77.

42 Ft Monopole Tower Structural Analysis April 08, 2019

Project Number 00019-0067.001.7205 Page 2

TABLE OF CONTENTS

1) INTRODUCTION

2) ANALYSIS CRITERIA
Table 1 - Proposed Antenna and Cable Information

3) ANALYSIS PROCEDURE
Table 2 - Documents Provided
3.1) Analysis Method
3.2) Assumptions

4) ANALYSIS RESULTS
Table 3 - Section Capacity (Summary)
Table 4 – Tower Component Stresses vs. Capacity
4.1) Recommendations

5) APPENDIX A
tnxTower Output

6) APPENDIX B
Additional Calculations

tnxTower Report - version 8.0.5.0

77.42 Ft Monopole Tower Structural Analysis April 08, 2019
Project Number 00019-0067.001.7205 Page 3

1) INTRODUCTION

This tower is a 85-ft Monopole tower designed by ARE Telecom.

2) ANALYSIS CRITERIA

TIA-222 Revision: TIA-222-G

Risk Category: II
Wind Speed: 89.1 mph
Exposure Category: C
Topographic Factor: 5
Ice Thickness: 0 in
Wind Speed with Ice: 30 mph
Service Wind Speed: 60 mph

Table 1 - Proposed Antenna and Cable Information

Center
Number Number Feed
Mounting Line Antenna
of Antenna Model of Feed Line Note
Level (ft) Elevation Manufacturer
Antennas Lines Size (in)
(ft)
XXQLH-654L8H8-IVT w/
6 ace
Mount Pipe
6 1-5/8
AirScale Dual RRH 4T4R
81.0 81.0 3 nokia 2 7/8
B12/14 320W AHLBA
1 3/8
12.5-Ft V-Frame Sector
3 sitePro1
Mounts [VFA12-RRU]
74.0 74.0 1 commscope MD-S6 ICE SHIELD - -
1 radiowaves SHP6-5.9
RM-DM-6 DUAL RING
1 commscope
69.0 69.0 MOUNT
2 3/8 -
2-IN SCHEDULE 40 X
2 pole mounts
10-FT STIFF ARM PIPES
68.0 68.0 2 nokia MPT-XP-HQAM
67.0 67.0 1 commscope MD-S6 ICE SHIELD - -
1 commscope UHX6-59-D3A/L
RM-DM-6 DUAL RING
1 commscope
62.0 62.0 MOUNT
2 3/8
2-IN SCHEDULE 40 X
2 pole mounts
10-FT STIFF ARM PIPES
61.0 61.0 4 nokia MPT-XP-HQAM

3) ANALYSIS PROCEDURE

Table 2 - Documents Provided

Document Source Reference Date

POLE AND AFS-1700 25_9m afs1700

ARE TELECOM 3/18/2019
DRAWING DRAWING REVB
GEOTECHNICAL REPORT TERRACON 68085099 11/6/2008

tnxTower Report - version 8.0.5.0

77.42 Ft Monopole Tower Structural Analysis April 08, 2019
Project Number 00019-0067.001.7205 Page 4

3.1) Analysis Method

tnxTower (version 8.0.5.0), a commercially available analysis software package, was used to create a
three-dimensional model of the tower and calculate member stresses for various loading cases.
Selected output from the analysis is included in Appendix A.

3.2) Assumptions

1) Tower and structures will be built in accordance with the manufacturer’s specifications.
2) The configuration of antennas, transmission cables, mounts and other appurtenances are as
specified in Tables 1.
3) This analysis review has been performed on the wind load resisting system of the pole and
foundation. Analysis of the hydraulic jacking system was not part of the scope of servcies.

This analysis may be affected if any assumptions are not valid or have been made in error. Paul J.
Ford and Company should be notified to determine the effect on the structural integrity of the tower.

4) ANALYSIS RESULTS

Table 3 - Section Capacity (Summary)

Section Critical SF*P_allow %
Elevation (ft) Component Type Size P (K) Pass / Fail
No. Element (K) Capacity
L1 85 - 66.58 Pole TP19.5x12.1x0.25 1 -7 1142 47.7 Pass
L2 66.58 - 37.05 Pole TP31.4x19.5x0.314 2 -11 2302 68.6 Pass
L3 37.05 - 13.48 Pole TP40.9x31.4x0.375 3 -16 3512 60.0 Pass
L4 13.48 - 7.58 Pole TP42.7x40.9x0.375 4 -18 3623 62.1 Pass
Summary
Pole (L2) 68.6 Pass
Rating = 68.6 Pass

Table 4 - Tower Component Stresses vs. Capacity

Notes Component Elevation (ft) % Capacity Pass / Fail

1 Anchor Rods 7.6 80.1 Pass

1 Base Plate 7.6 57.0 Pass
1 Base Foundation 0 98.5 Pass
Base Foundation
1 0 67.1 Pass
Soil Interaction

Structure Rating (max from all components) = 98.5%

Notes:
1) See additional documentation in “Appendix C – Additional Calculations” for calculations supporting the % capacity
consumed.

4.1) Recommendations

The monopole and its foundation have sufficient capacity to carry the proposed loading configuration.

tnxTower Report - version 8.0.5.0

77.42 Ft Monopole Tower Structural Analysis April 08, 2019
Project Number 00019-0067.001.7205 Page 5

STANDARD CONDITIONS FOR FURNISHING OF PROFESSIONAL ENGINEERING SERVICES ON

EXISTING STRUCTURES BY PAUL J. FORD AND COMPANY

1) The monopole has been analyzed according to the minimum basic design wind velocity
recommended by the Telecommunications Industry Association Standard ANSI/TIA-222-G . If the
owner or local or state agencies require a higher design wind velocity, Paul J. Ford and Company
should be made aware of this requirement.

2) Miscellaneous items such as antenna mounts, etc., have not been designed or detailed as part of
our work. We recommend that material of adequate size and strength be purchased from a
reputable tower manufacturer.

tnxTower Report - version 8.0.5.0

77.42 Ft Monopole Tower Structural Analysis April 08, 2019
Project Number 00019-0067.001.7205 Page 6

APPENDIX A

TNXTOWER OUTPUT

tnxTower Report - version 8.0.5.0

 85.0 ft

AirScale
12.5-Ft
SHP6-5.9
MD-S6
RM-DM-6
(2)
UHX6-59-D3A/L
(4) XXQLH-654L8H8-IVT
10'
MPT-XP-HQAM
xV-Frame
Ice
2"
Dual
DUAL
Sch
Shield
RRH
40
RING
Sector
Pipe
4T4R
MOUNT
Mount
Mounts
w/
B12/14
Mount81
74
69
68
67
62
61
Pipe AHLBA
320W
[SitePro1 VFA12-RRU]
DESIGNED APPURTENANCE LOADING
TYPE ELEVATION TYPE ELEVATION
(2) XXQLH-654L8H8-IVT w/ Mount 81 12.5-Ft V-Frame Sector Mounts 81
Pipe [SitePro1 VFA12-RRU]
(2) XXQLH-654L8H8-IVT w/ Mount 81 MD-S6 Ice Shield 74
12.100

19.500 Pipe
18.42

0.250

RM-DM-6 DUAL RING MOUNT 69

0.8
12
1

(2) XXQLH-654L8H8-IVT w/ Mount 81 (2) 10' x 2" Sch 40 Pipe Mount 69

Pipe
SHP6-5.9 69
AirScale Dual RRH 4T4R B12/14 81
320W AHLBA (2) MPT-XP-HQAM 68
MD-S6 Ice Shield 67
AirScale Dual RRH 4T4R B12/14 81
320W AHLBA RM-DM-6 DUAL RING MOUNT 62
AirScale Dual RRH 4T4R B12/14 81 (2) 10' x 2" Sch 40 Pipe Mount 62
320W AHLBA UHX6-59-D3A/L 62
(4) MPT-XP-HQAM 61
66.6 ft
MATERIAL STRENGTH
GRADE Fy Fu GRADE Fy Fu
A572-65 65 ksi 80 ksi

TOWER DESIGN NOTES

1. Tower is located in Lincoln County, New Mexico.
2. Tower designed for Exposure C to the TIA-222-G Standard.
3. Tower designed for a 89 mph basic wind in accordance with the TIA-222-G Standard.
4. Deflections are based upon a 60 mph wind.
5. Tower Structure Class II.
6. Topographic Category 5 with Crest Height of 2853.00 ft
7. Weld together tower sections have flange connections.
8. Connections use galvanized A325 bolts, nuts and locking devices. Installation per
19.500

31.400

TIA/EIA-222 and AISC Specifications.

29.53

0.314

2.5
18
2

9. Tower members are "hot dipped" galvanized in accordance with ASTM A123 and ASTM
A153 Standards.
10. Welds are fabricated with ER-80S-6 electrodes.
11. Feedlines are to be installed inside of pole and not exposed to wind.
12. TOWER RATING: 68.6%
A572-65

37.0 ft
31.400

40.900
23.57

0.375

3.4
18
3

ALL REACTIONS
ARE FACTORED

13.5 ft AXIAL
18 K
40.900

42.700
0.375
5.90

1.0
18
4

SHEAR MOMENT
34 K 1939 kip-ft
7.6 ft
7.7

TORQUE 4 kip-ft
Number of Sides

REACTIONS - 89 mph WIND

Thickness (in)

Top Dia (in)

Bot Dia (in)

Weight (K)
Length (ft)
Section

Grade

Paul J. Ford and Company Job: 80-Ft Pole: Capitan,NM

Project: 00019-0067.004.7000
250 East Broad st., Suite 600
Client: Drawn by: App'd:
Columbus, OH 43215 ARE Telecom kswarts
Code: Date: Scale:
Phone: (614) 221-6679 TIA-222-G 04/08/19 NTS
Path: Dwg No.
FAX: G:\TOWER\000_Misc\2019\00019-0067 - Captain NM\00019-0067.005\TNX\00019-0067.005.7205.eri E-1
77.42 Ft Monopole Tower Structural Analysis April 08, 2019
Project Number 00019-0067.001.7205 Page 7

Tower Input Data

The tower is a monopole.

This tower is designed using the TIA-222-G standard.
The following design criteria apply:
Tower is located in Lincoln County, New Mexico.
ASCE 7-10 Wind Data is used (wind speeds converted to nominal values).
Basic wind speed of 89 mph.
Structure Class II.
Exposure Category C.
Topographic Category 5.
Crest Height 2853.00 ft.
SEAW RSM-03 procedures for wind speed-up calculations are used.
Topographic Feature: Continuous Ridge.
Slope Distance L: 12672.00 ft.
Distance from Crest x: 0.00 ft.
Deflections calculated using a wind speed of 60 mph.
Weld together tower sections have flange connections..
Connections use galvanized A325 bolts, nuts and locking devices. Installation per TIA/EIA-222 and
AISC Specifications..
Tower members are ''hot dipped'' galvanized in accordance with ASTM A123 and ASTM A153
Standards..
Welds are fabricated with ER-80S-6 electrodes..
Feedlines are to be installed inside of pole and not exposed to wind..
A non-linear (P-delta) analysis was used.
Pressures are calculated at each section.
Stress ratio used in pole design is 1.
Local bending stresses due to climbing loads, feed line supports, and appurtenance mounts are not
considered.

Options
Consider Moments - Legs Distribute Leg Loads As Uniform Use ASCE 10 X-Brace Ly Rules
Consider Moments - Horizontals Assume Legs Pinned Calculate Redundant Bracing Forces
Consider Moments - Diagonals Assume Rigid Index Plate Ignore Redundant Members in FEA
Use Moment Magnification √ Use Clear Spans For Wind Area SR Leg Bolts Resist Compression
√ Use Code Stress Ratios √ Use Clear Spans For KL/r All Leg Panels Have Same Allowable
√ Use Code Safety Factors - Guys Retension Guys To Initial Tension Offset Girt At Foundation
Escalate Ice √ Bypass Mast Stability Checks √ Consider Feed Line Torque
Always Use Max Kz √ Use Azimuth Dish Coefficients Include Angle Block Shear Check
Use Special Wind Profile √ Project Wind Area of Appurt. Use TIA-222-G Bracing Resist.
Exemption
Include Bolts In Member Capacity Autocalc Torque Arm Areas Use TIA-222-G Tension Splice
Exemption
Leg Bolts Are At Top Of Section Add IBC .6D+W Combination Poles
√ Secondary Horizontal Braces Leg Sort Capacity Reports By Component √ Include Shear-Torsion Interaction
Use Diamond Inner Bracing (4 Sided) Triangulate Diamond Inner Bracing Always Use Sub-Critical Flow
SR Members Have Cut Ends Treat Feed Line Bundles As Cylinder Use Top Mounted Sockets
SR Members Are Concentric Ignore KL/ry For 60 Deg. Angle Legs Pole Without Linear Attachments
Pole With Shroud Or No
Appurtenances
Outside and Inside Corner Radii Are
Known

Tapered Pole Section Geometry

tnxTower Report - version 8.0.5.0

77.42 Ft Monopole Tower Structural Analysis April 08, 2019
Project Number 00019-0067.001.7205 Page 8

Section Elevation Section Splice Number Top Bottom Wall Bend Pole Grade
Length Length of Diameter Diameter Thickness Radius
ft ft ft Sides in in in in
L1 85.00-66.58 18.42 0.00 12 12.100 19.500 0.250 1.000 A572-65
(65 ksi)
L2 66.58-37.05 29.53 0.00 18 19.500 31.400 0.314 1.256 A572-65
(65 ksi)
L3 37.05-13.48 23.57 0.00 18 31.400 40.900 0.375 1.500 A572-65
(65 ksi)
L4 13.48-7.58 5.90 18 40.900 42.700 0.375 1.500 A572-65
(65 ksi)

Tapered Pole Properties

Section Tip Dia. Area I r C I/C J It/Q w w/t
in in2 in4 in in in3 in4 in2 in
L1 12.439 9.539 170.977 4.242 6.268 27.279 346.445 4.695 2.573 10.291
20.100 15.496 732.949 6.891 10.101 72.562 1485.154 7.627 4.556 18.224
L2 19.752 19.121 889.257 6.811 9.906 89.770 1779.684 9.563 2.879 9.17
31.836 30.981 3782.410 11.036 15.951 237.124 7569.796 15.494 4.974 15.84
L3 31.827 36.928 4490.669 11.014 15.951 281.525 8987.246 18.467 4.866 12.977
41.473 48.235 10007.940 14.386 20.777 481.679 20029.050 24.122 6.538 17.436
L4 41.473 48.235 10007.940 14.386 20.777 481.679 20029.050 24.122 6.538 17.436
43.301 50.377 11401.619 15.025 21.692 525.624 22818.241 25.193 6.855 18.281

Tower Gusset Gusset Gusset Grade Adjust. Factor Adjust. Weight Mult. Double Angle Double Angle Double Angle
Elevation Area Thickness Af Factor Stitch Bolt Stitch Bolt Stitch Bolt
(per face) Ar Spacing Spacing Spacing
Diagonals Horizontals Redundants
ft ft2 in in in in
L1 85.00- 1 1 1
66.58
L2 66.58- 1 1 1
37.05
L3 37.05- 1 1 1
13.48
L4 13.48-7.58 1 1 1

Feed Line/Linear Appurtenances - Entered As Area

Description Face Allow Exclude Componen Placement Total CAAA Weight
or Shield From t Number
Leg Torque Type ft ft2/ft plf
Calculation
LDF7-50A (1 5/8'' C No No Inside Pole 81.00 - 7.58 6 No Ice 0.00 0.92
foam)
6-8AWG 3 PAIR( C No No Inside Pole 81.00 - 7.58 2 No Ice 0.00 0.68
7/8'')
FB-L98B-002- C No No Inside Pole 81.00 - 7.58 1 No Ice 0.00 0.06
100000( 3/8'')
FB-L98B-002- C No No Inside Pole 69.00 - 7.58 2 No Ice 0.00 0.06
100000( 3/8'')
FB-L98B-002- C No No Inside Pole 62.00 - 7.58 2 No Ice 0.00 0.06
100000( 3/8'')

Feed Line/Linear Appurtenances Section Areas

tnxTower Report - version 8.0.5.0

77.42 Ft Monopole Tower Structural Analysis April 08, 2019
Project Number 00019-0067.001.7205 Page 9

Tower Tower Face AR AF CAAA CAAA Weight

Sectio Elevation In Face Out Face
2 2
n ft ft ft ft2 ft2 K
L1 85.00-66.58 A 0.000 0.000 0.000 0.000 0
B 0.000 0.000 0.000 0.000 0
C 0.000 0.000 0.000 0.000 0
L2 66.58-37.05 A 0.000 0.000 0.000 0.000 0
B 0.000 0.000 0.000 0.000 0
C 0.000 0.000 0.000 0.000 0
L3 37.05-13.48 A 0.000 0.000 0.000 0.000 0
B 0.000 0.000 0.000 0.000 0
C 0.000 0.000 0.000 0.000 0
L4 13.48-7.58 A 0.000 0.000 0.000 0.000 0
B 0.000 0.000 0.000 0.000 0
C 0.000 0.000 0.000 0.000 0

Feed Line Center of Pressure

Section Elevation CPX CPZ CPX CPZ
Ice Ice
ft in in in in
L1 85.00-66.58 0.000 0.000 0.000 0.000
L2 66.58-37.05 0.000 0.000 0.000 0.000
L3 37.05-13.48 0.000 0.000 0.000 0.000
L4 13.48-7.58 0.000 0.000 0.000 0.000

Note: For pole sections, center of pressure calculations do not consider feed line shielding.

Shielding Factor Ka
Tower Feed Line Description Feed Line Ka Ka
Section Record No. Segment No Ice Ice
Elev.

Discrete Tower Loads

Description Face Offset Offsets: Azimuth Placement CAAA CAAA Weight
or Type Horz Adjustmen Front Side
Leg Lateral t
Vert
ft ft ft2 ft2 K
ft °
ft
(2) XXQLH-654L8H8-IVT A From Leg 4.00 0.000 81.00 No Ice 17.38 10.10 0
w/ Mount Pipe 0
0
(2) XXQLH-654L8H8-IVT B From Leg 4.00 0.000 81.00 No Ice 17.38 10.10 0
w/ Mount Pipe 0
0
(2) XXQLH-654L8H8-IVT C From Leg 4.00 0.000 81.00 No Ice 17.38 10.10 0
w/ Mount Pipe 0
0
AirScale Dual RRH 4T4R A From Leg 4.00 0.000 81.00 No Ice 3.68 2.31 0
B12/14 320W AHLBA 0
0
AirScale Dual RRH 4T4R B From Leg 4.00 0.000 81.00 No Ice 3.68 2.31 0
B12/14 320W AHLBA 0
0
AirScale Dual RRH 4T4R C From Leg 4.00 0.000 81.00 No Ice 3.68 2.31 0
B12/14 320W AHLBA 0
0
tnxTower Report - version 8.0.5.0
77.42 Ft Monopole Tower Structural Analysis April 08, 2019
Project Number 00019-0067.001.7205 Page 10

Description Face Offset Offsets: Azimuth Placement CAAA CAAA Weight

or Type Horz Adjustmen Front Side
Leg Lateral t
Vert
ft ft ft2 ft2 K
ft °
ft
12.5-Ft V-Frame Sector C None 0.000 81.00 No Ice 28.37 28.37 3
Mounts [SitePro1 VFA12-
RRU]
***
MD-S6 Ice Shield C None 0.000 74.00 No Ice 11.67 5.60 0
(2) MPT-XP-HQAM C None 0.000 68.00 No Ice 0.71 0.53 0
RM-DM-6 DUAL RING C None 0.000 69.00 No Ice 7.00 7.00 0
MOUNT
(2) 10' x 2'' Sch 40 Pipe C None 0.000 69.00 No Ice 2.38 2.38 0
Mount
***
MD-S6 Ice Shield B None 0.000 67.00 No Ice 11.67 5.60 0
(4) MPT-XP-HQAM B None 0.000 61.00 No Ice 0.71 0.53 0
RM-DM-6 DUAL RING B None 0.000 62.00 No Ice 7.00 7.00 0
MOUNT
(2) 10' x 2'' Sch 40 Pipe B None 0.000 62.00 No Ice 2.38 2.38 0
Mount

Dishes
Description Face Dish Offset Offsets: Azimuth 3 dB Elevation Outside Aperture Weight
or Type Type Horz Adjustment Beam Diameter Area
Leg Lateral Width
Vert
ft ° ° ft ft ft2 K
SHP6-5.9 C Paraboloid From 0.00 9.000 69.00 5.83 No Ice 26.73 0
w/Shroud (HP) Leg 0
0
****
UHX6-59-D3A/L B Paraboloid From 0.00 45.000 62.00 6.46 No Ice 32.76 0
w/Shroud (HP) Leg 0
0

222-G Verification Constants

Constant Value
Wind Importance Factor Without Ice 1
Wind Importance Factor With Ice Factor 1
Ice Importance Factor 1
Kd 0.95
Zg 900
 9.5
Kzmin 0.85
Ke 1
Kt 1
f 1

222-G Section Verification ArRr By Element

Section Elem. Size C C F e e Ar Ar ArRr ArRr
Elevation Num. w/Ice a w/Ice w/Ice w/Ice
c
ft e ft2 ft2 ft2 ft2

tnxTower Report - version 8.0.5.0

77.42 Ft Monopole Tower Structural Analysis April 08, 2019
Project Number 00019-0067.001.7205 Page 11

Section Elem. Size C C F e e Ar Ar ArRr ArRr

Elevation Num. w/Ice a w/Ice w/Ice w/Ice
c
ft e ft2 ft2 ft2 ft2
L1 85.00- 1 TP19.5x12.1x0.25 215.27 72.564 1 1 24.973 24.973 24.973 24.973
66.58 4
Sum: 24.973 24.973 24.973 24.973
L2 66.58- 2 TP31.4x19.5x0.314 328.94 110.88 1 1 63.475 63.475 63.475 63.475
37.05 7 1
Sum: 63.475 63.475 63.475 63.475
L3 37.05- 3 TP40.9x31.4x0.375 435.52 146.80 1 1 71.986 71.986 71.986 71.986
13.48 7 7
Sum: 71.986 71.986 71.986 71.986
L4 13.48-7.58 4 TP42.7x40.9x0.375 479.43 161.60 1 1 20.840 20.840 20.840 20.840
1 6
Sum: 20.840 20.840 20.840 20.840

222-G Section Verification Tables - No Ice

Section zwind zice Kz Kh Kzt tz qz F e ArRr
Elevation a
c
ft ft ft in psf e ft2
L1 85.00-66.58 75.07 1.191 1 2.671 61.32 1 24.973
L2 66.58-37.05 50.66 1.097 1 2.696 56.96 1 63.475
L3 37.05-13.48 24.75 0.943 1 2.722 49.46 1 71.986
L4 13.48-7.58 10.51 0.85 1 2.736 44.80 1 20.840

222-G Section Verification Tables - Service

Section zwind zice Kz Kh Kzt tz qz F e ArRr
Elevation a
c
ft ft ft in psf e ft2
L1 85.00-66.58 75.07 1.191 1 2.671 24.93 1 24.973
L2 66.58-37.05 50.66 1.097 1 2.696 23.16 1 63.475
L3 37.05-13.48 24.75 0.943 1 2.722 20.11 1 71.986
L4 13.48-7.58 10.51 0.85 1 2.736 18.22 1 20.840

Tower Pressures - No Ice

GH = 1.100

Section z KZ qz AG F AF AR Aleg Leg CAAA CAAA

Elevation a % In Out
c Face Face
ft ft psf ft2 e ft2 ft2 ft2 ft2 ft2
L1 85.00- 75.07 1.191 61.32 24.973 A 0.000 24.973 24.973 100.00 0.000 0.000
66.58 B 0.000 24.973 100.00 0.000 0.000
C 0.000 24.973 100.00 0.000 0.000
L2 66.58- 50.66 1.097 56.96 63.475 A 0.000 63.475 63.475 100.00 0.000 0.000
37.05 B 0.000 63.475 100.00 0.000 0.000
C 0.000 63.475 100.00 0.000 0.000
L3 37.05- 24.75 0.943 49.46 71.986 A 0.000 71.986 71.986 100.00 0.000 0.000
13.48 B 0.000 71.986 100.00 0.000 0.000
C 0.000 71.986 100.00 0.000 0.000
L4 13.48-7.58 10.51 0.85 44.80 20.840 A 0.000 20.840 20.840 100.00 0.000 0.000
B 0.000 20.840 100.00 0.000 0.000
C 0.000 20.840 100.00 0.000 0.000

tnxTower Report - version 8.0.5.0

77.42 Ft Monopole Tower Structural Analysis April 08, 2019
Project Number 00019-0067.001.7205 Page 12

Tower Pressure - Service

GH = 1.100

Section z KZ qz AG F AF AR Aleg Leg CAAA CAAA

Elevation a % In Out
c Face Face
ft ft psf ft2 e ft2 ft2 ft2 ft2 ft2
L1 85.00- 75.07 1.191 24.93 24.973 A 0.000 24.973 24.973 100.00 0.000 0.000
66.58 B 0.000 24.973 100.00 0.000 0.000
C 0.000 24.973 100.00 0.000 0.000
L2 66.58- 50.66 1.097 23.16 63.475 A 0.000 63.475 63.475 100.00 0.000 0.000
37.05 B 0.000 63.475 100.00 0.000 0.000
C 0.000 63.475 100.00 0.000 0.000
L3 37.05- 24.75 0.943 20.11 71.986 A 0.000 71.986 71.986 100.00 0.000 0.000
13.48 B 0.000 71.986 100.00 0.000 0.000
C 0.000 71.986 100.00 0.000 0.000
L4 13.48-7.58 10.51 0.85 18.22 20.840 A 0.000 20.840 20.840 100.00 0.000 0.000
B 0.000 20.840 100.00 0.000 0.000
C 0.000 20.840 100.00 0.000 0.000

Load Combinations
Comb. Description
No.
1 Dead Only
2 1.2 Dead+1.6 Wind 0 deg - No Ice
3 0.9 Dead+1.6 Wind 0 deg - No Ice
4 1.2 Dead+1.6 Wind 30 deg - No Ice
5 0.9 Dead+1.6 Wind 30 deg - No Ice
6 1.2 Dead+1.6 Wind 60 deg - No Ice
7 0.9 Dead+1.6 Wind 60 deg - No Ice
8 1.2 Dead+1.6 Wind 90 deg - No Ice
9 0.9 Dead+1.6 Wind 90 deg - No Ice
10 1.2 Dead+1.6 Wind 120 deg - No Ice
11 0.9 Dead+1.6 Wind 120 deg - No Ice
12 1.2 Dead+1.6 Wind 150 deg - No Ice
13 0.9 Dead+1.6 Wind 150 deg - No Ice
14 1.2 Dead+1.6 Wind 180 deg - No Ice
15 0.9 Dead+1.6 Wind 180 deg - No Ice
16 1.2 Dead+1.6 Wind 210 deg - No Ice
17 0.9 Dead+1.6 Wind 210 deg - No Ice
18 1.2 Dead+1.6 Wind 240 deg - No Ice
19 0.9 Dead+1.6 Wind 240 deg - No Ice
20 1.2 Dead+1.6 Wind 270 deg - No Ice
21 0.9 Dead+1.6 Wind 270 deg - No Ice
22 1.2 Dead+1.6 Wind 300 deg - No Ice
23 0.9 Dead+1.6 Wind 300 deg - No Ice
24 1.2 Dead+1.6 Wind 330 deg - No Ice
25 0.9 Dead+1.6 Wind 330 deg - No Ice
26 Dead+Wind 0 deg - Service
27 Dead+Wind 30 deg - Service
28 Dead+Wind 60 deg - Service
29 Dead+Wind 90 deg - Service
30 Dead+Wind 120 deg - Service
31 Dead+Wind 150 deg - Service
32 Dead+Wind 180 deg - Service
33 Dead+Wind 210 deg - Service
34 Dead+Wind 240 deg - Service
35 Dead+Wind 270 deg - Service
36 Dead+Wind 300 deg - Service
37 Dead+Wind 330 deg - Service

tnxTower Report - version 8.0.5.0

77.42 Ft Monopole Tower Structural Analysis April 08, 2019
Project Number 00019-0067.001.7205 Page 13

Maximum Tower Deflections - Service Wind

Section Elevation Horz. Gov. Tilt Twist
No. Deflection Load
ft in Comb. ° °
L1 85 - 66.58 9.91 27 1.186 0.006
L2 66.58 - 37.05 5.56 27 0.994 0.006
L3 37.05 - 13.48 1.20 27 0.409 0.001
L4 13.48 - 7.58 0.05 27 0.073 0.000

Critical Deflections and Radius of Curvature - Service Wind

Elevation Appurtenance Gov. Deflection Tilt Twist Radius of
Load Curvature
ft Comb. in ° ° ft
81.00 (2) XXQLH-654L8H8-IVT w/ 27 8.92 1.153 0.007 10054
Mount Pipe
74.00 MD-S6 Ice Shield 27 7.22 1.087 0.007 4570
69.00 SHP6-5.9 27 6.08 1.028 0.007 3166
68.00 (2) MPT-XP-HQAM 27 5.86 1.014 0.007 3016
67.00 MD-S6 Ice Shield 27 5.65 1.000 0.007 2906
62.00 UHX6-59-D3A/L 27 4.65 0.918 0.006 2798
61.00 (4) MPT-XP-HQAM 27 4.46 0.900 0.006 2814

Maximum Tower Deflections - Design Wind

Section Elevation Horz. Gov. Tilt Twist
No. Deflection Load
ft in Comb. ° °
L1 85 - 66.58 39.06 4 4.679 0.023
L2 66.58 - 37.05 21.92 4 3.922 0.023
L3 37.05 - 13.48 4.74 4 1.613 0.006
L4 13.48 - 7.58 0.18 4 0.289 0.001

Critical Deflections and Radius of Curvature - Design Wind

Elevation Appurtenance Gov. Deflection Tilt Twist Radius of
Load Curvature
ft Comb. in ° ° ft
81.00 (2) XXQLH-654L8H8-IVT w/ 4 35.14 4.549 0.028 2575
Mount Pipe
74.00 MD-S6 Ice Shield 4 28.45 4.291 0.029 1170
69.00 SHP6-5.9 4 23.97 4.057 0.028 810
68.00 (2) MPT-XP-HQAM 4 23.11 4.003 0.028 771
67.00 MD-S6 Ice Shield 4 22.27 3.946 0.027 743
62.00 UHX6-59-D3A/L 4 18.33 3.622 0.025 714
61.00 (4) MPT-XP-HQAM 4 17.59 3.549 0.024 718

Compression Checks

Pole Design Data

tnxTower Report - version 8.0.5.0

77.42 Ft Monopole Tower Structural Analysis April 08, 2019
Project Number 00019-0067.001.7205 Page 14

Section Elevation Size L Lu Kl/r A Pu Pn Ratio

No. Pu
2
ft ft ft in K K Pn
L1 85 - 66.58 (1) TP19.5x12.1x0.25 18.42 0.00 0.0 15.496 -7 1142 0.006
L2 66.58 - 37.05 TP31.4x19.5x0.314 29.53 0.00 0.0 30.981 -11 2302 0.005
(2)
L3 37.05 - 13.48 TP40.9x31.4x0.375 23.57 0.00 0.0 48.235 -16 3512 0.005
(3)
L4 13.48 - 7.58 TP42.7x40.9x0.375 5.90 0.00 0.0 50.377 -18 3623 0.005
(4)

Pole Bending Design Data

Section Elevation Size Mux Mnx Ratio Muy Mny Ratio
No. Mux Muy
ft kip-ft kip-ft Mnx kip-ft kip-ft Mny
L1 85 - 66.58 (1) TP19.5x12.1x0.25 209 446 0.470 0 446 0.000
L2 66.58 - 37.05 TP31.4x19.5x0.314 998 1468 0.680 0 1468 0.000
(2)
L3 37.05 - 13.48 TP40.9x31.4x0.375 1739 2922 0.595 0 2922 0.000
(3)
L4 13.48 - 7.58 TP42.7x40.9x0.375 1939 3150 0.616 0 3150 0.000
(4)

Pole Shear Design Data

Section Elevation Size Actual Vn Ratio Actual Tn Ratio
No. Vu Vu Tu Tu
ft K K Vn kip-ft kip-ft Tn
L1 85 - 66.58 (1) TP19.5x12.1x0.25 21 571 0.037 1 908 0.001
L2 66.58 - 37.05 TP31.4x19.5x0.314 30 1151 0.026 3 2944 0.001
(2)
L3 37.05 - 13.48 TP40.9x31.4x0.375 33 1756 0.019 3 5860 0.000
(3)
L4 13.48 - 7.58 TP42.7x40.9x0.375 34 1811 0.019 3 6316 0.000
(4)

Pole Interaction Design Data

Section Elevation Ratio Ratio Ratio Ratio Ratio Comb. Allow. Criteria
No. Pu Mux Muy Vu Tu Stress Stress
ft Pn Mnx Mny Vn Tn Ratio Ratio
L1 85 - 66.58 (1) 0.006 0.470 0.000 0.037 0.001 0.477 1.000
4.8.2

L2 66.58 - 37.05 0.005 0.680 0.000 0.026 0.001 0.686 1.000

4.8.2
(2)
L3 37.05 - 13.48 0.005 0.595 0.000 0.019 0.000 0.600 1.000
4.8.2
(3)
L4 13.48 - 7.58 0.005 0.616 0.000 0.019 0.000 0.621 1.000
4.8.2
(4)

tnxTower Report - version 8.0.5.0

77.42 Ft Monopole Tower Structural Analysis April 08, 2019
Project Number 00019-0067.001.7205 Page 15

Section Capacity Table

Section Elevation Component Size Critical P øPallow % Pass
No. ft Type Element K K Capacity Fail
L1 85 - 66.58 Pole TP19.5x12.1x0.25 1 -7 1142 47.7 Pass
L2 66.58 - 37.05 Pole TP31.4x19.5x0.314 2 -11 2302 68.6 Pass
L3 37.05 - 13.48 Pole TP40.9x31.4x0.375 3 -16 3512 60.0 Pass
L4 13.48 - 7.58 Pole TP42.7x40.9x0.375 4 -18 3623 62.1 Pass
Summary
Pole (L2) 68.6 Pass
RATING = 68.6 Pass

tnxTower Report - version 8.0.5.0

77.42 Ft Monopole Tower Structural Analysis April 08, 2019
Project Number 00019-0067.001.7205 Page 16

APPENDIX B

ADDITIONAL CALCULATIONS

tnxTower Report - version 8.0.5.0

 Stiffened or Unstiffened, Exterior Flange Plate - Any Bolt Material TIA Rev G
Reactions Bolt Threads:
Site Data Mu 209 ft-kips X-Excluded
BU#: Axial, Pu: 7 kips φVn=φ(0.55*Ab*Fu)
Site Name: Shear, Vu: 21 kips φ=0.75, φ*Vn (kips):
App #: Elevation: 66.6 feet 64.31

Pole Manufacturer: Other TIA G

If No stiffeners, Criteria: <-Only Applcable to Unstiffened Cases
Flange Bolt Results Rigid
Bolt Data Bolt Tension Capacity, φ*Tn,B1: 91.35 kips φ*Tn
Qty: 16 Adjusted φ*Tn (due to Vu=Vu/Qty), B: 91.33 kips φTn[(1-(Vu/φVn)^2]^0.5
Diameter (in.): 1.375 Bolt Fu: 105 Max Bolt directly applied Tu: 25.04 Kips
Bolt Material: A325 Bolt Fy: 81 Min. PL "tc" for B cap. w/o Pry: 1.744 in
N/A: 75 <-- Disregard Min PL "treq" for actual T w/ Pry: 0.717 in
N/A: 55 <-- Disregard Min PL "t1" for actual T w/o Pry: 0.913 in
Circle (in.): 24.61 T allowable with Prying: 84.16 kips 0≤α'≤1 case
Prying Force, q: 0.00 kips
Plate Data Total Bolt Tension=Tu+q: 25.04 kips
Diam: 28.54 in Prying Bolt Stress Ratio=(Tu+q)/(B): 27.4% Pass
Thick, t: 1.57 in
Grade (Fy): 50 ksi Exterior Flange Plate Results Flexural Check Rigid
Strength, Fu: 65 ksi Compression Side Plate Stress: 15.5 ksi TIA G
Single-Rod B-eff: 3.92 in Allowable Plate Stress: 45.0 ksi φ*Fy
Compression Plate Stress Ratio: 34.5% Pass Comp. Y.L. Length:
Stiffener Data (Welding at Both Sides) No Prying 15.01
Config: 0 * Tension Side Stress Ratio, (treq/t)^2: 20.8% Pass
Weld Type:
Groove Depth: in ** n/a
Groove Angle: degrees Stiffener Results
Fillet H. Weld: <-- Disregard Horizontal Weld : n/a
Fillet V. Weld: in Vertical Weld: n/a
Width: in Plate Flex+Shear, fb/Fb+(fv/Fv)^2: n/a
Height: in Plate Tension+Shear, ft/Ft+(fv/Fv)^2: n/a
Thick: in Plate Comp. (AISC Bracket): n/a
Notch: in Pole Results
Grade: ksi Pole Punching Shear Check: n/a
Weld str.: ksi

Pole Data
Diam: 19.5 in
Thick: 0.25 in
Grade: 65 ksi
# of Sides: 12 "0" IF Round
Fu 80 ksi
Reinf. Fillet Weld 0 "0" if None

* 0 = none, 1 = every bolt, 2 = every 2 bolts, 3 = 2 per bolt

** Note: for complete joint penetration groove welds the groove depth must be exactly 1/2 the stiffener thickness for calculation purposes

CCIplate 1.5 - Ext Flange G 1.3, Effective March 19, 2012 Analysis Date: 4/8/2019
 Stiffened or Unstiffened, Exterior Flange Plate - Any Bolt Material TIA Rev G
Reactions Bolt Threads:
Site Data Mu 998 ft-kips X-Excluded
BU#: Axial, Pu: 11 kips φVn=φ(0.55*Ab*Fu)
Site Name: Shear, Vu: 30 kips φ=0.75, φ*Vn (kips):
App #: Elevation: 37.1 feet 64.31

Pole Manufacturer: Other TIA G

If No stiffeners, Criteria: <-Only Applcable to Unstiffened Cases
Flange Bolt Results Rigid
Bolt Data Bolt Tension Capacity, φ*Tn,B1: 91.35 kips φ*Tn
Qty: 22 Adjusted φ*Tn (due to Vu=Vu/Qty), B: 91.33 kips φTn[(1-(Vu/φVn)^2]^0.5
Diameter (in.): 1.375 Bolt Fu: 105 Max Bolt directly applied Tu: 58.98 Kips
Bolt Material: A325 Bolt Fy: 81 Min. PL "tc" for B cap. w/o Pry: 1.633 in
N/A: 75 <-- Disregard Min PL "treq" for actual T w/ Pry: 1.013 in
N/A: 55 <-- Disregard Min PL "t1" for actual T w/o Pry: 1.313 in
Circle (in.): 36.61 T allowable with Prying: 88.42 kips 0≤α'≤1 case
Prying Force, q: 0.00 kips
Plate Data Total Bolt Tension=Tu+q: 58.98 kips
Diam: 40.55 in Prying Bolt Stress Ratio=(Tu+q)/(B): 64.6% Pass
Thick, t: 1.57 in
Grade (Fy): 50 ksi Exterior Flange Plate Results Flexural Check Rigid
Strength, Fu: 65 ksi Compression Side Plate Stress: 33.7 ksi TIA G
Single-Rod B-eff: 4.59 in Allowable Plate Stress: 45.0 ksi φ*Fy
Compression Plate Stress Ratio: 74.9% Pass Comp. Y.L. Length:
Stiffener Data (Welding at Both Sides) No Prying 18.82
Config: 0 * Tension Side Stress Ratio, (treq/t)^2: 41.6% Pass
Weld Type:
Groove Depth: in ** n/a
Groove Angle: degrees Stiffener Results
Fillet H. Weld: <-- Disregard Horizontal Weld : n/a
Fillet V. Weld: in Vertical Weld: n/a
Width: in Plate Flex+Shear, fb/Fb+(fv/Fv)^2: n/a
Height: in Plate Tension+Shear, ft/Ft+(fv/Fv)^2: n/a
Thick: in Plate Comp. (AISC Bracket): n/a
Notch: in Pole Results
Grade: ksi Pole Punching Shear Check: n/a
Weld str.: ksi

Pole Data
Diam: 31.4 in
Thick: 0.314 in
Grade: 65 ksi
# of Sides: 12 "0" IF Round
Fu 80 ksi
Reinf. Fillet Weld 0 "0" if None

* 0 = none, 1 = every bolt, 2 = every 2 bolts, 3 = 2 per bolt

** Note: for complete joint penetration groove welds the groove depth must be exactly 1/2 the stiffener thickness for calculation purposes

CCIplate 1.5 - Ext Flange G 1.3, Effective March 19, 2012 Analysis Date: 4/8/2019
 Stiffened or Unstiffened, Exterior Flange Plate - Any Bolt Material TIA Rev G
Reactions Bolt Threads:
Site Data Mu 1739 ft-kips X-Excluded
BU#: Axial, Pu: 16 kips φVn=φ(0.55*Ab*Fu)
Site Name: Shear, Vu: 33 kips φ=0.75, φ*Vn (kips):
App #: Elevation: 13.5 feet 64.31

Pole Manufacturer: Other TIA G

If No stiffeners, Criteria: <-Only Applcable to Unstiffened Cases
Flange Bolt Results Rigid
Bolt Data Bolt Tension Capacity, φ*Tn,B1: 91.35 kips φ*Tn
Qty: 36 Adjusted φ*Tn (due to Vu=Vu/Qty), B: 91.34 kips φTn[(1-(Vu/φVn)^2]^0.5
Diameter (in.): 1.375 Bolt Fu: 105 Max Bolt directly applied Tu: 48.84 Kips
Bolt Material: A325 Bolt Fy: 81 Min. PL "tc" for B cap. w/o Pry: 2.043 in
N/A: 75 <-- Disregard Min PL "treq" for actual T w/ Pry: 1.182 in
N/A: 55 <-- Disregard Min PL "t1" for actual T w/o Pry: 1.494 in
Circle (in.): 47.05 T allowable with Prying: 88.31 kips 0≤α'≤1 case
Prying Force, q: 0.00 kips
Plate Data Total Bolt Tension=Tu+q: 48.84 kips
Diam: 50.98 in Prying Bolt Stress Ratio=(Tu+q)/(B): 53.5% Pass
Thick, t: 1.97 in
Grade (Fy): 50 ksi Exterior Flange Plate Results Flexural Check Rigid
Strength, Fu: 65 ksi Compression Side Plate Stress: 26.3 ksi TIA G
Single-Rod B-eff: 3.65 in Allowable Plate Stress: 45.0 ksi φ*Fy
Compression Plate Stress Ratio: 58.4% Pass Comp. Y.L. Length:
Stiffener Data (Welding at Both Sides) No Prying 23.26
Config: 0 * Tension Side Stress Ratio, (treq/t)^2: 36.0% Pass
Weld Type:
Groove Depth: in ** n/a
Groove Angle: degrees Stiffener Results
Fillet H. Weld: <-- Disregard Horizontal Weld : n/a
Fillet V. Weld: in Vertical Weld: n/a
Width: in Plate Flex+Shear, fb/Fb+(fv/Fv)^2: n/a
Height: in Plate Tension+Shear, ft/Ft+(fv/Fv)^2: n/a
Thick: in Plate Comp. (AISC Bracket): n/a
Notch: in Pole Results
Grade: ksi Pole Punching Shear Check: n/a
Weld str.: ksi

Pole Data
Diam: 40.9 in
Thick: 0.375 in
Grade: 65 ksi
# of Sides: 12 "0" IF Round
Fu 80 ksi
Reinf. Fillet Weld 0 "0" if None

* 0 = none, 1 = every bolt, 2 = every 2 bolts, 3 = 2 per bolt

** Note: for complete joint penetration groove welds the groove depth must be exactly 1/2 the stiffener thickness for calculation purposes

CCIplate 1.5 - Ext Flange G 1.3, Effective March 19, 2012 Analysis Date: 4/8/2019
 Stiffened or Unstiffened, Ungrouted, Circular Base Plate - Any Rod Material
Assumption: Clear space between bottom of leveling nut and top of concrete not exceeding (1)*(Rod
TIA Rev G Diameter)
Site Data Reactions
BU#: Mu: 1939 ft-kips
Site Name: Axial, Pu: 18 kips
App #: Shear, Vu: 34 kips
Pole Manufacturer: Other Eta Factor, η 0.5 TIA G (Fig. 4-4)

Anchor Rod Data If No stiffeners, Criteria: AISC LRFD <-Only Applcable to Unstiffened Cases
Qty: 36
Diam: 1.375 in
Rod Material: Other Anchor Rod Results Rigid
Strength (Fu): 75 ksi Max Rod (Cu+ Vu/ή): 55.8 Kips AISC LRFD
Yield (Fy): 55 ksi Allowable Axial, Φ*Fu*Anet: 69.6 Kips φ*Tn
Bolt Circle: 48.43 in Anchor Rod Stress Ratio: 80.1% Pass

Plate Data
Diam: 52.36 in Base Plate Results Flexural Check Rigid
Thick: 1.97 in Base Plate Stress: 25.6 ksi AISC LRFD
Grade: 50 ksi Allowable Plate Stress: 45.0 ksi φ*Fy
Single-Rod B-eff: 3.81 in Base Plate Stress Ratio: 57.0% Pass Y.L. Length:
22.85
Stiffener Data (Welding at both sides) n/a
Config: 0 * Stiffener Results
Weld Type: Horizontal Weld : n/a
Groove Depth: in ** Vertical Weld: n/a
Groove Angle: degrees Plate Flex+Shear, fb/Fb+(fv/Fv)^2: n/a
Fillet H. Weld: <-- Disregard Plate Tension+Shear, ft/Ft+(fv/Fv)^2:n/a
Fillet V. Weld: in Plate Comp. (AISC Bracket): n/a
Width: in
Height: in Pole Results
Thick: in Pole Punching Shear Check: n/a
Notch: in
Grade: ksi
Weld str.: ksi

Pole Data
Diam: 42.7 in
Thick: 0.375 in
Grade: 65 ksi
# of Sides: 12 "0" IF Round
Fu 80 ksi
Reinf. Fillet Weld 0 "0" if None

* 0 = none, 1 = every bolt, 2 = every 2 bolts, 3 = 2 per bolt

** Note: for complete joint penetration groove welds the groove depth must be exactly 1/2 the stiffener thickness for calculation purposes

CCIplate 1.5 - Circular Base G 1.3, Effective March 19, 2012 Analysis Date: 4/8/2019
Moment Capacity of Round Ballast Foundation PJF job no. AFS-1700

Assumption: Foundation is bearing at or near the ground surface

Uniform bearing stress distribution assumed under foundation when ultimate bearing capacity reached

Foundation Load Check Summary

Pole overturning moment = 1939 ft-kips (at pole base plate)

Pole base shear load = 34 kips
Pole axial load = 18 kips (Load assumed to be centered on cross-section and to have 1.2 load factor)
Base plate to bottom of foundation = 7.58 feet

Foundation axial load reduction factor = 0.9 (Use 1.0 if F-Standard / Working Load analysis)
Foundation steel weight = 26.5 kips (see steel weight calcs spreadsheet)
Foundation diameter = 23.13 feet
Foundation ID = 3.6 ft (Shaft OD plus portion of foundation base without bottom plate)
Ballast unit weight = 110 pcf
Ballast depth= 6.85 ft
Foundation ballast total weight = 241.8 kips

Foundation bottom plate thickness = 0.197 inches

Foundation bottom plate yield strength = 50 ksi
Max plate width, a = 36.3 inches (Larger of two plate dims)
Max plate height, b = 11.8 inches (Smaller of two plate dims)
Bottom plate support condition = F Fixed or Simply Supported (SS)
Width / Height Ratio = 3.08
b= 0.5 From Roark and Young, Table 26.1, 1a (SS) or 8a (Fixed)

Bearing Check
Reduction factor, f = 0.75
Ult soil bearing cap = 8000 psf
Overturning moment at base of foundation, Mu = 2196.7 ft-kips (at pole base plate)
Moment Capacity, fMn = 3440.2 ft-kips (Based on soil bearing area; calculations below)
% Capacity = 63.9% OK

Overturning / Stability Check

Reduction factor = 1.00 (Use 0.67 if F-Standard / Working Load analysis; use 1.0 if G-Standard / LRFD)
Axial load resisting overturning = 283.3 kips (Unfactored)
Overturning moment at base of foundation = 2196.7 ft-kips (at pole base plate)
Moment resisting overturning at foundation toe = 3275.9 ft-kips
% Capacity = 67.1% OK

Bottom Plate Bending Check

Shape factor adjustment = 1.5 (Use 1 if F-Standard / Working Load analysis; use 1.5 if G-Standard / LRFD)
Adjust for ballast overburden pressure? Y (Y or N)
Max foundation bearing stress = 26.6 psi (Adjusted using bearing % Capacity)
Max plate bending stress = 26.2 ksi (Adjusted using bearing % Capacity)
Shape factor adjustment is based
on assumption that Roark & Young
Maximum plate bending capacity = 45.0 ksi
work uses plate section modulus
% Capacity = 58.2% OK

Determination of soil compression area

Load eccentricity = 8.62 feet

Difference = 0.00 (Ao Centroid location - Load eccentricity)
Outside Diameter = 23.13 ft Outside radius of found, ro = 11.57 ft
Inside Diameter = 0.00 in Inside radius of pole, ri = 0.00 in
Neutral axis location = 4.98 ft (Measured from max. compression fiber; formula for annulus area assumes (c) is < 1/2 x OD)
Therefore c= 4.98 feet and a = b 1 x c = 4.98 feet
AlphaO = 0.965 radians
AO = 66.5 square feet Centroid of AO = 8.62 feet above center of section

Area of Annulus = A O - A I = 66.5 square feet Net area of annulus = 66.5 square feet

Centroid of annulus located 20.18 feet from maximum tension side of foundation
 Y

Z X

N86

N24
N28

N26 N88

N85 N105A N175 N176 N177

N87 N178 N179 N15

Paul J. Ford and Company SK - 1

Apr 8, 2019 at 12:52 PM
A00019-0067 00019-0067- ARE Ballast Foundati...
 Y

Z X

PL
5x
35

6
HSS2x2x3-A1085

4X
PL 5 x 35 E11
P
PI
C H_
LL_63X63X6X16

LL
_6
3X
63
X6
X1
6

LL_100X100X8X16

Paul J. Ford and Company SK - 2

Apr 8, 2019 at 12:53 PM
A00019-0067 00019-0067- ARE Ballast Foundati...
 Y

Z X

N86

N24
N28

N26 2.99k N88

N85 N105A N175 N176 N177

N87 N178 N179 N15

4.98k

9.46k
10.62k 10.77k
11.56k

Loads: BLC 1, BLC1

Paul J. Ford and Company SK - 3

Apr 8, 2019 at 12:54 PM
A00019-0067 00019-0067- ARE Ballast Foundati...
 Company : Paul J. Ford and Company Apr 8, 2019
Designer : 12:54 PM
Job Number : A00019-0067 Checked By:_____
Model Name :

(Global) Model Settings

Display Sections for Member Calcs 5
Max Internal Sections for Member Calcs 97
Include Shear Deformation? Yes
Increase Nailing Capacity for Wind? Yes
Include Warping? Yes
Trans Load Btwn Intersecting Wood Wall? Yes
Area Load Mesh (mm^2) 92903.412
Merge Tolerance (mm) 3.048
P-Delta Analysis Tolerance 0.50%
Include P-Delta for Walls? Yes
Automatically Iterate Stiffness for Walls? Yes
Max Iterations for Wall Stiffness 3
Gravity Acceleration (mm/sec^2) 9814.58
Wall Mesh Size (mm) 304.801
Eigensolution Convergence Tol. (1.E-) 4
Vertical Axis Y
Global Member Orientation Plane XZ
Static Solver Sparse Accelerated
Dynamic Solver Accelerated Solver

Hot Rolled Steel Code AISC 13th(360-05): LRFD

Adjust Stiffness? Yes(Iterative)
RISAConnection Code None
Cold Formed Steel Code None
Wood Code None
Wood Temperature < 100F
Concrete Code None
Masonry Code None
Aluminum Code None - Building

Number of Shear Regions 4

Region Spacing Increment (mm) 101.6
Biaxial Column Method Exact Integration
Parme Beta Factor (PCA) .65
Concrete Stress Block Rectangular
Use Cracked Sections? Yes
Use Cracked Sections Slab? Yes
Bad Framing Warnings? No
Unused Force Warnings? Yes
Min 1 Bar Diam. Spacing? No
Concrete Rebar Set REBAR_SET_ASTMA615
Min % Steel for Column 1
Max % Steel for Column 8

RISA-3D Version 15.0.4 [G:\...\...\...\...\...\RISA\00019-0067- ARE Ballast Foundation 1500 Series.r3d] Page 1
 Company : Paul J. Ford and Company Apr 8, 2019
Designer : 12:54 PM
Job Number : A00019-0067 Checked By:_____
Model Name :

(Global) Model Settings, Continued

Seismic Code ASCE 7-10
Seismic Base Elevation (mm) Not Entered
Add Base Weight? Yes
Ct X .049
Ct Z .049
T X (sec) Not Entered
T Z (sec) Not Entered
RX 3
RZ 3
Ct Exp. X .75
Ct Exp. Z .75
SD1 1
SDS 1
S1 1
TL (sec) 5
Risk Cat I or II
Drift Cat Other
Om Z 1
Om X 1
Cd Z 4
Cd X 4
Rho Z 1
Rho X 1

Joint Loads and Enforced Displacements (BLC 1 : BLC1)

Joint Label L,D,M Direction Magnitude[(k,k-ft), (in,rad), (k*s^2/...
1 N85 L Y 4.98
2 N105A L Y 10.62
3 N175 L Y 11.56
4 N176 L Y 10.77
5 N177 L Y 9.46
6 N178 L Y 0
7 N26 L Z 2.99

Member Primary Data

Label I Joint J Joint K Joint Rotate(de... Section/Shape Type Design List Material Design Rules
1 P14 N85 N86 CH_PIPE114X6 None None A500 Gr.42 Typical
2 LL14 N15 N85 180 LL_100X100X8X16 None None Q345-B Typical
3 M55 N87 N88 LL_63X63X6X16 None None Q345-B Typical
4 M56 N15 N88 LL_63X63X6X16 None None Q345-B Typical
5 M17 N85 N24 180 HSS2x2x3-A1085 None None A500 Gr.46 Typical
6 M6 N26 N88 PL 5 x 35 None None Q345-B Typical
7 M7 N28 N88 PL 5 x 35 None None Q345-B Typical

Hot Rolled Steel Properties

Label E [ksi] G [ksi] Nu Therm (\1E...Density[k/ft... Yield[ksi] Ry Fu[ksi] Rt
1 A36 Gr.36 29000 11154 .3 .65 .49 36 1.5 58 1.2
2 A572 Gr.50 29000 11154 .3 .65 .49 50 1.1 65 1.1
3 A992 29000 11154 .3 .65 .49 50 1.1 65 1.1
4 A500 Gr.42 29000 11154 .3 .65 .49 42 1.4 58 1.3
5 A500 Gr.46 29000 11154 .3 .65 .49 46 1.4 58 1.3
6 A53 Gr. B 29000 11154 .3 .65 .49 35 1.5 58 1.2
7 Q235-B 29000 11154 .3 .65 .49 34 1.5 58 1.2

RISA-3D Version 15.0.4 [G:\...\...\...\...\...\RISA\00019-0067- ARE Ballast Foundation 1500 Series.r3d] Page 2
 Company : Paul J. Ford and Company Apr 8, 2019
Designer : 12:54 PM
Job Number : A00019-0067 Checked By:_____
Model Name :

Hot Rolled Steel Properties (Continued)

Label E [ksi] G [ksi] Nu Therm (\1E...Density[k/ft... Yield[ksi] Ry Fu[ksi] Rt
8 Q345-B 29000 11154 .3 .65 .49 50 1.5 65 1.2

Member Section Forces

LC Member Label Sec Axial[k] y Shear[k] z Shear[k] Torque[k-ft] y-y Moment[k-ft] z-z Moment[k-ft]
1 1 P14 1 34.546 1.822 0 0 0 7.771
2 2 34.546 1.822 0 0 0 2.811
3 3 34.546 1.822 0 0 0 -2.149
4 4 52.86 -.582 0 0 0 -.824
5 5 52.86 -.582 0 0 0 .759
6 1 LL14 1 -24.966 -2.755 0 0 0 -2.695
7 2 -24.966 -2.755 0 0 0 3.038
8 3 -24.956 14.054 0 0 0 7.453
9 4 -24.956 3.453 0 0 0 -12.716
10 5 0 0 0 0 0 0
11 1 M55 1 26.546 0 0 0 0 0
12 2 26.546 0 0 0 0 0
13 3 26.546 0 0 0 0 0
14 4 26.546 0 0 0 0 0
15 5 26.546 0 0 0 0 0
16 1 M56 1 -25.05 0 0 0 0 0
17 2 -25.05 0 0 0 0 0
18 3 -25.05 0 0 0 0 0
19 4 -25.05 0 0 0 0 0
20 5 -25.05 0 0 0 0 0
21 1 M17 1 -.027 0 -.296 0 .925 0
22 2 -.027 0 -.296 0 .438 0
23 3 -.027 0 -.296 0 -.049 0
24 4 -.032 0 .051 0 -.066 0
25 5 0 0 0 0 0 0
26 1 M6 1 -3.336 0 0 0 0 0
27 2 -3.336 0 0 0 0 0
28 3 -3.336 0 0 0 0 0
29 4 -3.336 0 0 0 0 0
30 5 -3.336 0 0 0 0 0
31 1 M7 1 .06 0 0 0 0 0
32 2 .06 0 0 0 0 0
33 3 .06 0 0 0 0 0
34 4 .06 0 0 0 0 0
35 5 .06 0 0 0 0 0

Member AISC 13th(360-05): LRFD Steel Code Checks (By Combination)

LC Member Shape UC Max Loc[mm] Shear...Loc[... Dir phi*Pnc[k] phi*Pnt[k] phi*M...phi*M... Cb Eqn
1 1 P14 CH_PIPE114... .973 0 .051 0 75.106 119.289 13.466 13.466 2.4...H1-1a
2 1 LL14 LL_100X100... .984 1241.892 .275 229... y 129.022 218.178 23.425 9.418 1 H1-1b
3 1 M55 LL_63X63X6... .330 0 .000 0 y 80.501 101.695 7.796 4.416 1 H1-1a
4 1 M56 LL_63X63X6... .246 0 .000 0 y 59.437 101.695 7.796 4.416 1 H1-1a
5 1 M17 HSS2x2x3-A... .319 0 .022 0 z 23.736 52.578 2.901 2.901 1 H1-1b
6 1 M6 PL 5 x 35 - L/r > 300 for tensio...
7 1 M7 PL 5 x 35 - KL/r > 200 for comp...

RISA-3D Version 15.0.4 [G:\...\...\...\...\...\RISA\00019-0067- ARE Ballast Foundation 1500 Series.r3d] Page 3
 1 2 3 4 5 6 7 8
Proprietary rights are included in the information disclosed herein. This information is REVISIONS
submitted in confidence and neither the document nor the information disclosed here- REV. DESCRIPTION DATE APPROVED
A initial release 3/18/19 MGC
in shall be reproduced or transferred to other documents for manufacturing or for any 1. Load Data (Turbine Only) B Revised pole dia., RA web thickness & increased bolt dia. 4/4/19 MGC
other purpose except as specifically authorized in writing by ARE Telecom & Wind.
50 yr Extreme Load DEL "Fatigue" Fatigue (2x10^6 Cycles)
.39
A
10 Fx (kN) A

Flange 1. Fy (kN)
15.55 28.54 Fz (kN)
83.20 395 725
2113.20 My (kN-m)
(12x) 112mm x 118mm Mx (kN-m)
Handhole 24.61 Mz (kN-m)
221.06 4 1.54 625
86.60
5615 (16x) 39 BCD 2. Survival Wind Speed: 39.8 m/s (89 mph); (3 sec gust)
2200 • Structure Class - II
• Exposure Category - C
B B
• Topographic Category - 5 - Crest Height 2853ft
F1 Flange 2. 3. Design and Welding Codes:
86.60 40.55 • TIA-222-G
2200 1030 • Eurocode 3, 1-9
27.56 • AWS D1.1
1.57 700 • IEC 61400-2
40 4. Material
typ. 86.60 • Pole: ASTM A572 GR65 (or equivalent - Q420B)
2200 1.54 36.61 • Baseplate: ASTM A572 GR50 (or equivalent - Q345B)
(22x) 39 930 • Flange/ Plate: ASTM A572 GR50 (or equivalent - Q345B)
BCD • Standard Structural Members: A36 (or equivalent - Q235B)
C C
5. Deflection: < 2% @ 27m/s (60 mph)
Flange 3. 6. Pole has 12 sides (Section #4) and 18 sides (Sections #1 to #3)
1020.63 3
25924 354.33 7. Finish: Hot dip Galvanizing per ASTM A123
9000 37.40 8. Anchor Bolts: (44x) M33x3.5 x 300mm Full Thread - (3X) Nut, (4X) Washer
25.49
950 R647.50 Flange Bolts: (74x) M33x3.5 x 150mm - (1X) Nut, (2X) Washer
• Grade 8.8
• (Optional Grade) ASTM F1554 GR55 or A325
1.54
F2 (36X) 39 9. Pole Section Details
47.05
D 1195 Pole Section #1 #2 #3 #4 D
BCD Thickness (mm)/ (in) 10/ 0.375 10/ 0.375 8/ 0.314 6/ 0.25
Length (m)/ (ft) 1.720/ 5.64 7.09/ 23.26 8.92/ 29.27 5.56/ 18.26
(2X)Climbing Pegs Baseplate Top Dia. (mm)/ (in) 1042/ 41 800/ 31.5 497/ 19.6 307/ 12.1
Safety Cable
Both Sides 2 Bottom Dia. (mm)/ (in) 1084/ 42.7 1039/ 40.9 798/ 31.4 495/ 19.5
39.37 52.36 Min Slip (mm)/ (in) NA NA NA
1000 1330
Weight (kg)/ (lbs) 1130/ 2486 2390/ 5258 1390/ 3058 440/ 968
282.68
7180 1.54 10. Charpy V-Impact Requirements
Ram Bracket (36X) 39
E 48.43 Charpy-V Notch Test E
BCD 1230
(2X) 33 Ton
Material Min Impact Energy Test Temperature
Hydraulic (J) ( C)
F3 1.97
Cylinder
(2x) 50 ASTM A572 GR65 34 -30
Stroke - 60" (1524mm)
ASTM A572 GR50 21 -29
Q460B 42 20
1
1.97 71.65 Q345B 34 20
Cylinder Bracket 400mm x 800mm 1820
Handhole 50 Q235B 27 20
ARE Telecom & Wind

F
US Patent # 9428877 CAD-generated drawing 1043 Grand Ave., #213
St Paul, MN 55105
China Patent # ZL201490000869.X do not manually update (651) 330 1263
www.aretelecom.com

90.91
2309
Notes 1: Steel Weight APPROVALS
Pole 5750kg (12650lbs) DRAWN MGC
DATE
25.9m Hyd Pole
AFS1700
3/18/19
1. See manual for instruction on operating and maintaining the AFS1700 9245kg (20339lbs) CHECKED
Does not include fasteners
hydraulic raising/ lowering system. RESP ENG
CAD file :
MATERIAL See Notes Details and dimensions
MFG ENG not shown on this drawing
FINISH See Notes can be found in CAD file
1 2 3 4 5 DO NOT SCALE DRAWING rev. B size NA sheet 1 of 8
QUAL ENG scale NA
 1 2 3 4 5 6 7 8
Proprietary rights are included in the information disclosed herein. This information is
submitted in confidence and neither the document nor the information disclosed here-
in shall be reproduced or transferred to other documents for manufacturing or for any 277.56
other purpose except as specifically authorized in writing by ARE Telecom & Wind.
7050

A
A
Bearing Surface Area ADD LOOSE
3.75ft^2 (0.345m^2) FITTED
TAPEZIODAL
PLATES, 5mm
THK (18 PLACES)

B B

138.78
3525

C C

8.43
214
3.94 1.57
100 40

246.38
D
6258.09 D

249.58
6339.26

E E

86.97
2209 82.17
2087
Notes 2:
• Ballast Volume = 60 cu-m (78.5 cu-yds, 2120 cu-ft)
• Unit Weight
• cu-ft = 45.45 kg (100 lbs) F

F • cu-yd = 1227.3 kg (2700 lbs)

1043 Grand Ave., #213
• cu-m = 1605.5 kg (3532 lbs) St. Paul, MN 55105
(651) 330-1263
• The foundation design is based upon an ultimate bearing pressure www.aretelecom.com

of 8000 pounds per square ft (PSF) AFS1700

Part #
1 2 3 4 5 6 7
scale NA rev. A-1 size NA sheet 2 of 8
 1 2 3 4 5 6 7 8
Proprietary rights are included in the information disclosed herein. This information is REVISIONS
submitted in confidence and neither the document nor the information disclosed here- REV. DESCRIPTION DATE APPROVED
in shall be reproduced or transferred to other documents for manufacturing or for any A initial release 8/23/17 MGC
B Revised RA web thickness & bolt dia. 4/4/19 MGC
other purpose except as specifically authorized in writing by ARE Telecom & Wind.

Notes 3: AFS1700 Bill of Materials

A 1. All plate material shall shall have a minimum yield strength # DESCRIPTION QTY. Weight (kg/ lbs) A
of 345 MPa (50 ksi) 1 Kingpost 1 2014/ 4431
2. Tube shall be 114mm x 6mm GR. Q345 (4.5" x 0.25" ASTM A500 Gr B)
3. All right angles shall be Q345 (ASTM A572 Gr 50) or equivalent 2 Upper Chord round 114mm x 6mm (4.5" x 0.25") 18 81/ 178
4. All welding shall conform to the minimum requirements 3 Ballast Tray 18 121/ 266
of AWS D1.1 4 Vertical Web w/ Gusset Plate Assembly 18 15.5/ 34
5. All welding shall be done by welders qualified under AWS
specifications, using E80XX, low hydrogen electrodes 5 Diagonal Web 36 7.5/ 16.5
6. All components shall Hot Dip Galvanized in accordance with 6 M12 (1/2-13) Hinge Rod w/ (4x) Nuts and Washers 18 1.3/ 3
ASTM A123
B 7. Debur all sharp edges 7 Sidewall (hinged) 18 80/ 176
B
8 Vertical Hinge Post 18 15/ 33
1 17 9 Horizontal Brace 18 3.5/ 8
13
10 Diagonal Brace 18 3.9/ 9
11 Clevis & Cotter 12mm x 75mm (1/2" x 3") 18 0.1/ 0.22
12 Clevis & Cotter 12mm x 115mm (1/2" x 4.5") 72 0.14/ 0.31
13 Cylinder Bracket 1 193/ 345
6
14 Chord Bearing Plate 18 76/ 167
C C

2
10 15 7

15

15 9
15
D
D
5
8
15
3
11
4

15 16 16
16
E 16 12
E

16
16 14
16

AFS 1700 Bolts, Nuts & Washers (other equivalent grades acceptable)
# Unit Bolt Size Length Width Across Flats Thread Length Grade Coating Nut Qty. Washer Qty. Bolt Qty.
15 Metric M20x2.5 65mm 30mm Full Thread 8.8 Hot Dip Galv. 108 216 108 US Patent # 9428877
China Patent # ZL201490000869.X
15 Imperial 3/4-10 2.5" 1 1/8" Full Thread A325 Hot Dip Galv. 108 216 108 CAD-generated drawing ARE Telecom & Wind
F 413 Wacouta St. Suite #440
do not manually update
16 Metric M24x3 75mm 36mm Full Thread 8.8 Hot Dip Galv. 126 252 126 St Paul, MN 55101 (651) 330 1263

16 Imperial 1-8 3" 1-1/2" Full Thread A325 Hot Dip Galv. 126 252 126
Does not include anchor bolts,
templates or flange bolts
APPROVALS DATE AFS-1700
BOM
DRAWN
MGC 3/19/19

17 Metric M33x3.5 300mm 50mm 300mm 8.8 Hot Dip Galv. 176 176 44 CHECKED

RESP ENG
CAD file :
17 Imperial 1 1/4-7 12" 2" 12" A325 Hot Dip Galv. 176 176 44 MATERIAL See Notes
MFG ENG
Details and dimensions
not shown on this drawing
FINISH See Notes can be found in CAD file
1 2 3 4 5 DO NOT SCALE DRAWING rev. B size NA 3 of 8
QUAL ENG scale NA
 1 2 3 4 5 6 7 8
Proprietary rights are included in the information disclosed herein. This information is
submitted in confidence and neither the document nor the information disclosed here-
in shall be reproduced or transferred to other documents for manufacturing or for any
other purpose except as specifically authorized in writing by ARE Telecom & Wind.
13.78
350
A
A

23.23 1.57 5.51

590 40 140
1.57 5.51 9.84
40 TYP. 140 250

1.57
40 TYP.

7.87 17.85
200 453.42
B B
43.98 4.53
1117.06 115
87.60 18.05
2225 1.57
458.42
40 TYP. (3X) 6" sq. 1/2" Wall
4.33
110
.87
22
C
typ. C
8.81
223.76 .59
13.78 R15
350 typ.

1.18
CL 30
26.57
.47
62.01 12
3.39 675
1575 86
D
CL D

62.40
1585
150.00°

47.83
1215
14.89
378.11
E E

2.64
5.28 67
134 F

F
1043 Grand Ave., #213
St. Paul, MN 55105
(651) 330-1263
1.54 6.42 www.aretelecom.com
163
(8X) 39
AFS1700 Kingpost
CL
Part #
1 2 3 4 5 6 7
scale NA rev. A size NA sheet 4 of 8
 1 2 3 4 5 6 7 8
Proprietary rights are included in the information disclosed herein. This information is
submitted in confidence and neither the document nor the information disclosed here-
in shall be reproduced or transferred to other documents for manufacturing or for any
other purpose except as specifically authorized in writing by ARE Telecom & Wind.

A 4.22 A
107.20

.63
16
typ.

B B

1.60
114.66 40.66 .98
2912.34 25

114mm x 6mm wall CL

C C

120.08
3050
3.74
95
57.09
1450

8.98 83.78
D
228 .87 2128 D

(3x) 22

12.20 5.51
310 140

4.80
122
2.24
E 57 E

5.91 .59
150 R15 16.18
typ. 410.86 4.54
2.13
115.29
54
40.00°
2.76
1.18 70 F
4.33 30
F 110 1.18 1043 Grand Ave., #213
4.92 St. Paul, MN 55105
125 (2x) 30 (651) 330-1263
.55 www.aretelecom.com

14
1.38 27.36 AFS1700 Upper Chord
35 695
Part #
1 2 3 4 5 6 7
scale NA rev. A size NA sheet 5 of 8
 1 2 3 4 5 6 7 8
Proprietary rights are included in the information disclosed herein. This information is
submitted in confidence and neither the document nor the information disclosed here-
in shall be reproduced or transferred to other documents for manufacturing or for any
other purpose except as specifically authorized in writing by ARE Telecom & Wind.

A
A

96.93
2462.02

B B

41.77
1060.86

6.77 11.30
172 287 11.30
287 5mm Plate
9.33 Material Q345B
237 11.30 8.94
C 287 227 C

(5x) RA 60mm x 60mm x 6mm

Material Q345B

98.43
2500

D
D

(3x) RA 100mm x 100mm x 8mm

96.06
Material Q345B
2440
91.14
2315
E E
53.15
1350

45.28
1150
2.36
60
F

F
1.18 2.13
1043 Grand Ave., #213
St. Paul, MN 55105
(10x) 30 54 (651) 330-1263
www.aretelecom.com

AFS1700 Ballast Tray

Part #
1 2 3 4 5 6 7
scale NA rev. A size NA sheet 6 of 8
 1 2 3 4 5 6 7 8
Proprietary rights are included in the information disclosed herein. This information is
submitted in confidence and neither the document nor the information disclosed here-
in shall be reproduced or transferred to other documents for manufacturing or for any
other purpose except as specifically authorized in writing by ARE Telecom & Wind.

A
A

.24
6 2.48
2.48 63
63
.24
6

B 2.48 B
58.03 63
.63 1473.85
.24
16
6
2.48
63

1.57
40 1.14
C 29 C

.87 2x 1.14
(2x) 22 29 .24
1.57 6
40
.87
22
54.88
1393.85

D
36.22 D
920

40.86
1037.72

E E

1.18
8.03
30
204
typ.

9.65
245
F
1.77
F 45
3.94 1043 Grand Ave., #213
St. Paul, MN 55105
100 (651) 330-1263
www.aretelecom.com
All material shall be Q345B AFS1700 Vert./ Diag. Web
12.60
320
Part #
1 2 3 4 5 6 7
scale NA rev. B size NA sheet 7 of 8
 1 2 3 4 5 6 7 8
Proprietary rights are included in the information disclosed herein. This information is
submitted in confidence and neither the document nor the information disclosed here-
in shall be reproduced or transferred to other documents for manufacturing or for any
other purpose except as specifically authorized in writing by ARE Telecom & Wind.

A
A

13.78
350

8.90
226

B B

8.90 .47
226 12
typ.

.67
17
6.30
39.37 160
C 1000 .47
C

12
typ.

1.97
50

D
D

.47
12
typ.

4.17 6.30
106 160
E E
3.43 17.87
87 454
1.77 9.84 1.97
250 3.94 50
45
100
4.33 5.91
110 150

F
1.18 1043 Grand Ave., #213
St. Paul, MN 55105
(4x) 30 (651) 330-1263
www.aretelecom.com

Material is Q345B AFS1700 Chord

BearingPlate
Part #
1 2 3 4 5 6 7
scale NA rev. A size NA sheet 8 of 8