Condensate recovery solutions

Reduce your operating costs through the effective

management of condensate
STEAM & CONDENSATE
MANAGEMENT SOLUTIONS
c o n d e n s a t e r e c o v e r y s o l u t i o n s

Spirax Sarco’s range of condensate recovery solutions are

specifically designed to efficiently remove and recover
condensate under all operating conditions

Lower operating costs through How can returning condensate

efficient condensate management save you money?
Returning hot condensate to the boiler reduces the
In today’s energy conscious environment, condensate
costs associated with water treatment and make-up
has become a valuable resource that can be used to
water:
significantly improve steam plant efficiency.

Returning the highest possible percentage of Lower make-up water costs

condensate back to the boiler offers an exceptional When condensate leaves the steam trap, it still
return on investment by helping to cut energy and contains approximately 25% of the original heat
maintenance costs. Even recovering small quantities, energy that was within the steam before condensing.
such as the discharge from a single steam trap will, If this hot condensate is not recovered and returned to
over time, result in a significant saving. the boiler, the boiler would need to be continually fed
with cold make-up water.

Lower chemical costs

Why should condensate be Reducing the amount of fresh water make-up that
removed from your process enters the boiler also substantially lowers the amount

equipment? of water treatment required - again lowering operating

costs.

Removing condensate from your heat exchange and

process equipment not only improves efficiency, it will Compliance with environmental effluent standards
also provide more stable operating conditions and Restrictions and environmental regulations on the
prolong equipment life. quality of the water returned to the public sewer, apply
in most countries and effluent charges and fines may
Efficient condensate removal prevents: be imposed by water suppliers for non-compliance.
• Unstable temperature control Therefore higher costs are imposed if condensate is
drained into a sewer rather than being returned to the
• Product quality problems
boiler.
• Excessive corrosion of heating surfaces

• Waterhammer Boiler feedwater quality

• Noisy operation Since condensate is distilled water, which contains
• Equipment damage almost no total dissolved solids, returning more
condensate to the feedtank reduces the need
Utilising a Spirax Sarco condensate recovery system to for blowdown. This reduces the concentration of
effectively collect hot condensate from the steam and dissolved solids in the boiler water, which in turn,
return it to the boiler house can pay for itself within a lowers the amount of energy lost from the boiler
short period of time. through boiler blowdown.
spiraxsarco.com

3
c o n d e n s a t e r e c o v e r y s o l u t i o n s

Mechanical fluid pumps -

The sustainable solution to energy cost control

Spirax Sarco offer a complete range of mechanical fluid pumps specifically designed to remove and recover condensate
under all operating conditions, optimising plant efficiency and product quality throughout your plant.

Mechanical fluid pumps are typically installed with a receiver vented to the atmosphere – in what is usually termed an ‘open’
system - where condensate is collected from multiple steam traps and is pumped to the boiler feedwater tank.

Mechanical fluid pumps are best used where multiple condensate sources are present and where it is practical to install
a vent pipe.

Material SG Iron Stainless steel Steel

Model MFP14 MFP14SS MFP14S PTF4 PTF-HP
Body design rating PN16 PN16 PN16 ASME 150 ASME 150
Inlet Outlet

TABLE
1” (DN25) 1” (DN25) ●
1 ½”(DN40) 1 ½”(DN40) ●
2” (DN50) 2” (DN50) ● ● ●
Size

3” (DN80) 2” (DN50) ● ●
4” (DN100) 4” (DN100) ●
PMO Maximum operating
13.8 bar g 10.9 bar g 13.8 bar g 13.8 bar g 20.7 bar g
pressure
TMO Maximum operating
198ºC 188ºC 198ºC 198ºC 343ºC
temperature
Maximum
Max 19.3 litres 12.8 litres 12.8 litres 102 litres 60.6 litres
pump discharge/cycle
Maximum nominal capacity
Maximum 5 500 Maximum Maximum Maximum Maximum
(at 8 bar g operating pressure
kg/h 3 300 kg/h 3 300 kg/h 21 000 kg/h 8 000 kg/h
and 1 bar g backpressure)
Note: Pump capacities are only for comparison between pump models. Please refer to product specific technical information sheets
(TI’s) for the full capacities of each model.
 spiraxsarco.com

Features and benefits of mechanical fluid pumps

• No electrical supply required - each pump is a self-contained unit

which uses steam or other non-volatile pressurised gas as its motive
power, so there are no electric motors or level switches, which makes
installation easier. Ideal for humid, wet or remote areas

• No cavitation - able to pump high temperature fluids without cavitation,

reducing plant maintenance problems

• Fully automatic and self-regulating - only operates when needed

with no sensors or controls required

• Lower maintenance costs- no mechanical seals

or packing glands to leak

• Low running costs - motive power supplied is

typically steam. Maximum steam consumption
is typically less than 20kg/h

• Electronic pump monitoring - easy to calculate

the volume of pumped fluid*
MFP14
• Optional insulation jacket
- prevents heat loss

• Packaged units available

- fully assembled, tested unit that is
delivered to site ready to connected
to your system

• Intrinsically safe
- versions available for use
in hazardous environments

Disc check valves can be

supplied as an optional extra

*not suitable for use where

 intrinsic safety required.

5
c o n d e n s a t e r e c o v e r y s o l u t i o n s

Mechanical fluid pumps - Typical applications

Condensate recovery (open system)

Pumping high temperature condensate without cavitation or mechanical seal problems. Provides maximum heat
energy recovery.
Condensate
from multiple Vent to Motive media
steam traps atmosphere (steam or other gases)

Condensate
collecting receiver

Condensate

Condensate removal from process vessels and heat exchangers (pump / trap combination, closed system)
Removal of condensate under all pressure conditions ensures stable temperatures. It also prevents bottom end tube corrosion
and potential waterhammer and freezing.

Heat exchanger

A soft seated check valve

should be fitted to prevent
ingress of air

Condensate
collecting receiver
 spiraxsarco.com

Condensate removal from vacuum equipment

Simple and efficient solution to a difficult problem without the need for expensive electrical pumps and sensors.

Vacuum heat exchanger / receiver

7
c o n d e n s a t e r e c o v e r y s o l u t i o n s

PTF4 - for high capacity applications

®
The Pivotrol PTF4 high-capacity pump is capable of
pumping up to 40,000 lb/hr in rapid-cycling process
environments and under elevated pressure and
temperature conditions. Designed as a solution to
excessive maintenance and energy consumption
common with high-capacity condensate pumps used
in large commercial and industrial facilities, the PTF4
offers higher performance than conventional technology,
yet in a smaller package.

Features and benefits of the PTF4

• Low filling head - Easy to install in confined environments

• Pump mechanism replaces old technology of pins and linkages with virtually wear and friction free pivots
- increased service life and reduced maintenance costs

• Lifetime warranty on spring as standard - Inconel® compression spring for peace of mind

• PowerPivot® technology utilises carbide materials, which provide extreme hardness and resistance to wear
- increased service life and reduced maintenance costs

• Maximum operating pressure of 200 psig (13.8 barg) - high motive pressure increases pumps capacity rating

• Option to install cycle counter - allows energy returned to the boiler house to be monitored

• Integral hydraulic paddle - reduces high impact forces on the mechanism,

motive and exhaust valves during operation increasing service life.
spiraxsarco.com

9
c o n d e n s a t e r e c o v e r y s o l u t i o n s

Automatic pump traps -

Mechanical fluid pump and steam trap units combined

Spirax Sarco’s range of automatic pump traps have been designed to help you achieve optimum performance from all types of
temperature controlled process equipment, by removing condensate under all operating conditions.

Automatic pump traps are typically used to drain a single piece of heat transfer equipment, such as a heat exchanger,
which usually involves fitting a small condensate collecting receiver between the equipment and the pump-trap. Since the
receiver is not vented, this is most often referred to as a closed system.

The equipment is drained under all operating conditions, so it will not be susceptible to waterlogging or stall. The condensate is
usually recovered and returned to the boiler feedwater tank.

Automatic pump traps should be used when the operation of temperature controls on plant equipment such as heat exchangers
can create a ‘stall’ condition, whereby insufficient differential pressure is available for effective condensate discharge.
 spiraxsarco.com

Why is it essential to drain the system properly?

Problem: an air heater suffering the effects of stall

Under stall conditions, partial or complete
waterlogging may occur leading to:

• Temperature fluctuation - reduced heat

output / reduced product quality. Steam

• Corrosion of heating surfaces The control valve is throttling

to meet a reduced heat load.
- damage to heat exchanger. Hot air Condensate
Steam
• Waterhammer noise and damage
- mechanical stress on heat exchanger Cold air
and pipework.

Cold air
Waterlogged
The ultimate effect of stall is increased condensate
Steam trap set

maintenance and shorter service life of the

heat exchanger and associated equipment.
This increases overall running costs.

Solution: an air heater battery with APT installed

By installation of an APT into your application these issues will be eliminated. The APT automatically reacts when a rise in
condensate is detected, ensuring the application can continue to operate efficiently and effectively:

• When the steam pressure is sufficient to overcome the total backpressure (including static lift) the pump function will be
inactive. The trap will modulate to match the load and allow smooth condensate discharge.

• When the upstream steam pressure falls below the total backpressure, the pump will automatically detect a rise in
condensate level and discharge the condensate utilising the motive supply, thus preventing waterlogging of the steam space.

Steam

The control valve is throttling

to meet a reduced heat load.
Condensate
Hot air
Steam

Cold air

Cold air

APT

11
 c o n d e n s a t e r e c o v e r y s o l u t i o n s

Features and benefits of

Automatic pump traps:
• Compact design which contains all the equipment
needed to drain or remove condensate for all load
conditions including vacuum (innovative patent applied
for low profile mechanism).

• Minimal installation space required - The mechanism

operates with as little as 200mm installation head from
the base of the pump.

• Requires no electrical power, therefore suitable for

hazardous environments

• Fully automatic and self-regulating - only operates

when needed - No sensors or controls required.

• Packaged units are available - fully assembled,

tested packaged units can be delivered to site ready for
connection to your system.

Material SG Iron Steel

Pump type APT10-4.5 APT14 APT14HC APT14SHC
Body design rating PN10 PN16 / ASME 150 PN16 / ASME 150 PN16 / ASME 150
Inlet Outlet
¾” (DN20) ¾” (DN20) ●
Size

1½”(DN40) 1” (DN25) ●
2” (DN50) 1½”(DN40) ● ●
PMO Maximum operating pressure 4.5 bar g 13.8 bar g 13.8 bar g 13.8 bar g
TMO Maximum operating temperature 155ºC 198ºC 198ºC 198ºC
Maximum pump discharge / cycle 2.1 litres 5.0 litres 8.0 litres 8.0 litres
Maximum trapping capacity
1000 kg/h 3000 kg/h 7000 kg/h 7000 kg/h
(at 4.5 bar differential pressure)
Maximum pumping capacity
(at 4.5 bar g motive pressure 330 kg/h 620 kg/h 1000 kg/h 1000 kg/h
and 2.5 bar g backpressure)

Note: Pump capacities are only for comparison between pump models. Please refer to product specific technical information sheets (TI’s)
for the full capacities of each model.
Automatic pump traps - Typical installation

Condensate removal from process vessels and

heat exchangers
Designed for closed or sealed systems especially
where space is limited. Removal of condensate
under all pressure conditions ensures stable operating
temperatures of the heat exchange interface. Tube
corrosion, noise and waterhammer are all avoided -
extending equipment life.

Condensate removal from tube heat exchangers

(closed system)
The APT is simply connected to the outlet of tube
heat exchanger. Generally vacuum breakers are not
required provided that equipment is suitably rated for
operation under full vacuum conditions

The APT will drain condensate under all load

conditions, giving exceptional temperature control at
the heat exchange interface.

Condensate removal from vacuum equipment

(closed system)
Simple and efficient solution to a difficult problem.
Without the need for high Net Positive Suction
Head NPSH, the APT will operate with only
0.2 m installation head from the base of the
pump, and remove condensate from a vacuum
vessel, discharging it to either high or low level
condensate return lines.

13
c o n d e n s a t e r e c o v e r y s o l u t i o n s

Packaged pumping units

Our packaged pumping units (PPU’s) are made to fit directly into your
system with minimal interruption to your process. As the package is
pre-assembled, installation is fast and easy, ensuring you receive the
benefits associated with efficient condensate removal sooner.

We provide PPU’s in a range of sizes and connections, and we can

help advise you select the most suitable unit for you application.

MFP14 pump package unit

Features and benefits of Packaged pumps:

• Complete package, ready to use - Quick to install so shorter plant down-time

• Both PN and ANSI external connections - Convenient and flexible to install

• Hydro-tested assembly to 24 bar g - Certified safe operation

• Modernised design, modular construction - Upgraded quality, functionality

• Increased capacity - Standard solution for systems with large condensate return.
spiraxsarco.com

15
 spiraxsarco.com

Operating Companies Sales Offices Distributors

EMEA EMEA EMEA

Belgium Netherlands Austria Algeria Ivory Coast Oman
Czech Republic Poland Hungary Bahrain Kuwait Qatar
Denmark Portugal Jordan Bulgaria Latvia Saudi Arabia
Egypt Russia Kenya Cameroon Lebanon Slovenia
* Finland South Africa Romania Croatia Lithuania Sudan
France Spain Slovak Republic Cyprus Madagascar Syria
Germany Sweden Ukraine Ethiopia Malawi Tanzania
* Ireland Switzerland Estonia Malta Uganda
Italy Turkey Americas Ghana Mauritius Zambia
Middle East * UK Colombia Greece Morocco Zimbabwe
Norway Iceland Namibia

Asia Pacific Israel Nigeria

* Americas Chile
Hong Kong
* Argentina *Mexico Kazakhstan Americas
Brazil *USA Vietnam Bolivia Honduras Paraguay
Canada
Costa Rica Jamaica Peru
Dominican Republic Netherland Antilles Trinidad and Tobago
Asia Pacific Ecuador Nicaragua Uruguay
* Australia New Zealand El Salvador Pakistan
China Philippines Guatemala Panama
India Singapore
Indonesia South Korea
Asia Pacific
Japan Taiwan
Bangladesh Fiji
Malaysia Thailand
Cambodia Myanmar
* Manufacturing sites

Spirax-Sarco Limited, Charlton House, Cheltenham,

Gloucestershire, GL53 8ER, UK
T +44 (0)1242 521361
F +44 (0)1242 573342
E [email protected]

SB-S71-02 ST Issue 1 © Copyright 2015 Spirax Sarco is a registered trademark of Spirax-Sarco Limited