Atkins

New Plan House Project Job no.

Epsom
Start page no./Revision
Calcs for
1
Calcs by Calcs date Checked Approved Approved
Checked by
R 12/04/2019 date by date
RC MEMBER DESIGN
In accordance with EN1992-1-1:2004 incorporating Corrigenda January 2008 and the UK national annex
Tedds calculation version 3.0.03
Concrete details - Table 3.1. Strength and deformation characteristics for concrete
Concrete strength class;
Aggregate type;
Aggregate adjustment factor - cl.3.1.3(2);
Characteristic compressive cylinder strength;
Characteristic compressive cube strength;
Mean value of compressive cylinder strength;
Mean value of axial tensile strength;
Secant modulus of elasticity of concrete; C35/45
Ultimate strain - Table 3.1; Quartzite
Shortening strain - Table 3.1; AAF = 1.0
Effective compression zone height factor; fck = 35 N/mm2
Effective strength factor; fck,cube = 45 N/mm2
Coefficient k1; fcm = fck + 8 N/mm2 = 43 N/mm2
Coefficient k2; fctm = 0.3 N/mm2  (fck/ 1 N/mm2)2/3 = 3.2 N/mm2
Coefficient k3; Ecm = 22 kN/mm2[fcm/10 N/mm2]0.3  AAF = 34077
Coefficient k4; N/mm2
Partial factor for concrete -Table 2.1N; cu2 = 0.0035
Compressive strength coefficient - cl.3.1.6(1); cu3 = 0.0035
Design compressive concrete strength - exp.3.15;  = 0.80
Compressive strength coefficient - cl.3.1.6(1);
 = 1.00
Design compressive concrete strength - exp.3.15;
k1 = 0.40
Maximum aggregate size;
k2 = 1.0  (0.6 + 0.0014 / cu2) = 1.00
Monolithic simple support moment factor;
k3 = 0.40
Reinforcement details
k4 = 1.0  (0.6 + 0.0014 / cu2) = 1.00
Characteristic yield strength of reinforcement;
Partial factor for reinforcing steel - Table 2.1N; C = 1.50
Design yield strength of reinforcement; cc = 0.85
Nominal cover to reinforcement fcd = cc  fck / C = 19.8 N/mm2
Nominal cover to top reinforcement; ccw = 1.00
Nominal cover to bottom reinforcement; fcwd = ccw  fck / C = 23.3 N/mm2
Nominal cover to side reinforcement; hagg = 20 mm
Fire resistance 1 = 0.25
Standard fire resistance period;
Number of sides exposed to fire;
Minimum width of beam - EN1992-1-2 Table 5.5;
Section 1
Rectangular section details
Section width;
Section depth;
fyk = 500 N/mm2
S = 1.15
fyd = fyk / S = 435 N/mm2
cnom_t = 35 mm
cnom_b = 35 mm
cnom_s = 35 mm
R = 60 min
3
bmin = 120 mm
b = 300 mm
h = 500 mm
PASS - Minimum dimensions for fire resistance met

Atkins
New Plan House Project Job no.
Epsom
 Start page no./Revision
Calcs for
2
Calcs by Calcs date Checked Approved Approved
Checked by
R 12/04/2019 date by date
300
500
3 × 16f
3 × 16f
2 × 8 legs @ 250 c/c
Positive moment - section 6.1
Design bending moment; M = Mpos_s1 = 100.0 kNm
Effective depth of tension reinforcement; d = 449 mm
Redistribution ratio;  = min(pos_s1, 1) = 1.000
K = M / (b  d2  fck) = 0.047
K' = (2    cc / C)  (1 -   ( - k1) / (2  k2))  (  ( - k1) / (2  k2))
= 0.207
K' > K - No compression reinforcement is required
z = min(0.5  d  [1 + (1 - 2  K / (  cc /
Lever arm; C))0.5], 0.95  d) = 427 mm
Depth of neutral axis; x = 2  (d - z) /  = 56 mm
Area of tension reinforcement required; As,req = M / (fyd  z) = 539 mm2
Tension reinforcement provided; 3  16f
Area of tension reinforcement provided; As,prov = 603 mm2
Minimum area of reinforcement - exp.9.1N; As,min = max(0.26  fctm / fyk, 0.0013)  b  d =
Maximum area of reinforcement - cl.9.2.1.1(3); 225 mm2
As,max = 0.04  b  h = 6000 mm2
PASS - Area of reinforcement provided is greater than area of
reinforcement required
Crack control - Section 7.3
wk = 0.3 mm
Maximum crack width;
Design value modulus of elasticity reinf – 3.2.7(4); Es = 200000
N/mm2
fct,eff = fctm = 3.2 N/mm2
kc = 0.4
k = min(max(1 + (300 mm - min(h, b))  0.35 /
500 mm, 0.65), 1) =
1.00
sbar = (b - (2  (cnom_s + fs1_v) + fs1_b_L1  Ns1_b_L1))
Mean value of concrete tensile strength;
/ (Ns1_b_L1 - 1) +
Stress distribution coefficient;
fs1_b_L1 = 99 mm
Non-uniform self-equilibrating stress coefficient;
s = 321 N/mm2
cr = Es / Ecm = 5.87
y = (b  h2 / 2 + As,prov  (cr - 1)  (h - d)) / (b 
h + As,prov  (cr - 1)) =
246 mm
Act = b  y = 73854 mm2
Actual tension bar spacing;
Maximum stress permitted - Table 7.3N;
Steel to concrete modulus of elast. ratio;
Distance of the Elastic NA from bottom of beam;
Area of concrete in the tensile zone;
Minimum area of reinforcement required - exp.7.1; Asc,min = kc  k
 fct,eff  Act / s = 296 mm2
PASS - Area of tension reinforcement provided exceeds
minimum required for crack control
Quasi-permanent moment; MQP = Mpos_QP_s1 = 65.0kNm

Atkins
New Plan House Project Job no.
Epsom
Start page no./Revision
Calcs for
3
Calcs by Calcs date Checked Approved Approved
Checked by
R 12/04/2019 date by date
Permanent load ratio; RPL = MQP / M = 0.65
Service stress in reinforcement; sr = fyd  As,req / As,prov  RPL = 253 N/mm2
Maximum bar spacing - Tables 7.3N; sbar,max = 184.2 mm
PASS - Maximum bar spacing exceeds actual bar spacing for crack control
Negative moment - section 6.1
Design bending moment; M = Mneg_s1 = 100.0 kNm
Effective depth of tension reinforcement; d = 449 mm
Redistribution ratio;  = min(neg_s1, 1) = 1.000
K = M / (b  d2  fck) = 0.047
K' = (2    cc / C)  (1 -   ( - k1) / (2  k2))  (  ( - k1) / (2  k2))
= 0.207
K' > K - No compression reinforcement is required
z = min(0.5  d  [1 + (1 - 2  K / (  cc /
Lever arm; C))0.5], 0.95  d) = 427 mm
Depth of neutral axis; x = 2  (d - z) /  = 56 mm
Area of tension reinforcement required; As,req = M / (fyd  z) = 539 mm2
Tension reinforcement provided; 3  16f
Area of tension reinforcement provided; As,prov = 603 mm2
Minimum area of reinforcement - exp.9.1N; As,min = max(0.26  fctm / fyk, 0.0013)  b  d =
Maximum area of reinforcement - cl.9.2.1.1(3); 225 mm2
As,max = 0.04  b  h = 6000 mm2
PASS - Area of reinforcement provided is greater than area of
reinforcement required
Crack control - Section 7.3
wk = 0.3 mm
Maximum crack width;
Design value modulus of elasticity reinf – 3.2.7(4); Es = 200000
N/mm2
fct,eff = fctm = 3.2 N/mm2
kc = 0.4
k = min(max(1 + (300 mm - min(h, b))  0.35 /
500 mm, 0.65), 1) =
1.00
sbar = (b - (2  (cnom_s + fs1_v) + fs1_t_L1  Ns1_t_L1))
Mean value of concrete tensile strength;
/ (Ns1_t_L1 - 1) + fs1_t_L1
Stress distribution coefficient; = 99 mm
Non-uniform self-equilibrating stress coefficient;
s = 321 N/mm2
cr = Es / Ecm = 5.87
y = (b  h2 / 2 + As,prov  (cr - 1)  (h - d)) / (b 
h + As,prov  (cr - 1)) =
246 mm
Act = b  y = 73854 mm2
Actual tension bar spacing;
Maximum stress permitted - Table 7.3N;
Steel to concrete modulus of elast. ratio;
Distance of the Elastic NA from bottom of beam;
Area of concrete in the tensile zone;
Minimum area of reinforcement required - exp.7.1; Asc,min = kc  k
 fct,eff  Act / s = 296 mm2
PASS - Area of tension reinforcement provided exceeds
minimum required for crack control
Quasi-permanent moment; MQP = Mneg_QP_s1 = 0.0kNm
Permanent load ratio; RPL = MQP / M = 0.00
Service stress in reinforcement; sr = fyd  As,req / As,prov  RPL = 0 N/mm2
Maximum bar spacing - Tables 7.3N; sbar,max = 300 mm
PASS - Maximum bar spacing exceeds actual bar spacing for
crack control
stop = (b - (2  (cnom_s + fs1_v) + fs1_t_L1  Ns1_t_L1))
/ (Ns1_t_L1 - 1) = 83.0
mm
Minimum bar spacing (Section 8.2)
stop,min = max(fs1_t_L1  ks1, hagg + ks2, 20mm) =
Top bar spacing;
25.0 mm
PASS - Actual bar spacing exceeds minimum
allowable
 Minimum allowable top bar spacing;

Atkins
New Plan House Project Job no.
Epsom
Start page no./Revision
Calcs for
4
Calcs by Calcs date Checked Approved Approved
Checked by
R 12/04/2019 date by date
Bottom bar spacing; sbot = (b - (2  (cnom_s + fs1_v) + fs1_b_L1  Ns1_b_L1)) / (Ns1_b_L1 - 1) = 83.0
mm
Minimum allowable bottom bar spacing; sbot,min = max(fs1_b_L1  ks1, hagg + ks2, 20mm) = 25.0 mm
PASS - Actual bar spacing exceeds minimum allowable
Section in shear (section 6.2)
max = 45 deg
Angle of comp. shear strut for maximum shear; v1 = 0.6  (1 - fck / 250 N/mm2) = 0.516
Strength reduction factor - cl.6.2.3(3); cw = 1.00
Compression chord coefficient - cl.6.2.3(3); Asv,min = 0.08 N/mm2  b  (fck / 1 N/mm2)0.5 /
Minimum area of shear reinforcement - exp.9.5N; fyk = 284 mm2/m
Design shear force at support ; VEd,max = VEd,max_s1 = 50 kN
Min lever arm in shear zone; z = 427 mm
Maximum design shear resistance - exp.6.9; VRd,max = cw  b  z  v1  fcwd / (cot(max) +
tan(max)) = 770 kN
PASS - Design shear force at support is less than maximum
design shear resistance
VEd = 50 kN
vEd = VEd / (b  z) = 0.391 N/mm2
 = min(max(0.5  Asin[min(2  vEd / (cw  fcd
Design shear force ;  v1),1)], 21.8 deg),
Design shear stress; 45deg) = 21.8 deg
Angle of concrete compression strut - cl.6.2.3; Asv,des = vEd  b / (fyd  cot()) = 108 mm2/m
Asv,req = max(Asv,min, Asv,des) = 284 mm2/m
2  8 legs @ 250 c/c
Asv,prov = 402 mm2/m
Area of shear reinforcement required - exp.6.8;
Area of shear reinforcement required;
Shear reinforcement provided;
Area of shear reinforcement provided;
PASS - Area of shear reinforcement provided exceeds
minimum required
Maximum longitudinal spacing - exp.9.6N; svl,max = 0.75  d = 337 mm
PASS - Longitudinal spacing of shear reinforcement provided is less than maximum