QUICK PROGRAMMING GUIDE FOR ALL RTS MOTORS

Altus RTS 120 V / Sonesse 30TM 24V / WirefreeTM Roll Up LT-30RT Round Head & CORD Lift CT-32 Motors.
Please refer to individual instructions for more details

Programming Mode STEP 4: Set the limits

Before you begin Bring the shade to desired upper limit stop point. Press both
Motors are shipped without limit settings and transmitter ID’s. Steps 1 to 7 must (Stop) and until the motor moves, then release. (If the shade
be completed to ensure proper shade programming and functionality. Power should stops when the buttons are released take it back to the upper limit
ONLY be connected to current shade being programmed. All other shades should be
disconnected from their respective power while programming and repeat) Stop the motor when reaching the desired lower limit.
You can adjust by pressing or
STEP 1: Connect power
With the motor installed in shade, connect power to STEP 5: Set the limits
the motor (120V, or 12 V or 24V transformer or 12 V Press both (Stop) and at the same time until the
battery wand) shade moves, then release. The shade will stop at the original
upper limit.
STEP 2: Initiate programming
Press both and at the same time until the shade
jogs. A jog is a brief up and down motion. In Programming
Mode, the shade will move only when the or is held STEP 6: Confirm limit settings
Press and hold (stop) until the shade jogs to confirm
the limit settings. A jog is a brief up and down motion.

STEP 3: Check directions STEP 7: Set user mode

Press or . When pressing product should Press and hold the programming button on the
go down or out. To change direction press and hold back of the transmitter until the shade jogs. The
(Stop) until the shade jogs. A jog is a brief up shade is now in User Mode. In User Mode, the
and down motion. shade will operate with a brief press on or
Double check limit settings as a precaution.

Adjusting the limits in User Mode

To change the lower limit Press both and at the same Press until the shade jogs
Send the shade to it’s current time until the shade jogs. Adjust to
lower limit. a new lower limit position.

To change the upper limit Press both and at the same Press until the shade jogs
Send the shade to it’s current time until the shade jogs. Adjust to
upper limit. a new upper limit position.

Setting an Intermediate Position (Preferred Position)

Setting Using
Press the or to operate shade. At the desired intermediate Send the shade to the intermediate position by pressing (stop)
(preferred) position press (Stop) to stop the shade. from ANY shade position.
Note: Shade should be stationary prior to activating intermediate
position function.
Once the desired Intermediate position is reached, Press and
hold (stop) until the shade jogs. The Intermediate position Note
is now added to memory If shade is actively moving (in-motion) Should be pressed twice.
To Delete: Activate shade to intermediate position, then press and
hold (stop) for 5 seconds. Shade will jog to confirm deletion.

Adding or deleting a Transmitter or a Channel

Programmed Transmitter
Transmitter To Add
Progammmed

STEP 1: Using already programmed transmitters select the transmitter (single channel) or the channel, (1-5)
Transmitter

Or Delete

of a multi-channel transmitter.
STEP 2: Press and hold the programming button of that transmitter until the shade jogs.

Transmitter to add or delete

STEP 3: Select the transmitter (single channel) or the channel, (1-5) of a multi-channel transmitter, to be
added or deleted.
STEP 4: Press and hold the programming button of that transmitter until the shade jogs.
 Resetting WIREFREETM ROLL UP MOTORS LT-30RT Round Head 12V DC Program
Button
To delete all previous settings: Using a paper clip, press and hold the PROGRAM button located on the motor
head. The LED will light then blink; release the button when the LED turns off. If you cannot see the LED, push
and hold the programming button for 15 seconds, and then release the button. All transmitters and limits will
be erased. (Motor is now reset to factory mode). Motor limits will need to be reestablished. See Programming
Mode (step 4&5) for limit setting.

Resetting WIREFREETM CORD LIFT MOTORS CT-32 12V DC

To delete all previous settings: press and hold the PROGRAM button (approximately 15 seconds) until Insert reset tool into
the LED blinks rapidly then extinguishes. All transmitters and limits will be erased. (Motor is now reset connector on motor.
to factory mode). Motor limits will need to be reestablished. See Programming Mode (Step 4&5) for Program
limit setting.
Button

Resetting Sonesse 30TM 24V DC

Program
To delete all previous settings: Using a paperclip, press and hold the red PROGRAM button (approximately Button
15 seconds) until the shade jogs 3 times. All transmitters and limits will be erased. (Motor is now reset to
factory mode). Motor limits will need to be reestablished. See Programming Mode (Step 4&5) for limit
setting.

TM
Resetting TILT WIREFREE RTS MOTORS 12V DC
To delete all previous settings: Using a paperclip, press and hold the PROGRAM button, located on the top of
the motor casing for 12 seconds. All transmitters and limits will be erased. (Motor is now reset to factory mode.)
Motor limits will need to be reestablished. See Programming Mode (Step 4&5) for limit setting.

Resetting Altus RTS 120 V AC

Perform a Dual Power Cut to delete all previous settings When the shade stops press and
hold the programming button
1 2 3 4 of any transmitter until the
shade jogs twice.

Do not release the programming

button until the jogging is
complete or you will have to
start the dual power cut from
the beginning.
2 Seconds 10 Seconds 2 Seconds Shade starts to move.

Activating Step (Tilting) Feature for Sheer Shade Applications

TM
(With WIREFREE ROLL UP MOTORS LT-30RT Round Head only)
1) Press , shade will travel to pre-set DOWN limit.
2) Press and hold until shade begins to “step” or tilt.
3) Release once new position is reached.

Tel. 1-800-667-6639 © SOMFY ULC 02/09 TI N B Y