Scribd
Upload
178 views2 pages

2202A

The JBL 2202 is a highly efficient low frequency loudspeaker capable of producing 100 watts of continuous program power. It has a 4" edgewound copper ribbon voice coil and a frequency response from 60-4000 Hz. Its powerful magnet structure and rugged cone assembly enable it to achieve high sensitivity and smooth output.

Uploaded by

Ivica Indjin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
178 views2 pages

2202A

The JBL 2202 is a highly efficient low frequency loudspeaker capable of producing 100 watts of continuous program power. It has a 4" edgewound copper ribbon voice coil and a frequency response from 60-4000 Hz. Its powerful magnet structure and rugged cone assembly enable it to achieve high sensitivity and smooth output.

Uploaded by

Ivica Indjin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

100 Watts continuous program

4” edgewound copper ribbon voice coil


60-4000 Hz resj~onse
47 dB sensitivity

The 2202 is a highly efflclent, low frequency loudspeaker The 2202 has a low-loss magnetic structure that weighs 13
Compared to other loudspeakers having similar sensitivity. pounds, consisting of a large Alnico V magnet and top
its frequency response is unusually linear, varying only *2 dB plate, pole piece and magnetic return casting made from a
from 120 Hz to 3 kHz The 2202’s performance characteristics high-conductiwty iron alloy. Each component IS precisely
make it well suited for use is a small stage monitor machined to concentrate a maximum amount of magnetic
loudspeaker, as a mldrange driver in wide range sound energy in the voice coil gap.
reInforcemen systems or as a low frequency driver in
The combination of this powerful magnetic structure, a
installations where mounting space IS restricted.
rugged cone assembly and 4.Inch diameter edgewound
A tough, double roll compliance is featured which increases copper ribbon voice coil enable the 2202 to achieve its
power handling capacity and reliability. This unique cone loo-watt continuous program power capacity. exceptional
termmatlon IS completely passive so that during sustained sensltlvity and smooth acoustic output.
high power Inputs. sound quality iema~ns wtually unchanged
The cone, voice co11 and spider are assembled with a heat
resxtant. arcraft-grade epoxy-specially formulated for
- JBL -resulttng in an exceptionally strong bond and greater
structural mtegrlty than is possible with other commonly used
adheswes.
Model 2202-12” Low Frequency Loudspeaker

Architectural Specifications

The transducer shall have a nomlnal diameter of 12 Inches.


overall depth not greater than 4% Inches and weigh at least
15 pounds. The frame shall be cast aluminum. An Almco V
magnet shall be contained withIn a cast ~nzn magnetic return
circuit for maximum efflclency and suppression of stray fields.
The vace co11 shall have a nommal diameter of 4 inches, be
made of edgewound copper ribbon wire and operate in a
magnetic field of not less than 12,000 gauss.

Measured sens~tiwty (SPL at 30 feet with a I-mW input.


warbled 500 to 3000 Hz) shall be at least 47 dB on-axis and
45 dB 45 degrees off-axls. As an Indication of
electromechanical conversion efficiency, the BI factor shall
be at least 2 2x 10’ dynes per abampere. On-axis frequency
response measured at a distance of SIX feet or nvxe in a
free-field environment shall extend from 120 to 3000 Hz
*2 dB and usable frequency response shall extend from
60to 4000 Hz. Nomlnal Impedance shall be 8 ohms.

The loudspeaker shall be capable of withstandIng a power


input of 100 Watts continuous program or a 50-Watt RMS
sIgnal which is warbled at all frequencies within one-half
octave above and below the frequency at which m~n~murn
Impedance occurs and sustatn this performance for a
nxn~mum of one hour without damage.

The transducer shall be JBL Model 2202.

You might also like