.

Proceedings of The South African Sugar Technologists' Association - June 1994

A REVIEW OF CANE KNIFING

MJ REID
Sugar Milling Research Institute, Durban

Abstract No mills have all four types of cane knife together, as

discussed below.
The role of the knives in cane preparation is discussed
and the few later developments which have taken place in
South African mills are enumerated. Typical installations
presently in existence are described and the average power Survey of cane knife installations
provided per ton of fibre processed is given. Various types There are 24 cane preparation lines in South Africa and
of cane knives which have become available are briefly in- Swaziland. There is not enough information on those in
troduced and their relative merits are evaluated. Some of Zimbabwe and Malawi to be included in this brief survey
the earlier work on the comparison of hard facing materials which is taken from an SMRI communication (Reid, 1992).
is described and some recommendations are given. Twelve lines have three sets of knives. In most of these
cases the first knife is a leveller and does little preparation.
In nine of these lines the third knife is a shredder feed knife.
Introduction It may therefore be concluded that most knifing is effectively
carried out by one knife set, which may be called the "main"
The increasing use of diffusers in Southern Africa has knife. In fourteen lines the main knife runs in "reverse"
placed more emphasis on the importance of shredder prep- direction to the conventional. This means that it cuts up-
aration to achieve good percolation, and the role of the cane wards into the advancing cane blanket, and usually cuts
knife has tended to be pushed into the background. This is against a fixed or rotating anvil, throwing the cane down
understandable because it has become apparent that coarse onto the next conveyor in a shallow trajectory.
knifing and fine shredding are beneficial to good percolation
whereas the converse could cause serious flooding in the Each of the lines at Felixton has two "billeters", one each
diffuser. The role of the cane knife has therefore become that for rail and road deliveries which are 20 and 14 m wide
of a device to ensure that the shredder is evenly fed and that respectively. These were designed to chop the cane into short
no conditions exist that can promote choking. billets to facilitate conveying on a rubber belt and feeding
at a controlled rate into the shredder. The original idea was
based on slow speed cutting of evenly presented cane with
a sharp knife but the shape of knife and design of its at-
The role of the cane knife tachment were no match for the high sand, rock and tramp
Before the advent of the shredder, the cane knife was the iron content of FX cane. After much experimentation the
only means of preparation, and was perfectly adequate when attachment has been modified so that the knife pivots on a
the acceptable extraction was around 90%. However, when polyurethane bush and the knife shape has been changed to
higher extraction became more important it was realised that put a more even load on the attachment. The material of
a greater proportion ofbroken cells could be more effectively the knife is now a cast alloy which is refurbished by abrasive
achieved by hitting the cane with a heavy hammer at very sharpening several times per season.
high speed and in the process employing greater power. The The first of the objectives of the billeters has been achieved
cane knife was then relegated to the role of leveller or pre- but not as effectively as was intended. The billetted cane is
breaker in order to facilitate the operation of the shredder. -not cut into neat short lengths like chopper harvested cane
In fact more engineers are beginning to hold the opinion
that a large shredder on its own without any previous knifing
is better than one or more cane knives followed by a shred-
der. Of course this would only work satisfactorily if the in-
coming cane was either very clean and uniform, such as in
the case of burnt cane, or if it was chopper harvested, or
both. In some areas and in Australia in particular where all
cane is chopper harvested, knives have been removed
completely.
The cane knives as used in South Africa are therefore seen
to have four different roles:
• Leveller mounted on the main cane carrier with a clear-
ance of 500 to 1500 mm, mainly to facilitate feeding into
the main cane knives.
• Primary knives, with a clearance of 60 to 600 mm to pre-
pare the top layer of cane.
• Main knives, with a clearance of 10 to 40 mm, to complete
the knifing operation.
ML UF FX. AK MS. ME GH. NB IL SZD MH. UA
• Feed knives mounted above the shredder, to break up PG EN FXtl OL MSb GO GHb UC SZ. UK MHb SM
lumps in the feed and to accelerate the cane blanket into MILLPREPARATION LINE
the nip of the shredder. It also probably assists the shred-
der by cutting the cane slightly more than the last knife. FIGURE 1 Distribution of specific power consumption of -knives

159
Proceedings of The South African Sugar Technologists' Association - June 1994

but it is easily conveyed on the rubber belt. The preparation forces the cutting edge against wear. As the steel backing
is very good when the knives have been freshly sharpened, wears away, the layer of hard facing remains to provide a
and particularly when handling burnt cane. fairly sharp edge.
The smooth, controlled feed into the shredder through
hydraulically-driven feeder rolls was not very successful from
the start and the operation of this part of the mill has been Maintenance
altered. The major maintenance expenditure on knives is in re-
The total installed power of each of the preparation lines furbishing the cutting surfaces because of wear. This is caused
ranges from 242 kW at EN to 2235 kW at ML. These totals by the relatively large amount of sand which is brought in
have been divided by the fibre throughput for the 1991/92 with the cane, especially during rainy weather. Every knife
season, which season was selected because it was before the must be built up and hard faced by arc welding on a weekly
start of the drought. These specific installed power figures or fortnightly schedule, and the palms are usually built up
vary from 28 at GD to 126 at GH-A with the average being and hard faced in: the: same way once or twice during the
50 kW per ton fibre per hour (See Figure I). The high value season.
for GH-A, which is the diffuser line, results from the fact Very little has changed in cane knife technology since the
that the main knife turbine is oversized, and its power is mid-seventies. Nurick(1975) completed a study of knifing
seldom used to the full. and of the power absorbed by knives at FX (old mill), GH
The speed of rotation of cane knives varies from 250 to and SZ for his MSc, in which one of the main conclusions
960, with most being in the region of 600 rpm. The effec- was that the power absorbed by knives had not changed for
tiveness depends to a large extent on the tip velocity of the many years.
knives which for the lines in the survey ranges from 22 (FX There have been some investigations by the SMRI and
billeter) to 80 ms-I (PG, NB) (see Figure 2). also by many mills into the materials and techniques used
in hard facing. The SMRI conducted an extended research
00...----..,.----------....------------, programme spanning four years from 1980 to 1983 into the
wear on shredder hammers and knives. The specific work
on knives took place during' the last two years and was re-
ported by Schlaudraff (1982, 1983). The most promising de-
velopment from this work was in the use of high chrome
.;, cast alloy steel inserts such as "Apex 26" which could be
E .either bolted or, preferably, welded to the knives and re-
~ placed as they wear.
(3 It is expected that there will be a revival in the testing of
o
...J
W
wear resisting materials for hammers and knives in the near
> future, because there isno doubt that refurbishment of these
a,
i= remains one of the most expensive maintenance expendi-
tures in the sugar mill.

Preparation achieved by knives

lolL UF FXa AI( Msa ME GHa NB IL S2l:l MHa UR The preparation index (PI) of the knives is not measured
PG EN FXb OL MSb GO GHb UC SZa UK MHb SM
regularly at any mills. Historical figures from those mills
MILL PREPARATION LINE
which did not have shredders, for example Empangeni, in-
dicate that knives alone were able to give PI figures as high
FIGURE 2 Distribution of the tip velocity of knives
as 90 and in this instance in 1981 the EM diffuser was able
to achieve an extraction of 97,76% with a bagasse diffuser.
Ten of the preparation lines have turbine drives for one The range in PI was from about 75 up to 85 for those knives
or more of the knives. In these cases the power of each is where PI was measured in 1974.
higher than their electrically-driven counterparts. Moor (1974) reported that the knives at MS (then Tongaat)
mill were providing a PI ofbetween 65 and 70. Nurick (1975)
reported PI figures from the final knives at the old FX mill,
Design and operational features GH and SZ ranging from 46 to 79. The higher figure was
achieved at GH where. the knife was enhanced by welding
The typical knife rotor consists of a shaft to which twenty a block of steel to the cutting edge, hence providing a certain
or more palms are keyed. Two knives are attached to each amount of shredding action.It should be noted that it is not
palm, and the palms are staggered in angular position along easy to measure PI of knifed cane because of the difficulty
the length of the shaft. of ensuring a valid sample, The analyst may be tempted to
The attachment of the knives varies in design, most using remove any large pieces of whole-stick cane, thus inflating
some kind ofquick release arrangement in which centrifugal the PI measurement.
force tends to secure the knife. Some palms are pivoted to
bosses on the shaft so that the knives can swing radially to
avoid damage by rocks and tramp iron. Hybrid types
Most mills use the same design of knife consisting of a Some hybrid type knives/shredders have appeared on the
plate about 20 mm thick with a mass of between 12 and market and have achieved success in many parts of the world,
20 kg. The cutting edge is provided by forging or gas cutting but not yet in South Africa. The most popular example is
a chamfer on the leading edge and the end. The flat face of the "Unigrator" of the Unice Machine Company, of the
the knife is covered with a layer of hard facing which rein- USA.

160
Proceedings of The South African Sugar Technologists' Association - June 1994

This machine combines the knifing and shredding oper- remains one of the most expensive maintenance functions
ation in one unit. The rotor cuts upwards into the cane and and more research work is warranted to try to reduce these
then pulls it over onto a washboard where shredding takes expenses.
place. The hammers are shaped in such a way that they can
perform both functions (Ducasse, 1974).
REFERENCES
Conclusions Ducasse, V (1974). Heavy duty chopper-fiberiser. Proc int Soc Sug Cane
Technol XV: 1568 1574.
It would appear that there are conditions in which the Moor, BStC(1974). An evaluation of very fine shredding. Proc 'int Soc Sug
traditional cane knife in a sugar mill can be dispensed with Cane Technol XV: 1590 - 1603.
altogether. This would be a very interesting development if Nurick,GN (1975). Cane preparation with specialreference to knifing. SMR1
Communication No. 104. 56 pp.
it were to be tried in South Africa, where the opinion exists Reid, MJ (1992). South Africansugarfactoryplant installations 1992. SMRI
that the cane is much more difficult to prepare and process Communication No. 156. (September). 33 pp.
than in most countries. Schlaudraff, JE (1982). Testingof wear resistant materials on shredder ham-
mers and knives. SMRI Technical Report No. 1305 (5 March): 39·pp.
There is still a large area of uncertainty surrounding the Schlaudraff, JE (1983). Testingof wear resistant materials on shredder ham-
method of refurbishment of cane knives and hammers. This mers and knives. SMRI Technical Report No. 1340(14 February): 37 pp.

161