®

QR-25 Series
Model 340

Parts Manual
Record of Change 107

This manual contains important safety information and must be made

available to all personnel who operate and/or maintain this product.
Carefully read this manual before attempting to operate or perform
maintenance on this compressor.

Fill Out & Return Warranty Registration Card Located Inside

Manual No. 50216-107

August 2010 Edition

INTRODUCTION TABLE OF CONTENTS
This manual provides information for the following Serial Number Identification ................................. 2
QR-25 Series, Model 340 (Record of Change 107)
compressor versions: Ordering Replacement Parts ................................ 2
Quin-Cip Lubricant ................................................ 2
L Control Version L
head assembly with 2 unloader towers & Crankcase Lubricant Capacity ............................. 2
a hydraulic unloader Crankshaft Group .................................................. 3
Crankcase Group ................................................... 4
LS Control Version LS
head assembly with 2 unloader towers, a Bearing Carrier Groups
hydraulic unloader, & a pilot valve with with oil filter ..................................................... 5-6
a check valve assembly less oil filter ..................................................... 7-8
Connecting Rod & Piston Groups
LVD Control Version LVD low pressure .................................................. 9-10
head assembly with 2 unloader towers, a high pressure .............................................. 11-12
hydraulic unloader, & a pilot valve with
Cylinder & Head Groups
a lockout & check valve
Control Versions L, LS, LVD ............................ 13
These compressors are aircooled, two stage, two Head Assemblies
cylinder, pressure lubricated compressors, with up Control Versions L, LS, LVD ............................ 14
to 200 PSI continuous pressure capability (201 to 500 Suction Valve Assembly ..................................... 15
PSI intermittent pressure capability with proper
configuration; consult factory). The Model 340 has a Discharge Valve Assembly ................................. 16
5-1/4" low pressure bore, a 3" high pressure bore, a Unloader Assembly ............................................. 17
3-1/2" stroke and can be run at 400-900 RPM. Pneumatic Unloader Assembly .......................... 18
Available options included in this manual: Control Groups
-hooded air filter Version L ........................................................... 19
-hooded air filter / silencer Version LS ................................................... 20-21
-high pressure rated cylinder and head Version LVD ................................................. 23-24
Pilot Valves .......................................................... 24
Pilot Valve Repair Kit .......................................... 24
CHANGES Differential Setting Charts .................................. 24
since previous printing dated October 2006:
Suction Valve Unloader Assemblies .................. 25
The compressor sheave was changed from a 3- Check Valve Assemblies ..................................... 25
groove design to a 4-groove design. Hydraulic Unloader Assemblies ......................... 26
Decals ................................................................... 27
Gasket Set ............................................................ 27
Recommended Spare Parts ................................ 27
Kits ....................................................................... 27
Typical Unit Repair Parts List ............................. 28

QR 340 Quincy Compressor

50216-107, August 2010 1 3501 Wismann Lane, Quincy IL. - 62305-3116

MODEL & QUIN-CIP LUBRICANT ®

Refer to the chart below to order Quin-Cip compres-

SERIAL NUMBER sor lubricant from your local authorized Quincy
Record
IDENTIFICATION of
distributor.
Change No. Package Part No. Description
Barrel 112541D032 55 gal., SAE 10W
Pail 112541P032 5 gal., SAE 10W
Gallon 112541G032 1 gal., SAE 10W
Gallon Case 112541X032 (4)-1 gal., SAE 10W
Quart 112541Q032 1 qt., SAE 10W
Quart Case 112541C032 (12)-1 qt., SAE 10W

Barrel 112542D068 55 gal., SAE 20

Pail 112542P068 5 gal., SAE 20
Gallon 112542G068 1 gal., SAE 20
Model & Serial Number Gallon Case 112542X068 (4)-1 gal., SAE 20
Identification Tag Quart 112542Q068 1 qt., SAE 20
Quart Case 112542C068 (12)-1 qt., SAE 20
The model & serial number tag is located on the
handhole plate side of the crankcase. Fill in the Barrel 112543D100 55 gal., SAE 30
numbers from your compressor's tag in the corre- Pail 112543P100 5 gal., SAE 30
sponding spaces provided here and reference this Gallon 112543G100 1 gal., SAE 30
page when ordering replacement parts. Gallon Case 112543X100 (4)-1 gal., SAE 30
Quart 112543Q100 1 qt., SAE 30
All replacement parts are to be ordered through Quart Case 112543C100 (12)-1 qt., SAE 30
an authorized Quincy distributor. Insist on genuine
Quincy parts only! Failure to do so may void war-
ranty.
CRANKCASE LUBRICANT
CAPACITY
Model Less Filter With Filter

QR-340 43/4 qts. (4.5 lit.) Add 10 oz. (296 ml)

ORDERING CAUTION !
REPLACEMENT PARTS Refer to the QR-25 Series Instruction Manual for vital
lubrication information.
Prompt service can be rendered on repair parts
orders if the following information is given:
CAUTION !
Item 1) the model number, record of change Follow all safety precautions outlined in the QR-25 Series
number, & serial number. instruction manual.
Item 2) the exact part number needed. (Do not
order by item numbers.)
Item 3) the exact quantity needed. WARNING !
Do not operate this compressor without a totally enclosed
Item 4) the preferred type of transportation belt guard or any other required safety equipment.

DANGER !
Air used for breathing or food processing must meet OSHA
1910.134 or FDA 21 CFR 178.3570 regulations. Failure to

QR 340 Quincy Compressor

50216-107, August 2010 2 3501 Wismann Lane, Quincy IL. - 62305-3116

CRANKSHAFT GROUP 110524
Item Part
Number Qty. Number Description
1 1 110519 crankshaft assembly includes:
1.1 1 110518R crankshaft
1.2 1 2788 bearing cone
1.3 1 40775 bearing cone
1.4 1 110234 orifice, 1/8 npt
1.5 2 121160 pipe plug, 1/8 npt
1.6 1 110705-F17 roll pin, 3/16 x 1.38
2 1 110523X sheave assembly includes:
2.1 1 110523 sheave, 19-1/2", 4 gr, B sect., CCW (N.S.S.: order 110523X)
2.2 2 110983-N22 hex. screw, 1/2-13 unc x 3.25, grade 8 (@ 90 ft.-lbs.)
2.3 2 116124-N02 square nut, 1/2-13 unc
2.4 2 110428N050 flatwasher, 1/2
3 1 1466 taper key

N.S.S. = Not Sold Separate

@ Indicates torque value in foot pounds (dry threads)
For reversal of compressor rotation refer to QR-25 instruction manual.

QR 340 Quincy Compressor

50216-107, August 2010 3 3501 Wismann Lane, Quincy IL. - 62305-3116

 CRANKCASE GROUP 110628
Item Part
Number Qty. Number Description
1 1 6904X crankcase assembly
1.1 1 6904R crankcase (N.S.S.; order 6904X)
1.2 1 3720 bearing cup
2 1 2057 pipe plug, 1/2 npt
3 * 1383 bearing adjustment shim, .005 steel
4 * 1383A bearing adjustment shim, .007 steel
5 * 1383B bearing adjustment shim, .020 steel
6 * 1383D bearing adjustment shim, .002 steel
7 1 6930 adjustment plate (.0015 / .003 crankshaft end play)
8 4 123478-L12 hex. screw, 3/8-16 unc x 1.00, grade 5 (@ 30 ft.-lbs.)
9 2 1315 inspection plate gasket
10 1 1249-1 inspection plate
11 1 6849-2 inspection plate
12 12 123478-K12 hex. screw, 5/16-18 unc x 1.00, grade 5 (@ 12 ft.-lbs.)
13 1 111876-2 dipstick
14 1 5783 breather ball
15 1 5932 drive pin
16 12 110428N031 flatwasher, 5/16
17 1 112033-908 "o"ring, 3/32 wide x .82 o.d.
Maintenance Parts
1 6930-1X Replacement Adjustment Plate Assembly
(includes adjustment plate & oil seal)

N.S.S. = Not Sold Separate

@ Indicates torque value in foot pounds (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross pattern. Bring
each fastener to the recommended torque specification in even increments.
* Quantity as required.

QR 340 Quincy Compressor

50216-107, August 2010 4 3501 Wismann Lane, Quincy IL. - 62305-3116

BEARING CARRIER GROUP 110820-001
(with oil filter)

QR 340 Quincy Compressor

50216-107, August 2010 5 3501 Wismann Lane, Quincy IL. - 62305-3116

 BEARING CARRIER GROUP 110820-001
(with oil filter)

Item Part
Number Qty. Number Description
*1 1 110812-003 bearing carrier assembly
1.1 1 110812 bearing carrier assembly
includes:
1 2720 bearing cup
2 160005 bronze bushing
* 1.2 1 123157-152 "o"ring, 3/32 wide x 3.44 o.d.
* 1.3 1 123157-112 "o"ring, 3/32 wide x .69 o.d.
1.4 1 160002-001 bearing carrier driveshaft
1.5 1 160075-001 driveshaft key
1.6 1 160003 pump gerotor
1.7 1 6285 retaining ring
1.8 1 110813-001 oil pump housing
1.9 6 123777-J12 hex screw, 1/4-20 unc x 1.00, grade 5 (@ 6 ft.-lbs.)
1.10 2 2719 pipe plug, 1/4 npt
1.11 1 5489 adjustment screw
* 1.12 1 123157-011 "o"ring, 1/16 wide x .44 o.d. (oil pressure adjustment screw)
1.13 1 124369-P02 jamnut, 9/16-18 unf
1.14 1 1160 spring
1.15 1 112857 needle valve
1.16 1 2755S pipe plug, 1/8 npt
2 1 5502 bearing carrier gasket
3 8 123478-L12 hex. screw, 3/8-16 unc x 1.00, grade 5 (@ 30 ft.-lbs.)
§4 1 110822 oil pressure gauge
5 1 6679 gasket, oil inlet bracket
6 1 110659 oil pickup tube
7 2 123115-06C lockwasher, 3/8
8 2 123478-L11 hex. screw, 3/8-16 unc x .88, grade 5 (@ 30 ft.-lbs.)
9 1 110825 oil filter stud

Maintenance Parts
* 10 110814-001 oil filter (six pack)
160079 Oil Pump Repair Kit
(includes 1 each of items 1.2, 1.3, 1.4, 1.5, 1.6, 1.7, & 1.12)
110812X003 Replacement Bearing Carrier Assembly
(includes 1 each of items 1, 2, 5, 9, & 1 oil filter)

* Can not be used with diester or phosphate ester based synthetic lubricants.
§ Install with Teflon® tape.

QR 340 Quincy Compressor

50216-107, August 2010 6 3501 Wismann Lane, Quincy IL. - 62305-3116

BEARING CARRIER GROUP 110820
(less oil filter)

QR 340 Quincy Compressor

50216-107, August 2010 7 3501 Wismann Lane, Quincy IL. - 62305-3116

 BEARING CARRIER GROUP 110820
(less oil filter)
Item Part
Number Qty. Number Description
1 1 110812-002 bearing carrier assembly
1.1 1 110812 bearing carrier assembly
includes:
1 2720 bearing cup
2 160005 bronze bushing
* 1.2 1 123157-152 "o"ring, 3/32 wide x 3.44 o.d.
* 1.3 1 123157-112 "o"ring, 3/32 wide x .69 o.d.
1.4 1 160002-001 bearing carrier driveshaft
1.5 1 160075-001 driveshaft key
1.6 1 160003 pump gerotor
1.7 1 6285 retaining ring
1.8 1 110813 oil pump housing
1.9 6 123777-J12 hex screw, 1/4-20 unc x 1.00, grade 5 (@ 6 ft.-lbs.)
1.10 2 2719 pipe plug, 1/4 npt
1.11 1 5489 adjustment screw
* 1.12 1 123157-011 "o"ring, 1/16 wide x .44 o.d. (oil pressure adjustment screw)
1.13 1 124369-P02 jamnut, 9/16-18 unf
1.14 1 1160 spring
1.15 1 112857 needle valve
2 1 5502 bearing carrier gasket
3 8 123478-L12 hex. screw, 3/8-16 unc x 1.00, grade 5 (@ 30 ft.-lbs.)
§ 4 1 110822 oil pressure gauge
5 1 6679 gasket, oil inlet bracket
6 1 110659 oil pickup tube
7 2 123115-06C lockwasher, 3/8
8 2 123478-L11 hex. screw, 3/8-16 unc x .88, grade 5 (@ 30 ft.-lbs.)

Maintenance Parts
160079 Oil Pump Repair Kit
(includes 1 each of items 1.2, 1.3, 1.4, 1.5, 1.6, 1.7, & 1.12)
110812X002 Replacement Bearing Carrier Assembly
(includes 1 each of items 1, 2, & 5)

* Can not be used with diester or phosphate ester based synthetic lubricants.
§ Install with Teflon® tape.

QR 340 Quincy Compressor

50216-107, August 2010 8 3501 Wismann Lane, Quincy IL. - 62305-3116

CONNECTING ROD & PISTON GROUP 110749
(low pressure)

1.2 RING GAPS TO BE STAGGERED

WHEN ASSEMBLED.
PIP MARKS INDICATE
6 TOP SURFACE OF RING.

1.3 6

2
7
1.1 4

1.4
3

8
2

QR 340 Quincy Compressor

50216-107, August 2010 9 3501 Wismann Lane, Quincy IL. - 62305-3116

 CONNECTING ROD & PISTON GROUP 110749
(low pressure)
Item Part
Number Qty. Number Description
1 1 40081 connecting rod assembly (N.S.S.; order 6655X)
1.1 1 110802R connecting rod (N.S.S.; order 6655X)
1.2 1 6443 connecting rod bearing (N.S.S.; order 6443SR)
1.3 2 1344 connecting rod bolt, 7/16-20 unc x 3.25
1.4 2 1319 connecting rod bolt washer
2 2 8648 retaining ring
3 1 110146 piston pin
4 1 8642 piston
5 1 2033 oil ring
6 3 9666 piston ring
7 2 6656 connecting rod insert (sold in pairs only; see maintenance parts)
8 2 124471-M08 locknut, 7/16-20 unf (@ 40 ft.-lbs.)

Maintenance Parts
7 1 6656PR inserts, connecting rod (1 pair, standard size)
7 1 6656-010PR inserts, connecting rod (1 pair, .010 undersize)
1.2 1 6443SR replacement connecting rod bearing
4 1 8642-010 piston, low pressure (.010 oversize)
4 1 8642-020 piston, low pressure (.020 oversize)
1 7595A Piston Ring Set (standard)
includes piston rings & oil ring
1 4450-010 Piston Ring Set (.010 oversize, light blue color code)
includes includes piston rings & oil ring
1 4450-020 Piston Ring Set (.020 oversize, yellow color code)
includes includes piston rings & oil ring
1 8642X Piston Assembly, low pressure (standard)
includes ring set, piston pin, retaining rings, & piston
8642X010 Piston Assembly, low pressure (.010 oversize)
includes ring set, piston pin, retaining rings, & piston
8642X020 Piston Assembly, low pressure (.020 oversize)
includes ring set, piston pin, retaining rings, & piston
6655X Replacement Connecting Rod Assembly
includes connecting rod assembly, connecting rod inserts, & locknuts

N.S.S. = Not Sold Separate

@ Indicates torque value in foot pounds (dry threads)

QR 340 Quincy Compressor

50216-107, August 2010 10 3501 Wismann Lane, Quincy IL. - 62305-3116

CONNECTING ROD & PISTON GROUP 110750
(high pressure)

RING GAPS TO BE STAGGERED

WHEN ASSEMBLED.
PIP MARKS INDICATE 7
TOP SURFACE OF RING.

1.2
7

1.3
5

1.5

8
1.1
4

3
1.4

QR 340 Quincy Compressor

50216-107, August 2010 11 3501 Wismann Lane, Quincy IL. - 62305-3116

 CONNECTING ROD & PISTON GROUP 110750
(high pressure)
Item Part
Number Qty. Number Description
1 1 110804 connecting rod assembly (N.S.S.; order 110804X)
1.1 1 110802 connecting rod (N.S.S.; order 110804X)
1.2 2 110799-010 needle bearing
1.3 2 1344 connecting rod bolt, 7/16-20 unc x 3.25
1.4 2 1319 connecting rod bolt washer
1.5 1 110801-001 orifice plug
2 2 8648 retaining ring
3 1 110190-008 piston pin
4 1 2008-001 piston
5 2 6451 oil ring rail
6 1 6450 expander ring
7 3 1648 piston ring
8 2 6656 connecting rod insert (sold in pairs only; see maintenance parts)
9 2 124471-M08 locknut, 7/16-20 unf (@ 40 ft.-lbs.)

Maintenance Parts
8 1 6656PR inserts, connecting rod (1 pair, standard size)
8 1 6656-010PR inserts, connecting rod (1 pair, .010 undersize)
4 1 2008-011 piston, high pressure (.010 oversize)
4 1 2008-021 piston, high pressure (.020 oversize)
1 6452A Piston Ring Set (standard)
includes piston rings, oil ring rails & expander
1 4425-010 Piston Ring Set (.010 oversize, light blue color code)
includes includes piston rings, oil ring rails & expander
1 4425-020 Piston Ring Set (.020 oversize, yellow color code)
includes includes piston rings, oil ring rails & expander
1 2008X001 Piston Assembly, high pressure (standard)
includes ring set, piston pin, retaining rings, & piston
2008X011 Piston Assembly, high pressure (.010 oversize)
includes ring set, piston pin, retaining rings, & piston
2008X021 Piston Assembly, high pressure (.020 oversize)
includes ring set, piston pin, retaining rings, & piston
110804X Replacement Connecting Rod Assembly
includes connecting rod assembly, connecting rod inserts, & locknuts

N.S.S. = Not Sold Separate

@ Indicates torque value in foot pounds (dry threads)

QR 340 Quincy Compressor

50216-107, August 2010 12 3501 Wismann Lane, Quincy IL. - 62305-3116

CYLINDER & HEAD GROUP 115047-002
(control versions L, LS & LVD)

QR 340 Quincy Compressor

50216-107, August 2010 13 3501 Wismann Lane, Quincy IL. - 62305-3116

 HEAD ASSEMBLY 114984UU
(control versions L, LS & LVD)

QR 340 Quincy Compressor

50216-107, August 2010 14 3501 Wismann Lane, Quincy IL. - 62305-3116

SUCTION VALVE ASSEMBLY 7277X1

QR 340 Quincy Compressor

50216-107, August 2010 15 3501 Wismann Lane, Quincy IL. - 62305-3116

 DISCHARGE VALVE ASSEMBLY 7271X004

QR 340 Quincy Compressor

50216-107, August 2010 16 3501 Wismann Lane, Quincy IL. - 62305-3116

UNLOADER ASSEMBLY 40192

QR 340 Quincy Compressor

50216-107, August 2010 17 3501 Wismann Lane, Quincy IL. - 62305-3116

 PNEUMATIC UNLOADER ASSEMBLY 40055

QR 340 Quincy Compressor

50216-107, August 2010 18 3501 Wismann Lane, Quincy IL. - 62305-3116

CONTROL GROUP 110860
(control versions L)
Item Part Part
Number Qty. Number Number Description
0-200 PSI 201-500 PSI
1 1 110827-001 110827-002 hydraulic unloader assembly
2 3 1642 1642 tube fitting, 90° male elbow, 1/4 tube x 1/8 npt
3 4 ft. 110515-025 110515-025 copper tube, 1/4 o.d.
4 1 1665 1665 tube fitting, male branch tee, 1/4 tube x 1/4 tube x 1/8 npt

Maintenance Parts
113225 113225 Hydraulic Unloader Repair Kit
includes diaphragm, stem assembly, inlet filter & fitting assembly,
spring (0-200 PSI) and spring (201-500 PSI, red color code)
Parts for Special Applications
(for use with diester or phosphate ester synthetic lubricants)
1 1 110827-003 hydraulic unloader assembly (standard, 0-200 PSI)
1 1 110827-004 hydraulic unloader assembly (high pressure, 201-500 PSI)

2 4

1/4 o.d. tube

2 2 from receiver
1

QR 340 Quincy Compressor

50216-107, August 2010 19 3501 Wismann Lane, Quincy IL. - 62305-3116

 CONTROL GROUP 116112-175 & 116112-998
(control version LS)

* See page 24 for optional pilot valves that must be used with respective pressure ranges.

QR 340 Quincy Compressor

50216-107, August 2010 20 3501 Wismann Lane, Quincy IL. - 62305-3116

CONTROL GROUP 116112-999 & 116112-000
(control version LS)

* See page 24 for optional pilot valves that must be used with respective pressure ranges.

QR 340 Quincy Compressor

50216-107, August 2010 21 3501 Wismann Lane, Quincy IL. - 62305-3116

 CONTROL GROUP 116115-165 & 11615-998
(control version LVD)

* See page 24 for optional pilot valves that must be used with respective pressure ranges.
QR 340 Quincy Compressor

50216-107, August 2010 22 3501 Wismann Lane, Quincy IL. - 62305-3116

CONTROL GROUP 116115-999 & 116115-000
(control version LVD)

* See page 24 for optional pilot valves that must be used with respective pressure ranges.
QR 340 Quincy Compressor

50216-107, August 2010 23 3501 Wismann Lane, Quincy IL. - 62305-3116

 PILOT VALVES

WARNING !
Not all pilots are for use with all compressor systems. Make
sure that the pilot you order is set within the safe operating
limits of your compressor. Failure to heed this warning
could result in an explosion.

QR 340 Quincy Compressor

50216-107, August 2010 24 3501 Wismann Lane, Quincy IL. - 62305-3116

 sors in the field, not equipped with a suction valve
SUCTION VALVE unloader assembly, can be converted to constant
UNLOADER ASSEMBLIES speed. Consult your local Quincy distributor for
assistance with conversion procedures.
Description
The Quincy suction valve unloader assembly con- Service
sists of unloading arrangements on the suction valves, Periodically check the filter & screens in the inlet of
having a plunger to contact the suction valve disc the pilot valve to make sure they are free of obstruc-
and an unloader pilot valve (part no.s 113708-***, tions. If they become clogged, remove and clean or
110998-***, and 110832-*** & 111423-***) to auto- replace. Inspect the "o"ring located in the opposite
matically regulate the passing of receiver pressure end of the pilot valve body for wear or damage;
to the unloading arrangement. replace if necessary.

Application Adjustment
Suction valve unloader assemblies are recommended The unloading pressure is adjustable and is regu-
for use on Quincy compressors where the compres- lated by turning the hex nut (marked "unload adj."
sor is to run continuously and a constant pressure is in cross sectional illustrations of pilot valves). Turn
to be maintained. The purpose is to automatically the hex nut clockwise to increase and counterclock-
unseat the suction valve of the compressor when the wise to decrease the unloading pressure.
air supply is greater than the demand.
The differential (difference between unloading
Operation and loading pressure) is set by turning the hex nut
Unloading occurs when receiver pressure is suffi- (marked "differential adj." in the cross sectional
cient to overcome pilot valve spring pressure. The illustrations of the pilot valves). Increase the differ-
check ball is then unseated, allowing receiver pres- ential pressure by turning the hex nut clockwise -
sure to pass to the unloading arrangements. The decrease by turning counterclockwise. Tighten the
compressor will run unloaded until the receiver locknuts after adjustment.
pressure drops to a predetermined level. At this
time, the action of the ball is reversed, shutting off
receiver pressure to the unloader arrangement and CHECK VALVE
venting the unloader to atmosphere. This allows the
compressor to load. The drive, either electric motor ASSEMBLIES
or combustion engine, runs continuously and must
1
be started and stopped manually.

Pilot valves 111423-*** & 110998-*** can be

locked out, for models equipped with dual control, to
provide automatic start/stop operation. The knurled
knob at the top of the pilot can be turned clockwise,
until it stops, to lock it out. A pressure switch is
required to stop the motor. Failure to use a pressure
switch, with the pilot valve locked out, could result
in unsafe conditions. 2

WARNING !
A pressure switch must be incorporated whenever pilot Check Valve Assembly Replacement Parts
valve 111423-*** or 110998-*** is employed as part of the
control system. Item Part
# Qty. Number Description
6194X2 Check Valve Assembly
The compressor will operate in the continous run 1 1 123157-010 "o"ring
mode if the knurled knob is turned counterclockwise 2 1 6196-002 disc
until it stops.
6194X3 Check Valve Assembly
Installation (for use with diester or phosphate ester synthetic lubricants)
1 1 22749-010 "o"ring
The pilot valve is to be connected to the air receiver 2 1 6196-003 disc
using a minimum of 3/8" o.d. copper tube. Compres-

QR 340 Quincy Compressor

50216-107, August 2010 25 3501 Wismann Lane, Quincy IL. - 62305-3116

 HYDRAULIC UNLOADER ASSEMBLIES

Hydraulic Unloader 110827-001 & 110827-003*

*for use with diester or phosphate ester synthetic lubricants

Not all hydraulic unloader assemblies are for use with all compressor
systems. Make sure that the hydraulic unloader assembly you order
is within the operating limits of your system.

Hydraulic Unloader Assembly Repair Kit 113225

Item Part
# Qty. Number Description

1 1 diaphragm
2 1 stem assembly
(includes 2 - "o"rings)
3 1 filter assembly
(includes fitting & screens)
4 1 spring

QR 340 Quincy Compressor

50216-107, August 2010 26 3501 Wismann Lane, Quincy IL. - 62305-3116

 Head Kit K340A Basic Compressor Repair Kit 110823-340
Item Part Item Part
# Qty. Number Description # Qty. Number Description
6 1846 valve disc
3 7270 valve spring 1 110190-008 piston pin
3 7270-2 valve spring 1 110377E100 air filter element
6 1848 gasket, valve 1 110774 "o"ring kit
2 6682 valve cover gasket 1 110814 oil filter
2 1852 gasket, valve cover 1 2720 bearing cup
2 1556 gasket, valve 1 2788 bearing cone
2 1855 diaphragm 1 3720 bearing cup
1 6680 cylinder to head gasket 1 40775 bearing cone
1 110377E100 air filter element 2 6443SR connecting rod bushing
2 5702 intercooler to head gasket 2 6656PR connecting rod inserts (1 pair)
3 7270 valve spring
Overhaul Kit K340B 3 7270-2 valve spring
1 7088 gasket set
Item Part 1 6452 ring set
# Qty. Number Description 6 1846 valve disc
1 110377E100 air filter element 1 110146 piston pin
2 1855 diaphragm 1 7595 ring set
6 1846 valve disc
2 6656PR connecting rod inserts (1 pair)
3 7270 valve spring Gasket Set 7088
3 7270-2 valve spring Item Part
1 7088 gasket set # Qty. Description
Number
1 6452A ring set
1 7595A ring set 2 1315 inspection plate gasket
3 1383 bearing adj. shim, .005 steel
Piston Pin Kit K340E 5 1383A bearing adj. shim, .007 steel
3 1383B bearing adj. shim, .020 steel
Item Part
2 1383D bearing adj. shim, .002 steel
# Qty. Number Description
2 1556 gasket
1 6443SR con-rod bearing 6 1848 valve gasket
1 110190-008 piston pin 2 1852 valve cover gasket
1 110146 piston pin 1 5502 gasket
2 110799-010 needle bearing 1 5827-2 gasket, cylinder to crankcase
2 8648 retaining ring 2 5828 gasket, companion flange
2 5702 gasket, intercooler to head
1 6679 gasket, oil inlet bracket
Recommended Spare Parts 2 6682 valve cover gasket
Item Part 1 6680 gasket, cylinder to head
# Qty. Number Description
3 7277X replacement suction valve assy.
3 7271X04 replacement discharge valve
assy.
1 110822 pressure gauge
1 160079 oil pump repair kit
1 7088 gasket set
1 113225 hydraulic unloader repair kit
2 6656PR connecting rod inserts (1 pair)
2 1855 unloader diaphragm
1 110832-051 pilot repair kit 2 3
1 110377E100 air filter element

Yearly Maintenance Kit 110516-340 1

Item Part
# Qty. Number Description Decals
1 110822 oil pressure gauge Item Part
2 1855 diaphragm # Qty. Number Description
6 1857 valve pin
6 1846 valve disc 1 1 110831 serial number & nameplate
2 6283 hydraulic unloader filter 2 1 127889-A decal, CAUTION!/manual/
3 7270 valve spring "Failure to follow..."
3 7270-2 valve spring 3 1 127889-B decal, DANGER! /
6 6910 valve spring "Air used for breathing..."
1 7088 gasket set * Not sold separate; order 127889.

QR 340 Quincy Compressor

50216-107, August 2010 27 3501 Wismann Lane, Quincy IL. - 62305-3116

 TYPICAL UNIT REPAIR PARTS LIST
The parts listed here are for standard QR 340 (up to 175 PSI.) units and may or may not be applicable to custom built units. Check with
your local authorized Quincy distributor for parts that can be used for custom built units. Make sure the components you order are rated
within the safe operating limits of your system. If you are doubtful about which components to order, contact you local Quincy distributor.

(QR 340 simplex - horizontal tank - electric motor)

Part Part Part
Qty Number Number Number Description
80 gal. 120 gal.
1 113269-200 113271-200 tank (200 PSI max. working pressure)
1 113276 * 113280 top plate
1 2713 111136-050 tank drain valve
1 111136-100 111136-100 ball valve
1 110514-300 110514-300 pressure gauge
1 110512-003 110512-003 § pressure switch (135-175 PSI)
1 110513-200 110513-200 pressure relief valve (200 PSI)
3.5 ft. 110515-100 110515-100 ! discharge tube (1" copper tube to be formed by customer)
2 111265-100 111265-100 ferrule (for discharge tube)

7.5 h.p.
2 110258B082 drive belt
1 3202 motor pulley
1 111967K002 belt guard assembly
1 110484 motor pulley bushing

200v, 3Ø 230/460v, 3Ø
1 8393 124517-009 7.5 h.p. motor (ODP)

(QR 340 duplex - horizontal tank - electric motor)

Part Part Part
Qty Number Number Number Description
120 gal. 200 gal.
1 113467-200 113469-200 tank (200 PSI max. working pressure)
2 113280 113280 top plate
1 111136-050 111136-050 tank drain valve
1 111136-100 111136-100 ball valve
1 110514-300 110514-300 pressure gauge
2 110512-003 110512-003 pressure switch (135-175 PSI)
1 110513-200 110513-200 pressure relief valve (200 PSI)
7 ft. 110515-100 110515-100 ! discharge tube (1" copper tube to be formed by customer)
2 111265-100 111265-100 ferrule (for discharge tube)

7.5 h.p.
4 110258B082 drive belt
2 3202 motor pulley
2 111967K002 belt guard assembly
1 110484 motor pulley bushing

200v, 3Ø 230/460v, 3Ø
2 8393 124517-009 7.5 h.p. motor (ODP)

* 113280 top plate is also used for all QR 340 base mounted electric motor driven units.
§ 2298-175 pressure switch on base mounted units.
Part numbers shown in italics apply to tank mounted units and base mounted units.
! Pre-formed discharge tubes are available. Contact factory with model & tank size information.

QR 340 Quincy Compressor

50216-107, August 2010 28 3501 Wismann Lane, Quincy IL. - 62305-3116

 QUINCY COMPRESSOR responsible for loss or damage in transit after having received “In Good
Order” receipt from the carrier. All claims for loss or damage in transit should
STANDARD TERMS AND CONDITIONS be made to the carrier.
TITLE & LIEN RIGHTS: The equipment shall remain personal property,
LEGAL EFFECT: Except as expressly otherwise agreed to in writing by an
regardless of how affixed to any realty or structure. Until the price (including
authorized representative of Seller, the following terms and conditions shall
any notes given therefore) of the equipment has been fully paid in cash, Seller
apply to and form a part of this order and any additional and/or different terms
shall, in the event of Buyer’s default, have the right to repossess such
of Buyer’s purchase order or other form of acceptance are rejected in advance
equipment.
and shall not become a part of this order.
PATENT INFRINGMENT: If properly notified and given an opportunity
The rights of Buyer hereunder shall be neither assignable nor transferable
to do so with friendly assistance, Seller will defend Buyer and the ultimate
except with the written consent of Seller.
user of the equipment from any actual or alleged infringement of any
This order may not be canceled or altered except with the written consent published United States patent by the equipment or any part thereof furnished
of Seller and upon terms which will indemnify Seller against all loss pursuant hereto (other than parts of special design, construction, or manufac-
occasioned thereby. All additional costs incurred by Seller due to changes in ture specified by and originating with Buyer), and will pay all damages and
design or specifications, modification of this order or revision of product must costs awarded by competent court in any suit thus defended or of which it may
be paid for by Buyer. have had notice and opportunity to defend as aforesaid.
In addition to the rights and remedies conferred upon Seller by this order, STANDARD WARRANTY: Seller warrants that products of its own
Seller shall have all rights and remedies conferred at law and in equity and manufacture will be free from defects in workmanship and materials under
shall not be required to proceed with the performance of this order if Buyer normal use and service for the period specified in the product instruction
is in default in the performance of such order or of any other contract or order manual. Warranty for service parts will be Ninety (90) days from date of
with seller. factory shipment. Electric Motors, gasoline and diesel engines, electrical
TERMS OF PAYMENT: Unless otherwise specified in the order acknowl- apparatus and all other accessories, components and parts not manufactured
edgment, the terms of payment shall be 1% 15, net forty-five (45) days after by Seller are warranted only to the extent of the original manufacturer’s
shipment. These terms shall apply to partial as well as complete shipments. warranty.
If any proceeding be initiated by or against Buyer under any bankruptcy or Notice of the alleged defect must be given to the Seller, in writing with all
insolvency law, or in the judgment of Seller the financial condition of Buyer, identifying details including serial number, type of equipment and date of
at the time the equipment is ready for shipment, does not justify the terms of purchase within thirty (30) days of the discovery of the same during the
payment specified, Seller reserves the right to require full payment in cash warranty period.
prior to making shipment. If such payment is not received within fifteen (15)
Seller’s sole obligation on this warranty shall be, at its option, to repair or
days after notification of readiness for shipment, Seller may cancel the order
replace or refund the purchase price of any product or part thereof which
as to any unshipped item and require payment of its reasonable cancellation
proves to be defective. If requested by Seller, such product or part thereof
charges.
must be promptly returned to seller, freight prepaid, for inspection.
If Buyer delays shipment, payments based on date of shipment shall
Seller warrants repaired or replaced parts of its own manufacture against
become due as of the date when ready for shipment. If Buyer delays
defects in materials and workmanship under normal use and service for ninety
completion of manufacture, Seller may elect to require payment according to
(90) days or for the remainder of the warranty on the product being repaired.
percentage of completion. Equipment held for Buyer shall be at Buyer’s risk
and storage charges may be applied at the discretion of Seller. This warranty shall not apply and Seller shall not be responsible or liable
for:
Accounts past due shall bare interest at the highest rate lawful to contract
for but if there is no limit set by law, such interest shall be eighteen percent (a)Consequential, collateral or special losses or damages;
(18%). Buyer shall pay all cost and expenses, including reasonable attorney’s (b)Equipment conditions caused by fair wear and tear, abnormal condi-
fees, incurred in collecting the same, and no claim, except claims within tions of use, accident, neglect or misuse of equipment, improper storage or
Seller’s warranty of material or workmanship, as stated below, will be damage resulting during shipping;
recognized unless delivered in writing to Seller within thirty (30) days after (c)Deviation from operating instructions, specifications or other special
date of shipment. terms of sale;
TAXES: All prices exclude present and future sales, use, occupation, (d)Labor charges, loss or damage resulting from improper operation,
license, excise, and other taxes in respect of manufacture, sales or delivery, maintenance or repairs made by person(s) other than Seller or Seller’s
all of which shall be paid by Buyer unless included in the purchase price at authorized service station.
the proper rate or a proper exemption certificate is furnished. In no event shall Seller be liable for any claims whether arising from breach
ACCEPTANCE: All offers to purchase, quotations and contracts of sales of contract or warranty or claims of negligence or negligent manufacture in
are subject to final acceptance by an authorized representative at Seller’s excess of the purchase price.
plant. THIS WARRANTY IS THE SOLE WARRANTY OF SELLERS AND
DELIVERY: Except as otherwise specified in this quotation, delivery will ANY OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED IN
be F. O. B. point of shipment. In the absence of exact shipping instruction, LAW OR IMPLIED IN FACT, INCLUDING ANY WARRANTIES OF
Seller will use its discretion regarding best means of insured shipment. No MERCHANTABILITY AND FITNESS FOR PARTICULAR USE ARE
liability will be accepted by Seller for so doing. All transportation charges are HEREBY SPECIFICALLY EXCLUDED.
at Buyer’s expense. Time of delivery is an estimate only and is based upon LIABILITY LIMITATIONS: Under no circumstances shall the Seller have
the receipt of all information and necessary approvals. The shipping schedule any liability for liquidated damages or for collateral, consequential or special
shall not be construed to limit seller in making commitments for materials or damages or for loss of profits, or for actual losses or for loss of production or
in fabricating articles under this order in accordance with Seller’s normal and progress of construction, whether resulting from delays in delivery or perfor-
reasonable production schedules. mance, breach of warranty, negligent manufacture or otherwise.
Seller shall in no event be liable for delays caused by fires, acts of God, ENVIROMENTAL AND OSHA REQUIREMENTS: At the time of ship-
strikes, labor difficulties, acts of governmental or military authorities, delays ment of the equipment from the factory, Quincy Compressor / Ortman Fluid
in transportation or procuring materials, or causes of any kind beyond Seller’s Power will comply with the various Federal, State and local laws and
control. No provision for liquidated damages for any cause shall apply under regulations concerning occupational health and safety and pollution. How-
this order. Buyer shall accept delivery within thirty (30) days after receipt of ever, in the installation and operation of the equipment and other matters over
notification of readiness for shipment. Claims for shortages will be deemed which the seller has no control, the Seller assumes no responsibility for
to have been waived if not made in writing with ten (10) days after the receipt compliance with those laws and regulations, whether by the way of indem-
of the material in respect of which any such shortage is claimed. Seller is not nity, warranty or otherwise.
QR 340 June 30, 2003 Quincy Compressor

50216-107, August 2010 29 3501 Wismann Lane, Quincy IL. - 62305-3116

Reciprocating / Systems:
Reciprocating 217.222.7700
Air Master 217.277.0270
E-mail: [email protected]
Website: quincycompressor.com