Horizontal Centrifugal Pump - According To Iso 2858: Chemical Pumps Via Labirinto 159 - 25125 BRESCIA - ITALY
Horizontal Centrifugal Pump - According To Iso 2858: Chemical Pumps Via Labirinto 159 - 25125 BRESCIA - ITALY
Horizontal Centrifugal Pump - According To Iso 2858: Chemical Pumps Via Labirinto 159 - 25125 BRESCIA - ITALY
This manual contains rules and suggestions for making the most out of the pump you have purchased in total safety.
IDENTIFICATION CODE
pump data motor data
32/125 closed impeller: SE1 single
32/160 De mm SE2
40/125 SE3
40/160 WR (polypropylene PP) other types: B1
40/200 ER (polyethylene PE) open: TS2 N2 1450
50/125 QR (polyvinyl chloride PVC) De_ X V (FPM) M2 double N3 2900
50/160 WF (casing in PP; impeller in PVDF) recessed: E (EPDM) M3 N4 1740 2P 50 Hz s.f.
ZGE 50/200 FC (polyvinylidene fluoride PVDF) De_Y F (FEP) M4 N5 3480 4P kW 60 Hz Volt 3 f.
item/plant:
service:
legend
Ref. Pos. Part name Q.ty Disassembling steps sequence Spare stock per
working years
No 1 2 3 4 5 6 7 8 9 10 2 5
102 45 VOLUTE CASING 1
135 42 INTERMEDIATE PLATE 1 1 1
152 5 DISCHARGE SECTION 1
153 53 SUCTION SECTION 1
155 2 FRONT FLANGE 1
183 35 SUPPORT FOOT 1
184 6 REAR FLANGE 1
210 30 PUMP SHAFT 1 1
230 46 CENTRIFUGAL IMPELLER 1 1 1
260 51 OGIVE 1 1 1
320 34 BEARING (motor side) 1 1
322 13 BEARING (pump side) 1 1
330 36 SUPPORT 1
360,1 11 BEARING COVER (pump side) 1
360,2 33 BEARING COVER (motor side) 1
412,1 54 O ring (suction section) 1 1 1
412,2 3 O ring (discharge section) 1 1 1
412,3 4 O ring (volute casing) 1 1 1
412,4 47 O ring (drain plug) 1 1 1
414,1 49 O ring (ogive) 1 1 1
414,2 1 O ring (impeller) 1 1 1
421,1 39 ELASTIC SEAL RING 1 1
421,2 17 ELASTIC SEAL RING 1 1
430 10 MECHANICAL SEAL (1) 1 1 1
471 9 SEAL CHAMBER 1 1 1
524 40 SHAFT SLEEVE 1 1 1
551 16 SPACE RING 1
552 50 WASHER 1 1
638 38 CAP (oil drain) 1
643 14 BULB LUBRICATOR 1
800 24 ELECTRIC MOTOR 1
861,1 21 SEMI-COUPLING (motor side) 1
861,2 31 SEMI-COUPLING (pump side) 1
862 20 SPACER 1
865 27 COUPLING GUARD 1
890 25 BASE 1
901,1 12 SCREWS (bearing cover) 4
901,2 15 SCREWS (bearing cover) 4
901,3 19 SCREW (coupling) 6
904,1 18 GRUB SCREW (coupling) 1
904,2 22 GRUB SCREW (coupling) 1
910 7 CASING SCREWS 6
912 48 DRAIN PLUG 1
914,2 41 SCREWS (flange/support) 4
914,3 8 SCREWS (seal chamber) 4
914,4 44 SCREWS (intermediate plate fixing) 4
920,1 43 SCREWS (pump locking) 4
920,2 37 SCREWS (support locking) 2
920,3 29 SCREWS (coupling guard locking) 4
920,4 26 SCREWS (motor locking) 4
922 52 NUT (impeller locking) 1 1
932 32 SEEGER RING 1 1
940,1 55 FEATHER KEY 1 1
940,2 28 FEATHER KEY 1
940,3 23 FEATHER KEY 1
(1) Ref. 430: see specific instructions pump rotor
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
414 155 412 412 152 184 910 914 471 430 360 901 322 643 901 551 421 904 901 862 861 904 940 800
.2 .2 .3 .3 .1 .1 .2 .2 .1 .3 .1 .2 .3
55
940.1
54
412.1
53
153
52
922
51
260
50
552
49
414.1
48
912
47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25
412 230 102 914 920 135 914 524 421 638 920 330 183 320 360 932 861 210 920 940 865 920 890
.4 .4 .1 .1 .2 .2 .2 .3 .2 .4
GENERAL HINTS
HYDRAULICALLY alike to all centrifugal pumps, it is equipped with a blade-type impeller rotating within a fixed
housing. It has a radial outlet (facing the upper part of the pump, with an internal deflector) and, by creating a
depression in the center, it allows the liquid to flow from the central suction side. Then, flowing through the
impeller's blades the fluid acquires energy and is conveyed towards the outlet.
MECHANICALLY, the static stress caused by the piping is borne by the metal shields (front and rear flanges) on
the pump body. Directly the pump shaft causes the impeller to rotate and is driven by rolling bearings that transfer
all the mechanical impeller loads onto the support. The pump is connected to the electric motor (IEC, B3 frame, to
be fixed onto a common base) by means of a flexible coupling and spacer. A guard (non-hermetically sealed)
prevents unauthorised access. The spacer allows worn components (pump rotor) to be removed without having to
disconnet the piping and remove the motor.
rotating mechanical seal bearings support
pump shaft
pump rotor
impeller
flexible coupling
OUTLET
motor
pump casing
coupling
guard
INLET
spacer
base
THE MECHANICAL SEAL, placed at the point where the shaft enters the pump body to drive the impeller, is made
up of two main sections: a fixed section inserted in the pump body and a rotating section integral with the shaft.
The tight contact between these two parts guarantees a seal against leakage whether the pump is rotating or not.
The rubbing action that occurs between these two parts when the pump is operating generates heat by friction;
this heat is absorbed by the liquid being pumped in the case of single mechanical seal and by the cooling liquid
(generally water) in the case of double seal. The presence of the thin layer of liquid between the sealing
surfaces, as well as its cooling action, is indispensable for the life of the seal.
MOTOR
R S T
U V W
X Y Z
DIRECTIONS FOR USE
TRANSPORT INSTRUCTIONS
- cover the hydraulic connections
- when lifting the unit do not exert force on the plastic fittings
- lay the pump on its base or fixing plate during transport
- if the road is particularly rough, protect the pump by means of adequate shock absorbing supports
- bumps and shocks may damage important working parts vital for safety and functionality of the machine
INSTALLATION INSTRUCTIONS
- clean the plant before connecting the pump ←!
- make sure that no foreign bodies are left in the pump. Remove safety caps on the hydraulic connections.
- follow the instructions indicated in the following diagram:
4 10
1 2 3
11
≅ (8xDN) mm
+y 0,00
12
13
23 22 21 20 19 18 17 16 15 14
- anchor the pump to an adequate base plate having a mass at least 5 times that of the pump
- do not use anti-vibration mounts to fix the pump
- anti-vibration joints are recommended on the pipe connections; mandatory over DN 100
- we suggest to use the by-pass piping when pumping at reduced capacity
- with viscous liquids reduce the fluid speed in the pipes
- manually verify that all rotating parts are free to turn without abnormal friction by turning the motor cooling fan
- make sure that the power supply is compatible with the data shown on the pump motor identification plate
- connect the motor to the power supply via a magnetic/thermal control switch
- ensure that star-delta starting is implemented for motors whose power is more than 15kW
- install emergency stop devices to switch off the pump in case of low liquid level (floating, magnetic, electronic, pressure-
sensitive)
- ambient temperature as a function of the physical-chemical characteristics of the liquid to be pumped and in any case
not greater or lower than the interval indicated in the GENERAL NOTES
- other environmental conditions in accordance with the IP protection of the motor
- install a drainage pit to collect any liquid overflow from the base drainage channel due to normal maintenance work
- leave enough free space around the pump for a person to move
- leave free space above the pump for lifting operations
- highlight the presence of aggressive liquids with coloured tags following the local safety regulations
- do not install the pump (made in thermoplastic material) in close proximity to heating apparatus
- do not install the pump in areas subject to solid or liquid matter falling
- do not install the pump in an explosive atmosphere unless the motor and its coupling have been adequately pre-
arranged
- do not install the pump in close proximity to workplaces or crowded areas
- install extra protection guards for the pump or persons as the need arises
- install a spare equivalent pump in parallel
STARTUP
- verify that the instructions outlined in the INSTALLATION have been followed ←!
- verify the correct direction of rotation (clockwise from the motor side) supplying the motor with short impulses
- ensure that the NPSH available is greater than that required by the pump (in particular for hot liquids, liquids with high
vapour pressure, very long suction pipes)
- close the drain valve (pos. 17); totally flood the suction pipe and the pump
- start the pump with the suction valve completely open and the discharge valve partially closed
- slowly regulate the flow by opening or closing the discharge valve (never the suction valve). Make sure that the power
absorbed by the motor does not exceed the rated one indicated on the motor identification plate
- do not operate the pump at the limit values of its performance curve: maximum head (discharge valve excessively
closed) or maximum capacity (total absence of drops and geodetic head on the discharge side)
- set the operating point to that for which the pump was requested
- ensure that there are no abnormal vibrations or noise due to inadequate mounting or cavitation
- avoid short and/or frequent starts by properly setting the control devices
Motor Power ; kW 0,75÷5,5 7,5÷30 37÷110 132÷200 250÷315
Max. starts per hour ; 2 - 4 poles 20 - 40 10 - 20 6 - 12 2-4 1-2
- ensure that the temperature, pressure and liquid characteristics are as those specified at the time of order.
OPERATING INSTRUCTIONS
- switch automatic control on
- do not activate valves whilst the pump is in operation
- risks of dangerous water hammer effects in case of sudden or improper valve actuation (only trained personnel should
operate valves)
- completely empty and wash the pump before using a different liquid
- isolate or empty the pump if the crystallization temperature of the liquid is the same or lower than the ambient
temperature
- stop the pump if the liquid temperature exceeds the maximum allowed temperature indicated in the GENERAL NOTES;
if the increase is of approximately 20%, check internal parts
- close the valves in case of leaks
- wash with water only if compatible from the chemical point of view. As alternative use an appropriate solvent that will not
generate dangerous exothermal reactions
- contact the liquid supplier for information on the appropriate fire precautions
- empty the pump in case of long periods of inactivity (in particular with liquids which would easily crystallize)
DISASSEMBLY
- all these maintenance operations must be performed under supervision of qualified personnel
- cut off the power supply from the motor and disconnect the electrical wiring; pull the wires out from the terminal box and
isolate their extremities accordingly
- close the suction and discharge valves and open the drain valve
- use gloves, safety glasses and acid-proof overalls when disconnecting and washing the pump
- disconnect the piping and leave enough time for the residual liquid to exit the pump body and atmospheric air to fill the
empty volume
- wash the pump before carrying out any maintenance work
- do not scatter the liquid in the environment
- before attempting to dismantle the pump ensure that its motor is disconnected and that it may not be started
accidentallly
- now open the pump following the sequence indicated in the respective table of the LEGEND
- for the disassembly of the rotating parts follow the suggestions outlined in the RECOMMENDATIONS section
MAINTENANCE
- all these maintenance operations must be performed under the supervision of qualified personnel
- make periodic inspections (2 to 30 days depending on the type of liquid and the operating conditions) clening filtering
sections
- make periodic inspections (1 to 6 months depending on the type of liquid and the operating conditions) on the rotating
parts of the pump (pump rotor); clean or replace or lubricate as necessary (see RECOMMENDATIONS)
- make periodic inspections (3 to 5 months depending on the type of liquid and the operating conditions) on the
functionality of the motor control system; efficiency must be guaranteed
- the presence of liquid below the pump could be a clue to pump problems
- excessive current consumption could be an indication of impeller problems
- unusual vibrations could be due to unbalanced impeller (due to damage or presence of foreign material obstructing its
blades)
- reduced pump performance could be due to an obstruction of the impeller or damages to the motor
- motor damages could be due to abnormal friction within the pump
- damaged parts must be replaced with new original parts
- the replacement of damaged parts must be carried out in a clean dry area
SAFETY RISKS ←!
Safety risks for personnel mainly arise from improper use or accidental damages.
These risks may be of an electrical nature as far as the non-synchronous motor is concerned and may cause injury to
hands if working on an open pump. Risks may also arise due to the nature of the liquids pumped. It is therefore of
utmost importance to closely follow all the instructions contained in this manual so as to eliminate the causes that
may lead to pump failure and the consequent leakage of liquid dangerous for both personnel and the environment.
Risks may also arise from improper maintenance or dismantling practices.
In any case five general rules are important:
A - all services must be carried out by specialised personnel or supervised by qualified personnel depending on the
type of maintenance required
B - install protection guards against eventual liquid sprays (when the pump is not installed in remote areas) due to an
accidental pipe rupture. Arrange for safety basins to collect possible leakage
C - when working on the pump always wear acid-proof protective clothing
D - arrange for proper conditions for suction and discharge valve closing during disassembly
E - make sure that the motor is completely disconnected during disassembly.
Proper design and building of the plants, with well positioned and well marked piping fitted with shut-off valves, adequate
passages and work areas for maintenance and inspections are extremely important (should the plant be faulty
constructed or present wear-and-tear defects, the pressure developed by the pump could lead to failure).
It must be stressed that the major cause of pump failures leading to a consequent need to intervene is due to the pump
running dry in manually operated plants. This is generally due to:
- the suction valve being open at start-up or
- the suction tank being emptied without stopping
Interventions allowed only to specialised personnel who may eventually delegate to others some operations depending on
specific evaluations (technical capability required: specialisation in industrial plumbing or electric systems as
needed).
Interventions allowed to general operators (after training on the correct use of the plant):
- pump starting and stopping
- opening and closing of valves with the pump at rest
- emptying and washing of the pump body via special valves and piping
- cleaning of filtering elements
Interventions allowed to qualified personnel (technical capacities required: general knowledge of the mechanical,
electrical and chemical features of the plant being fed by the pump and of the pump itself):
- verification of environmental conditions
- verification of the condition of the liquid being pumped
- inspections of the control/stop devices of the pump
- inspections of the rotating parts of the pump
- trouble shooting
PERSONNEL RESPONSIBLE FOR REPAIRS
Interventions by qualified personnel (technical capacities required: general knowledge of machining operations,
awareness of possible damage to parts due to abrasion or shocks during handling, know-how of required bolt and
screw tightening required on different materials such as plastics and metals, use of precision measuring
instruments):
- opening and closing of the pump body
- removal and replacement of rotating parts
WASTE DISPOSAL
Disassembly:
All threads are right handed
The impeller, once the pump rotor is disconnected, must be removed by blocking the opposite end of the shaft (removing
the half coupling if necessary); unscrew the protection cap (ogive) and locking nut (right hand thread), then remove the
impeller axially.
Follow the specific attached instructions when working on the mechanical seal.
Remove the shaft from its support (with the bearing on the motor side) by sliding it in direction of the coupling side; the
bearing on the pump side must be in position before refitting the shaft (see Table 5: bearings and oil seal rings).
Replace the parts that was: broken, cracky, smelt.
Clean all surfaces before reassembly; in particular seal rings (risk of leakage or premature wear), O-RING seats (risk of
leakage). bearings rings and seats of the support.
Shaft run-out on the impeller side must not exceed 30 µm.
Check alignment and end play among the flexible components of the coupling after reassembling:
Max. radial deviation <0,5 mm; max. angular displacement <1°; end play: 2÷4 mm
Screw fastening torque M4 M6 M8 M10 M12 M16 M20 M24
to be reduced by 25 % clamping plastic components Nm 4 14 24 48 60 75 120 175
greasing:
The pump is supplied without oil (bearing housing is empty); fill with lubricating oil as per ISO 6743.
kinematics viscosity : ref. to 50 °C (125°F): 2,8÷3,3 °E (≅ 20 cSt)
operating conditions: temperature increment 40 °C; max. temperature 100 °C; max. rpm 4000.
Add oil in the bulb lubricator (100 cc) approximately every 300 hours of working.
Completely drain and replace oil after 2000 operating hours (from 600 cc to 1200 cc, according to the pump size).
Improper use:
The pump must not be used for purposes other than the transfer of liquids.
The pump cannot be used to generate isostatic or counter pressures.
The pump cannot be used to mix liquids generating an exothermal reaction
The pump must be installed horizontally on a firm base.
The pump must be installed on a suitable hydraulic plant with inlet and outlet connections to proper suction and discharge
pipes.
The plant must be able to shut off the liquid flow independently from the pump.
Handling of aggressive liquids requires specific technical knowledge
tolerance of tech. data: dimensions =± 7 %; weights and gravity-centre =± 14 %; performance: according to ISO 2548
The pump does not deliver: 19- the specific weight of the liquid is greater than
01- wrong sense of rotation expected
02- suction piping is too long or has too many bends 20- impurities inside the pump generate abnormal
03- not enough suction head on the pump friction
04- air intake from suction and secondary piping 21- the power supply voltage is not the one on the motor
05- pump or suction piping not completely flooded identification plate
06- impeller blades obstructed by impurities
07- non-return valve on the discharge pipe blocked
08- the geodetic head of the plant is greater than the The pump vibrates and is noisy
maximum head developed by the pump see 20
09- impeller blocked by a considerable layer of crystals 22- the pump is working at free capacity (zero head)
or by melting due to dry running 23- the pump or piping are not firmly fixed
24- damaged or dry central support bearings
25- wrong alignment of the flexible coupling
The pump has reduced capacity or insufficient pressure:
see 01, 02, 03, 04, 05, 06 The pump shows signs of premature wear of internal
10- the head required by the plant is greater than that parts:
expected see 20
11- insufficient nominal diameter of suction piping, shut- 26- liquid is excessively abrasive
off valve or other suction parts 27- frequent recurrence of cavitation (see 02, 11, 15, 17)
12- insufficient geodetic suction head on the pump 28- high tendency of the liquid to crystallize or
13- damaged or worn impeller polymerize in stand-by
14- viscosity of liquid greater than that expected 29- pump execution with materials not suitable for the
15- excessive quantities of air or gases in the liquid liquid being pumped
16- bends, non-return valve or other parts close to the 30- operation at much reduced capacity
outlet
17- liquid (especially if hot) liable to change to gaseous
state The seal leaks drops of liquid:
The pump is overloaded: 31- scratched or incorrectly installed seal rings
see 14 32- high run-out of pump shaft
18- capacity is higher delivery than expected
TAB. 1
M. 3f B3 ZGE: 32/125; 40/125 M. 3f B3 ZGE: 32/160; 40/160 M. 3f B3 ZGE: 50/125
2900 rpm 2900 rpm 2900 rpm
type kW A B C D H base type kW A B C D H base type kW A B C D H base
80 1,1 845 360 332 150 192 N2 100L 3 935 390 372 170 212 N3 112M 4 975 390 372 190 212 N3
90S 1,5 895 360 332 150 192 N2 112M 4 955 390 372 170 212 N3 132S 5,5 1055 450 392 210 232 N4
90L 2,2 920 390 332 170 192 N3 132S 5,5 1035 450 392 190 232 N4 132S 7,5 1055 450 392 210 232 N4
100L 3 935 390 332 170 192 N3 132S 7,5 1035 450 392 190 232 N4 160M 11 1185 490 420 230 260 N5
112M 4 955 390 332 170 192 N3 160M 11 1165 490 420 210 260 N5 160M 15 1185 490 420 230 260 N5
132S 5,5 1035 450 372 190 232 N4 160M 15 1165 490 420 210 260 N5
63 0,18 820 360 332 150 192 N2 71 0,37 820 360 372 150 212 N2 80 0,55 865 360 372 170 212 N2
71 0,25 820 360 332 150 192 N2 80 0,55 845 360 372 150 212 N2 80 0,75 865 360 372 170 212 N2
71 0,37 820 360 332 150 192 N2 80 0,75 845 360 372 150 212 N2 90S 1,1 915 360 372 170 212 N2
80 0,55 845 360 332 150 192 N2 90S 1,1 895 360 372 150 212 N2 90L 1,5 940 390 372 190 212 N3
80 0,75 845 360 332 150 192 N2 90L 1,5 920 390 372 170 212 N3
132S 7,5 1055 450 440 210 260 N4 160M 11 1185 490 460 230 260 N5 32/160 40/200 32/160
160M 11 1185 490 440 230 260 N5 160M 15 1185 490 460 230 260 N5 40/125 50/125 40/125
160M 15 1185 490 440 230 260 N5 160L 18,5 1235 490 460 230 260 N5 50/160 40/160
160L 18,5 1235 490 440 230 260 N5 180M 22 1285 490 480 230 280 N5 50/200 40/200
90L 1,5 940 390 420 190 240 N3 90L 1,5 940 390 440 190 240 N3 pos. 34 13
100L 2,2 955 390 420 190 240 N3 100L 2,2 955 390 440 190 240 N3 bearings 3208 3307 NU 306
100L 3 955 390 420 190 240 N3 100L 3 955 390 440 190 240 N3 pos. 17 39
112M 4 975 390 420 190 240 N3 112M 4 975 390 440 190 240 N3 el. seal ring 28 - 40 - 7 28 - 40 - 7
TAB. 2
pump flanged connections DIN 2501 - PN 16 pump dimensions shaft spacer pump fixing
model OUTLET INLET
DN k l q DN k l q a1 f h1 h2 d p m2 n2 n3 s1 s2 w
32/125 32 100 M16 4 50 125 M16 4 80 385 112 140 24 100 70 140 110 M12 M12 285
32/160 32 100 M16 4 50 125 M16 4 80 385 132 160 24 100 70 190 110 M12 M12 285
40/125 40 110 M16 4 65 145 M16 4 80 385 112 140 24 100 70 160 110 M12 M12 285
40/160 40 110 M16 4 65 145 M16 4 80 385 132 160 24 100 70 190 110 M12 M12 285
40/200 40 110 M16 4 65 145 M16 4 100 385 160 180 24 100 70 212 110 M12 M12 285
50/125 50 125 M16 4 80 160 M16 8 80 385 132 160 24 100 70 190 110 M12 M12 285
50/160 50 125 M16 4 80 160 M16 8 100 385 160 180 24 100 70 212 110 M12 M12 285
50/200 50 125 M16 4 80 160 M16 8 100 385 160 200 24 100 70 212 110 M12 M12 285
TAB. 3 TAB.4
Base fixing Anchor bolts Max loads on port sections
fixing Max loads MANDATA direction & sense direction & sense
BASE L1 L2 L3 B2 B3 t e r BASE daN ±x ; ±y ; +z - z ΣF ±x ; ±y ; ±z ΣM
(~=kg) force (daN; ~=kg) Moment (daNm; ~=kgm)
N2 800 130 540 360 320 18 M16 50 N2 13 DN 32 40 25 75 8 14
N3 900 150 600 390 350 18 M16 50 N3 42 DN 40 50 30 105 8 14
N4 1000 170 660 450 400 22 M20 55 N4 56 DN 50 60 35 115 9 15
N5 1120 190 740 490 440 22 M20 55 N5 126 DN 65 70 35 135 11 18
N6 1250 205 840 540 490 23 M20 60 N6 146 DN 80 80 40 150 11 18
dimension in mm
TAB. 6 NOMINAL DUTY POINT CONTRACTUAL DATA
pump 2 poles 4 poles
model capacity head efficiency capacity head efficiency mediu w.order
m
3 3
ZGE m /h m % m /h m %
32/125 13 22 51 6 6 45
32/160 15 32 50 8 8 50
40/125 22 24 45 11 6 45 conc. temp.
40/160 34 36 53 17 9 52 % °C
40/200 38 56 60 18 14 60
50/125 50 24 64 24 6 65 capacity head
50/160 60 40 68 30 9,5 65 m³/h m c.l.
50/200 50 60 67 25 14 63
b3 b4
pump casing
P1 = pump
P3 P4 pump rotor + base
+ motor
motor
base P2 = pump
+ base
P3 = pump
(= pump casing
+ pump rotor)
P2
b2 P1
b1 P4 = pump rotor
TAB. 7 Weight ref. to version: WR, ER, WF; +2% version QR; +6% version FC Centre of gravity along the rotation axis
Centre of gravity: location Centre of gravity: location Centre of gravity: location Centre of gravity: location Centre of gravity: location
Weights Weights Weights Weights Weights
pump daN; (~=kg) mm pump daN; (~=kg) mm pump daN; (~=kg) mm pump daN; (~=kg) mm pump daN; (~=kg) mm
model P3 b3 model P3 b3 model P3 b3 model P3 b3 model P3 b3
32/125 40 231 32/160 45 216 50/125 46 230 40/200 58 220 50/200 62 230
40/125 P4 b4 40/160 P4 b4 P4 b4 50/160 P4 b4 P4 b4
28 218 29 218 29 218 31 218 32 218
base P2 b2 base P2 b2 base P2 b2 base P2 b2 base P2 b2
N2 65 304 N2 70 289 N2 71 306 N3 88 310 N3 92 314
N3 70 333 N3 75 318 N3 76 334 N4 98 350 N4 102 351
N4 80 375 N4 85 359 N4 86 376 N5 113 405 N5 117 404
N5 95 433 N5 100 416 N5 101 433
motor P1 b1 motor P1 b1 motor P1 b1 motor P1 b1 motor P1 b1
N° - - N° - - N° - - N° - - N° - -
poles - kW - poles - kW - poles - kW - poles - kW - poles - kW -
2 1,1 75 358 2 3 98 421 2 4 106 462 2 7,5 162 538 2 11 207 623
1,5 78 373 4 105 445 5,5 141 550 11 203 627 15 227 648
2,2 86 408 5,5 140 533 7,5 150 567 15 223 652 18,5 247 669
3 93 438 7,5 149 550 11 191 657 18,5 243 673 22 282 715
4 100 463 11 190 639 15 211 680 22 278 720
5,5 135 550 15 210 663
7,5 144 566
11 185 655
4 0,18 69,5 327 4 0,37 77 324 4 0,55 81 356 4 1,1 101 366 4 1,1 105 367
0,25 71,5 338 0,55 80 341 0,75 82 362 1,5 105 383 1,5 109 383
0,37 72 341 0,75 81 345 1,1 84 373 2,2 110 405 2,2 114 404
0,55 75 357 1,1 83 356 1,5 93 411 3 113 415 3 117 413
0,75 76 362 1,5 92 394 4 121 440 4 125 439
1,1 78 373
Functioning (average values) Functioning (average values) Functioning (average values) Functioning (average values) Functioning (average values)
Sound pressure level dB 65 Sound pressure level dB 67 Sound pressure level dB 66 Sound pressure level dB 67 Sound pressure level dB 68
Vibration velocity mm/s 1 Vibration velocity 1,2 Vibration velocity 1 Vibration velocity 1,3 Vibration velocity 1,7
mm/s mm/s mm/s mm/s
Temperature of support °C 70 Temperature of support °C 70 Temperature of support °C 70 Temperature of support °C 70 Temperature of support °C 70