Motor-operated Mechanisms

Types MT50; MT100 and MT50-3f; MT100-3f

for High-Voltage Disconnectors and Earthing Switches
for Outdoor Installation

Publication No. 1HPL 700 002a En

 Application
The motor-operated mechanisms type MT50; MT100 and The basic version of MT…includes the following:
MT50-3f; MT100-3f are designed for outdoor installation and used
for the electrical remote operation of disconnectors and earthing • Contactor control with lock-in feature
switches. • One changeover switch (local-off-remote) and two push
buttons (ON, OFF)
Design • 8-pole pilot switch with 4 NC and 4 NO contacts (by removing
the bridges and cancelling the series connection the number
of pilot switch contacts can be increased up to: 8 NC and 8
All components of the operating mechanism are assembled in
NO contacts).
an aluminium sheet housing with a door at the front. The control 2
components are attached to mounting plate and wired to the • Wiring TQ 1.5 mm flexible, black; except the motor lead
2
terminal strip. which is: Dipotherm 0.56 mm , coloured.
For connecting the control cables to the terminal strip is • In case of AC operation, a rectifier is installed upstream of the
provided a clearance of approx.10 cm. DC motor.
The connections to motor, to the limit switches, and (if • The incoming and outgoing cables are passed from below
included) the blocking magnet and the lighting system are routed through a 4-mm-thick removable cable entry plate made of
via an adapter plug. aluminium.
• The cable glands are not included in the standard scope of
20 29 3 2 10 13 1 19 27 delivery, and must be provided by the customer. All bored
holes (standard version: 2 x conduit thread P36, 4 x conduit
thread P29 and 2 x conduit thread P16) are closed with
blanking plugs. For ventilation is provided a cable gland with
a filter insert. It is located in the cable entry plate. In that plate
is also located the connection angle with 13-mm bored hole
for the earth coming in from outside.
• The earthing connection in the box between the door and the
2
housing has a cross-sectional area of 6 mm .
• An anti-condensation heater connected to the voltage supply
is permanently mounted onto the terminal unit.
• Device for locking the door - double-beard lock

Other options can be supplied on request.

All devices are protected against accidental touching of electrical
connections by means of appropriate constructional features or
covers.

20 29 3 2 10 13 1a 27

25 31 26 9 5 4 6 30 37 12

Operating mechanism type MT50 / MT100

1 DC motor (MT…)
1a 3-phase AC motor (MT…-3f)
2 Operating spindle
3 Pilot switch
4 Mounting plate
5 Terminal strip
6 Control contactor
9 Supply lead plate (with blanking plugs and earthing
connection angle)
10 Operating shaft
12 Housing
13 Control disc
19 Blocking magnet
20 Push button
25 Overload protection (optionally)
26 Flexible earthing connection 31 26 9 5 4 6 19 12
27 Adapter plug
29 Changeover switch
Operating mechanism type MT50-3f / MT100-3f
30 Push button for blocking magnet
31 Internal lamp (optionally)
37 Rectifier (when AC motor voltage is supplied)

HAPAM Poland Sp. z o.o. 2

 Additional options
1 Pilot switches (maximum of 2 pilot switches can be installed) 8 Internal lighting (switches on when door is opened)
1.1 -8-pole pilot switch 4NC and 4NO contacts (same 9 Device for locking the door:
design as included in basic version). 9.1 -handle type “T”
Switching capacity: 2 A at 220VDC, T=20ms. 9.2 -handle type “T” with cylinder lock
By removing the bridges and cancelling the series 9.3 -padlock with prevent removal of the cover for
installation the number of pilot switch contacts can be emergency operation
increased up to: 8NC and 8NO contacts. 10 Cable plate
In this case the switching capacity is: 10.1 -without holes
1 A at 220 VDC, T = 20 ms or 4 A at 110 VDC, T = 40ms
10.2 -with holes2xPg36, 4xPg29, 2xPg21 closed with
1.2 -8-pole pilot switch with 3NC, 3NO, 1 lagging NC, 1 blanking plugs
leading NO.
10.3 -as 10.1 but with cable glands
Switching capacity:
3NC, 3NO and 1 lagging NC contact: 11 Position indicator
2 A at 220 VDC, T = 20 ms or 4 A at 110 VDC. T = 40ms 11.1 -electrical (lamp)
By removing the bridges and cancelling the series 11.2 -mechanical
installation the number of pilot switch contacts can be
increased up to:
6NC, 6NO, 2 lagging NC, 1 lagging NC, 1 leading NO.
In this case the switching capacity is:
Mode of Operation
1 A at 220 VDC, T = 20 ms or4 A at 110 VDC, T = 40ms
Transmission of power from the motor to the operating spindle
1.3 -8-pole pilot switch with 3NC, 2NO, 1 lagging NC 1
is via a gear train. The motor is below the spindle and arranged
leading NO, 1 leading NO.
parallel to it, with a two-step gear train (for MT50; MT50-3f) or four-
Switching capacity:
step gear train (for MT100 and MT100-3f) between them.
3NC, 3NO, 1 lagging NC, 1 leading NO, contact:.
The motor operated mechanism is normally controlled from a
2 A at 220 VDC, T = 20 ms
control room or a local control cubicle, using an ON or OFF
By removing the bridges and cancelling the series
command. The control contactor picks up and locks in.
installation the number of pilot switch contacts can be
The switching angle of the output shaft is 190 degrees. When
increased up to:
either of the end positions is reached, a limit switch cancels the
6NC, 4NO, 2 lagging NC, 2 leading NO,
operation.
The switching capacity is:
Limit switches are tripped by the slide, which is moving along
1 A at 220 VDC, T = 20 ms or
the operating spindle.
4 A at 110 VDC, T = 40 ms
Auxiliary switches are actuated by control disc fitted to the
2 Wiring of the pilot switches to the terminal strip: operating shaft.
2.1 -wires with marks Unauthorised opening of the door and removing of cover hood
3 Local control system, consisting of: for manual emergency operation can be prevented by optionally
3.1 -one changeover switch (local-off-remote) and rest built-on padlock.
control switch (ON-OFF) The safety contacts interrupts the control circuit for the motor
4 Blocking magnet when the manual emergency crank is inserted, so that the unit can
5 Miniature circuit breaker for: now be operated only with the manual emergency crank.
5.1 -heater The optional blocking magnet prevents operation of the
5.2 -control system emergency manual operation of motor operated mechanism if
there is no actuating signal from the control room. In this case it is
5.3 -motor
not possible to insert the crank into the auxiliary pin for emergency
6 Motor protection device: operation.
6.1 -overload relay with automatic resetting
6.2 -overload relay with manual resetting
6.3 -overload circuit-breaker - automatic and manual reset
Little Maintenance
7 Control device for heating
The motor operating mechanism needs very little
7.1 -thermostat - adjusted
maintenance. Under normal climatic conditions the inspection
7.2 -hydrostat - adjusted intervals are every 5 years or 1000 operations.

Dimensions

dimension: A
M16; 30 depth

MT 50; MT100 500 hand crank

fixing thread

MT 50-3f; MT 100 -3f 650

HAPAM Poland Sp. z o.o. 3

 Technical data of motor operated mechanisms
Type MT50 MT50-3f
MT100 MT100-3f
Rated motor voltage 60,110,125 or 220 VDC; 3 x 230/400 VAC
110 or 230 VAC, 50/60 Hz
Admissible deviation from the rated motor voltage +10 / -20 % +10 / -10 %
Rated motor , short-time duty
input 660 W 750 W
output 470 W 560 W
Switching time (depending on load):
MT 50 3,5 - 6 sec. 6,5 - 9 sec.
MT 100 6,0 - 12 sec. 12 - 17 sec.
Max. torque required at the operating shaft for emergency
operation:
MT 50 5 Nm 3 Nm
MT 100 7.5 Nm 4 Nm
Rated torque on the operating shaft at rated voltage:
MT 50… 500 Nm 750 Nm
MT 100… 1000 Nm 1000 Nm
Rotations of emergence crank for a 190° switching angle of
the operating shaft:
MT 50… at least 100 at least 80
MT 100… at least 140 at least 110
Heating capacity approx. 25 W approx. 25 W
Heating voltage 60, 110, 125 or 230VAC 125; 230 VAC
Degree of protection against contact with live or moving parts
ingress of foreign bodies and water : IP 65 IP 65
2 2
Cross-section of internal wiring (except motor and heater) 1,5 mm 1,5 mm
Maximal cross-section of supply leads :
2 2
solid 4 mm 4 mm
2 2
stranded (with end sleeve) 2,5 mm 2,5 mm
Weight max. 40 kg max. 48 kg
Dimensions (cubicle) L x W x H 500 x 210 x 500 mm 650 x 500 x 210 mm
Technical data of the built-in control contactors
Operating voltage 60, 110, 125, or 220 VDC 110, 125 or 230 VAC
110 or 230 VAC
Admissible deviation from the operating voltage + 10 / - 15% + 10 / - 15%
Rated power consumption of the magnet coils
when operated with DC pick-up / holding 7W/7W 7W/7W
when operated with AC pick-up / holding 60VA / 9VA (50 W / 2,2 W) 60VA / 9VA (50 W / 2,2 W)
Min. Signal duration for self-holding 75 ms 75 ms
Technical data of the blocking magnet
Operating voltage 60, 110, 125, or 220 VDC
110 or 230 VAC
Admissible deviation from the operating voltage + 10 / - 15%
Rated power consumption of the magnet coil when operated approx. 6 W
with DC
Duty cycle 100 %

HAPAM Poland Sp. z o.o.

22/24 ks. bp. W Tymienieckiego Street
90-349 Lodz, POLAND
Tel. +48 42 663 54 50
Fax. +48 42 663 54 97
www.hapam.pl