An Introduction to

Thermal Spray
Issue 5 – October 2014
An Introduction to Thermal Spray – Issue 5 – October 20142
Contents

1 Introduction.......................................................................................4
1.1 Surface Properties..................................................................................... 4
1.2 Coating processes.................................................................................... 5
2 Thermal sprayed coatings.................................................................6
2.1 Definition................................................................................................... 6
2.2 Substrate materials................................................................................... 6
2.3 Coating material........................................................................................ 7
2.4 Thermal Spray coating processes............................................................. 8
2.5 Coating structure..................................................................................... 13
2.6 Coating characteristics............................................................................ 14
2.7 Post processing...................................................................................... 14
2.8 Coating characterization.......................................................................... 15
3 Applications....................................................................................16
3.1 Production applications........................................................................... 17
3.2 Salvage and restoration........................................................................... 20
4 Summary.........................................................................................21
5 Appendix.........................................................................................22
5.1 Reference tables..................................................................................... 22
5.2 Literature references................................................................................ 23

An Introduction to Thermal Spray – Issue 5 – October 20143

1 Introduction
In all sectors of industry today, the catch phrase “better, fast-
er, cheaper” is common and valid, as it seems that produc-
tion demands are ever-increasing. Highly demanding require-
ments and aggressive service conditions often lead to the
premature loss of component or system function.

Shown in Figure 1 a is a completely worn pelton turbine noz-

zle needle after some thousand hours of actual service. If this
service life is deemed unacceptable, either the entire compo-
nent must be made of a more wear resistant material, or the
area where the wear occurs must be protected. For cost
reasons, the usual decision is the latter. This leads to the use
of surface coatings. Either the entire component can be
coated or just the area prone to attack, whichever best fulfills
the requirements.

1.1 Surface Properties

The necessary surface requirements for a component vary
considerably depending on its service environment.

The range of surface requirements include sufficient protec- Figure 1 a – Chrome plated, 13 / 4 steel pelton turbine nozzle needle after service.
tion against wear, corrosion resistance, thermal insulation,
electrical insulation, and even improved aesthetic
appearance.

In practice, it is quite rare that components are only exposed

to a single service condition. Usually a combination is pres-
ent; for example, abrasive wear combined with high thermal
stress. Various types of wear and corrosion are the most fre-
quent conditions the surface coating must withstand.

Figure 1b – Nozzle needle with a chrome oxide coating to prevent wear.

An Introduction to Thermal Spray – Issue 5 – October 20144

1.2 Coating processes coating materials; also, the necessary coating thicknesses
There are quite a number of processes to apply coatings, as are not attainable with all methods. Beyond that, the equip-
well as a nearly unlimited number of coating materials. To se- ment necessary for some processes can be quite complex
lect the correct combination for the respective application, and, therefore, costly. The use of cost analysis can determine
the knowledge of specialists is usually required. whether a coating is a practical solution. Today’s regulations
require that ecological criteria of the respective coating pro-
Table 1 lists principal coating processes, the typical coating cesses must also be examined, as not all methods are envi-
thicknesses attainable, common coating materials, and sam- ronmentally equal.
ple applications. Some processes are not suitable for certain

Coating process Typical coating thickness Coating material Characteristics Examples

PVD 1 – 5 μm (40 – 200 μin) Ti(C,N) Wear resistance Machine tools
CVD 1 – 50 μm (40 – 2000 μin) SiC Wear resistance Fiber coatings
Baked polymers 1 – 10 μm (40 – 400 μin) Polymers Corrosion resistance, ­aesthetics Automobile
Thermal spray 0.04 – 3 mm (0.0015 – 0.12 in) Ceramics and Wear resistance, Bearings
metallic alloys corrosion resistance
Hard chromium plate 10 – 100 μm (40 – 4000 μin) Chrome Wear resistance Rolls
Weld overlay 0.5 – 5 mm (0.02 – 0.2 in) Steel, stellite Wear resistance Valves
Galvanize 1 – 5 μm (40 – 200 μin) Zinc Corrosion resistance Steel sheet
Braze overlay 10 – 100 μm (40 – 4000 μin) Ni-Cr-B-Si alloys Very hard, dense surface Shafts
Table 1 a – Principal coating processes and characteristics

The coating process having the great- 1000

est range of coating materials, coating
CVD Welding
thicknesses and possible coating char- (Chemical Vapor Deposition)
acteristics is thermal spray. 800
Substrate temperature [°C]

600 PVD
(Physical Vapor
Deposition)
Thermal Spray Coatings
400

200
Ion
Implantation Chemical
Processes
0
0.1 1 10 100 1000 10000
Coating thickness [μm]

Table 1b – Coating process comparison

An Introduction to Thermal Spray – Issue 5 – October 20145

2 Thermal sprayed coatings

2.1 Definition 2.2 Substrate materials

Thermal spray is defined as [ 1 ]* “...applying these coatings Suitable substrate materials are those that can withstand
takes place by means of special devices / systems through blasting procedures to roughen the surface, generally having
which melted or molten spray material is propelled at high a surface hardness of about 55 HRC or lower. Special pro-
speed onto a cleaned and prepared component surface...” cessing techniques are required to prepare substrates with
This definition does not sufficiently describe the thermal higher hardnesses. Because the adhesion of the coating to
spray process. the substrate predominantly consists of mechanical bonding,
careful cleaning and pretreatment of the surface to be coat-
Figure. 2 is a diagram showing the principle of thermal spray. ed is extremely important.
The coating feedstock material is melted by a heat source.
This liquid or molten material is then propelled by process After the removal of surface impurities by chemical or me-
gases and sprayed onto a base material, where it solidifies chanical methods, the surface is usually roughened using a
and forms a solid layer. The individual aspects of a thermal blasting procedure. This activates the surface by increasing
sprayed coating follows. the free surface energy and also offers the benefit of in-
creased surface area for bonding of the sprayed particles.

The liquid or molten coating particles impact the surface

at high speed. This causes the particles to deform and
* Translated from German. spread like “pancakes” on the substrate.

Energy Feedstock material

Prepared
Spray gun Spray plume
surface

Gas or other operating media Relative motion Thermal sprayed coating

Figure 2 – Principle of thermal spraying

An Introduction to Thermal Spray – Issue 5 – October 20146

Heat from the hot particles is transferred to the cooler base performance. As most spraying materials are available as al-
material. As the particles shrink and solidify, they bond to the loys or blends, this leads to a nearly unlimited number of
roughened base material. Adhesion of the coating is there- combination options, and only through many years of experi-
fore based on mechanical “hooking”. This procedure is rep- ence and broad know-how can a proper selection be made.
resented schematically in Figures 2 and 3. The amount of
metallurgical bond caused by diffusion between the coating
particles and base material is small and can be neglected for
discussions about bonding mechanisms (exception:
Molybdenum).

Surface roughening usually takes place via grit blasting with

dry corundum. In addition, other media, such as chilled iron,
steel grit or SiC are used for some applications. Besides the
type of grit, other important factors include particle size, par-
ticle shape, blast angle, pressure and purity of the grit media. Oxide particle
Porosity

2.3 Coating material

In principle, any material that does not decompose as it is
melted can be used as a thermal spray coating material. De-
pending on the thermal spray process, the coating material
can be in wire or powder form.

In Table 2, some of the most frequently used classes of ma-

terials are listed, along with a typical example, characteristics
and sample applications. Choosing a coating material that is
suitable for a specific application requires special knowledge
about the service environment as well as knowledge about
the materials.

Apart from the physical characteristics, such as coefficient of

Substrate Unmelted particle
expansion, density, heat conductivity and melting point, ad-
ditional factors, such as particle shape, particle size distribu-
tion and manufacturing process of powder material (i.e., ag- Figure 3 – Schematic diagram of a thermal sprayed coating
glomerated, sintered, composited) will influence coating

Material class Example composition Characteristics Example application

Pure metals Zn Corrosion protection Bridge construction
Self-fluxing alloys FeNiBSi High hardness, fused, minimal porosity Shafts, bearings
Steel Fe 13Cr Economical, wear resistance Repair
MCrAlY NiCrAlY High temperature, corrosion resistance Gas turbine blades
Nickel-graphite Ni 25C Anti-fretting Compressor inlet ducts
Oxides Al2O3 Oxidation resistance, high hardness Textile industry
Carbides WC 12Co Wear resistance Shafts
Table 2 – Common classes of thermal spray powder materials

An Introduction to Thermal Spray – Issue 5 – October 20147

2.4 Thermal Spray coating processes
There are several different processes used to apply a thermal
sprayed coating [ 2 ]. They are:
nn Conventional flame spray,
nn Electric arc wire spray,
Plasma spray and
nn High velocity oxy-fuel spray (HVOF).

2.4.1 Conventional flame spray process

2.4.1.1 Combustion wire spray

Wire
With the combustion wire spray process, the wire spray ma-
Fuel gas Air cap
terial is melted in a gaseous oxygen-fuel flame. The fuel gas
can be acetylene, propane or hydrogen. The wire is fed con- Coating

centrically into the flame, where it is melted and atomized by

the addition of compressed air that also directs the melted
material towards the workpiece surface.

Oxygen Air passage Workpiece

Nozzle

Figure 4 a – Schematic diagram of the combustion wire spray process

2.4.1.2 Combustion powder spray

Powder
This coating process is based on the same operational prin-
ciple as the wire flame spray process, with the difference that Fuel gas Nozzle
the coating material is a spray powder. Thus, a larger selec- Coating

tion of spray materials is available, as not all spray materials

can be manufactured in wire form.

Oxygen Workpiece

Figure 4b – Schematic diagram of the combustion powder spray process

An Introduction to Thermal Spray – Issue 5 – October 20148

2.4.2 Electric Arc Wire Spray
With electric arc wire spray, an arc is formed by contact of
Voltage
two oppositely charged metallic wires, usually of the same
Compressed air
composition. This leads to melting at the tip of the wire Coating
material.

Air atomizes the melted spray material and accelerates onto

the substrate. The rate of spray is adjusted by appropriate
regulation of the wire feed as it is melted, so a constant arc
can be maintained.

Workpiece
Wire feed Wire guide
control

Figure 5 – Schematic diagram of the electric arc wire spray process

2.4.3 Plasma Spray

The principle of plasma spraying is shown schematically in
Plasma gas
Figure 6 a. A high frequency arc is ignited between an anode + current Water-cooled anode
and a tungsten cathode. The gas flowing through between Cathode
Coating
the electrodes (i.e., He, H2, N2 or mixtures) is ionized such
that a plasma plume several centimeters in length develops.
The temperature within the plume can reach as high as
16000° K. The spray material is injected as a powder outside
of the gun nozzle into the plasma plume, where it is melted,
and hurled by the gas onto the substrate surface.

Powder port Workpiece

Insulator

Figure 6 a – Schematic diagram of the plasma spray process

For specialized applications, a variant of the process is to

plasma spray in a controlled, low pressure atmosphere. In
contrast to coating in air (atmospheric plasma spraying,
or APS), the melted particles oxidize far less with vacuum
­plasma spraying (VPS), resulting in coatings of considerably
higher quality [ 3 ].

Figure 6 b – Controlled atmosphere plasma spraying

An Introduction to Thermal Spray – Issue 5 – October 20149

2.4.4 High Velocity Oxy-Fuel Spray (HVOF)
The high velocity oxy-fuel spray (HVOF) process is a relatively
recent addition to the family of thermal spray processes. As it Fuel gas Expansion nozzle
uses a supersonic jet, setting it apart from conventional Oxygen Coating
flame spray, the speed of particle impact on the substrate is
much higher, resulting in improved coating characteristics.
The mechanism differs from flame spraying by an expansion
of the jet at the exit of the gun (Figure 7). Fuel gases of pro-
pane, propylene, acetylene, hydrogen and natural gas can
be used, as well as liquid fuels such as kerosene. Diamond
shockwaves
Compressed air

Powder and carrier gas Workpiece

Figure 7 – Schematic diagram of the high velocity oxy-fuel spray

process (HVOF)

2.4.5 Process comparison

The processes previously discussed differ fundamentally by
the thermal and kinetic energy imparted to the spray parti-
cles by each process. The thermal energy is determined by
the attainable flame temperature and the kinetic energy of
the spray particle is a function of gas velocity. An energy Plasma
Thermal energy

comparison of the spray processes is represented in Figure

8. The high temperature of plasma spraying is particularly
suitable for materials with a high melting point, such as
ceramics. Electric Arc

The HVOF process, having high kinetic energy and compara-

tively low thermal energy, results in a positive effect on the Flame Spray HVOF
coating characteristics and is favorable for spray materials
such as tungsten carbide coatings. The comparison of the Kinetic energy
processes is largely of interest in relation to the coatings that
result. Table 3 lists some important coating characteristics,
organized by material class. Figure 8 – Energy comparison of thermal spray processes

An Introduction to Thermal Spray – Issue 5 – October 201410

Characteristics Coating type Combustion HVOF Electric arc Plasma
powder wire
Gas temperature [°C] 3000 2600 – 3000 4000 (Arc) 12000 – 16000
[°F] 5400 4700 – 5400 7200 (Arc) 21500 – 29000
Spray rate [kg / h] 2–6 1–9 10 – 25 2 – 10
[lb / h] 4.5 – 13 2 – 20 22 – 55 4.5 – 22
Particle velocity [m / s] ≤ 50 ≤ 700 ~ 150 ≤ 450
[ft / s] ≤ 160 ≤ 2300 ~ 500 ≤ 1500
Bond strength [MPa] Ferrous alloys 14 – 21 48 – 62 28 – 41 21 – 34
[psi] 2000 – 3000 7000 – 9000 4000 – 6000 3000 – 5000
[MPa] Non-ferrous alloys 7 – 34 48 – 62 14 – 48 14 – 48
[psi] 2000 – 5000 7000 – 9000 4000 – 7000 4000 – 7000
[MPa] Self-fluxing alloys 83+ (fused) 70 – 80 15 – 50 ---
[psi] 12000+ (fused) 10000 – 11500 2200 – 7200 ---
[MPa] Ceramics 14 – 34 --- --- 21 – 41
[psi] 4000 – 5000 --- --- 3000 – 6000
[MPa] Carbides 34 – 48 83+ --- 55 – 69
[psi] 5000 – 7000 12000+ --- 8000 – 10000
Coating thickness [mm] Ferrous alloys 0.05 – 2.0 0.05 – 2.5 0.1 – 2.5 0.4 – 2.5
[in] 0.002 – 0.080 0.002 – 0.100 0.004 – 0.100 0.015 – 0.100
[mm] Non-ferrous alloys 0.05 – 5.0 0.05 – 2.5 0.1 – 5.0 0.05 – 5.0
[in] 0.002 – 0.200 0.002 – 0.100 0.004 – 0.200 0.002 – 0.200
[mm] Self-fluxing alloys 0.15 – 2.5 0.05 – 2.5 --- ---
[in] 0.006 – 0.100 0.002 – 0.100 --- ---
[mm] Ceramics 0.25 – 2.0 --- --- 0.1 – 2.0
[in] 0.010 – 0.075 --- --- 0.004 – 0.080
[mm] Carbides 0.15 – 0.8 0.05 – 5.0 --- 0.15 – 0.8
[in] 0.006 – 0.030 0.002 – 0.200 --- 0.006 – 0.030
Hardness [HRC] Ferrous alloys 352030 – 6040 – 65 455530 – 60– 40 40
(see Table A1 in Non-ferrous alloys 35 50
the Appendix)
Self-fluxing alloys --- 30 – 60
Ceramics --- 45 – 65
Carbides 45 – 55 55 – 72 --- 50 – 65
Porosity [%] Ferrous alloys 3 – 10 <2 3 – 10 2–5
Non-ferrous alloys 3 – 10 <2 3 – 10 2–5
Self-fluxing alloys < 2 (fused) <2 --- ---
Ceramics 5 – 15 --- --- 1–2
Carbides 5 – 15 <1 --- 2–3
Table 3 – Comparison of thermal spray process coating characteristics (approximate values)

An Introduction to Thermal Spray – Issue 5 – October 201411

2.4.6 Infrastructure (system requirements) such as a turntable. Therefore, it is possible to apply coat-
Besides the principal item of a coating system, that of the ings to very complex geometries. The ventilation system with
spray gun, there are numerous other items necessary to ap- its filtering unit is not to be forgotten, as the so-called “over-
ply coatings in an industrial environment. Figure 9 shows a spray”, i.e. the powder material that does not stick to the
coating system. The spray cabin serves as a shield for the component surface, can be exhausted and trapped in the fil-
sound and dust produced by the spray gun during spraying. tering unit. The spray dust produced by some spray materi-
The cabin has inlet ports for the power, gas supply and the als can ignite; hence, in these situations, the entire system
process monitoring and control equipment. Usually, the gun must be fire and explosion proof. Figure 26 on page 21
is mounted on a robot, with movement programmed for the shows a modern, automated, high productivity coating
specific components to be coated. The component to be facility.
sprayed is usually mounted on a manipulation unit,

Water chiller Filter

Spray gun

Robot

Heat
exchanger

Electrical
supply cabinet

Spray cabin

Turntable

Plasma
power supply
Control console

Gas Management Center

Process Control Center

Powder feeder
Figure 9 – Typical coating facility

An Introduction to Thermal Spray – Issue 5 – October 201412

2.5 Coating structure One can produce much denser coatings with the HVOF
Thermal sprayed coatings exhibit a certain amount of pro- spray process. In Figure 11, a coating of WC (CoCr) is repre-
cess-dependant porosity. The highest porosity values devel- sented. There is hardly any porosity visible. The bright re-
op for flame and electric arc spray. HVOF coatings, however, gions consist of WC hard phase, which is embedded in a
produce very dense layers with porosity under 0.5 %. Typical ductile matrix of cobalt and chrome. Here the typical coating
plasma coatings have approximately one to two percent po- thickness is with 0.2 to 0.3 mm (0.008 to 0.012 inches).
rosity. Controlled atmosphere plasma spray can be near fully
dense. Thermal sprayed coatings generally exhibit high internal
stresses, which are attributable to the process of solidifica-
The sprayed coating develops as the spray gun traverses re- tion and cooling. The hot particle contracts as it cools, which
peatedly over the surface and applies the coating in layers, gives rise to the internal coating stress.
bit by bit; with a typical layer thickness of 10 to 20 μm (400
to 800 μin) . Oxides can form during the time between pass- If the ratio of the thermal expansion coefficients for the sub-
es on the outer surface of the layer. This oxidation can be strate material and the coating material are taken into ac-
minimized by spraying in a vacuum or inert atmosphere. count, these stresses can be compensated for
by producing compressive stresses. Temperature
Fine dust from overspray and unmelted particles can be- control during the coating process, therefore, plays an
come trapped in the coating. The dust is the result of coating mportant role to determine if the substrate must be cooled
material that does not adhere to the workpiece during spray- or warmed.
ing. Subsequent spray passes drag these particles towards
the coating surface where they become trapped in the coat- Sometimes, the adhesion of a ceramic coating on a sub-
ing layer. strate does not meet the necessary requirement for bond
strength. In order to increase the bond strength, a bond coat
Figure 10 shows a photomicrograph of an arc sprayed coat- is applied, usually composed of a NiAl or NiCr alloy, which
ing of X40 CR 13. One recognizes the laminated structure acts as an intermediate layer between the substrate and the
and existing porosity (the black regions). The circular parti- ceramic coating. Such intermediate coatings can also per-
cles are those that did not melt completely before resolidify- form another important function by providing additional cor-
ing. The thickness of this coating can be to up to several rosion protection.
millimeters.

Figure 10 – Arc wire spray coating of X40 steel Figure 11 – HVOF spray coating of WC 12(CoCr)

An Introduction to Thermal Spray – Issue 5 – October 201413

2.6 Coating characteristics 2.7.1 Mechanical post processing
As previously stated, the porosity of a thermal spray coating Thermal sprayed coatings possess a rough surface
is process-dependant, and exhibits an anisotropic, layered that is between 5 and 20 μm (see Table A2 in the
structure. These basic characteristics can be modified within Appendix). Therefore, it will often be necessary to
a wide range to suit the specific application. machine many components to achieve a final dimension
and surface finish. Depending on the coating applied,
2.6.1 Wear protection the surface can be worked by conventional machining
One of the most important uses of thermal sprayed coatings or can be ground and lapped to final dimension.
is for wear protection [ 4 ]. In these applications, ceramics,
and above all, carbide materials are used. The commonly 2.7.2 Sealing
used carbide materials are WC / Co or WC / CoCr. Here, the Sealing sprayed coatings serves primarily to fill the
carbide hard phases (WC) exhibit excellent resistance pores and microcracks in the coating, which provides addi-
against abrasive and erosive wear, and are embedded in a tional protection against corrosive media that would other-
ductile matrix of cobalt. wise penetrate to the base material.

2.6.2 Corrosion protection When resin or wax sealants are used, those in a liquid
Low carbon, unalloyed steel and cast iron materials are sus- condition penetrate into the pores and then harden
ceptible to rust and therefore often need constant surface (usually with heating). If the sealant is sprayed or painted
protection. This can be produced by flame sprayed coatings on, the procedure may have to be repeated several
of aluminum or zinc. The main areas of application are for times to insure complete coverage.
bridges the offshore structures. For high temperature appli-
cations, protective coatings of MCrAlY materials can be Sealants can also be used to provide surfaces with non-ad-
used. These are usually applied using controlled atmosphere hesive characteristics (PTFE based sealers).
plasma spray.
2.7.3 Post-coat heat treatment
2.6.3 Insulative coatings (thermal / electrical) With thermal post-coat treatments, one differentiates be-
Ceramic materials are excellent thermal and electrical insula- tween diffusion to increase the coating bond to the base ma-
tors. They also possess good oxidation and wear resistance. terial versus fusing of “self-fluxing” alloys.
These characteristics are quite useful on engine and turbine
components as thermal barrier coatings. The thermal barrier Self-fluxing alloys form a special class of spray materials in
coating lowers the skin temperature of the substrate, thereby that after the spray coating is applied, an additional step of
extending the useful service life. On the other hand, efficien- fusing the coating is employed. The spray materials are gen-
cy is improved as a result of reduced heat loss at the same erally alloys of chromium, iron and nickel that contain a sub-
operating temperature. These coating systems consist of a stantial amount of temperature suppressants, such as boron
bond coat, which is usually an oxidation resistant MCrAlY and silicon.
material (M = Fe, Ni or Co) and a ceramic top coat. A yttri-
um-stabilized zirconium oxide material is often used for the During the spray process, there is some partial formation of
top coat because of its good thermal shock characteristics. intermetallic phases. Subsequent fusing of the coating caus-
es a complete transformation of the materials and the forma-
2.7 Post processing tion of hard silicide and boride phases. Diffusion into the
Because many sprayed coatings have an inherently rough substrate also occurs, improving bonding. Porosity is nearly
surface finish and porosity, it is frequently necessary to post eliminated, with no interconnecting porosity.
process the surface. In addition, specification procedures
can call for other methods, such as post-coating diffusion, These coatings exhibit extremely good corrosion resistance
nitrating, hot isostatic pressing or shot peening, as required. as well as very high hardness. The common manual method

An Introduction to Thermal Spray – Issue 5 – October 201414

used to melt the coating is through the use of an acetylene nn Cross-sectioning for the determination of precise coating
torch. Fusing in a furnace, with laser, electron beam or with thickness, porosity, microstructure, and examination for
induction heating is also possible. The temperature required unmelted particles and oxide inclusion
to effect diffusion is in the range of 1000 to 1200 °C (1800 to nn Microhardness and / or macrohardness measurement
2200 °F). nn Bond strength determination
nn Bend tests
In Figure 12, just such a coating of a NiCrBSi alloy is shown
before and after fusing of the coating. The homogenization of The test measurements use standardized sample geome-
the coating structure is clearly recognizable, as is the re- tries. Exact execution and interpretation is in accordance
duced porosity and dense nature of the fused coating. with various standards [ 6 ]. Beyond that, there are many other
possibilities. The characterization of coatings in practice is
2.8 Coating characterization quite complex, and there are many different procedures that
Apart from the coating characteristics that are important with are not common.
respect to the application, there are some characteristics
that can be determined with relatively little effort and can be In addition, other tests can be included such as various
accomplished in terms of standardized quality control mea- methods for elemental analysis, scratch testing, tribological
surements. These are: investigations, stress analysis, corrosion characterization and
nn Visual inspection abrasion behavioral investigations. Since these are all de-
nn Coating thickness measurement structive examinations, they are not especially usable for pro-
nn Surface finish measurement duction and are rarely employed on test pieces. Many end
users have developed their own specifications and test
If necessary, test pieces, sprayed at the same time and un- methods to characterize and judge the quality of their coat-
der the same conditions as the coating, can be examined to ings. In particular, the aerospace and automotive industries
determine additional coating characteristics: have very strict guidelines.

Coating structure after fusing Coating structure after coating

Figure 12 – Self-fluxing coating

An Introduction to Thermal Spray – Issue 5 – October 201415

3 Applications
In order to use thermal sprayed coatings to best advantage, The preferred geometries for coatings are disks, flat panels
the coating material has to be properly selected, the coating and rotationally symmetrical components, as illustrated in
process has to be chosen and the process parameters de- Figure 13.
veloped. Also, the component to be coated has to be cor-
rectly dimensioned for coating.

Not feasible Feasible Preferred configuration

2 mm (0.08 in)
simplified structure
R > 3t

t 30°

30°

5 mm (0.2 in) 5 mm (0.2 in) t

> 20 mm 3t
(0.75 in)

< 50 mm (2 in)

50 – 80 mm (2 – 3.2 in) > 80 mm (3.2 in)

with special spray gun,
quality is reduced

Figure 13 – Favorable coating geometries for coating

An Introduction to Thermal Spray – Issue 5 – October 201416

3.1 Production applications

3.1.1 Hard chromium alternative

Thermal sprayed HVOF coatings can be used as an alterna-
tive to hard chromium plating to provide wear and corrosion
protection using pure chromium and various carbide coat-
ings [ 5 ]. The characteristics of HVOF coatings, in part, ex-
ceed those of chromium plate and HVOF processing times
are generally significantly shorter. The reflective surface ap-
pearance of hard chromium plating can be achieved by
grinding and lapping the HVOF coating. An example applica-
tion where thermal spray is used to replace hard chromium
plate is that of aircraft landing gear components, as shown in
Figure 14. Figure 14 – Nose gear of an F5 Tiger with a WC / CoCr coating

3.1.2 Medical implants

For strong and durable anchoring of orthopedic implants,
such as artificial hip joints, surface finish is of great impor-
tance. Oerlikon Metco's Metco™PLANT coatings, applied
using the vacuum plasma process, are purposely sprayed
with a very fissured surface that allows the bone to grow into
it. There are Metco™PLANT coatings that act as a biocom-
patible titanium coating (Figure 15), or bioactive hydroxy apa-
tite coatings, which actively accelerates the growth of the
natural bone into the surface of the prosthesis.

3.1.3 Textile machinery

Metco™TEX coating systems were developed as the result of
many years of cooperation with textile machinery manufac-
turers. These coatings are characterized by a precise defini-
tion of the morphology produced using various handling
methods and the topology of the surface. The surface tex-
ture is of particular importance for production components in Figure 15 – Biocompatible Metco™PLANT titanium coating on a hip implant
contact with thread. In order to maximize fiber production,
coatings of ceramic oxides are used, usually with a nickel
bond coat that provides corrosion protection. Sample appli-
cations are represented in Figure 16.

Figure 16 – Various textile machinery components

An Introduction to Thermal Spray – Issue 5 – October 201417

3.1.4 Gas turbines
In both stationary and flight gas turbines, thermal sprayed
coatings are used in many different places and for many dif-
ferent functions. Protective coatings for high temperature
corrosion resistance, thermally insulating coatings, clearance
control coatings and the repair of superalloy components
with coatings of similar composition are just some examples
(see Figure 17).

3.1.5 Printing industry

Coated rollers and cylinders are used extensively for printing
machinery. In partnership with customers from the paper and
printing industry, several Metco™PRINT coatings were devel-
oped. Plasma sprayed chraome oxide coatings for inking
rollers exhibit very fine microstructures, which can then be la-
ser engraved with a very small and tight pattern (Figure 18). Figure 17 – Coated gas turbine vanes

3.1.6 General industrial uses

The largest variety of applications is for the machinery indus-
try. Figure 19 shows a bearing shaft coated with a babbitt
coating used in cement plants.

This special, particularly porous coating is designed for oil lu-

brication, providing a reservoir to prevent seizure.

Other examples of applications are piston rings for diesel en-

gines, piston rods in compressors, pump bearings, valve
covers, etc.

Figure 18 – Anilox printing roll with a laser engraved Metco™PRINT coating

Figure 19 – Bearing shaft with a babbitt coating

An Introduction to Thermal Spray – Issue 5 – October 201418

3.1.7 Consumer goods
Although most uses for thermal spray coatings were devel-
oped for very specialized components, there are also appli-
cations within the consumer goods industry. An iron sole
plate, on which a ceramic coating was applied as protection
from wear is shown in Figure 20. A coating of an anti-stick
material is subsequently applied. Similar coatings are also
applied to non-stick frying pans.

3.1.8 Automotive industry

Next to the coating of numerous small parts, the newest
breakthrough development for Oerlikon Metco is coatings for
aluminum engine blocks. The cylinder bores of the engines
are coated by means of a special rotating plasma gun ma-
nipulator (Figure 21), which can apply the coating to the inte- Figure 20 – Coated household steam iron soleplate
rior of the small bores with a wear resistant surface.

3.1.9 Steel industry

The rolls used in the steel working industry must handle very
heavy thermal loads of hot steel. In addition, slag from steel
production must be reckoned with, and in zinc production,
corrosive attack from the molten zinc. Several different
Metco™STEEL coating systems have been qualified for use
on both new parts and repair applications. (Figure 22)

Figure 21 – Dual-RotaPlasma™

Figure 22 – HVOF coating of a sink roll

An Introduction to Thermal Spray – Issue 5 – October 201419

3.1.10 Paper industry
Rollers in the paper industry are subject to the most diverse
of operating environments including wear, chemical attack
from dyes, thermal stress on heated rollers and mechanical
stress from doctor blades. At the same time, they must ex-
hibit a high surface finish over as long a length of time as
possible. The Metco™CAL coatings were developed to meet
these requirements, particularly for calendar rolls (Figure 23).

3.1.11 Aerospace
Besides those components already mentioned for gas tur-
bines, there are additional coatings used on airplanes. Figure
24 shows a coating on the interior of a combustion chamber.

3.2 Salvage and restoration

Thermal spray can be used also in repair procedures to re- Figure 23 – Metco™CAL coating after superfinishing
store components to their original dimensions. The coatings
can be turned or ground to finished size. Ni-Cr, Ni-Al or
Ni-Cr-Al are used as repair materials for alloyed steels.

Figure 24 – Combustion Chamber

Figure 25 – Repair procedure

An Introduction to Thermal Spray – Issue 5 – October 201420

Figure 26 – A modern LPPS high-volume production system for coating gas turbine blades

4 Summary
With thermal spray, probably more so than any other coating With our unsurpassed in-house knowledge in the design and
process, there is almost no limitation in the number of op- construction of thermal spray systems, equipment and mate-
tions available for substrate and coating material combina- rials, as well as many years of coating experience for both
tions. As a result, thermal spray coatings lend themselves to prototype and production components, Oerlikon Metco is
a broad scope of applications, both for new component the ideal partner for all thermal spray needs.
manufacture and for repair. The characteristics of the coat-
ings can be varied within a wide range to suit specific appli- Please contact your Oerlikon Metco account representative
cation requirements. This presupposes, however, the many for further information or visit us on the web at
years of experience and the know-how of specialists. www.oerlikon.com/metco.

An Introduction to Thermal Spray – Issue 5 – October 201421

5 Appendix

5.1 Reference tables

Rockwell Vickers Brinell Tensile strength Rockwell Vickers Brinell Tensile strength
HRC HV HB Rm [N / mm2] HRC HV HB Rm [N / mm2]
80 1865 43 423 399 1350
79 1787 42 412 390 1320
78 1710 41 402 380 1290
77 1633 40 392 371 1255
76 1556 39 382 361 1220
75 1478 38 372 352 1190
74 1400 43 423 399 1350
73 1323 42 412 390 1320
72 1245 41 402 380 1290
71 1160 40 392 371 1255
70 1076 39 382 361 1220
69 1004 38 372 352 1190
68 942 43 423 399 1350
67 894 42 412 390 1320
66 854 41 402 380 1290
65 820 40 392 371 1255
64 789 39 382 361 1220
63 763 38 372 352 1190
62 746 37 363 340 1150
61 720 36 354 335 1140
60 697 35 345 330 1115
59 674 34 336 323 1095
58 653 620 2180 33 327 314 1060
57 633 599 2105 32 318 304 1030
56 613 580 2030 31 310 295 995
55 595 570 1995 30 302 285 965
54 577 551 1920 29 294 280 950
53 560 532 1845 28 286 271 915
52 544 515 1780 27 279 266 900
51 528 495 1700 26 272 257 865
50 513 485 1665 25 266 252 850
49 498 475 1630 24 260 247 835
48 484 456 1555 23 254 242 820
47 471 447 1520 22 248 238 800
46 458 437 1485 21 243 233 785
45 446 423 1450 20 238 228 770
44 434 409 1385
Table A1 – Hardness within the range HRC 80 to 20 (approximate cross-reference values)

An Introduction to Thermal Spray – Issue 5 – October 201422

Surface Finish Ra [μm] Ra [μin] Rz [μm] Surface Finish Ra [μm] Ra [μin] Rz [μm]
N0 0.0125 0.5 N7 1.6 64 7.87
N1 0.025 0.1 0.29 N8 3.2 128 15.6
N2 0.05 2 0.55 N9 6.3 250 40
N3 0.1 4 0.91 N10 12.5 500 63
N4 0.2 8 1.74 N11 25 1000 100
N5 0.4 16 2.6 N12 50 2000 160
N6 0.8 32 4.65
Table A2 – Surface finish (approximate cross-reference values)

5.2 Literature references

[1] DIN EN 657; Thermal Spray – Begriffe, Einteilung; Beuth-Verlag, Berlin (1994)
[2] H.D. Steffens, J. Wilden: “Moderne Beschichtungsverfahren”, DGM-Verlag, ISBN 3-88355-223-2, (1996)
[3] P. Huber: “Vakuumplasmaspritzen”, oberfläche surface, 10 (1992), 8
[4] H. Simon, M. Thoma: “Angewandte Oberflächentechnik für metallische Werkstoffe”, Hanser-Verlag, München (1985)
[5] E. Lugscheider. H. Reymann: «Hochgeschwindigkeitsflammgespritzte Chromschichten zum Verschleiss-und Korrosionsschutz»,
Schweissen und Schneiden, 50 (1998), 44
[6] DIN 50600; Metallographische Gefügebilder, Beuth-Verlag, Berlin
DIN EN 582 Ermittlung der Haftzugfestigkeit, Beuth-Verlag, Berlin (1994)
DIN EN 10109 Teil 1; Härteprüfung, Beuth-Verlag, Berlin (1995)

DVS 2310 Teil 2; Anleitung zur Schliffherstellung, DVS, Düsseldorf, (1989)

An Introduction to Thermal Spray – Issue 5 – October 201423

Thermal Spray
Advanced Technology Solutions and Services

Perfect solutions through

optimum materials and innovative
technologies
Oerlikon Metco is a global leader in Oerlikon Metco provides a comprehensive
surface engineering solutions and manufacturing, distribution and service
services offering: network, catering to aviation, power
nn A broad range of thermal spray, thin generation, automotive and other strategic
film, laser cladding and other growth industries.
advanced surface technology
equipment and materials To take control of your surface engineering
nn Integrated systems challenges, contact your Oerlikon Metco
nn Specialized coating and surface sales office, visit our web site at
enhancement services www.oerlikon.com/metco or e-mail us at
nn Manufactured components for the info.metco@oerlikon.com.
turbine, automotive and other
industries
nn Customer support services

About Oerlikon Metco

Oerlikon Metco enhances surfaces that bring benefits to customers through a
uniquely broad range of surface ­technologies, equipment, materials, services,
specialized machining services and components. The surface techno­logies such
as Thermal Spray, Thin Film, Plasma Heat Treatment and Laser Cladding improve
the performance ­and ­increase efficiency and reliability. Oerlikon Metco serves in-
dustries such as aviation, power generation, automotive, oil & gas, industrial and
other specialized markets and operates a dynamically growing network of more
than 50 sites in EMEA, Americas and Asia Pacific. Oerlikon Metco, together with
Oerlikon Balzers, ­belongs to the Surface Solutions Segment of the Switzerland-­
based Oerlikon Group.

Information is subject to change without prior notice.

www.oerlikon.com / metco
An Introduction to Thermal Spray – Issue 5 – October 201424
info.metco@oerlikon.com