DESCRIPTION The UTC NE555 is a highly stable timer integrated circuit. It can be operated in both Astable and Monostable mode. With monostable operation, the time delay is precisely controlled by one external and one capacitor. With a stable operation as an oscillator the frequency and duty cycle are both accurately controlled with two external resistors and one capacitor.
FEATURES *High current driver capability(=200mA). *Adjustable duty cycle. *Timing from μs to hours. *Turn off time less than 2μs. *Operates in both astable and monostable modes.
ORDERING INFORMATION Ordering Number Package Packing Normal Lead Free Halogen Free NE555-D08-T NE555L-D08-T NE555G-D08-T DIP-8 Tube NE555-S08-R NE555L-S08-R NE555G-S08-R SOP-8 Tape Reel NE555-S08-T NE555L-S08-T NE555G-S08-T SOP-8 Tube
NE555 LINEAR INTEGRATED CIRCUIT PIN CONFIGURATION
UNISONIC TECHNOLOGIES CO., LTD 2 of 8
www.unisonic.com.tw QW-R106-001,F NE555 LINEAR INTEGRATED CIRCUIT BLOCK DIAGRAM
UNISONIC TECHNOLOGIES CO., LTD 3 of 8
www.unisonic.com.tw QW-R106-001,F NE555 LINEAR INTEGRATED CIRCUIT ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL RATINGS UNIT Supply Voltage VCC 16 V Power Dissipation PD 600 mW Junction Temperature TJ +125 ℃ Operating Temperature TOPR -20 ~ +85 ℃ Storage Temperature TSTG -40 ~ +150 ℃ Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. ELECTRICAL CHARACTERISTICS (VCC=5 ~ 15V, Ta=25℃, unless otherwise specified.) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Supply Voltage VCC 4.5 16 V VCC=5V, RL=∝ 3 6 mA Supply Current (Note 1) ICC VCC=15V, RL=∝ 7.5 15 mA Monostable 1.0 3.0 % Initial Accurary (Note 2) ACCUR RA=1k ~ 100kΩ Astable 2.25 % Monostable 50 ppm/°C Drift with Temperature Δt/ΔT C=0.1μF Astable 150 ppm/°C Monostable 0.1 0.5 %/V Drift with Supply Voltage Δt/ΔVCC Astable 0.3 %/V VCC=15V 9.0 10.0 11.0 V Control Voltage VC VCC=5V 2.6 3.33 4.0 V VCC=15V 10.0 V Threshold Voltage VTH VCC=5V 3.33 V Threshold Current(Note 3) ITH 0.1 0.25 μA VCC=5V 1.1 1.67 2.2 V Trigger Voltage VTR VCC=15V 4.5 5 5.6 V Trigger Current ITR VTR=0 0.01 2.0 μA Reset Voltage VRST 0.4 0.7 1.0 V Reset Current IRST 0.1 0.4 mA VCC=15V ISINK=10mA 0.06 0.25 V Low Output Voltage VOL ISINK=50mA 0.3 0.75 V VCC=5V ISINK=5mA 0.05 0.35 V VCC=15V ISOURCE=200mA 12.5 V High Output Voltage VOH ISOURCE=100mA 12.75 13.3 V VCC=5V, ISOURCE=100mA 2.75 3.3 V Rise Time of Output tR 100 ns Fall Time of Output tF 100 ns Discharge Leakage Current ILKG 20 100 nA Note 1: Supply current when output high typically 1mA less at VCC=5V. Note 2: Tested at VCC=5.0V and VCC=15V. Note 3: This will determine the maximum value of RA+RB for 15V operation, The maximum total is R=20MΩ, and for 5V operation the maximum total is R=6.7MΩ.
UNISONIC TECHNOLOGIES CO., LTD 4 of 8
www.unisonic.com.tw QW-R106-001,F NE555 LINEAR INTEGRATED CIRCUIT TYPICAL APPLICATION CIRCUIT
www.unisonic.com.tw QW-R106-001,F NE555 LINEAR INTEGRATED CIRCUIT TYPICAL APPLICATION NOTES The application circuit shows astable mode configuration. Pin 6 (Threshold ) is tied to Pin 2 ( Trigger ) and Pin 4 ( reset ) is tied to VCC ( Pin 8 ). The external capacitor C1 of Pin 6 and Pin 2 charges through RA, RB and dischages through RB only. In the internal circuit of UTC NE555 , one input of the upper comparator is at voltage of 2/3Vcc(R1=R2=R3),another input is connected to Pin 6.As soon as C1 is charging to higher than 2/3Vcc, transistor Q1 is turned ON and discharge C1 to collector voltage of transistor Q1. Therefore, the flip-flop circuit is reset and output is low. One input of lower comparator is at voltage of 1/3Vcc, discharge transistor Q1 turn off and C1 charges through RA and RB. Therefore, the flip-flop circuit is set output high. That is, when C1 charges through RA and RB , output is high and when C1 discharge through RB ,output is low. The charge time(output is high) t1 is 0.693(RA+RB) C1 and the discharge time (output is low) T2 is 0.693 RB*C1. ⎛ 1 ⎞ ⎜ Vcc − Vcc ⎟ ln⎜ 3 ⎟ = 0.693 ⎜ Vcc − 2 Vcc ⎟ ⎝ 3 ⎠ T1=0.693*(RA+RB)*C1 Thus the total period time T is given by T2=0.693*RB*C1 T=T1+T2=0.693(RA+2RB)*C1.
Then the frequency of astable mode is given by
1 1.44 f = = T (RA + 2RB) * C1 The duty cycle is given by T2 RB D.C. = = T RA + 2RB .
UNISONIC TECHNOLOGIES CO., LTD 6 of 8
www.unisonic.com.tw QW-R106-001,F NE555 LINEAR INTEGRATED CIRCUIT TYPICAL CHARACTERISTICS Voltage Drop,(VCC-VOH) (V)
Supply Current,ICC (mA)
Low-Level Output Voltage vs Low-Level Output Voltage vs Low-Level Output Current Low-Level Output Current 10 10 7 VCC=5V 7 VCC=10V Low-Level Output Voltage,VOL (V)
www.unisonic.com.tw QW-R106-001,F NE555 LINEAR INTEGRATED CIRCUIT
UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice.
