Garlic Peeler

Model DAL06
Instruction Manual

Version 1

3115 Pepper Mill Court, Mississauga, ON, L5L 4X5 1-800-465-0234

4450 Witmer Industrial Estates, Unit 4, Niagara Falls, NY, 14305 www.omcan.com
Table of Contents
Model DAL06

Section Page

General Information -------------------------------------------------------------------------------- 3

Safety and Warranty --------------------------------------------------------------------------- 3 - 4

Technical Specifications ---------------------------------------------------------------------- 4 - 5

Installation -------------------------------------------------------------------------------------------- 5

Operation --------------------------------------------------------------------------------------------- 6

Maintenance ----------------------------------------------------------------------------------------- 7

Parts Breakdowns ---------------------------------------------------------------------------- 8 - 10

Electrical Schematics ---------------------------------------------------------------------------- 11

Warranty Registration ---------------------------------------------------------------------------- 13

2
 General Information
Omcan Manufacturing and Distributing Company Inc. and Food Machinery Of America, Inc. dba Omcan
are not responsible for any harm or injury caused due to any person’s improper or negligent use of
this equipment. The product shall only be operated by someone over the age of 18, of sound mind, and
not under the influence of any drugs or alcohol, who has been trained in the correct operation of this
machine, and is wearing authorized, proper safety clothing. Any modification to the machine voids any
warranty, and may cause harm to individuals using the machine or in the vicinity of the machine while
in operation.

The DAL06 garlic peeler is designed to peel food products safely and efficiently. Unless the operator is
properly trained and supervised, there is the possibility of a serious injury. It is the responsibility of the owner to
ensure that this machine is used properly and in a safe manner. It is mandatory to strictly follow the instructions
contained in this manual and any requirements of local law.

Safety and Warranty

The DAL06 must be used and handled with care.
• BEFORE cleaning always disconnect the unit from the power supply.
• NEVER use tools not intended to assist the unit in operation.
• NEVER lift the lid before being sure the plate (Pic. 1, #6) is has completely stopped.
• The plate must be properly fitted onto the central shaft pin (Pic. 2, #2).
• BE CAREFUL when handling the plate. It is heavy and can cause injury if dropped.
• DO NOT put your hands inside the unit during operation.
• NEVER connect the power source with wet hands or clothes.
• NEVER spray water or other liquid substances directly at the motor, power switch or any other electrical
components.
• ALWAYS install equipment in a working area with adequate light and space away from children and other
objects.
• NEVER operate without all warning labels attached and manual available to the operator.
• NEVER leave unattended while operating.
• ALWAYS ground the unit properly.
• DO NOT process frozen foods or other products other than garlic.
• ALWAYS turn the unit off and disconnect the power cord before cleaning and maintenance.
• PROVIDE enough space around the unit for easy operation.
• ALWAYS keep the floor dry. Wet floors may cause injury.
• ALWAYS turn the unit off in the case of electrical problems.
• NEVER let dust or water get into electrical mechanical components of the unit.
• DO NOT modify original features of the unit.
• DO NOT take out nor tear off any safety or identification labels.
• DO NOT wear loose clothing when operating the unit. Do not wear jewelry or bracelets and roll up loose
sleeves.
• ALWAYS tie back hair.

3
Safety and Warranty
1 YEAR WARRANTY

WARNING:

The packaging components are classified as normal solid urban waste and can therefore be disposed of
without difficulty.

In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.

DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

Technical Specifications

PICTURE 1

MAIN COMPONENTS

1. Water Inlet.
2. ON/OFF Switch.
3. Base.
4. Lid.
5. Outlet Waste.
6. Disc.

4
 Technical Specifications
Technical Data Units DAL06
Voltage V 110
Frequency Hz 60
Rating HP 0.25
Consumption Kw/h 0.18
Height mm 545
Width mm 340
Depth mm 350
Net Weight kg 17.0
Gross Weight kg 19.0
Bowl Capacity kg 4
Estimated Time min 8

Installation
The DAL06 must be installed on a flat, non-skid work surface. During peeling operation, the food product
must be wet by means of 3/4” inlet pipe (Pic. 1, #1). An alternative is to place the machine below a 3/4” water
faucet and let the water flow during the operation. It is recommended to place the machine near a sink to allow
wastes to flow out. A drainage pipe may be connected to outlet waste (Pic. 1, #5) to flow the wastes out to the
nearest sink.

5
Operation
PRE-OPERATION

Check the voltage of the machine. The voltage of the unit must correspond with the power supply. Make sure
the unit is properly grounded. Make sure the machine is in a stable position. The water inlet pipe and drainage
pipe must be installed properly as indicated below (Pic. 3).
Picture 3

IMPORTANT: BE SURE THE PLATE IS FIRMLY FITTED ONTO THE CENTRAL SHAFT
PIN.

First, check if the lid (Pic. 1, #4) is properly fitted on the top of the unit. To start the machine, toggle the switch
(Pic. 1, #2) to the ON position. Let the water flow into the chamber and load it with food product. Water will then
flow out through the waste outlet. Each load shall not exceed 4 kg. The peeling time is 8 minutes, however
depending on the hardness of the food product, size and irregularity, the time may vary. Check if products
are peeled looking through the opening of the top lid. Remove the peeled product from inside the chamber
manually after closing the faucet, turning the machine off and disconnecting it from the power supply.

IMPORTANT: UNDER NO CIRCUMSTANCES SHOULD YOU PUT YOUR HANDS IN

THE MACHINE DURING OPERATION. BE SURE THAT THE UNIT HAS COMPLETELY
STOPPED BEFORE REMOVING THE PROCESSED GARLIC.

6
 Maintenance
IMPORTANT

1. Turn the machine OFF and disconnect it from power source.

2. Wait until the plate is completely still.
3. To lift the plate out of the cylinder, pull it upwards.
4. Wash the machine and the plate with water and neutral soap.
5. To reassemble the parts by reversing the procedure.

For fast cleaning, turn the machine ON without product inside and let it work with running water.

ATTENTION

Always unplug the machine before cleaning or maintenance.

7
Parts Breakdown
Model DAL06 10865

8
 Parts Breakdown
Model DAL06 10865

Complete Motor Support C1

Complete Base A1

Complete Motor Kit D1

Complete Cabinet B1

Complete Disc E1

9
Parts Breakdown
Model DAL06 10865

Item Item Item

Description Position Description Position Description Position
No. No. No.
30343 Cabinet Lid 1 30275 Screw 6x20 23 30372 Cabinet B2
30194 Reduction Bush 2 30258 Washer L 5/16 ZB 24 30328 Peeler Base B4
24020 Reduction Set 3 30321 Moved Pulley 25 16404 Peeler Feet B5
30313 Movement Sheet 4 30201 Ball Bearing 6202 26 19749 Complete Motor Support C1
16419 Washer L.A6 4 125 Inox 5 Attention Label 27 30388 Complete Motor 0.25HP 60Hz D1
30330 Screw M6x12 DIN 933 S/S 6 30259 Clamp K22 T-50R 28 18949 Select Switch D2
ID Motor Label 7 30305 Cable 3x1.0mm with Plug 29 20016 Disc with Rubber Bumpers E1
30249 ON/OFF Switch 8 38208 Wire Passer Molde 0922231 30 38103 Rubber Fin E2
30364 Omcan Logo 9 16394 Switch 14123 - A1B1E3Q 31 38104 Fully Grey Disc E3
30191 Rubber Retainer 5206 10 30050 Terminal Cover 32 38105 Screw for Rubber Fin E4
Machine Sleeve 75mm
30254 11 Pressure Rivet AD-440-S 30317 Screw 1/4 x 1/4 X1
Diameter
30218 Extension 75mm Diameter 12 30030 Positive Terminal Lock 0 5 A1 5 33 30215 Switch HH-201 X2
30293 Outlet Pipe 75mm 13 27692 Insulating Terminal EF-4228 34 30281 Screw M6x12 DIN 933 X3
30331 Elastic Pin 6x40 14 30350 Nylon Cover CN-4472 35 30236 Washer L.A6 4 X4
30306 Central Shaft 15 30303 Protection Sheet 36 30185 Electrical Cable Switch X5
Enclosed Terminal Tube
Screw 1/4 x 3/8 16 30029 Pressure Rivet AD-423-S 37 30181 X6
1/4x20mm
30288 Driving Pulley 17 38102 Motor 0.25HP 60Hz 38 30384 Motor 0.25HP 60Hz X7
30230 Belt 1160 18 30377 Complete Base A1 30058 Cable 3x0.75mm2 X8
27686 PFS UNC 1/4 x 3/4 RTZB 19 30207 Retainer 00726BR A2 30059 Omcan Logo X9
30222 Washer 78x7x20x25mm 20 30374 Base A3 30389 Complete Motor 0.25HP 60Hz X10

30234 Washer L 1/4 x 1 6ZB 21 30212 Ball Bearing 6203 A4 30375 Washer L.A21 DIN 125 Inox X11

30332 Motor Support 22 30401 Complete Cabinet B1

10
 Electrical Schematics
Model DAL06 10865

11
12
 Warranty Registration

Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at
the perforation and then send to the address specified below. You can also register online by visiting:
www.omcan.com/warrantyregistration.html

For mailing in Canada For mailing in the US

OMCAN INC. OMCAN

PRODUCT WARRANTY REGISTRATION PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court, 1889 Maryland Avenue,
Mississauga, Ontario Niagara Falls, New York
Canada, L5L 4X5 USA, 14305


Purchaser’s Information
Name: Company Name:
Address:
Telephone:
City: Province or State: Postal or Zip: Email Address:
Country: Type of Company:
Restaurant Bakery Deli
Dealer from which Purchased: Butcher Supermarket Caterer
Dealer City: Dealer Province or State: Institution (specify):
Invoice: Other (specify):

Model Name: Model Number: Serial Number:

Machine Description:
Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):

Thank you for choosing Omcan

13
Over the last 60 years, Omcan has grown to become a leading supplier to the food
service industry in Canada and the USA. Our success over these many years is
directly attributed to our established relationships with all of our valued customers
and through providing them with Diverse, Dependable and Proven products.
Omcan continues to help our customers remain competitive.

With associates in North America, Europe, and Asia, our global footprint continues
to expand as we hold to the principle that clients benefit from the accessibility
and familiarity of our sales team. In 2013 as our geography and brand recognition
continued to grow, we changed to one name Omcan Food Machinery.

In over 200,000 sq ft of warehouse space we stock over 2,500 quality food

equipment and supplies for the food preparation market.