ejointech.com GSM/CDMA/WCDMA Gateway
 Account: Specify the SIP account for registration.
 Password: Specify the SIP password for registration.

Note: The settings of Phone Number, Account and Password are globally active.
They will apply to all SIP ports settings in SIP Protocol page.

4.3 SIP Protocol

SIP Protocol Settings will be described in this paragraph. It mainly targets to set
up parameters related to SIP server, SIP account and SIP password for SIP
registration.

The screenshot below shows the operation mode to set SIP running parameters.

Fields are specified as following:

 Protocol Mode: It is the same as that in Basic Settings. The modification here will
also apply to Basic Settings page.
 Encryption Mode: It is the same as that in Basic Settings. The modification here will
also apply to Basic Settings page.
 SIP Server: Specify the domain or IP of the SIP Server.
 SIP Server Port: Specify the port of the SIP Server.
 Primary Proxy IP: Specify the primary proxy IP.
 Secondary Proxy IP: Specify the secondary proxy IP.
 Expiration Period: Specify the expiration period for registration.
 Local Port: Specify the local port used to register to SIP server.
 Multiple Port Support: Specify whether support to register to SIP server with different
Shenzhen Ejoin Technology Co., Ltd. 14
www.ejointech.com GSM/CDMA/WCDMA Gateway
SIP Account.
 Use Phone Number: Specify whether enable phone number registration or not.
If set to Enabled, the Phone Number and Account can be different when registering
to SIP Server. If set to Disabled, the Phone Number must be the same as the
Account when registering, otherwise, the registration will fail.
 Receive All Call: Specify whether enable to receive all calls or not.
 Drop Account Prefix: Specify whether enable drop account prefix. If set to enabled, it
will remove the account prefix presented in callee number.
 Auto Resp 183: Specify whether enable auto resp 183 or not. If set to enabled,it will
send 183-session-progress immediately for a incoming invite.
 No Line Code: specify the sip code when no available line.

The screenshot below shows the operation mode to set STUN

STUN is a standardized set of methods and a network protocol to allow an end

host to discover its public IP address if it is located behind a NAT. It is used to
pemit NAT traversal for applications of real-time voice, video, messaging, and
other interactive IP communications.
If you have the STUN server,enable STUN support,fill the server ip and
port(default port is 3478),it will work.

The screenshot below shows the operation mode to Proxy Encryption

Proxy Encryption is a good solution for protecting ip from blocking and save
bandwidth about 50%. Fields are specified as following:

Shenzhen Ejoin Technology Co., Ltd. 15

www.ejointech.com GSM/CDMA/WCDMA Gateway
 Proxy Encryption: Specify whether enable it, if enabled, system will automatically
disable common encryption.
 Proxy Server IP: Specify the proxy server ip.
 Proxy Server Port: Specify the port of the proxy server, the default proxy server port
is 38080.
 Transport Protocol: Specify the transport protocol. Option values are UDP/TCP,UDP
has better voice quality, TCP is more security.
 Encryption Method: Specify the encryption method, the default encryption method
RC4,other two method are XOR and BASE64.
 Encryption key: Specify the encryption key.

The screenshot below shows the operation mode to SIP Account

If a default Phone Number, Account and Password is already set in Basic

Settings page, all the inputs here can be left empty and the default setting will
apply to all the SIP accounts. For example, if an account test is set with
password 888888 in Basic Settings page and all the SIP accounts here are left
empty, the combination of test and 888888 will be used for all SIP accounts to
register to SIP Server. When the gateway register on the server successfully, the
status will show ready.

There are two ways to overwrite the default SIP account setting in Basic Settings
page.

1) Assign an account and password to Port 1 and leave empty for other Ports.
Settings of Port 1 can also be applied to all the other Ports automatically.
This is for short to set Account and Password if all the Ports use the same

Shenzhen Ejoin Technology Co., Ltd. 16

 www.ejointech.com GSM/CDMA/WCDMA Gateway
value.

2) Assign account and password to certain Port(s). The value of account and
password can be various. In this scenario, only the Ports assigned with
account and password will register to SIP Server.

4.4 GoIP Settings

GoIP settings include:

 Port Settings
 LocNum Settings
 Base Stations
 IMEI Settings
 PIN Settings
 SMS Send
 SMS Receive
 Lock/Switch Card
 Por Inter-Calling
 AT Command
 Billing Settings

These sub topics will be introduced separately below.

4.4.1 Port Settings

The screenshot below shows the operation mode to set Basic Settings of Port settings

It’s for choosing the frequency band and whether lock the operator, generally, we don’t
enable the lock the operator. When the gateway can’t detect the sims, we need to
enable Unnormal Sim Supp.

The screenshot below shows the operation mode to set Hardware properties.

Shenzhen Ejoin Technology Co., Ltd. 17

 www.ejointech.com GSM/CDMA/WCDMA Gateway

The columns are specified as following:

 Port No: The GoIP Gateway mobile port. Each port contains one or four card slots.
Port No starts from 1 to 16.

 Bind SIM Card: The SIM card that not bind will be locked by gateway.
 Mobile Base: The default setting is auto which makes the devices to choose mobile
base automatically. What’s more, you can choose mobile base manually.
 Provider: Specify the provider.
 Input Volume: Specify the input voice volume of this port.
 Output Volume: Specify the output voice volume of this port.
 IMEI: Specify the IMEI of this port. Any card in this port will use this specified
 IMEI to communicate with mobile base.

The screenshot below shows the operation mode to set port application
feature.

Shenzhen Ejoin Technology Co., Ltd. 18

 www.ejointech.com GSM/CDMA/WCDMA Gateway

The columns are specified as following:

 Port No: The GoIP Gateway mobile port. Each port contains one or four card slots.
Port No starts from 1 to 16.

 Main Access: Specify whether the current port is used for access or not. If set to
Enable, any call made to the card in this port will be redirected to the phone number
on any other idle port which is not set as a main access. The any other idle port may
be either on the same GoIP Gateway or on another GoIP Gateway which keeps
reporting its port status to a Notification Server.
 Check Balance: Specify whether need to check card balance.
 Card Number: Specify the card number.
 Balance: Specify the balance of the card.
 SMS Forward To: Specify a receiver to which the SMS, which is sent to the card on
this port, will be forwarded. The country code must be prefixed, for example,
8613512345678, while the string 86 stands for the country code of China and
13512345678 is the China Mainland mobile phone number.
 SMS Center: Specify the code of SMS Center.

4.4.2 Base Stations

The screenshot below shows the operation mode to set globally for base
Shenzhen Ejoin Technology Co., Ltd. 19
 www.ejointech.com GSM/CDMA/WCDMA Gateway
stations.

Fields are specified as following:

 Max Channels: Specify the max base stations

 Lowest Valid Signal: Specify the lowest valid signal
 Switch period: Specify the period of switching base station
 Base Balancing: Specify whether enable base balancing, we suggest disable it.

The screenshot below shows the operation mode to set base stations settings and
operations

Fields are specified as following:

 Port No: The GoIP Gateway mobile port. Each port contains one or four card slots.
Port No. starts from 1 to 16.
Shenzhen Ejoin Technology Co., Ltd. 20
 www.ejointech.com GSM/CDMA/WCDMA Gateway
 Base Selection: the default base selection mode is auto which makes the devices to
choose mobile base automatically, if you want to switch base station periodically,
pleasure select Poll, and you can set the switch period.
 Base Station: Specify the base station.
 White List: Specify the white list of base station.
 Black List: Specify the black list of the base station.
 Operations: When click the refresh button will change a new base station.

4.4.3 IMEI Settings

The screenshot below shows the operation mode to set IMEI for each card
inserted in GoIP Gateway port.

Fields are specified as following:

 Port No: The GoIP Gateway mobile port. Each port contains one or four card slots.
Port No. starts from 1 to 16.

 IMEI A: Specify the IMEI for card A of the port.

 IMEI B: Specify the IMEI for card B of the port.
 IMEI C: Specify the IMEI for card C of the port.
 IMEI D: Specify the IMEI for card D of the port.

The specified IMEI, instead of the default IMEI of the card, will be used for the
Shenzhen Ejoin Technology Co., Ltd. 21
 www.ejointech.com GSM/CDMA/WCDMA Gateway
corresponding card to communicate with mobile base.

The screenshot below shows the operation mode to set Dynamic IMEI for each
card of the designated port. If a card on a port is assigned with a group of
IMEIs, it will randomly use any of the IMEI in group to communicate with mobile
base.

Add New

Click button Add New to expand the data input area to add new data. Fields are
specified as following:

 Data Status: Mark the status of current data record. Option values are Add/Edit.
Value Add means the data is new while value Edit means the data is old.
 IMEI Start: Specify an initial IMEI value for the IMEI group.
 IMEI Size: Specify the size of the IMEI group.

Click button Submit on the right to save the new data record.

Edit

All the records are displayed in list. Two operations are provided on the right of
each record. Click Edit to expand the current data record to Data Detail Area
which is above the Data List.

Click button Submit on the right to save the old data record.

Delete

Click Delete on the right of each record to delete the current record. A message
box will be popped for delete confirmation.
Shenzhen Ejoin Technology Co., Ltd. 22
 www.ejointech.com GSM/CDMA/WCDMA Gateway
4.4.4 PIN Settings

The screenshot below shows the operation mode to set globally for PIN settings

Fields are specified as following:

 PIN Unblock: Specify whether enable the pin unblock.

The screenshot below shows the operation mode to set port PIN.

Fields are specified as following:

 Port No: The GoIP Gateway mobile port. Each port contains one or four card slots.
Port No. starts from 1 to 16.

 PIN A: Specify the PIN for card A of the port.

 PIN B: Specify the PIN for card B of the port.
 PIN C: Specify the PIN for card C of the port.
 PIN D: Specify the PIN for card D of the port.
The specified PIN, will be used for unblocking the corresponding card.

4.4.5 SMS Send

The screenshot below shows the operation mode to set basic settings.
Shenzhen Ejoin Technology Co., Ltd. 23
 www.ejointech.com GSM/CDMA/WCDMA Gateway

Fields are specified as following:

 SMS Format: Specify the sms format.

 Forward Protocol: Specify forward protocol.

The screenshot below shows the operation mode to set sip protocol of forwarding sms.

Fields are specified as following:

 Forward Protocol: Specify forward protocol sip.

 Server IP: Specify the sms server ip.
 Content-Type: Specify the Content-Type.
 Content Charset: Specify the content charset.

The screenshot below shows the operation mode to set http protocol of forwarding
sms.

Fields are specified as following:

 Forward Protocol: Specify the forward protocol http.

 URL: Specify the sms server URL.
 Username: Specify the username.
 Password: Specify the password.
 Sender: Specify the sender.
 Receiver: Specify the receiver.

Shenzhen Ejoin Technology Co., Ltd. 24

 www.ejointech.com GSM/CDMA/WCDMA Gateway
 Device Port: Specify the device port.
 Charset: Specify the charset UTF-8.

The screenshot below shows the operation mode to set scheduled sending sms

Fields are specified as following:

 Recipients: Specify the recipients. Semi-colon can be used to separate multiple

receivers.
 Content: Specify the sms content.
 Send To Local SIM:Enable this feature and set the local SIM’s number,the inter port
will send sms.
 By Duration: Gateway will start sms sending by the device online time, and the time
between minimum minutes and maximum minutes.
 By Consecutive Failed Calls:Gateway will start sms sending by consecutive failed
calls.
 By Consecutive Calls:Gateway will start sms sending by consecutive calls.
 By Call Duration:Gateway will start sms sending by call duration.

The screenshot below shows the operation mode to send SMS through the
GoIP Gateway.

Shenzhen Ejoin Technology Co., Ltd. 25

 www.ejointech.com GSM/CDMA/WCDMA Gateway

1) Select port. The module here means GoIP mobile port and the SMS is
sent out through the card which is in service on this port.
2) Input the receivers separated by semi-colon.
3) Input SMS content and click button send to send out the SMS.

Field Received SMS is used to display the last response of the SMS sent out, if
the response is not empty.

Field Successful SMS Number records down the total number of SMS which is
successfully sent out. Field Failed SMS Number records down the total number
of SMS which is sent failed.

4.4.6 SMS Receive

The screenshot below shows the operation mode to receive sms.

Shenzhen Ejoin Technology Co., Ltd. 26

 www.ejointech.com GSM/CDMA/WCDMA Gateway

Fields are specified as following:

 Port No: The GoIP Gateway mobile port. Each port contains one or four card slots.
Port No starts from 1 to 16.

 Sender: Specify the sms sender.

 Time: Specify the sms receive time.
 Content: Specify the sms content.
 Operations: Click the Detail button to get more detail about the specify port.

The screenshot below shows the operation mode to get sms details.

Fields are specified as following:

 Please Select Port: Specify the port.

Shenzhen Ejoin Technology Co., Ltd. 27

 www.ejointech.com GSM/CDMA/WCDMA Gateway

 Please Select SIM: Specify the sim.
 Port: Specify the port.
 Sender: Specify the sms sender.
 Time: Specify the sms receive time.
 Content: Specify the sms content.
 Back: Back to the SMS content web page.
 Refresh: Refresh the web page.
 Batch Delete: Batch delete the sms.
 Reply: Reply the sms
 Delete: Delete the corresponding sms.

4.4.7 Lock/Switch Card

The screenshot below shows the operation mode to set globally for card lock
and switch.

Fields are specified as following:

 SMS Warning: Specify whether enable sms warning.
 SMS Receiver for Warning: Specify the receiver mobile number to receive the
warning SMS for card lock or switch.

The screenshot below shows the operation mode to set conditions for locking
card and switching card.

Fields are specified as following:

 Enable or Not: Specify whether enable the periodic checking or not. If set to Enable,
system will check the card running time periodically. If the continuous running
time reaches or exceeds the specified Period value, this card will be locked and the

Shenzhen Ejoin Technology Co., Ltd. 28

 www.ejointech.com GSM/CDMA/WCDMA Gateway
next card will come into service.
 Reset When Switching: To clear this condition if other conditions to be met when
you enable two or more Lock/switch card conditions
 Accumulated Duration: Specify the period to check.
 Locking Duration: Specify how long the card will be locked. 0 means no lock,-1
means permanent lock

The following is to set condition of accumulated connected calls.

Fields are specified as following:

 Enable or Not: Specify whether enable this condition. If set to Enable, the
accumulated calls will be used as a condition for system to check.
 Reset When Switching: To clear this condition if other conditions to be met when
you enable two or more Lock/switch card conditions
 Connected Calls: Specify the max number of calls on this card. If the Connected
number of calls reaches or exceeds this value, this card will be locked if this
condition is enabled.
 Locking Duration: Specify how long the card will be locked.

The following is to set condition of accumulated calls.

Fields are specified as following:

 Enable or Not: Specify whether enable this condition. If set to Enable, the
accumulated call duration will be used as a condition for system to check.
 Reset When Switching: To clear this condition if other conditions to be met when
you enable two or more Lock/switch card conditions
 Accumulated calls: Specify the max running duration of the card. If the accumulated
call times reaches or exceeds this value, the card will be locked if this
Shenzhen Ejoin Technology Co., Ltd. 29
 www.ejointech.com GSM/CDMA/WCDMA Gateway
condition is enabled.
 Locking Duration: Specify how long the card will be locked.

The following is to set condition of consecutive failed calls.

Fields are specified as following:

 Enable or Not: Specify whether enable this condition. If set to Enable, the
accumulated number of failed calls will be used as a condition for system to check.
 Reset When Switching: To clear this condition if other conditions to be met when
you enable two or more Lock/switch card conditions
 USSD Query: Send USSD query command before switching.
 Failed calls: Specify the max number of consecutive failed calls on this card. If the
number of consecutive failed calls reaches or exceeds this value, the card will be
locked if this condition is enabled.
 Locking Duration: Specify how long the card will be locked.

The following is to set condition of No-Alert calls.

Fields are specified as following:

 Enable or Not: Specify whether enable this condition. If set to Enable, the
accumulated number of failed calls will be used as a condition for system to check.
 Reset When Switching: To clear this condition if other conditions to be met when
you enable two or more Lock/switch card conditions
 USSD Query: Send USSD query command before switching.
 No-Alert calls: Specify the max number of No-Alert calls on this card. If the number
of consecutive No-Alert calls reaches or exceeds this value, the card will be locked if

Shenzhen Ejoin Technology Co., Ltd. 30

www.ejointech.com GSM/CDMA/WCDMA Gateway
this condition is enabled.
 Locking Duration: Specify how long the card will be locked.

The following is to set condition of No-Answer calls.

Fields are specified as following:

 Enable or Not: Specify whether enable this condition. If set to Enable, the
accumulated number of failed calls will be used as a condition for system to check.
 Reset When Switching: To clear this condition if other conditions to be met when
you enable two or more Lock/switch card conditions
 USSD Query: Send USSD query command before switching.
 No-Alert calls: Specify the max number of No-Answer calls on this card. If the
number of consecutive No-Answer calls reaches or exceeds this value, the card will
be locked if this condition is enabled.
 Locking Duration: Specify how long the card will be locked.

The following is to set condition of No Carrier calls.

Fields are specified as following:

 Enable or Not: Specify whether enable this condition. If set to Enable, the
accumulated number of failed calls will be used as a condition for system to check.
 Reset When Switching: To clear this condition if other conditions to be met when
you enable two or more Lock/switch card conditions
 USSD Query: Send USSD query command before switching.
 No-Alert calls: Specify the max number of No Carrier calls on this card. If the
number of consecutive No Carrier calls reaches or exceeds this value, the card will
be locked if this condition is enabled.
 Locking Duration: Specify how long the card will be locked.
Shenzhen Ejoin Technology Co., Ltd. 31
 www.ejointech.com GSM/CDMA/WCDMA Gateway

The following is to set condition of consecutive short calls.

Fields are specified as following:

 Enable or Not: Specify whether enable this condition. If set to Enable, the
accumulated short calls will be used as a condition for system to check.
 Reset When Switching: To clear this condition if other conditions to be met when
you enable two or more Lock/switch card conditions
 USSD Query: Send USSD query command before switching
 Short Duration Calls: Specify the call duration to recognize a short call. Any call
whose duration is less than this value will be regarded as an short call.
 Locking Duration: Specify how long the card will be locked.

4.4.8 Port Inter-Calling

The screenshot below shows the operation mode to set globally for port inter-
calling.

Fields are specified as following:

 Port Inter-Calling: Specify whether enable port inter-calling.
 Min Call Duration: Specify the minimum call duration.
 Max Call Duration: Specify the maximum call duration.

The screenshot below shows the operation mode to set conditions settings of
port inter-calling.

Shenzhen Ejoin Technology Co., Ltd. 32

 www.ejointech.com GSM/CDMA/WCDMA Gateway

Fields are specified as following:

 By Device Online Time: Gateway will start port inter calling by the device online time,
and the time between min interval and max interval.
 Consecutive Failed Calls: Gateway will start port inter calling when reaches the
consecutive failed calls.
 By Consecutive: Gateway will start port inter calling when reaches the consecutive
calls.
 Total Call Duration: Gateway will start port inter calling when reaches the call
duration.

4.4.9 SIM Num Settings

The screenshot below shows the operation mode to get Local Number by USSD

Fields are specified as following:

Shenzhen Ejoin Technology Co., Ltd. 33
 www.ejointech.com GSM/CDMA/WCDMA Gateway
 Using USSD: when enable it, gateway will get the sim number by ussd command
 USSD Command: Specify the ussd command for querying sim number.
 USSD Key Words: to pick the sim number.
 Prefix Translation: change the sim number prefix.

The screenshot below shows the operation mode to set local number manually.

Fields are specified as following:

 Port No: The GoIP Gateway mobile port. Each port contains one or four card slots.
Port No starts from 1 to 16.

 Number A: Specify the number for card A of the port

 Number B: Specify the number for card B of the port
 Number C: Specify the number for card C of the port
 Number D: Specify the number for card D of the port

4.4.10 AT Command

The screenshot below shows the operation mode of command and parameters
to GoIP Gateway.

Shenzhen Ejoin Technology Co., Ltd. 34

 www.ejointech.com GSM/CDMA/WCDMA Gateway

The module here means the GoIP mobile port.

Button Restart is used to restart this module.
Button Stop is used to stop this module.
Button Start is used to start this module.

The screenshot below shows the operation mode of USSD operation to GoIP
Gateway.

Fields are specified as following:

 Select port: Choose some or all port to execute AT or USSD command.

 At Command: You can enter AT command then execute to the port which you select.
 USSD Command: Enter USSD query command.
 Time Interval: Query balance regularly.

4.4.11 Billing Settings

The screenshot below shows the operation mode to set GoIP billing. A smart
billing server for mobile port is embedded in GoIP Gateway.

Shenzhen Ejoin Technology Co., Ltd. 35

www.ejointech.com GSM/CDMA/WCDMA Gateway

Fields are specified as following:

 Billing: Specify whether enable GoIP billing or not. If set to Enabled, system will bill
the outbound calls for the port which has been assigned with billing tariffs.
 USSD Check: Specify whether enable to get balance through USSD check or not.
This field takes effect only when GoIP Billing is set to Enabled.
 Hangup The Call: Specify whether enable hangup the call when balance is ont
enough. When select enable, the call will be hang up immediately when run out of
balance. But when you select disable the call will not be hangup.
 Reset Balance: Specify whether need to reset the balance to intial balance after sim
card is inserted.
 Initial Balance: Special the initial balance for a new card.

The screenshot below shows the operation mode to set Caution Balances,
Invalid Balances and USSD Keyword List. These settings are used for both
getting balance through USSD and billing GoIP calls. The provider ID is detected
by GoIP Gateway automatically. For a new Gateway without any card inserted,
there may be no records in the two lists.

Fields are specified as following:

 Name: Specify the provider name.
 Caution Balances: Specify four balances separated by semi-colon. Each balance

Shenzhen Ejoin Technology Co., Ltd. 36

www.ejointech.com GSM/CDMA/WCDMA Gateway
corresponds to one Keyword from left International Keys to right Other Keys in
Keyword List table. Each caution balance is a threshold for system to get card
balance through USSD if current balance is less than this threshold. However, the
final card balance is based on only one type which is specified by field Billing Type
in the part of Basic Settings.
 Invalid Balances: like Caution Balances, it specifies the threshold for system to
disable the card if current balance is less than this threshold.
 Query Command: Specify the query command
 Balance Keywords: Specify keywords for system to analyze the balance data after
sending USSD command to carrier mobile network.
 Invalid Balance Keywords: Specify the invalid balance keywords
 Invalid SIM keywords: Specify the invalid sim keywords.

The screenshot below shows the operation mode to set billing tariff.

Add New

Click button Add New to expand the data input area to add new data. Fields are
specified as following:

 Data Status: Mark the status of current data record. Option values are
Add/Edit. Value Add means the data is new while value Edit means the data is old.
 Destination Prefix: Specify the destination prefix used to bill call. If this prefix is best
matched with a destination of an outgoing call from the port(s), the corresponding
tariff will be chosen to bill the call. The prefix can be a regular expression. For
example, [2-8] matches any phone number which starts with digit 2 to 8. And [0-9]
matches all phone numbers.
 Tariff: Specify the tariff detail. In the picture,the tariff means 10 value will be deduct
per 60 seconds.

Shenzhen Ejoin Technology Co., Ltd. 37

 www.ejointech.com GSM/CDMA/WCDMA Gateway
Click button Submit on the right to save the new data record.

Edit

All the records are displayed in list. Two operations are provided on the right of
each record. Click Edit to expand the current data record to Data Detail Area
which is above the Data List.
Click button Submit on the right to save the old data record.

Delete

Click Delete on the right of each record to delete the current record. A message
box will be popped for delete confirmation.

Another shortcut button is also provided on the top right of Data List to delete
multiple selected records in batch. A message box will be popped for
confirmation of batch delete.

4.4.12 Call Dur. Control

The screenshot below shows the call duration settings.

Fields are specified as following:

 Total Max Duration: once call duration reach total max duration, gateway will
lock the sim.0 means no limit.
 Daily Max Duration: daily max duration need set the correct time. For
example ,set 60 minutes, the sim has 60 minutes call duration everyday.

The screenshot below shows the call duration statistics.

Shenzhen Ejoin Technology Co., Ltd. 38

 www.ejointech.com GSM/CDMA/WCDMA Gateway

The columns are specified as following:

 Port: The GoIP Gateway mobile port. Each port contains one or four card
slots. Port No starts from 1 to 16.
 Status: it shows the sim status.
 Total Duration: Specify the total duration has used.
 Remain Duration: Specify the remain duration.
 Daily Duration: Specify the daily duration has used.
 Daily Rem Dur.: Specify the daily remain duration.

4.5 Application Settings

Application Settings focus on the business feature. It includes:

 Phone Book
 Dial Plan
 Number Translation
 Inward Black List
 Inward White List
 Local Billing

These sub topics will be introduced separately below.

4.5.1 Phone Book

The screenshot below shows the operation mode to set phone book. Phone
book is a list contains the relationship between destination phone prefix and
gateway information.

Shenzhen Ejoin Technology Co., Ltd. 39

 www.ejointech.com GSM/CDMA/WCDMA Gateway

Add New

Click button Add New to expand the data input area to add new data. Fields
are specified as following:

 Data status: Mark the status of current data record. Option values are
Add/Edit. Value Add means the data is new while value Edit means the data is old.
 Remote Gateway ID: Specify the prefix of destination number for outbound call to
IP.
If a destination is best matched with any prefix in phone book, the destination
call will be routed to the IP gateway specified by Gateway IP and Gateway
Port.
 Gateway IP: The remote gateway IP.
 Gateway Port: The remote gateway port.

Click button Submit on the right to save the new data

record.

Edit

All the phone book records are displayed in list. Two operations are provided on
the right of each record. Click Edit to expand the current data record to Data
Detail Area which is above the Data List.
Click button Submit on the right to save the old data
record.

Delete

Click Delete on the right of each record to delete the current record. A message
box will be popped for delete confirmation.
Shenzhen Ejoin Technology Co., Ltd. 40
 www.ejointech.com GSM/CDMA/WCDMA Gateway

Another shortcut button is also provided on the top right of Data List to
delete multiple selected records in batch. A message box will be popped for
confirmation ofbatch delete.

Note: The operations Add New/Edit/Delete/Batch Delete mentioned in the

following paragraph are almost the same as phone book.

4.5.2 Dial Plan

The screenshot below shows the operation mode to set dial patterns.

Dial pattern is a string which specifies digits and length of the digits of the dialed
number. Generally, the pound sign # is used as the termination of number input
for dialing. However, if patterns are specified and system detects the dialed
number matches any of the patterns, it will stop collecting input and send out the
collected number to dial even though no pound sign is encountered.

The dial pattern string is a normal regular expression, for example:

The pattern 90[1-4] means the dialed number starts with 90 and the last digit is
any of 1/2/3/4. So any of the input 901, 902, 903 or 904 is acceptable.

4.5.3 Number Translation

The screenshot below shows the operation mode to set manipulation for dial
prefix.

Shenzhen Ejoin Technology Co., Ltd. 41

 www.ejointech.com GSM/CDMA/WCDMA Gateway

Fields are specified as following:

 Prefix: The original prefix in phone number.

 Manipulated Prefix: Specify the digits with which the value specified by Prefix
 will be substituted.

Take the value in screenshot as an example, the prefix 9999 in dialed number
will be substituted with 0. That’s to say, if 999988760101 is input to dial, the final
number dialed out is 088760101.
Note: the manipulation is executed after pattern is matched.

4.5.4 Incoming Translation

The screenshot below shows the operation mode to set inward translation.

Shenzhen Ejoin Technology Co., Ltd. 42

 www.ejointech.com GSM/CDMA/WCDMA Gateway

Fields are specified as following:

 Callee Prefix: Specify the callee prefix.
 Digits Stripped: Specify the digits which are stripped.
 Digits Added: Specify the digits which are added.

Take the value in screenshot as an example, the callee ID is 00880xxxxx, we specify

0080 as the callee prefix,strip 4 digits and don’t add digits,when dial
0088016123456789,the gateway will strip 0086 and call 016123456789.

The screenshot below shows the operation mode to set GoIP callerid hidden.

Fields are specified as following:

 Callerid Hidden:Enable or disable callerid hidden.Your carrier must support that
function.
 Dial prefix:Use the dial prefix you set when enable callerid hidden.

4.5.5 Incoming Black List

The screenshot below shows the operation mode to set incoming black list.

Shenzhen Ejoin Technology Co., Ltd. 43

 www.ejointech.com GSM/CDMA/WCDMA Gateway

Fields are specified as following:

 Callee Prefix: Specify the callee prefix of black list.
 Callee Length: Specify the callee length of black list.

Take the value in screenshot as an example, if the callee id likes 016xxxx, and
the length is 12 digits, the call will be rejected by the gateway.

4.5.6 Incoming White List

The screenshot below shows the operation mode to set incoming white list.

Fields are specified as following:

 Callee Prefix: Specify the callee prefix of black list.
 Callee Length: Specify the callee length of black list.

Take the value in screenshot as an example, if the gateway reject the callee id
likes 016xxxx, we set the white list, we can make a 0167xxxxx.

Shenzhen Ejoin Technology Co., Ltd. 44

 www.ejointech.com GSM/CDMA/WCDMA Gateway
4.6 Advanced Settings

Advanced Settings focus on the high level usage of GoIP Gateway. It includes:
 Network
 Voice and Codec
 Other Settings

These sub topics will be introduced separately below.

4.6.1 Network

The screenshot below shows the operation mode to set VPN settings, and the
protocol of vpn is pptp.

Fields are specified as following:

 VPN Support: Whether support vpn or not.
 Server Address: Specify the vpn server address.
 Usename: Specify the username of vpn.
 Password: Specify the password of vpn.
 Local IP: The VPN client ip.
 Remote IP: The VPN remote ip

The default port of web server is 80. The field Web Port is used to set another
different port for web server. For example, if field Web Port is set to 8080 and
wan IP is 192.168.1.67, the web pages then should be accessed through URL:
http://192.168.1.67:8080/ from this computer.

The field Telnet Port is used to change the default port of telnet service.

Shenzhen Ejoin Technology Co., Ltd. 45

 www.ejointech.com GSM/CDMA/WCDMA Gateway
4.6.2 Voice and Codec

The screenshot below shows the operation mode to set voice settings.

Voice Volume is used to specify the input voice volume, output voice volume and

DTMF tone volume. The acceptable value for volume is an integer no less than

10 and no greater than 40.

The Dial Tone is sent to a customer or operator to indicate that the receiving end
is ready to receive dial pulses or DTMF signals. It is used in all types of dial
offices when the customer’s or operator’s dials produce dial pulses.

A Ring Back tone (or ringing tone) is an audible indication that is heard on the
telephone line by the caller while the phone they are calling is being rung. It is
normally a repeated tone, designed to assure the calling party that the called
party's line is ringing.

The Busy Tone indicates that the called customer’s line has been reached but
that it is busy, being wrong, or on permanent signal. W hen an operator applies a
busy signal, it is sometimes called a busy-back tone. Line Busy Tone is a Low
Tone that is on and off every 0.5 second.

The settings of Dial Tone, Ring Back Tone and Busy Tone depend on area. The
default settings for Asia are shown in the screenshot above for reference.

Shenzhen Ejoin Technology Co., Ltd. 46

 www.ejointech.com GSM/CDMA/WCDMA Gateway

The screenshot below shows the operation mode to set codec priority.

Three codec types are provided to adjust GoIP Gateway to different network
environment. It support G729a/b/e,G723.1,G711A/U law,iLBC,AMR auto-
selecting.

4.6.3 other settings

The screenshot below shows the operation mode to set analog port attribute.

The columns are specified as following:

 Port: The GoIP Gateway mobile port. Each port contains one or four card slots. Port
No. starts from 1 to 16.
 Type: Values are GSM/CDMA. (According to your module.)
 Disable: Specify whether enable or disable this port.
 Hot-line: Specify a sip phone on the softswitch to pick up the incoming calls..

Shenzhen Ejoin Technology Co., Ltd. 47
www.ejointech.com GSM/CDMA/WCDMA Gateway
 UnconditionalForward/NoAnserForwardNumber/BusyForward: These parameters
are designed to be used with a third party system.

The screenshot below shows the operation mode to set application feature

The fields are specified as following:

 Caller ID Display: Specify whether enable Caller ID Display or not.
 Silence Suppression: Specify whether enable Silence Suppression or not.
 Adaptive Jitter Buffer: Specify whether enable Jitter Buffer or not.
 IP TOS: Specify whether enable IP TOS or not.
 Don’t send # to PSTN: Specify whether need to remove the last digit # to PSTN if
the last digit of numbers is #. If set to Enable, the last # will be removed.
 Append # to PSTN: Specify whether need to send an extra # to PSTN after the
normal digital numbers are sent.
 Carry PSTN Caller ID: Specify whether need to carry PSTN caller ID to system.
 Forbid GSM Call: Specify whether need to prevent the PSTN incoming call. If set to
enable, any of the incoming calls whose callerid is not in the white list specified in
White Number List will be prevented.
 White Number List: Specify a caller number list separated by comma. It is used in
combination with Forbid GSM Call to let the specified caller pass through and
continue the incoming call flow if Forbid GSM Call is set to Enable.

Shenzhen Ejoin Technology Co., Ltd. 48

 www.ejointech.com GSM/CDMA/WCDMA Gateway
 DTMF Pre-Act Time: Specify the DTMF Pre-Act Time.
 DTMF Activity Time: Specify the DTMF activity time.
 Max Alerting Time: Specify the max alerting duration.
 Max Ringback Time: Specify the max ringback duration.
 Max Call Duration: Specify the max call duration. System will hang up the call
automatically if the call duration reaches this value.
 RTP Inactivity Time: Specify the max duration of silence from gateway. System will
hang up the call automatically if the silence duration reaches or exceeds this value.
 GSM Call AutoAnswer: Specify whether need to auto-answer the call which is from
GSM. If set to Enable, AutoAnswer Time can be used to specify the delay to
automatically answer the incoming GSM call.
 VoIP Call AutoAnswer: Specify whether need to auto-answer the call which is from
IP network. If set to Enable, AutoAnswer Time can be used to specify the delay to
automatically answer the incoming IP call.
 DTMF Mode: Specify the DTMF mode Option values are RFC2833/Inband/SIP
INFO.
 RFC2833 Payload Type: Specify the RFC2833 DTMF Payload Type. Only valid
when DTMF Mode is set to RFC2833. The default value is 101.
 RTP Ptime: Specify the interval of RTP packages.
 RTP Start Port: Specify the RTP start port.

4.7 System Settings

System Settings include:

 User Mgmt
 Device Mgmt
 System Update

These sub topics will be introduced separately below.

4.7.1 User Mgmt

The screenshot below shows the operation mode to manage system user.

Shenzhen Ejoin Technology Co., Ltd. 49

 www.ejointech.com GSM/CDMA/WCDMA Gateway

Default User

The default system user account is root. This account can’t be deleted and only

Password and Privilege can be modified for this account.

Add User

Click button Add New to expand the data input area to add new data. Fields
are specified as following:

 Data status: Mark the status of current data record. Option values are
Add/Edit. Value Add means the data is new while value Edit means the data is old.
 Account: The user account used to login web system. The account value can not
be modified after save.
 Password: The password used to login web system.
 Privilege: The privilege of user. Option values are Admin/User.
Click button Submit on the right to save the new data record.

Edit User

All the user records are displayed in list. Two operations are provided on
the right of each record. Click Edit to expand the current data record to Data
Detail Area which is above the Data List.
Click button Submit on the right to save the old data record.

Delete User
Shenzhen Ejoin Technology Co., Ltd. 50
 www.ejointech.com GSM/CDMA/WCDMA Gateway
Click Delete on the right of each record to delete the current record. A
message box will be popped for delete confirmation.

Another shortcut button is also provided on the top right of Data List to delete
multiple selected records in batch. A message box will be popped for
confirmation of batch delete.

4.7.2 Device Mgmt

The screenshot below shows the operation mode to set basic settings.

Fields are specified as following:

 Device Alias: Specify the device alias.
 Auto Reboot: Specify the auto reboot time.
 Scheduled Reboot: Specify the scheduled reboot time.
The screenshot below shows the operation of date and time settings.

The default time zone is UTC+8, you can change the time zone as your country. For
example, Bangladesh is UTC+6, and change as +6. If your device is not touch with the
internet and want to get accurate time, the time server will help.

The screenshot below shows the operation mode for remote management.

Shenzhen Ejoin Technology Co., Ltd. 51

 www.ejointech.com GSM/CDMA/WCDMA Gateway
Remote Management is used to manage the GoIP Gateways located in other
physical locations. Network must be available for the gateway to communicate
with ERM Server.

If ERM is enabled and correctly set, the GoIP will register to ERM server and set
up the connection between itself and ERM server. Administrator can login ERM
server and monitor all the registered GoIP Gateways. Commands can also be
sent from ETMS server to certain gateway for management.

The configuration fields are specified as following:

 Enable ERM: Specify whether enable ETMS registration or not. Option values are
Enabled/Disabled.

 ERM Server IP: Specify the ERM Server address.

 ERM Server Port: Specify the ERM server port.
 Account: Specify the account which create in the ERM.
 Password: Specify the password which create in the ERM.
 Status: Specify the registration status.

4.7.3 File Management

The screenshot below shows file list. This is gdb file for checking the software bug.

 Seq.: sequence of gdb file.

 Filename: the name of gdb file.
 Modification Time: the time of gdb file generate.
 Type: Specify the type.
 Operations: the operation of gdb, delete or export.

4.7.4 System Update

The screenshot below shows the operation mode for system update or restore.

Shenzhen Ejoin Technology Co., Ltd. 52

 www.ejointech.com GSM/CDMA/WCDMA Gateway

System Update

The content for system update includes:

 firmware
 configuration
 ramfs
 kernel
 uboot
 debug tools
 voice prompt
 voice cfg
 mac file
 lic file

The configuration fields are specified as following:

 File Type: Specify the content to update. Option values are listed above.
 File Name: Specify the content file name. Click button Browser and then select
the target file from the popped file selection window.

Export Configuration

Click ‘Export’ button to export the configuration

Restore To Factory

System restore is used to restore the system to default settings. A message

box will be popped for the confirmation of restore.

Shenzhen Ejoin Technology Co., Ltd. 53

 www.ejointech.com GSM/CDMA/WCDMA Gateway
4.8 Debugging Tools

4.8.1 Test Network

The screenshot below shows the auto ping settings

Fields are specified as following:

 Auto Ping: Specify whether enable auto ping.
 IP Address: Specify the ip address.
 Packet Size: Specify the packet size.
 Duration: Specify the ping duration
 Normal Loss Rate: Specify the normal loss rate.

The screenshot below shows the manual ping settings

Fields are specified as following:

 IP Address: Specify the ip address.
 Packet Size: Specify the packet size.
 Packet Count: Specify the packet count.

Shenzhen Ejoin Technology Co., Ltd. 54

 www.ejointech.com GSM/CDMA/WCDMA Gateway
4.9 Running Status

Running Status includes:

 Port Status
 Call Status
 System Status
 Call Statistics
 Inter-Call Stats
It is used to monitor real-time situation for calls, GSM ports and equipment
hardware status.

4.9.1 Port Status

The screenshot below shows the SIP Client Status.

The screenshot below shows the GoIP Gateway port LED status. Different LED

color stands for different port status.

Note:
LED A/B/C/D displays in accordance with the lights on the front board of GoIP
Gateway. Port 1 to 16 relate to the physical port of GoIP Gateway. The following
table shows the relationship between LED color and port status.

Shenzhen Ejoin Technology Co., Ltd. 55

 www.ejointech.com GSM/CDMA/WCDMA Gateway
The screenshot below shows the GOIP Port Balance.

The screenshot below shows the port status in detail.

The status columns are specified as following:

 Port No: The physical port sequence from 1 to 16.
 Module Detected: Specify whether port module has been detected or not.
 Option values are Yes/No.
 SIM Registered: Specify whether SIM is registered or not. Option values are
 Yes/No.
 Provider: The mobile provider that system detects.
 Signal Strength: Specify the mobile signal strength.
 SMS Count: Shows how many SMS has been sent since the last start up of system.

Shenzhen Ejoin Technology Co., Ltd. 56

 www.ejointech.com GSM/CDMA/WCDMA Gateway
4.9.2 Call Status

The screenshot below shows the live call status.

The status columns are specified as following:

 Port No: The physical port sequence from 1 to 16.
 Type: GSM of CDMA Currently GoIP is regarded as GSM.
 State: Specify the call status.
 Duration: Specify the call duration
 Balance: Specify the current balance of the card in this port.
 Description: Specify the card status.

4.9.3 System Status

The screenshot below shows the system status. It includes WAN status, LAN
status and others. The reported information can help you get the system status
detail in a fast, simple way.

Shenzhen Ejoin Technology Co., Ltd. 57

 www.ejointech.com GSM/CDMA/WCDMA Gateway

4.9.4 Call Statistics

The screenshot below shows the call statistics information for analysis.

The status columns are specified as following:

Shenzhen Ejoin Technology Co., Ltd. 58

 www.ejointech.com GSM/CDMA/WCDMA Gateway
 Port No: The physical port sequence from 1 to 16.
 Calls: Specify the total calls made out from this port since the last start up of system.
 Alerted: Specify the total number of responded alerting message for all the calls
made.
 Connected: Specify the total number of answer from destination for all the calls
made.
 Consecutive Fails: Specify the consecutive fail calls.
 No Carriers: Specify the no carrier.
 PDD: Specify the average duration to receive the response of alerting message.
 ACD: Specify the average duration of talking between caller and callee.
 ASR: Specify the percentage of successful call for which there is a responded
alerting messaged returned.

A total summary is displayed at the bottom of the table.

4.9.5 Inter-call Stats

The status columns are specified as following:

 Port No: The physical port sequence from 1 to 16.
 State: Specify the call status.

Shenzhen Ejoin Technology Co., Ltd. 59

www.ejointech.com GSM/CDMA/WCDMA Gateway
 Duration: Specify the call duration.
 Incoming calls: Specify the total incoming calls since the last start up of inter calling
system.
 Outgoing Calls: Specify the total outgoing calls since the last start up of the inter
calling system.
 Descriptions: Specify the card status.

4.10 Save and Reboot

Generally, any modification should require the reboot of GoIP Gateway to bring
the modification into effect . However, single Save without
R e b o o t i s a l s o frequently used to save the modifications which will be
effective on next reboot of GoIP Gateway.

The screenshot above shows the operation buttons. Button Save is used to save
all the modifications while button reboot is used to save modifications first and
then reboot device immediately.

Shenzhen Ejoin Technology Co., Ltd. 60

 www.ejointech.com GSM/CDMA/WCDMA Gateway

5 Typical Used Scenario

This chapter presents some typical used scenarios for reference.

5.1 Landing from IP to Mobile Network

GoIP Gateway is now used more and more for telephone carriers to land their IP
calls to mobile network. It plays the role of converting IP telephone signal to
GSM telephone signal, relaying the media stream b et we e n IP network
and Mobile network.

GoIP Gateway can be placed either in the LAN of Softswitch server or in public
network environment which can be accessed by Softswitch server through public
IP in different physical location.

Shenzhen Ejoin Technology Co., Ltd. 61

www.ejointech.com GSM/CDMA/WCDMA Gateway

5.2 Access from Mobile Network to IP

GoIP Gateway can be used as the access from mobile network to IP. Any call
made to the mobile card inserted into GoIP Gateway will be routed to IP network
and connected to Softswitch server. The Softswitch server can redirect the caller
to final destination user.

Shenzhen Ejoin Technology Co., Ltd. 62