Scribd
Upload
236 views3 pages

Free Fall Calculations

The document provides calculations to determine the maximum submergence depth of a free fall lifeboat during launch. It uses an equation that takes into account the draft of the vessel, angle of fall, length of the lifeboat, added mass, and other parameters. Plugging in values for these parameters, it determines that the maximum submergence depth is 2.096m, which is less than the vessel's aft draft of 2.862m. Separate calculations are also shown to determine the axial added mass and its derivative used in the main equation.

Uploaded by

Kiran Kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
236 views3 pages

Free Fall Calculations

The document provides calculations to determine the maximum submergence depth of a free fall lifeboat during launch. It uses an equation that takes into account the draft of the vessel, angle of fall, length of the lifeboat, added mass, and other parameters. Plugging in values for these parameters, it determines that the maximum submergence depth is 2.096m, which is less than the vessel's aft draft of 2.862m. Separate calculations are also shown to determine the axial added mass and its derivative used in the main equation.

Uploaded by

Kiran Kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Calculations showing Maximum submergence of free fall life boat (refer DNV OS- E406 section 315)

An approximation for the maximum submersion depth of the lifeboat can be obtained by simple energy
considerations. The maximum submersion can be approximated by the formula

(1)

00 29-03-2019 IRS VENKI VEER RAJU KIRAN

REV DATE SUBMITED TO DRAWN CHECKED APPROVED

Vessel M V Rajeshree TITLE

OWNER KAN Enterprises


Free fall launching
calculations

NTS A4 MDES/01/kan/misc/ffb/1 1 OF 1
HD = 3.02 (the draft of the vessel is 2.862 in loaded departure condition)

Θ = 350
Lgo = 4.25 m

A’33,0 = 5195 kg/m (calculations shown separately in pg 3)

L = 6.5 m

M = 3800 kg

d1 = 3.25 m

ϕ = 370 (measured counter clockwise refer above figure)

V = 13 m3

ρ = 1025 kg/m3

Substituting the values in the above equation (1)

dmax = 2.096m (the maximum aft draft measure at fr 25 is 2.862m)

Pg 2
Added mass calculations:

Refer “Water Entry Simulation of Free-fall Lifeboat First Report : Analysis of Motion and Acceleration” by
Makoto Arai, M. Reaz H. Khondoker, Yoshiyuki Inoue-- Journal of The Society of Naval Architects of Japan,
Vol. 178

Here, m(l) is the axial added mass and dm/dl is its derivative, which depend on axial immersion l . The axial
immersion l and the distribution of axial added mass m(l) are :

max = κπρLD2/6 ……(2)

where

κ = 0.61

ρ = 1025 kg/cu.m

L = 6.5m

D = 2.72m

Therefore max = 15735.6

dm/dl at l = 0 ie differentiating eq (2) w .r .t l and substituting l =0 results

dm/dl = 5 max / 2L = 6052.15

d1 from Eq set (1) corresponds to l = L/2 i.e. differentiating m(l) wrt l from Eq set (2) and equating it to 0.

i.e. d1 = 3.25m

Pg 3

You might also like