_400_Pmp_Ctrl_Eng_Main_FS_212 - Ladder Diagram Page 1

PD3H422_MG10N85:Turbomachinery_Task:Lube_B008_261 6/16/2019 2:08:58 PM

Total number of rungs in routine: 14 C:\Documents and Settings\Administrator\Desktop\DCS BACKUP\Allen Bradley\Module 70 - GTG\GTG-A\PLC\PD3H422_MG10N85.ACD

0 NOP

M6020 M6020
<UF0080:0:O.Data.4> <UF0080:0:O.Data.4> TON
1 / Timer On Delay EN
Timer Lube_Module_Fail_TON
M6020_FB M6020_FB
Preset 1000 DN
<UF0090:I.Data[0].12> <UF0090:I.Data[0].12>
Accum 0
/

FL_Lube_Module_Fail
Lube_Module_Fail_TON.DN <HMI_FSLO[3].4> PGM_Lube.Activate_Backup_System
L

Pre_Post_Pump_Run Pump_Lag_Delay_Pre_Post_TOF.DN LES

2 / Less Than (A<B)
Source A Lube_Oil_Header_Press.Val
0.048076924
Source B KF_Lube_Oil_Pre_Post_Pump_Check_Limit.Val
8.0

PS6010
Lube_Mode.Engine_Turning_Post_Lube <UF0080:I.Data[1].0> TON
/ Timer On Delay
Timer Pre_Post_Pump_Fa
PGM_Sequence.Test_Crank Preset
Accum

RSLogix 5000
_400_Pmp_Ctrl_Eng_Main_FS_212 - Ladder Diagram Page 2
PD3H422_MG10N85:Turbomachinery_Task:Lube_B008_261 6/16/2019 2:09:01 PM
Total number of rungs in routine: 14 C:\Documents and Settings\Administrator\Desktop\DCS BACKUP\Allen Bradley\Module 70 - GTG\GTG-A\PLC\PD3H422_MG10N85.ACD

FN_M6010_Fail
<HMI_FSNL[1].19> PGM_Lube.AuxPumpLoss
L

Pre_Post_Pump_Fail_TON.DN
EN
Pre_Post_Pump_Fail_TON
1000 DN
0

FN_M6020_Fail
Backup_Pump_Run Pump_Lag_Delay_Backup_TOF.DN LES <HMI_FSNL[1].20>
3 / Less Than (A<B) L
Source A Lube_Oil_Header_Press.Val
0.048076924
Source B KF_Backup_Pump_Min_Check.Val
8.0

Lube_Oil_Required LES Pre_Post_Pump_Required

4 Less Than (A<B)
Source A Lube_Oil_Header_Press.Val
0.048076924
Source B KF_Pre_Post_Pump_On_Limit.Val
25.0

Pre_Post_Pump_Required PGM_Start.Starter_Dropout_Speed
/

Pre_Post_Pump_Required PGM_Sequence.Start_Run
/
FL_PT6060_Fail
<HMI_FSLO[3].7>

RSLogix 5000
_400_Pmp_Ctrl_Eng_Main_FS_212 - Ladder Diagram Page 3
PD3H422_MG10N85:Turbomachinery_Task:Lube_B008_261 6/16/2019 2:09:01 PM
Total number of rungs in routine: 14 C:\Documents and Settings\Administrator\Desktop\DCS BACKUP\Allen Bradley\Module 70 - GTG\GTG-A\PLC\PD3H422_MG10N85.ACD

FN_M6010_Fail
Lube_Mode.Pump_Check Backup_Pump_Press_Decay_Passed_PP_On <HMI_FSNL[1].19> Pre_Post_Pump_Run
5 /
FN_M6020_Fail
Pre_Post_Pump_Required
<HMI_FSNL[1].20>

ST_Pre_Post_Lube_Pump_Command
<HMI_STATUS[4].20>

PS6010 ST_Pre_Post_Lube_Pump_Press
<UF0080:I.Data[1].0> <HMI_STATUS[4].21>
6

Lube_Mode.Pump_Check Lube_Press_Decay_Passed_BU_On Backup_Pump_Check_Passed_BU_Off

7 /

Lube_Mode.Engine_Turning_Post_Lube Backup_Pump_On_Due_To_Lo_Press_AL

Backup_Pump_Test

Restart_BU_Pump_Check

Pre_Post_Pump_Required Post_Lube_BU_Cycle_Off_TON.TT Pump_Lag_Delay_Backup_TOF.DN Backup_Pump_Run

/
FN_M6010_Fail
<HMI_FSNL[1].19>

PS6010 AL_PT6060_L
<UF0080:I.Data[1].0> Pre_Post_Pump_Run <HMI_ALARM[7].9>
/

ST_Backup_Lube_Pump_Command
Backup_Pump_Run <HMI_STATUS[4].8> PGM_Lube.Backup_Lube_Oil_Pump_On

RSLogix 5000
_400_Pmp_Ctrl_Eng_Main_FS_212 - Ladder Diagram Page 4
PD3H422_MG10N85:Turbomachinery_Task:Lube_B008_261 6/16/2019 2:09:01 PM
Total number of rungs in routine: 14 C:\Documents and Settings\Administrator\Desktop\DCS BACKUP\Allen Bradley\Module 70 - GTG\GTG-A\PLC\PD3H422_MG10N85.ACD

PS6020 ST_Backup_Lube_Pump_Press
<UF0080:I.Data[1].2> <HMI_STATUS[4].9>
8

MUL MUL
9 Multiply Multiply
Source A KF_Pump_Lag_Delay_Pre_Post.Val Source A KF_Pump_Lag_Delay_Backup.Val
60.0 30.0
Source B 1000 Source B 1000

Dest Pump_Lag_Delay_Pre_Post_TOF.PRE Dest Pump_Lag_Delay_Backup_TOF.PRE

60000 30000

Pre_Post_Pump_Run Pre_Post_Pump_On_ONS TOF

10 ONS Timer Off Delay EN
Timer Pump_Lag_Delay_Pre_Post_TOF
Pre_Post_Pump_Run Pre_Post_Pump_Off_ONS Preset 60000 DN
/ ONS Accum 60009

Backup_Pump_Run Backup_Pump_On_ONS TOF

11 ONS Timer Off Delay EN
Timer Pump_Lag_Delay_Backup_TOF
Backup_Pump_Run Backup_Pump_Off_ONS Preset 30000 DN
/ ONS Accum 30015

M6020
Backup_Pump_Run <UF0080:0:O.Data.4>
12 /

M6010
Pre_Post_Pump_Run <UF0090:O.Data[1].6>
13 /

(End)

RSLogix 5000