The IMPRESSA S9 One Touch Classic Manual: For Your Safety: Read and Understand Manual Before Use

Figure: Your machine may look
different to the one shown.
The IMPRESSA S9 One Touch Classic Manual
KE For your safety: read and understand manual before use.

Table of contents
Your IMPRESSA S9 One Touch Classic
IMPORTANT SAFEGUARDS 4
Control elements 8
1 IMPRESSA S9 One Touch Classic 10
JURA on the Internet......................................................................................................................................11
2 Preparing and using for the first time 12
Setting up.......................................................................................................................................................12
Filling the water tank....................................................................................................................................12
Bean container filling....................................................................................................................................12
First-time use.................................................................................................................................................13
Using and activating filter...........................................................................................................................14
Determining and adjusting the degree of water hardness...................................................................16
Adjusting grinder..........................................................................................................................................17
Switching on..................................................................................................................................................17
Switching off (standby)................................................................................................................................18
3 Familiarizing yourself with the control options 19
Preparation at the touch of a button........................................................................................................20
One-off settings before and during preparation....................................................................................20
Entering a permanent setting for the amount of water for a cup size...............................................21
Permanent settings in programming mode........................................................................................... 22
Viewing information and maintenance status.......................................................................................24
4 Preparation at the touch of a button 25
Espresso.........................................................................................................................................................25
Coffee.............................................................................................................................................................26
Coffee à la Carte...........................................................................................................................................26
Cappuccino................................................................................................................................................... 27
Latte macchiato............................................................................................................................................ 27
Pre-ground coffee........................................................................................................................................28
Hot milk and milk foam..............................................................................................................................29
Hot water ......................................................................................................................................................30
5 Permanent settings in programming mode 31
Products..........................................................................................................................................................31
Energy-saving mode (Energy Save Mode, E.S.M.©)............................................................................... 33
Time and weekday.......................................................................................................................................34
Programmable switch-on and switch-off time.......................................................................................35
Automatic switch-off...................................................................................................................................36
Rinses............................................................................................................................................................. 37
Unit amount of water / time format.........................................................................................................38
Language.......................................................................................................................................................39
6 Maintenance 40
Maintenance tips..........................................................................................................................................40
Rinsing the machine.....................................................................................................................................41
Changing the filter........................................................................................................................................41
2
Table of contents
Cleaning the machine.................................................................................................................................43

Descaling the machine................................................................................................................................45
Rinsing the cappuccino frother.................................................................................................................48
Cleaning the cappuccino frother...............................................................................................................49
Disassembling and rinsing the Professional Cappuccino Frother.......................................................50
Cleaning the bean container.......................................................................................................................51
Descaling the water tank.............................................................................................................................51
7 Display messages 52
8 Troubleshooting 54
9 Transport and environmentally neutral disposal 56
Transport / Emptying the system..............................................................................................................56
Disposal..........................................................................................................................................................56
10 Technical data 57
Index 58
JURA contact details / Legal information 60
Symbol description
Warnings
This is the safety alert symbol. lt is used to alert you to potential personal injury
J hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
J DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
J WARNING WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
J CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous situation
which, if not avoided, could result in minor or moderate injury.
NOTICE NOTICE is used to address practices not related to personal injury.
Symbols used
T Prompt to take action. This symbol means that you are being prompted to
perform some action.
E Information and tips to make it even easier to use your IMPRESSA.
COFFEE Display message
3

IMPORTANT SAFEGUARDS
Follow the basic safety When using electrical appliances, basic safety precautions shall
precautions always be followed, to reduce the risk of fire, electric shock, and/or
injury to persons, including the following:
ZZ Read all instructions.
ZZ Do not touch hot surfaces. Use handles or knobs.
ZZ To protect against fire, electric shock and injury to persons, do
not immerse power cord, plugs, or body of machine in water
or other liquid.
ZZ Close supervision is necessary when any appliance is used by
or near children.
ZZ Unplug from outlet when not in use and before cleaning.
Allow to cool before putting on or taking off parts, and before
cleaning the appliance.
ZZ Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or has been damaged in any
manner. Return appliance to the nearest authorized service
facility for examination, repair or adjustment.
ZZ The use of an accessory attachment not recommended by the
appliance manufacturer may result in fire, electric shock, or
injury to persons.
ZZ Do not use outdoors.
ZZ Do not let the cord hang over the edge of a table or counter,
or touch hot surfaces.
ZZ Do not place on or near a hot gas or electric burner, or in a
heated oven.
ZZ Always attach plug to appliance first, then plug cord into the
wall outlet. To disconnect, turn any control to ‘OFF’ then
remove plug from wall outlet.
ZZ Do not use appliance for other than intended use.
ZZ Use extreme caution when dispensing hot steam, hot water
or hot coffee.
ZZ For household use only.
SAVE THESE INSTRUCTIONS.

Pass them on to any subsequent user.
4

Intended use The appliance is designed and intended for household use only. It
shall only be used for coffee preparation and to heat milk and water,
according to these instructions. Use for any other purpose will be
deemed improper. JURA Elektroapparate AG cannot accept any
responsibility for the consequences of improper use.
People, including children, who

ZZ do not have the physical, sensory or mental capabilities to use
the appliance safely or
ZZ are inexperienced or lack knowledge in how to use the appli-
ance safely
must be supervised by a responsible person when using it, or must
be instructed in how to use it correctly.
Special power cord set ZZ The power cord is provided to reduce the risk resulting from
instructions becoming entangled in or tripping over a long cord.
ZZ The cord shall be arranged so that it will not drape over the
counter top or table top where it can be pulled on by children
or tripped over.
ZZ This appliance has a 3-pin grounded plug. As a safety feature,
this plug will fit in a polarized outlet only one way.
ZZ If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician.
ZZ Do not modify the plug in any way or attempt to defeat this
safety feature.
Do NOT use extension cords.

If the user chooses to use an extension cord,
ZZ the marked electrical rating of the extension cord shall be at
least as great as the electrical rating of the appliance, and
ZZ if the appliance is of the grounded type, the extension cord
shall be a grounding type 3-wire cord, and
ZZ the longer cord shall be arranged so that it will not drape over
the counter top or tabletop where it can be pulled on by chil-
dren or tripped over.
J WARNING To reduce the risk of fire or electric shock, DO NOT remove any ser-
vice covers. DO NOT modify the appliance in any way that is not
described in these instructions. NO user serviceable parts included.
Repair MUST be done by authorized personnel only.
5

In the event of signs of damage, for example if there is a smell of

burning, unplug the machine immediately from outlet and contact
JURA customer service.
J CAUTION This appliance is for household use. Any servicing other than clean-
ing and user maintenance shall be performed by an authorized ser-
vice representative:
ZZ Do not immerse base in water or try to disassemble.
ZZ Do not put the appliance or any individual parts in the dish-
washer.
ZZ Check voltage to be sure that the voltage indicated on the
name plate complies with your voltage.
ZZ Never use warm or hot water to fill the water container. Use
cold water only.
ZZ Keep your hands and the cord away from hot parts of the
appliance during operation.
There is a risk of scalds or burns on the spouts and the cappuccino

frother / nozzle.
ZZ Keep children away.
ZZ Do not touch any hot parts. Use the handles or knobs pro-
vided.
ZZ Ensure that the cappuccino frother / nozzle is correctly fitted
and clean. If incorrectly fitted or if they become blocked, the
cappuccino frother or its parts might come off.
NOTICE ZZ Never clean with scouring powders or hard implements.

ZZ Ensure that the ventilation slots are not covered.
ZZ Never pull out the drip tray during the brewing process. Only
pull the drip tray when the display instructs you or when the
appliance is ready for use.
NEVER DO ZZ Never fill instant coffee, chocolate mix etc. into the bean con-
(or you will void your tainer or ground coffee funnel (filler funnel for ground coffee).
warranty protection): It will damage the functioning of the brewing chamber.
ZZ Never fill sugar coated coffee beans into the bean container.
In case of doubt, call your dealer.
ZZ Never fill anything other than coffee beans into the bean con-
tainer (no chocolate, no rice, no nuts, no spices, nothing other
than roasted coffee beans).
6

ZZ Never fill frozen beans into the bean container. If you store
beans in the freezer, let them thaw 3 to 4 hours before filling
them into the bean container.
ZZ Never fill anything but fresh, cold and clean water into the
water tank, except when decalcifying.
ZZ Never use mineral or carbonated water. You can use tap water,
bottled water, spring water and reverse osmosis water.
ZZ Never do anything with the machine which is not described in
these instructions. In case of doubt, call your dealer.
7
Control elements
Control elements
9
2
10
11
3
12
J HOT
4
13
J HOT
J HOT 14
7
Figure: Your machine may look different to the one shown.
1 Bean container cover 8 Fineness of grind switch

2 Bean container with aroma preservation 9 Cup tray
cover 10 Cover of filler funnel for pre-ground coffee
3 Water tank with handle 11 Filler funnel for pre-ground coffee
4 Power switch and power cord 12 Professional Cappuccino Frother
(back of machine) 13 Height-adjustable coffee spout
5 Coffee grounds container 14 Hot water spout
6 Drip tray
7 Cup platform
8
Control elements
1 4
Front left Front right

1 Display 4 ö Selector switch
2 Rotary Switch cover a Hot water portion symbol
3 f Rotary switch m Hot water symbol
Q On/off button p Cappuccino button
c Maintenance button z Milk portion symbol
i 1 Espresso button n Milk symbol
4 2 Espressi button q Latte Macchiato button
o 1 Coffee button 5 Professional Cappuccino Frother
d 2 Coffees button
e Coffee à la Carte button
v Pre-ground coffee button
9
1 IMPRESSA S9 One Touch Classic

Coffee that fulfils your With the new flagship of the IMPRESSA S range, cappuccino and
wildest dreams latte macchiato are prepared at the touch of a button without you
having to move the cup. With its elegant platinum styling and
upgraded design, this high-quality product is fully in keeping with
contemporary trends and exudes superiority, solidity and compe-
tence. It impressively demonstrates these attributes with each
coffee specialty that you enjoy.
ZZ One Touch Cappuccino/Latte macchiato: Your IMPRESSA S9

makes a cup of cappuccino at the touch of a button, without
you having to move the cup. Hot milk foam, flowing into the
cup and slowly starting to fill it. Steam which rises, awakening
the anticipation of a delicious specialty. Aromatic coffee,
blending with the milk, pushing up the milk foam topping.
These are the protagonists in a sensuous drama – the drama
of perfect coffee preparation. A latte macchiato can also be
made equally easily and sensuously at the touch of a button.
ZZ Energy-saving mode (Energy Save Mode, E.S.M.©): The

IMPRESSA S9 One Touch Classic actively assists you in saving
energy. With the various stages of the energy-saving mode,
you can adjust the energy-saving potential to suit the way you
like to enjoy your beverages. The machine can be completely
disconnected from the power grid at the main switch – for
instance if you are going to be absent for some time.
ZZ Control philosophy: You can ‘navigate’ reliably through all

operating and programming steps simply by turning and
pressing the switch. The information on the plain text and
graphic display is in full view at all times. The focus is on your
personal taste. Simply select the coffee strength, amount of
water and temperature according to your individual prefe
rences.
10
ZZ Professional technology for the home: The active bean mon-

itoring feature of your IMPRESSA S9 banishes the sound of
empty rotating coffee grinders and the inconvenience of
half-full cups once and for all. It always shows you in good
time when the coffee beans need replenishing. The filling level
of the 10 oz (280 g) bean container is continuously optically
monitored.
JURA on the Internet Visit us on the Internet.
@@ At www.jura.com you will find interesting and up-to-date

information on your IMPRESSA and on every aspect of coffee.
11
2 Preparing and using for the first time

This chapter provides you with the information you need to use your
IMPRESSA without any problems. You will prepare your IMPRESSA
step-by-step for your first coffee experience.
Setting up When setting up your IMPRESSA, please note the following:

ZZ Set the IMPRESSA down on a horizontal surface that is not
sensitive to water.
ZZ Choose a spot for your IMPRESSA which is protected against
overheating.
Filling the water tank To enjoy perfect coffee we recommend changing the water every
day.
NOTICE Milk, sparkling mineral water or other liquids can damage the water
tank or the machine.
T Only fill the water tank with fresh, cold water.
TT Remove the water tank and rinse it with cold water.

TT Fill the water tank with fresh, cold water and reinsert.
Bean container filling The bean container has an aroma preservation cover. This will ensure
that your coffee beans retain their aroma for longer.
NOTICE Coffee beans which have been treated with additives (e.g. sugar),
ground coffee or freeze-dried coffee will damage the grinder.
T Only use untreated coffee beans to fill the bean container.
TT Open the cover of the bean container and remove the aroma
preservation cover.
TT Remove any dirt or foreign objects inside the bean con
tainer.
TT Fill the bean container with coffee beans, then close the
aroma preservation cover and the bean container cover.
12
First-time use
J WARNING If the machine is operated with a defective power cord, there is a
danger of potentially fatal electric shock.
T Never use a machine which is damaged.
T Never use a machine which has a defective power cord.
EE The water volume is given as standard in ‘oz’. You can change

this setting to ‘ml’ in programming mode (see Chapter 4 ‘Per-
manent settings in programming mode – Unit for amount of
water’).
Precondition: The water tank and bean container are full.

TT Insert the power plug into a power socket.
3 T Switch on the IMPRESSA using the power switch on the back
of the machine.
The on/off button Q lights up (standby).
Q T Press the on/off button to switch the IMPRESSA on.
The pre-set language appears on the display.
TT Open the cover of the Rotary Switch.

g T Turn the Rotary Switch until the desired language is dis-
played. For Example: LANGUAGE ENGLISH
k T Press the Rotary Switch to confirm the language.
CONFIRMED √ appears briefly on the display to confirm
the setting.
TIME --:--
g T Turn the Rotary Switch to set the hour.
TIME 12:00 (example)
k T Press the Rotary Switch to confirm the hour setting.
TIME 12:00
g T Turn the Rotary Switch to set the minutes.
TIME 12:45 (example)
k T Press the Rotary Switch to confirm the minute setting.
CONFIRMED √ appears briefly on the display.
WEEKDAY MONDAY
g T Turn the Rotary Switch to set the weekday.
WEEKDAY WEDNESDAY (example)
13
k T Press the Rotary Switch to confirm the setting.

FILL SYSTEM / PRESS RINSE, the maintenance
button c lights up.
TT Place a receptacle under the hot water spout and another
under the frother.
c T Press the maintenance button.
SYSTEM FILLS, the system fills up with water and the
maintenance button flashes. A small amount of water flows
from the frother and the hot water spout.
This operation stops automatically. WELCOME TO JURA
appears on the display.
HEATING UP
PRESS RINSE, the maintenance button c lights up.
TT Place a receptacle under the coffee spout.
The machine rinses itself, stopping automatically.
COFFEE READY appears on the display. Your IMPRESSA
is ready to use.
EE After first-time use do not disconnect the IMPRESSA from the

power grid for 24 hours to ensure that it is in the optimum
operating condition.
EE When a coffee specialty has been prepared for the first time,
it is possible that FILL BEANS is shown on the display as
the grinder has not yet been completely filled with coffee
beans. In this case prepare a different coffee specialty.
EE If you have not been able to use the machine for the first time
correctly and fully, contact customer support in your country
(see ‘JURA contact details / Legal information’).
Using and Your IMPRESSA no longer has to be descaled if you are using
activating filter CLEARYL filter cartridges.
EE Perform the ‘Insert filter’ operation without interruptions. This

will ensure that your IMPRESSA always produces its best.
Precondition: COFFEE READY is displayed.

14
k T Keep the Rotary Switch pressed until MAINTENANCE

g T Turn the Rotary Switch until FILTER NO is displayed.
k T Press the Rotary Switch to enter the program item.
FILTER NO
g T Turn the Rotary Switch until FILTER YES is displayed.
CONFIRMED w appears briefly on the display to confirm
the setting.
INSERT FILTER / PRESS RINSE, the maintenance
button c lights up.
TT Remove a CLEARYL filter cartridge and the filter cartridge
extension from the Welcome Pack.
TT Fit the extension on top of the filter cartridge.
TT Remove the water tank and empty it.
TT Lift the cartridge holder and insert the filter cartridge into
the water tank, applying slight pressure.
TT Close the cartridge holder. It will click into place audibly.
TT Place a receptacle (at least 17 oz or 500 ml) under the frother.
EE If you are using the Professional Cappuccino Frother, set the

selection lever of the frother to the steam position n.

FILTER RINSING, water flows out of the frother.
EE You can interrupt rinsing of the filter at any time by pressing

any button.
EE The water may be slightly discolored. This is not harmful to
health and does not affect the taste.
Filter rinsing stops automatically after approx. 17 oz (500 ml).

COFFEE READY appears on the display. The filter is now
activated.
15
Determining and The harder the water is, the more frequently the IMPRESSA needs to
adjusting the degree be descaled. It is therefore important to adjust the water hardness.
of water hardness
The water hardness can be adjusted on a continuous scale between
1° dH and 30° dH.
Level Display German Degrees of general Parts per Indicator Strip number
Degree (°dH) hardness (°dGH) million (ppm) of ‘reddish’ fields
Not active – – – –
Very soft water <3 <3 < 53.4 None
Soft water >4 >4 > 71 1
Hard water > 8.4 > 8.4 > 150 2
Very hard water > 14 > 14 > 250 3
EE However, if you are using the CLEARYL filter cartridge and have
activated it, you will not be able to adjust the water h
ardness.
You can find out what the water hardness is by using the Aquadur®
test strip supplied as standard.
TT Hold the test strip briefly (for one second) under flowing
water. Shake off the water.
TT Wait for about one minute.
TT You will then be able to read the degree of water hardness
from the discoloration of the Aquadur® test strip and the
description on the packaging.
You can now adjust the water hardness.
Example: To change the water hardness from 16°dH to 25°dH,

proceed as follows:
appears.
g T Turn the rotary switch until HARDNESS 16°dH is
displayed.
16°dH
g T Turn the Rotary Switch until 25°dH is displayed.
16

CONFIRMED w appears briefly on the display.
HARDNESS 25°dH
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY is shown on the display.
Adjusting grinder You can adjust the grinder continuously to suit the roast of your
coffee.
NOTICE If you adjust the consistency of grind when the grinder is not oper-
ating, the grinder adjustment switch could be damaged.
T Only adjust the consistency of grind when the grinder is run-
ning.
The consistency of grind setting is correct if the coffee flows regu-

larly from the coffee spout. In addition a fine, thick crema forms.
Example: To change the fineness of grind during coffee preparation,

proceed as follows:
TT Open the cover of the bean container.
TT Place a cup under the coffee spout.
o T Press the 1 Coffee button.
The grinder starts and 1 COFFEE is displayed.
TT Turn the fineness of grind switch to the desired position
while the grinder is running.
The coffee will be prepared and the fineness of grind is
adjusted.
Switching on When the IMPRESSA is switched on, a prompt for the rinse operation
automatically appears which is initiated by pressing the mainte-
nance button.
This setting can be changed in programming mode so that the

machine automatically activates the switch-on rinse (see Chapter 5
‘Permanent settings in programming mode – Rinses’).
Precondition: Your IMPRESSA is switched on at the power switch
and the on/off button Q is illuminated (standby).
17
Q T Press the on/off button to switch the IMPRESSA on.

WELCOME TO JURA appears briefly on the display.
HEATING UP
The machine rinses itself, stopping automatically.
is ready to use.
Switching off (standby) When you switch your IMPRESSA off, the spouts with which a coffee
specialty or milk have been prepared are rinsed.
TT Place a receptacle under the coffee spout and the frother.

Q T Press the on/off button.
MACHINE RINSING appears on the display, and the
coffee spout is rinsed.
SPOUT RIGHT / PRESS RINSE.
MACHINE RINSING, the right coffee spout is rinsed.
EE When you prepare a milk product, but have not performed

cappuccino cleaning, CLEAN CAPPUCCINO appears and
the maintenance button c lights up. For ten seconds you can
start the ‘Clean cappuccino frother’ procedure by pressing the
maintenance button c.
The IMPRESSA is switched off (standby mode), and the

on/off button Q lights up.
EE When your IMPRESSA is switched off, a hissing noise may be

audible. This is normal and does not have any effect on the
machine.
18
3 Familiarizing yourself with the control options

J WARNING Hot coffee, hot steam and hot water can cause scalding. Scalding is
a serious burn.
T Use extreme care when handling hot liquid or steam.
T Allow liquid to cool down before drinking.
T In the event of scalding, rinse affected area with cold water
and seek medical attention.
T Keep children AWAY.
With the IMPRESSA, you can prepare an excellent coffee or milk spe-
cialty at the touch of a button. You also have the option of adjusting
the coffee strength and temperature, as well as the amount of water
to your personal taste.
This chapter will allow you to become familiar with all control
options with the aid of examples. To familiarize yourself with your
IMPRESSA, we recommend that you make a point of actively trying
the facilities described in this chapter. You will find this is well worth-
while.
Learn how to perform the following:

ZZ Preparation at the touch of a button
ZZ One-off settings before and while your drink is being prepared
ZZ Adjusting the default amount of water to suit the cup size
ZZ Permanent settings in programming mode
EE You can stop the machine at any time while a coffee or milk
specialty or hot water is being prepared. To do this, press any
button.
water’).
19
Preparation at the Prepare your favourite coffee specialty at the touch of a button.
touch of a button
All coffee specialties are prepared following this model.
Example: This is how to prepare one coffee.

1 COFFEE and the pre-set coffee strength is displayed.
The pre-set amount of water flows into the cup. Preparation
stops automatically. ENJOY appears on the display.
OFFEE READY is then displayed.
C
EE To prepare 2 coffees, place two cups under the coffee spout

and press the 2 Coffees button d.
One-off settings before It is possible to make various settings before and during preparation.
and during preparation These one-off settings are always follow the same model and are not
stored.
Changing the coffee The coffee strength of Coffee à la Carte can be changed before
strength before preparation preparation. The following coffee strength options can be selected:
ZZ ö (xmild)
ZZ öö (mild)
ZZ ööö (normal)
ZZ öööö (strong)
ZZ ööööö (xstrong)
Example: Proceed as follows to to prepare a strong cup of Coffee à

la Carte.
e T Press the Coffee à la Carte button.
A LA CARTE and the pre-set coffee strength is displayed.
g T Turn the Rotary Switch until A LA CARTE öööö is
displayed.
k T Turn the Rotary Switch while A LA CARTE öööö is
displayed.
A LA CARTE öööö, the pre-set amount of water flows
into the cup. Preparation stops automatically. ENJOY
20
appears on the display. COFFEE READY is then dis-

played.
Changing the amount of The pre-set amount of water of all coffee products can be changed
water during preparation during the brewing operation by turning the Rotary Switch.
Example: Proceed as follows to prepare a 110 ML cup of coffee.

1 COFFEE and the pre-set coffee strength is displayed.
The brewing operation starts and the coffee flows into the
cup.
g T Turn the Rotary Switch during the brewing operation until
1 COFFEE / 110 ML is displayed.
The set amount of water flows into the cup. Preparation
C
Entering a permanent It is easy to make permanent settings for the amount of water for all
setting for the amount coffee specialties, cappuccino, latte macchiato, a portion of hot
of water for a cup size water and portion of milk according to the cup size. As in the follow-
ing example, adjust the amount of water once. Every time you pre-
pare a drink in the future, this amount of water will be dispensed.
Making the permanent settings for the amount of water for the
respective cup size always follows this model.
Example: To make permanent settings for the amount of water for

an espresso, proceed as follows:
TT Place an espresso cup under the coffee spout.
i T Press and hold the 1 Espresso button.
1 ESPRESSO and the coffee strength is displayed.
i T Hold the Espresso button down until ENOUGH COFFEE?
appears.
i T Release the 1 Espresso button.
Coffee preparation will start and the espresso will flow into
the cup.
21
TT Press any button as soon as enough espresso has flowed

into the cup.
Preparation stops automatically. CONFIRMED w appears
briefly on the display. The set amount of water for an espres-
so will be permanently stored. COFFEE READY is then
displayed.
EE You can alter these settings at any time by repeating the

above procedure.
Permanent settings in You can easily adjust your IMPRESSA to your personal coffee blends
programming mode and specialties. You can navigate through the easy-to-understand
program steps and make permanent settings simply by turning and
pressing the Rotary Switch.
You can make the following permanent settings with the Rotary
Switch:
Program item Subitem Explanation
MAINTENANCE CLEAN CAPPUCCINO, TT Select the desired maintenance program.
RINSE MACHINE, If no action is taken, programming mode
RINSE CAPPUCCINO, is exited in the MAINTENANCE program
CLEAN MACHINE, item automatically after approx. five seconds.
DECALCIFY MACHINE,
CHANGE FILTER
PRODUCTS TT Select your settings for the coffee and milk
specialties and hot water.
FILTER FILTER YES, TT Indicate whether you operate your
FILTER NO IMPRESSA with or without a CLEARYL
filter cartridge.
HARDNESS 1°dH – 30°dH TT Adjust the water hardness.
(is only displayed
when the filter is
not activated)
ECONOMY Save NO, TT Select an energy-saving mode.
MODE Save LEVEL 1,
SAVE LEVEL 2
TIME --:--, WEEKDAY TT Set the time and weekday.
22
Program item Subitem Explanation

UNIT ON/OFF TT Set the switch-on and switch-off time
individually for each weekday.
OFF AFTER OFF AFTER -- H, TT Set the number of hours after which the
0.5 H – 15 H IMPRESSA should switch off automatically.
RINSES INIT RINSE, TT Set whether the switch-on rinse should be
CAPP RINSE started manually or automatically.
TT Set whether the prompt for cappuccino
rinsing should be started immediately or
10 minutes afterpreparation of a milk
specialty.
INFORMATION TT Keep track of all prepared coffee and milk
specialties and view the maintenance status.
SETTINGS ML/OZ, TT Select the unit of the amount of water and
24HRS/AM PM the time format.
LANGUAGE TT Select the desired language.
EXIT TT Exit programming mode.
Settings in programming mode always follow the same model.
Example: To change the strength of one espresso from

ööö (normal) to öööö (strong).
appears.
g T Turn the Rotary Switch until PRODUCTS is displayed.
SELECT PRODUCT
EE Next select the product button for which you would like to
make settings. No product is prepared during this procedure.
i T Press the 1 Espresso button.

WATER 45 ML
g T Turn the Rotary Switch until AROMA ööö is displayed.
NORMAL ööö
23
g T Turn the Rotary Switch until STRONG öööö is displayed.

AROMA öööö
k T Press the Rotary Switch to exit the program item.
SELECT PRODUCT
PRODUCTS
COFFEE READY
Viewing information Under the program item INFORMATION you can query the fol-
and maintenance lowing information:
status ZZ Number of the prepared coffee and milk specialties
ZZ Maintenance status and number of maintenance programs
performed (cleaning, descaling, filter change)
ZZ Number of performed cappuccino cleaning operations

k T Press the Rotary Switch until MAINTENANCE appears.
g T Turn the Rotary Switch until INFORMATION is displayed.
TOTAL, the sum of all prepared coffee and milk specialties
is displayed.
g T Turn the Rotary Switch for further information.
EE The respective maintenance status can also be displayed in

addition to the number of performed maintenance programs.
The bar shows the current maintenance status. When the bar
is filled completely, your IMPRESSA will request the respective
maintenance program.

INFORMATION
COFFEE READY
24
4 Preparation at the touch of a button

a serious burn.
In this chapter you will find out how to prepare coffee and milk spe-
cialties and hot water without making further settings.
Chapter 3, ‘Familiarizing yourself with the control options’, will teach

you how to adjust the settings to your personal preferences. Alter-
natively, you can use Chapter 5, ‘Permanent settings in program-
ming mode’.
EE You can stop the machine at any time while a coffee or milk
product or hot water is being prepared. To do this, press any
button.
EE During preparation, you can change the pre-set amount of
water by turning the Rotary Switch.
water’).
Espresso The classic coffee drink from Italy. There is a definite crema on the
surface of the espresso.
Example: This is how to prepare one espresso.
TT Place an espresso cup under the coffee spout.
i T Press the 1 Espresso button.
1 ESPRESSO and the pre-set coffee strength are dis-
played.
C
25
EE To prepare two espressi place two cups under the coffee

spout and press the 2 Espressi button 4.
Coffee Example: This is how to prepare one coffee.

TT Place a coffee cup under the coffee spout.
1 COFFEE and the pre-set coffee strength are displayed.
C
EE To prepare 2 coffees, place two cups under the coffee spout

and press the 2 Coffees button d.
Coffee à la Carte The coffee strength of Coffee à la Carte can be changed before
preparation.
Example: Proceed as follows to prepare a strong (öööö) cup of

Coffee à la Carte.
e T Press the Coffee à la Carte button.
A LA CARTE ö
g T Turn the Rotary Switch until A LA CARTE öööö is
displayed.
k T Press the Rotary Switch while A LA CARTE öööö is
displayed.
A LA CARTE öööö, the pre-set amount of water flows
into the cup. Preparation stops automatically. ENJOY
appears on the display. COFFEE READY is then dis-
played.
26
Cappuccino Your IMPRESSA prepares a cappuccino at the touch of a button. It is

not necessary to move the cup.

TT Take the protective cover off the Professional Cappuccino
Frother.
TT Attach the milk pipe to the frother. For a milk carton/bottle
use the long pipe, for a milk container the short pipe.
TT Insert the other end into a milk carton/bottle or connect it to
the milk container.
TT Place a cup under the frother.

TT Turn the selection lever of the frother to the milk foam
position p.
p T Press the Cappuccino button.
CAPPUCCINO and the coffee strength are displayed.
The milk foam is then prepared. The operation stops auto-
matically when the pre-set amount of milk is reached.
Coffee preparation then begins. The pre-set amount of
water flows into the cup.
Preparation stops automatically. ENJOY appears on the
display. COFFEE READY is then displayed.
To ensure that the frother works perfectly, you should rinse and
clean it regularly. The description for this can be found in Chapter 6
‘Maintenance – Cappuccino frother’.
Latte macchiato Your IMPRESSA prepares a latte macchiato at the touch of the
button. It is not necessary to move the glass.

TT Take the protective cover off the Professional Cappuccino
Frother.
the milk container.
27
TT Place a glass under the frother.

position p.
q T Press the Latte Macchiato button.
LATTE MAC. and the coffee strength are displayed.
The milk foam is then prepared. The operation stops auto-
matically when pre-set amount of milk is reached.
EE A brief pause follows during which the hot milk separates from
the milk foam. This enables the formation of the typical layers
of a latte macchiato. The duration of this pause can be defined
in programming mode.
Coffee preparation then begins. The pre-set amount of

water flows into the glass. Preparation stops automatically.
ENJOY appears on the display. COFFEE READY is then
displayed.
Pre-ground coffee You can choose a second coffee blend, for example decaffeinated
coffee, with the filler funnel for pre-ground coffee.
EE Never add more than two level measuring spoons of pre-

ground coffee.
EE Use pre-ground coffee which is not ground too finely. Very
fine coffee can block up the system so that the coffee only
comes out in drips.
EE If you did not fill the machine with a sufficient amount of pre-
ground coffee, NOT ENOUGH PRE-GROUND is displayed
and the IMPRESSA stops operation.
All coffee specialties with pre-ground coffee are prepared following

this model.
Example: This is how to prepare a cup of coffee using pre-ground

coffee.
28
TT Open the cover of the filler funnel for pre-ground coffee.

v T Press the Pre-ground coffee button.
FILL PRE-GROUND / COFFEE READY
TT Place one level measuring spoon of pre-ground coffee into
the filler funnel.
TT Close the cover of the filler funnel for pre-ground coffee.
1 COFFEE, the pre-set amount of water flows into the
cup. Preparation stops automatically. ENJOY appears on
the display. COFFEE READY is then displayed.
Hot milk and milk There are two options for preparing hot milk or milk foam:
foam ZZ Milk portion z
UU The preset quantity of milk is then prepared.
ZZ Milk n
UU Milk is prepared until preparation is interrupted by pressing
any button.

TT Take the protective cover off the frother.
the milk container.
TT Place a cup under the frother.

position p.
EE If you want to heat the milk, set the selection lever of the
frother to the milk position t.
ö T With the selector switch select the milk portion symbol z.

ä T Press the selector switch.
MILK, the milk foam is being prepared. Preparation stops
automatically when the pre-set amount of milk is reached.
COFFEE READY is shown on the display.
29
Hot water Hot water can be prepared in two ways:

ZZ Hot water portion a
UU The pre-set amount of water flows into the cup.
ZZ Hot water m
UU Water flows out of the hot water spout until preparation is
interrupted by pressing any button.
The following temperatures can be selected for preparing hot

water:
ZZ Low
ZZ Normal
ZZ X high
J CAUTION There is a danger of scalding from hot water splashes.

T Avoid direct contact with the skin.
Example: This is how to prepare a portion of hot water.

TT Place a cup under the hot water spout.
ö T Use the selector switch to select the hot water portion
symbol a.
ä T Press the selector switch.
TEMPERATURE and the pre-set temperature are dis-
played.
EE By pressing the selector switch several times (within approx.

2 seconds) you can set the temperature to your individual
preference. This setting is not saved.
HOT WATER, the pre-set amount of water flows into the

cup. Preparation stops automatically. COFFEE READY
30
5 Permanent settings in programming mode

Products With the PRODUCTS program item you can enter individual set-
tings for all coffee and milk specialties as well as hot water.
a serious burn.
The following permanent settings can be made:
Product Amount Coffee strength Temp.

1 Espresso, 0.5 OZ – 8.0 OZ (25 ml – 240 ml) ö (xmild), NORMAL,
1 Coffee öö (mild), HIGH
ööö (normal),
öööö (strong),
ööööö (xstrong)
2 Espressi, 0.5 OZ – 8.0 OZ (25 ml – 240 ml) – NORMAL,
2 Coffees (per cup) HIGH
Coffee à la 0.5 OZ – 8.0 OZ (25 ml – 240 ml) – NORMAL,
Carte HIGH
Cappuccino, Amount of milk: 3 SEC – 120 SEC ö (xmild), NORMAL,
Latte Pause: 0 SEC – 60 SEC öö (mild), HIGH
macchiato Amount of water: 0.5 OZ – 8.0 OZ ööö (normal),
(25 ml – 240 ml) öööö (strong),
ööööö (xstrong)
Milk portion 3 SEC – 120 SEC – –
Milk – – –
Hot water 0.5 OZ – 15.0 OZ – LOW, NORMAL,
portion (25 ml – 450 ml) X HIGH
Hot water – – LOW, NORMAL,
X HIGH
31
EE The products which are selected with the selector switch can
be individually set to inactive. This means that the respective
symbols are not visible and preparation is not possible.
Permanent settings in programming mode always follow the same

model.
Example: Proceed as follows to change the amount of milk of latte

macchiato from 16 SEC to 20 SEC, the pause from 30 SEC
to 40 SEC and the amount of water from 1.5 OZ (45 ml) to
1.0 OZ (40 ml).
appears.
g T Turn the Rotary Switch until PRODUCTS is displayed.
SELECT PRODUCT
EE Next select the product button for which you would like to
make settings. No product is prepared during this procedure.
q T Press the Latte Macchiato button.

COFFEE 1.5 OZ (45 ml)
COFFEE 1.5 OZ (45 ml)
g T Turn the Rotary Switch until COFFEE 1.0 OZ (40 ml) is
displayed.
COFFEE 40 ML
g T Turn the Rotary Switch until MILK 16 SEC is displayed.
MILK 16 SEC
g T Turn the Rotary Switch until MILK 20 SEC is displayed.
MILK 20 SEC
g T Turn the Rotary Switch until PAUSE 30 SEC is dis-
played.
32

PAUSE 30 SEC
g T Turn the Rotary Switch until PAUSE 40 SEC is dis-
played.
PAUSE 40 SEC
SELECT PRODUCT
PRODUCTS
COFFEE READY
Resetting the products to You can reset the values of all products as well as cappuccino and
works settings latte macchiato individually to the works setting.
Example: Proceed as follows to reset the values of 1 Espresso to the

works setting.
Precondition: The IMPRESSA is switched off (standby).
TT Press the Rotary Switch and the 1 Espresso button for two
seconds at the same time until 1 ESPRESSO OK
appears.
The values of 1 Espresso are then reset to the works setting.
The IMPRESSA is switched off (standby).
Energy-saving mode You can also set various energy-saving modes on your IMPRESSA:
(Energy Save Mode, ZZ SAVE NO
E.S.M.©) UU Your IMPRESSA is continuously ready for use.
UU All coffee and milk products, as well as hot water, can be
prepared without having to wait.
ZZ SAVE LEVEL 1
UU Your IMPRESSA is only continuously ready for use for coffee
products and hot water.
UU The machine has to heat up before milk preparation.
33
ZZ SAVE LEVEL 2
UU Approx. 5 minutes after the last preparation the IMPRESSA
switches to the energy-saving temperature and is not ready
for use.
UU Before coffee, hot water or milk can be prepared, the m
achine
has to heat up.
Example: Proceed as follows to change the energy-saving mode

from SAVE NO to SAVE LEVEL 1.
appears.
g T Turn the Rotary Switch until ECONOMY MODE - is dis-
played.
SAVE NO
g T Turn the Rotary Switch until SAVE LEVEL 1 is displayed.
ECONOMY MODE 1
COFFEE READY
Time and weekday You already set the time and weekday when you used the machine
for the first time.
Example: To change the time from 08:45 to 09:50, proceed

as follows.
appears.
g T Turn the Rotary Switch until TIME 08:45 is displayed.
TIME 08:45
34

WEEKDAY MONDAY (Example)
k T Press the Rotary Switch to confirm the weekday setting.
TIME 09:50
COFFEE READY
Programmable The programmable switch-on and switch-off time can only be set
switch-on and when the time has been set.
switch-off time
The following settings can be made in the UNIT ON/OFF menu
item:
ZZ UNIT ON
UU Set the required switch-on time.
ZZ MACH. OFF
UU Set the required switch-off time.
ZZ ON/OFF
UU Set the weekdays on which IMPRESSA should switch on and
off automatically.
EE The programmable switch-on only works when the machine

is switched on at the power switch (standby).
Example: Proceed as follows to set the programmable switch-on

time to 07:30 and stipulate that your IMPRESSA does not switch
on automatically on Sundays.
appears.
g T Turn the Rotary Switch until UNIT ON/OFF is displayed.
UNIT ON --:--
UNIT ON --:--
35
g T Turn the Rotary Switch until UNIT ON 07:00 is dis-

played.
g T Turn the Rotary Switch until UNIT ON 07:30 is dis-
played.
UNIT ON 07:30
g T Turn the Rotary Switch until ON/OFF / MON YES is dis-
played.
ON/OFF / MON YES
g T Turn the Rotary Switch until ON/OFF / SUN YES is dis-
played.
ON/OFF / SUN YES
g T Turn the Rotary Switch until ON/OFF / SUN NO is dis-
played.
ON/OFF / SUN NO
ON/OFF / MON YES
UNIT ON/OFF
COFFEE READY
Automatic switch-off By instructing your IMPRESSA to automatically switch itself off, you
can cut down your energy consumption. If this function is activated,
your IMPRESSA switches off automatically after the last action on
the machine.
EE The programmable switch-off time can be adjusted between

0.5 and 15 hours or deactivated.
36
Example: Proceed as follows to change the automatic switch-off

time from 1 H to 2 H.
appears.
g T Turn the Rotary Switch until OFF AFTER 1 H is dis-
played.
OFF AFTER 1 H
g T Turn the Rotary Switch until OFF AFTER 2 H is dis-
played.
OFF AFTER 2 H
COFFEE READY
Rinses You can set whether the switch-on rinse should be started manu-
ally or automatically.
You can set whether cappuccino rinsing should be prompted imme-

diately or 10 minutes after a milk product has been prepared.
Example: Proceed as follows to program that Cappuccino rinsing

should be prompted immediately after a milk product has been
prepared.
appears.
g T Turn the Rotary Switch until RINSES is displayed.
INIT RINSE MANUAL
g T Turn the Rotary Switch until CAPP RINSE AFTER 10’
is displayed.
CAPP RINSE AFTER 10’
37
g T Turn the Rotary Switch until CAPP RINSE NOW is

displayed.
CAPP RINSE NOW
RINSES
COFFEE READY
Unit amount of You can change the unit of the amount of water from ‘ml’ to ‘oz’ and
water / time format the time format to ‘24 HRS’ or ‘AM/PM’ .
Example: To change the unit for the amount of water from ML to

OZ, proceed as follows.
appears.
g T Turn the Rotary Switch until SETTINGS 24HRS / ML
is displayed.
SETTINGS 24HRS
g T Turn the Rotary Switch until SETTINGS ML is displayed.
SETTINGS ML
g T Turn the Rotary Switch until SETTINGS OZ is displayed.
SETTINGS OZ
SETTINGS 24HRS / OZ
COFFEE READY
38
Language You set the language when you used the machine for the first time.
Example: To change the language from ENGLISH to DEUTSCH

(example), proceed as follows.
appears.
g T Turn the Rotary Switch until LANGUAGE ENGLISH is
displayed.
LANGUAGE ENGLISH
g T Turn the Rotary Switch until SPRACHE DEUTSCH
(example) is displayed.
GESPEICHERT w (example) appears briefly on the dis-
play.
SPRACHE DEUTSCH (example)
BITTE WÄHLEN (example)
39
6 Maintenance
6 Maintenance
J WARNING Use of maintenance products that are harmful to health and dis-
charge of liquids during maintenance program. Harmful if swal-
lowed. Irritating to eyes and skin.
T Keep children away from the machine while it is performing a
maintenance program.
T Avoid contact with skin and eyes.
T Avoid generation of dust. Do not inhale dust.
T When using do not eat or drink.
T Keep maintenance products away from food, drink and ani-
mal food.
T Keep container tightly closed and dry. Keep in a cool place.
Your IMPRESSA has the following integrated maintenance pro-

grams:
ZZ Rinse machine
ZZ Change filter
ZZ Clean machine
ZZ Decalcify machine
ZZ Rinse cappuccino frother
ZZ Clean cappuccino frother
EE Clean or descale the machine or change the filter whenever

the appropriate prompt is displayed.
Maintenance tips To ensure that you get many years of reliable service out of your
IMPRESSA and to guarantee the optimum coffee quality, the

machine requires daily maintenance.
You should proceed as follows:

ZZ Empty the coffee grounds container and the drip tray. Rinse
them with warm water.
ZZ Rinse the water tank with clean water.
ZZ Dismantle and rinse the frother (see Chapter 6
‘Maintenance – Rinsing the cappuccino frother’).
ZZ Wipe the surface of the machine with a damp cloth.
40
6 Maintenance
Rinsing the machine When the IMPRESSA is switched on, a prompt to perform a rinse
operation appears after heating, or this is automatically started.
It can be set in programming mode whether the switch-on rinse

needs to be activated manually or whether the machine automati-
cally activates the switch-on rinse (see Chapter 5 ‘Permanent set-
tings in programming mode – Rinses’).
When the IMPRESSA is switched off, a rinse operation is automati-

cally initiated.
You can initiate the rinse operation manually at any time.

appears.
CLEAN CAPPUCCINO
f T Turn the Rotary Switch until RINSE MACHINE is dis-
played.
k T Press the Rotary Switch to initiate the rinse operation.
MACHINE RINSING
Rinsing stops automatically and your IMPRESSA is then once
more ready for use.
Changing the filter EE After 2000 oz (60 liters) of water have flowed through, the fil-
ter will cease to work. Your IMPRESSA will automatically
prompt you to replace the filter.
EE After two months, the filter will cease to work. Monitor the
elapsed time by adjusting the date plate on the cartridge
holder.
EE If the CLEARYL filter cartridge is not activated, you will not be
prompted to change the filter.
Change following a prompt To change the CLEARYL filter cartridge when prompted to do so by
your IMPRESSA, proceed as follows:
Precondition: COFFEE READY / CHANGE FILTER is dis-

played, and the maintenance button c lights up.
41
6 Maintenance

DURATION 2 MIN. / START YES
EE If you want to change the filter at a later point in time, turn the
Rotary Switch until START NO is displayed. Exit the mainte-
nance program by pressing the Rotary Switch. The prompt
‘Change filter’ remains on the display.

CHANGE FILTER / PRESS RINSE
TT Lift the cartridge holder.
TT Take out the old CLEARYL filter cartridge and the extension.
TT Fit the extension on top of a new filter cartridge.
TT Insert the filter cartridge into the water tank, exerting slight
pressure.
TT Close the cartridge holder. It will click into place audibly.
TT Place a receptacle (at least 17 oz or 500 ml) under the frother.
EE If you are using the Professional Cappuccino Frother, set the

selection lever of the frother to the steam position n.

FILTER RINSING, water flows out of the frother.
EE You can interrupt filter rinsing at any time. To do this, press
any button.
EE The water may be slightly discolored. This is not harmful to
health and does not affect the taste.
Filter rinsing stops automatically after approx. 17 oz (500 ml).

The IMPRESSA heats up and is once again ready to use.
Manual filter change You can initiate the ‘Changing the filter’ operation manually.
Precondition: The filter is activated and COFFEE READY is

shown on the display.
42
6 Maintenance

appears.
CLEAN CAPPUCCINO
g T Turn the Rotary Switch until CHANGE FILTER is dis-
played.
k T Press the Rotary Switch.
TT Continue with the second prompt to take action (indicated

by a T), as is described under ‘Replacement following a
prompt’.
Cleaning the machine After 220 coffee preparations or 80 switch-on rinses, the IMPRESSA
will prompt you to clean it.
J WARNING Non-recommended (e.g. liquid) cleaning agents may contain sub-

stances that could damage the machine or leave residues.
T Use only original JURA cleaning tablets. These are specially
formulated for your machine.
J WARNING Harmful and irritating cleaning agent. Harmful if swallowed. Irritat-

ing to eyes and skin.
T After contact with skin, wash immediately with plenty of
water. In case of skin irritation, seek medical advice.
T After eye contact, immediately flush eyes with plenty of water
and seek medical advice.
T If swallowed, rinse mouth immediately and drink large quan-
tities of water. Do not induce vomiting. Seek medical advice
immediately and show label.
EE The cleaning program only lasts about 20 minutes.

EE Do not interrupt the cleaning program. The quality of cleaning
will be impaired if you do so.
EE JURA cleaning tablets are available from specialized dealers.
43
6 Maintenance
Cleaning following Precondition: COFFEE READY / CLEAN MACHINE is dis-

a prompt played, and the maintenance button c lights up.
EE If you want to clean the machine at a later point in time, turn
the Rotary Switch until START NO is displayed. Exit the
maintenance program by pressing the Rotary Switch. The
prompt ‘Clean machine’ remains on the display.

EMPTY TRAY
TT Empty the drip tray and coffee grounds container and put
them back into the machine.
TT Place a receptacle under the coffee spout and the frother.
CLEANS, the cleaning operation starts.
The process is interrupted. ADD TABLET / PRESS
RINSE, the maintenance button c lights up.
TT Open the cover of the filler funnel for pre-ground coffee.
TT Insert a JURA cleaning tablet into the filler funnel.

TT Close the cover of the filler funnel.
CLEANS, water flows out of the coffee spout and the froth-
er several times.
EE You can follow the current status of cleaning on the progress

bar.
The process is interrupted, EMPTY TRAY.

The cleaning operation is now complete. The IMPRESSA is
ready for use again.
Manual cleaning You can initiate the ‘Cleaning the machine’ operation manually.

44
6 Maintenance

appears.
CLEAN CAPPUCCINO
g T Turn the rotary switch until CLEAN MACHINE is dis-
played.
by a T), as is described under ‘Cleaning following a prompt’.
Descaling the machine The IMPRESSA builds up deposits of limescale over time and auto-
matically prompts you to descale it when necessary. The degree of
calcification depends on the degree of hardness of your water.
J WARNING Non-recommended descaling agents (e.g. vinegar) may contain

substances that could damage the machine or leave residues.
T Use only original JURA descaling tablets. These are specially
formulated for your machine.
J WARNING Harmful and irritating descaling agent. Harmful if swallowed. Irritat-

T After eye contact, immediately flush eyes with plenty of water.
Remove contact lenses. Seek medical advice.
NOTICE If the descaling operation is interrupted, there may be damage to

the machine.
T Allow the descaling program to run to the end.
EE The descaling program lasts approx. 45 minutes.

EE JURA descaling tablets are available from specialized dealers.
45
6 Maintenance
EE If you use a CLEARYL filter cartridge and this is activated, you

will not be prompted to change the filter.
EE If the descaling agent comes into contact with sensitive sur-
faces (e.g. marble), damage cannot be ruled out. Clean up any
splashes immediately.
Descaling following Precondition: COFFEE READY / DECALCIFY MACHINE is

a prompt displayed and the maintenance button c lights up.
EE If you want to descale the machine at a later point in time, turn
the Rotary Switch until START NO is displayed. Exit the
maintenance program by pressing the Rotary Switch. The
prompt ‘Decalcify machine’ remains on the display.

EMPTY TRAY
SOLVENT IN TANK
TT Completely dissolve the contents of one blister (3 JURA des-
caling tablets) in a container that holds 20 oz (600 ml) of
water. This may take several minutes.
TT Pour the solution into the empty water tank and insert it in
the machine.
SOLVENT IN TANK / PRESS RINSE, the mainte-
nance button c lights up.
TT Remove the frother from the Connector System©.
under the Connector System©.
DECALCS, water flows out of the Connector System© and
the hot water spout. The maintenance button c flashes
during the descaling operation.
EE You can follow the current status of descaling on the progress

bar.
The process is interrupted, EMPTY TRAY.

46
6 Maintenance
TT Empty the receptacles below the hot water spout and the
Connector System©.
RINSE WATER TANK / FILL WATER TANK
TT Remove the water tank and rinse it thoroughly.
TT Refit the frother.
TT Place a receptacle under the coffee and hot water spout and
another under the frother.
DECALCS, water flows out of the frother and the hot water
spout.
The process is interrupted, HEATING UP.
MACHINE RINSING, water flows out of the coffee
spout. The operation stops automatically, EMPTY TRAY.
The descaling operation is now complete. Your IMPRESSA
heats up and is once again ready to use.
EE If the descaling operation stops unexpectedly, rinse the water

tank thoroughly.
Manual descaling You can initiate the ‘Descaling the machine’ operation manually.
Precondition: COFFEE READY is shown on the display and the

filter is not activated.
appears.
CLEAN CAPPUCCINO
g T Turn the Rotary Switch until DECALCIFY MACHINE
is displayed.
by a T), as is described under ‘Descaling following a prompt’.
47
6 Maintenance
Rinsing the Each time milk has been prepared the IMPRESSA displays a prompt
cappuccino frother for Cappuccino rinsing.
It can be set in programming mode whether the rinsing prompt is

displayed immediately or 10 minutes after preparation (refer to
Chapter 5 ‘Permanent settings in programming mode – Rinses’).
Rinsing following a prompt Precondition: COFFEE READY / RINSE CAPPUCCINO is

displayed and the maintenance button c lights up.
TT Place a receptacle under the frother.
EE If you are using the Professional Cappuccino Frother, turn

the selection lever to the steam position n.

CAPPU. RINSING, the frother is rinsed.
The procedure stops automatically. COFFEE READY
Starting rinsing manually You can initiate the ‘Rinsing the cappuccino frother’ operation
manually.

TT Place a receptacle under the frother.

the selection lever to the steam position n.

appears.
CLEAN CAPPUCCINO
g T Turn the Rotary Switch until RINSE CAPPUCCINO is
displayed.
k T Press the Rotary Switch to start the rinse operation.
CAPPU. RINSING, the frother is rinsed.
The procedure stops automatically. COFFEE READY
48
6 Maintenance
Cleaning the To ensure that the respective frother works perfectly, you should
cappuccino frother clean it daily when you have been preparing milk.
J WARNING Non-recommended cleaning agents will not optimally remove milk

residues. This may cause the cappuccino frother to become blocked
and fly off the machine. Discharge of hot steam.
T Use only original JURA Cappuccino Cleaner.
J WARNING Harmful and irritating cleaning agent. Harmful if swallowed. Irritat-

T After eye contact, immediately flush eyes with plenty of water
and seek medical advice.
EE The IMPRESSA will not prompt you to clean the frother.

EE The JURA Cappuccino Cleaner is available from specialized
dealers.
Cleaning the cappuccino Precondition: COFFEE READY is displayed.

frother – manually TT Open the cover of the Rotary Switch.
appears.
CLEAN CAPPUCCINO
CLEANER FOR CAPPU., the maintenance button c
lights up.
TT Pour 8.5 oz (250 ml) of fresh water into a container and add
one capful (max. 0.5 oz (15 ml)) of Cappuccino Cleaner.
TT Immerse the milk pipe in the receptacle with the cleaning
solution.

the selection lever to the milk foam p or milk t position.
49
6 Maintenance
TT Place another receptacle under the frother.

CAPPUCCINO / CLEANS, the frother and pipe are
cleaned.
WATER FOR CAPPUCCINO, the maintenance button c
lights up.
TT Rinse the receptacle thoroughly, fill it with approx. 8.5 oz
(250 ml) of fresh water and immerse the milk pipe in the wa-
ter.
TT Empty the other receptacle and place it under the frother
once more.
CAPPUCCINO / CLEANS, the frother and pipe are rinsed
with fresh water.
is once more ready to use.
Cleaning the cappuccino If milk has been prepared, but the cappuccino frother has not been
frother after a prompt cleaned, the CLEAN CAPPUCCINO prompt is displayed when
the machine is switched off. The maintenance program can be
started by pressing the maintenance button c.
Precondition: CLEANER FOR CAPPU. is displayed and the

maintenance button c lights up.
TT Continue with the fifth prompt to take action (indicated
by a T), as is described under ‘Cleaning the cappuccino
frother – manually’.
Disassembling and
rinsing the Professional TT Carefully remove the frother from the Connector System©
Cappuccino Frother by twisting slightly.
TT Dismantle the frother completely.
TT Rinse all the frother parts thoroughly under running water.
TT Reassemble the frother.
EE Ensure that the individual parts are correctly and firmly

attached to one another to ensure optimum function of the
frother.
TT Firmly attach the frother to the Connector System©.
50
6 Maintenance
Cleaning the Coffee beans may be covered with a slight oil film which remains on
bean container the walls of the bean container. These residues may negatively affect
the coffee results. For this reason clean the bean container from
time to time.
J WARNING Danger of injury to the fingers when the grinder is running.

TT Switch the machine off with the on/off button Q before per-
forming any work on the grinder.
TT Switch the machine off at the power switch 3.
TT Open the cover of the bean container and remove the aroma
preservation cover.
TT Remove the beans with a vacuum cleaner.
TT Loosen the screw in the bean container and lift up the finger
protection.
TT Remove the remaining beans with a vacuum cleaner.
TT Clean the bean container with a soft, dry cloth.
TT Put the finger protection down again and screw it back
tightly in place.
TT Fill the bean container with coffee beans, then close the
aroma preservation cover and the bean container cover.
Descaling the water Limescale deposits may form in the water tank. To ensure correct
tank function of your IMPRESSA, you should descale the water tank from
time to time.
TT Remove the water tank.

TT If you use a CLEARYL filter cartridge, remove this.
TT Descale the tank with a mild, commercially available descal-
ing agent in accordance with the instructions of the manu-
facturer.
TT Rinse the water tank with clean water afterwards.
TT If you use a CLEARYL filter cartridge, insert this again.
51
7 Display messages
7 Display messages
Message Cause/Result Action

FILL WATER TANK The water tank is empty. TT Fill the water tank (see
You cannot prepare any coffee Chapter 2, ‘Preparing and using
products, hot water or milk for the first time – Filling the
products. water tank’).
EMPTY GROUNDS The coffee grounds container TT Empty the coffee grounds
is full. You cannot prepare any container and the drip tray.
coffee products, but you can
prepare hot water or milk.
EMPTY TRAY The drip tray is full. You cannot TT Empty the drip tray.
prepare any coffee products,
hot water or milk products.
TRAY MISSING The drip tray is not inserted TT Insert the drip tray.
correctly or is not inserted at TT Clean the metal contacts on
all. You cannot prepare any the back of the drip tray.
coffee products, hot water or
milk products.
FILL BEANS The bean container is empty. TT Fill the bean container (see
You cannot prepare any coffee Chapter 2, ‘Preparing and using
products, but you can prepare for the first time – Filling the
hot water or milk. bean container’).
PRESS RINSE The IMPRESSA is prompting TT Press the maintenance button
you to start a rinse operation to start rinsing or to continue the
or continue a started mainte- maintenance program.
nance program.
COFFEE READY / The IMPRESSA is prompting TT Press the maintenance button
RINSE CAPPUCCINO you to start cappuccino to start cappuccino rinsing.
rinsing.
COFFEE READY / After 220 preparations or TT Clean the machine (see
CLEAN MACHINE 80 switch-on rinses, the Chapter 6, ‘Maintenance –
IMPRESSA will prompt you to Cleaning the machine’).
clean it.
52
7 Display messages
Message Cause/Result Action

COFFEE READY / After 250 preparations the TT Clean the machine (see
CLEAN NOW IMPRESSA will prompt you Chapter 6, ‘Maintenance –
to clean it. Cleaning the machine’).
COFFEE READY / The IMPRESSA is prompting TT Descale the machine (see
DECALCIFY MACHINE you to descale it. Chapter 6, ‘Maintenance –
Descaling the machine’).
COFFEE READY / The IMPRESSA is prompting TT Descale the machine (see
DECALCIFY NOW you to descale it. Chapter 6, ‘Maintenance –
Descaling the machine’).
COFFEE READY / After 2000 oz (60 liters) of TT Replace the CLEARYL filter
CHANGE FILTER water have flowed through, or cartridge (see Chapter 6
after two months, the filter will ‘Maintenance – Changing the
cease to work. filter’).
COFFEE READY / After 2200 oz (65 liters) of TT Replace the CLEARYL filter
CHANGE NOW water have flowed through, cartridge (see Chapter 6
the filter will cease to work. ‘Maintenance – Changing the
filter’).
NOT ENOUGH There is too little pre-ground TT The next time you make coffee
PRE-GROUND coffee in the filler funnel. The use more pre-ground coffee
IMPRESSA stops the operation. (refer to Chapter 4, ‘Preparation
at the touch of a button –
Pre-ground coffee’).
53
8 Troubleshooting
8 Troubleshooting
Problem Cause/Result Action

Grinder is making a very There are foreign objects TT Contact Customer Support in your
loud noise. in the grinder. country (see ‘JURA contact details /
Legal information’).
The frother does not The cappuccino frother TT Rinse and clean the cappuccino
produce enough milk foam is dirty or incorrectly frother (see Chapter 6, ‘Maintenance –
or milk sprays from the attached. Cappuccino frother‘).
cappuccino frother. TT Assemble the cappuccino frother
correctly and firmly attach the frother
to the Connector System© (refer to
Chapter 6 ‘Maintenance – Disassem-
bling and rinsing the frother’).
Coffee only comes out Coffee or pre-ground TT Put the grinder on a coarser setting
in drips when it is being coffee has been ground or use coarser pre-ground coffee (refer
prepared. too finely and is blocking to Chapter 2, ‘Preparing and using for
the system. the first time – Adjusting grinder’).
Water hardness cannot The CLEARYL filter TT Deactivate the CLEARYL filter
be adjusted. cartridge is activated. cartridge in programming mode.
COFFEE READY / The grinder is not yet TT Prepare a coffee specialty.
FILL BEANS completely filled with
is displayed although beans.
the bean container has
been filled.
COFFEE READY / The bean monitor is TT Clean the bean container
FILL BEANS is not dirty. (see Chapter 6, ‘Maintenance –
displayed although the Cleaning the bean container’).
bean container is empty.
EMPTY TRAY The metal contacts of the TT Clean and dry the metal contacts
is always displayed. drip tray are dirty or wet. on the back of the drip tray.
FILL WATER TANK The water tank float is TT Descale the water tank (see
is displayed although trapped. Chapter 6, ‘Maintenance – Descaling
the water tank is full. the water tank’).
54
8 Troubleshooting
Problem Cause/Result Action

ERROR 2 is displayed. If the machine was TT Warm up the machine at room
exposed to the cold for a temperature.
long period of time, it is
disabled from heating up
due to safety reasons.
Other ERROR messages – TT Turn the IMPRESSA off at the power
are displayed. switch. Contact Customer Support in
your country (see ‘JURA contact
details / Legal information’).
EE If you have not been able to solve the problem, contact Cus-
tomer Support in your country (see ‘JURA contact details /
Legal information’ ).
55
9 Transport and environmentally neutral disposal
9 Transport and environmentally neutral disposal

Transport / Emptying Keep the packaging for your IMPRESSA. It should be used to protect
the system the machine during transportation.
In order to protect the IMPRESSA from frost during transportation,

the system must be emptied.
Precondition: The IMPRESSA is switched off (standby).

TT Remove the water tank.
under the frother.
c T Press the maintenance button until SYSTEM
EMPTYING appears.
A small amount of water flows from the frother and the
hot water spout. The operation stops automatically. The
IMPRESSA will switch itself off.
3 T Turn your IMPRESSA off at the power switch.
EE The next time you use the machine the system must be
refilled (see Chapter 2, ‘Preparing and using for the first
time – First-time use’).
Disposal Please dispose of old machines in an environmentally neutral way.

H
56
10 Technical data
10 Technical data
Voltage 120 V ~, 60 Hz

Power 1250 W
Safety test
Energy SAVE NO 23 Wh
Energy SAVE LEVEL 1 16 Wh
Energy SAVE LEVEL 2 14 Wh
Energy consumption in standby 5.6 Wh
mode
Pump pressure Static max. 15 bar
Holding capacity of water tank 96 oz (2.8 l)
Holding capacity of bean 10 oz (280 g)
container
Holding capacity of coffee Approx. 20 servings
grounds container
Cord length Approx. 43.3 in. (Approx. 1.1 m)
Weight 29.3 lb (13.3 kg)
Dimensions (W x H x D) 16.2 x 18.5 x 15.4 in.
(41 x 47 x 39cm)
Directives The machine complies with the following directives:

ZZ Standard UL 1082
ZZ Canadian Standard CSA C22.2 No. 64
57
Index
Index
A Entering a default setting for the amount of
Addresses 60 water for a cup size 21
Aroma preservation cover 8 Errors
Automatic switch-off 36 Troubleshooting 54
B Espresso 25
Bean container F
Aroma preservation cover 8 Filler funnel for pre-ground coffee 8
Cleaning 51 Filling
Cover 8 Bean container 12
Filling 12 Water tank 12
C Filter
Cappuccino 27 Changing 41
Cappuccino frother Using and activating 14
Cleaning 49 Fineness of grind
Rinsing 48 Adjusting grinder 17
Cleaning Fineness of grind switch 8
Bean container 51 Fineness of grind switch 8
Cappuccino frother 49 First-time use 13
Machine 43 H
CLEARYL filter cartridge Hardness of water 16
Changing 41 Hotline 60
Using and activating 14 Hot milk 29
Coffee 26 Hot water 30
Coffee à la carte 26 Hot water portion 30
Coffee grounds container 8 Hot water spout 8
Coffee spout, height-adjustable 8 I
Contact details 60 Important safeguards
Control options 19 Safety 4
Cover Internet 11
Bean container 8
Filler funnel for pre-ground coffee 8
J
JURA
Customer support 60
Contact details 60
D L
Default settings in programming mode 31
Language 39
Descaling
Latte macchiato 27
Machine 45
Water tank 51 M
Display messages 52 Machine
Cleaning 43
Display, Messages 52
Descaling 45
Drip tray 8
Rinsing 41
E Setting up 12
Emptying the system 56 Switching off (stand-by) 18
Energy-saving mode 33 Switching on 17
58
Index
Maintenance 40 S
Maintenance tips 40 Safety
Milk Important safeguards 4
Hot 29 Selector switch 9
Milk portion 29 Settings
Milk foam 29 Default settings in programming mode 31
O Entering a default setting for the amount of
One-off settings before and during prepara- water for a cup size 21
tion 20 One-off settings before and during prepara-
P tion 20
Power switch 8 Setting up 12
Pre-ground coffee 28 Standby
Filler funnel 8 Switching off 18
Pre-ground coffee 28 Switching off (stand-by) 18
Preparation Switching on 17
At the touch of a button 25 Symbol description 3
Cappuccino 27 T
Coffee 26 Technical data 57
Coffee à la carte 26 Telephone 60
Espresso 25 Time and weekday 34
Hot water 30
Troubleshooting 54
Latte macchiato 27
Milk 29 U
Pre-ground coffee 28 Use, First time 13
Problems V
Troubleshooting 54 Viewing information and maintenance status
Professional Cappuccino Frother 8 24
Disassembling and rinsing 50 Viewing maintenance status 24
Programmable switch-on and switch-off time W
35 Water hardness 16
Programming mode 31 Determining and adjusting 16
Automatic switch-off 36 Water tank 8
Energy-saving mode 33 Descaling 51
Language 39 Filling 12
Products 31 Works settings 33
Rinses 37
Switch-on and switch-off time 35
Time and weekday 34
Unit amount of water/Time format 38
R
Rinses 37
Rinsing
Cappuccino frother 48
Machine 41
Rotary Switch 9
59

The IMPRESSA S9 One Touch Classic Manual: For Your Safety: Read and Understand Manual Before Use

Uploaded by

Copyright:

Available Formats

The IMPRESSA S9 One Touch Classic Manual: For Your Safety: Read and Understand Manual Before Use

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

The IMPRESSA S9 One Touch Classic Manual: For Your Safety: Read and Understand Manual Before Use

Uploaded by

Copyright:

Available Formats

Figure: Your machine may look

different to the one shown.

The IMPRESSA S9 One Touch Classic Manual

KE For your safety: read and understand manual before use.

Your IMPRESSA S9 One Touch Classic

Cleaning the machine.................................................................................................................................43

SAVE THESE INSTRUCTIONS.

People, including children, who

Do NOT use extension cords.

In the event of signs of damage, for example if there is a smell of

There is a risk of scalds or burns on the spouts and the cappuccino

NOTICE ZZ Never clean with scouring powders or hard implements.

1 Bean container cover 8 Fineness of grind switch

Front left Front right

1 IMPRESSA S9 One Touch Classic

ZZ One Touch Cappuccino/Latte macchiato: Your IMPRESSA S9

ZZ Energy-saving mode (Energy Save Mode, E.S.M.©): The

ZZ Control philosophy: You can ‘navigate’ reliably through all

ZZ Professional technology for the home: The active bean mon-

JURA on the Internet Visit us on the Internet.

@@ At www.jura.com you will find interesting and up-to-date

2 Preparing and using for the first time

Setting up When setting up your IMPRESSA, please note the following:

TT Remove the water tank and rinse it with cold water.

EE The water volume is given as standard in ‘oz’. You can change

Precondition: The water tank and bean container are full.

TT Open the cover of the Rotary Switch.

k T Press the Rotary Switch to confirm the setting.

EE After first-time use do not disconnect the IMPRESSA from the

EE Perform the ‘Insert filter’ operation without interruptions. This

Precondition: COFFEE READY is displayed.

k T Keep the Rotary Switch pressed until MAINTENANCE

TT Place a receptacle (at least 17 oz or 500 ml) under the frother.

EE If you are using the Professional Cappuccino Frother, set the

c T Press the maintenance button.

EE You can interrupt rinsing of the filter at any time by pressing

Filter rinsing stops automatically after approx. 17 oz (500 ml).

Example: To change the water hardness from 16°dH to 25°dH,

k T Press the Rotary Switch to confirm the setting.

The consistency of grind setting is correct if the coffee flows regu-

Example: To change the fineness of grind during coffee preparation,

This setting can be changed in programming mode so that the

Q T Press the on/off button to switch the IMPRESSA on.

TT Place a receptacle under the coffee spout and the frother.

EE When you prepare a milk product, but have not performed

The IMPRESSA is switched off (standby mode), and the

EE When your IMPRESSA is switched off, a hissing noise may be

3 Familiarizing yourself with the control options

Learn how to perform the following:

Example: This is how to prepare one coffee.

EE To prepare 2 coffees, place two cups under the coffee spout

Example: Proceed as follows to to prepare a strong cup of Coffee à

appears on the display. COFFEE READY is then dis-

Example: Proceed as follows to prepare a 110 ML cup of coffee.

Example: To make permanent settings for the amount of water for

TT Press any button as soon as enough espresso has flowed

EE You can alter these settings at any time by repeating the

Program item Subitem Explanation

Settings in programming mode always follow the same model.