Scribd
Upload
130 views11 pages

Radar Manual

This document provides instructions for installing and using a microwave radar blind spot detection system. It includes: 1) A list of included parts and installation tools. 2) Specifications for the system's operation, including detection range and speed accuracy. 3) Diagrams showing how to connect wires and position sensors on the vehicle. 4) Instructions for installing sensors, indicators and the buzzer, and setting detection angles. 5) Explanations of alarm conditions and troubleshooting common issues.

Uploaded by

Saul Berenson
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
130 views11 pages

Radar Manual

This document provides instructions for installing and using a microwave radar blind spot detection system. It includes: 1) A list of included parts and installation tools. 2) Specifications for the system's operation, including detection range and speed accuracy. 3) Diagrams showing how to connect wires and position sensors on the vehicle. 4) Instructions for installing sensors, indicators and the buzzer, and setting detection angles. 5) Explanations of alarm conditions and troubleshooting common issues.

Uploaded by

Saul Berenson
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

MICROWAVE RADAR BLIND

SPOT DETECTION SYSTEM


User Manual

Tel:+86 0755-27986710
Email: [email protected]
Website : www.topvisiontech.en.alibaba.com
Address : 4/F Building A1 , Hedian Industrial Park , He Dian Road,
Guanlan Town,Longhua new District ,Shenzhen ,China
Catalog

I. Items List................................................................................................................................................1

II. Technical Specification....................................................................................................................... 2

III. Installation Diagram........................................................................................................................... 3

IV. Wires Connection Diagram............................................................................................................... 4

V. Installation Gist................................................................................................................................... 5

VI. Alarm Conditions................................................................................................................................ 4

VII. How to Alarm..................................................................................................................................... 5

VIII. Malfuntion Solution........................................................................................................................ 6


Thanks for using our Microwave BSD system. For your convenience, please read the User Manual
carefully and follow the instructions in the manual.
I. Items list

Number Item Name Quantity Picture

1 Main Unit 1PCS

2 Main Harness 1PCS

3 Sensor 2PCS

4 LED Indicator 2PCS

5 GPS 1PCS

6 Buzzer 1PCS

7 3M tape 4PCS

Tools for instalation: angle gauge; insulated tape; multi-meter;s crewdriver; cleaning cloth; tape
II.Technical specification

Operating frequency 24.0 ----24.25GHZ

Transmit power 15dbm

Detection range 40 degree


Detection ability 5 targets can be detected at the same time

Speed range 0.55km/h---220km/h

Speed accuracy < 0.55km/h

Direction of movement approached or overtaken by vehicles

Truck : 0.3m-15m
Detection range Car : 0.3m-15m
Motorcycle:0.3m-10m
Pedestrian:0.3m-7m
Operating voltage 9---24V(9---35V as customized

Working current < 200mA


Working temperature -40℃ ~ + 85℃

III.Installation Diagram
IV. Wires Connection Diagram

L_lamp can+/- ACC

GND
GPS R_lamp

L_sensor

L_LED indicator

R_sensor

R_LED indicator

Buzzer
V. Installation Gist
1.Sensor settings
Installation requirements: Sensor of the BSD system should be pasted to both side inner corner of
rear bumper shell with angle of 25 to 30 degrees and the height range is 35-90cm.(Fig.1-Fig.2)

The plane angle between


the rear bumper and the
sensor is 30 degree.

Fig.1 Fig.2

Step1: Measure method: Get close to the rear bumper shell with the angle gauge, and one end
should be paralleled with the rear bumper, the other end is positioned at an angle of 30
degree.(Fig.3-Fig.4)

Fig.3 Fig.4

Step2: Mark down the position in the bumper with a marker and Mark down the position with
same method for the other side of bumper.(Fig.5-Fig.6)
Step3: Take off the rear plastic bumper, and clean the installation of position with cloth.(FIg.7)

Clean the installation of


position with cloth.

Fig7

Step4: Place a 3M adherent tape on the sensor, and place the other 3M adherent tape pasting in
the determined postion; and then stick the sensor to the positon.

Step5: Similarly, the L_ sensor is also installed using the same method. (Fig.8- Fig.9)
Fig.8 Fig.9

2. Installation of the left/right signal light Harness

Step6. Take off the tail light, turn on the LH turn signal switch, then LH turn indicator is on, find
out the 12V power cable with multi-meter, connect the R_LAMP in harness cable with the 12V
power cable, and connect the L_LAMP in harness cable with the left side power cable.
(Fig.10-Fig.12)

Fig10 Fig11 Fig12

3.LED indicator installation position:

Step7. LED indicator installed in the car inside of the left and right corner (Fig.13 – Fig.14)

Fig.13 Fig.14
4. Installation of buzzer:
Step8. Buzzer is pasted in the plastic internal of the vehicle (to ensure that there is sound output)
(Fig.19)

Fig.15

Step9. Run the wires based on the installation diagram.

VI. Alarm conditions:


1. When the system is on, the system would start detecting objects in the blind area behind the
vehicle 15 meters.(Fig.15)
2. )When the moving objects is getting closer and the speed is faster than our own cars.

Fig.16
VII. How to alarm?
A: Blind detection on right side:
1.R-LED indicator will turn on with dim/low lux effect when there is object approaching on the
right blind area.
2. If the right turn/signal switch is turned on at this time, the R-LED indicator will be flashing with
bright/high lux effect and the buzzer will be on with BiBi sound.

B: Blind detection on left side:


1.L-LED indicator will turn on with dim/low lux effect when there is object approaching on the
right blind area.
2. If the right turn/signal switch is turned on at this time, the L-LED indicator will be flashing with
bright/high lux effect and the buzzer will be on with BiBi sound.

C: The LED and buzzer without any warning if there is no object approaching on blind area.

VIII. Malfunction Solution:

NO. Malfunction Reason Solution

1 LED light doesn`t Wrong connection or missed Check the harness and make
work connection on harness sure connection is correct

LED light is broken Replace LED light

2 Contrary alarm on Contrary connection of BSD_L Exchange the connection of


right/left LED light and BSD_R on the BSD main BSD_L and BSD_R
harness

3 Buzzer doesn`t work Wrong connection or missed Check the harness and make
connection on harness sure connection is correct

Buzzer is broken Replace buzzer

You might also like